Search Documents

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By Victor Spironello

The Bureau of Mines is studying cupola ironmel technology with the objectives of conserving high-quality raw materials through substitution and productivity. In the research re-ported here, a ize was modified by a gas-fired melting and/or ing chamber into the stack above the level of the coke bed, for study as a prototype for a coal-fired melting chamber. The modified cupola, in which natural gas was used to partially replace foundry coke, was evaluated in several trial runs. Data were obtained on furnace performance, metal and slag chemistry, and scrubber waters as particulates. Results of the modified ion were compared to those of conventional cupola operation. Although this research was preliminary--since the ultimate goal is to use pulverized coal instead of yielded ample evidence that the melting rate of a cupola can be icantly increased with less than a increase in energy input. Other evidence suggests that melting of low-density scrap can be enhanced and that scrap containing undesirable and/or oxidizable elements can be appreciably upgraded. This work is continuing and will include the use of pulverized coal of low rank to assist in melting.

Jan 1, 1984

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By W. H. MacLean, S. Liaghat

Abstract- The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographie means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8% carbonate, 60Jo chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/Ybn. = 1.7 to 2.8, Si02 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y =9, LaN/Ybn. = 4 to 8, Si02 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of Fep3 (27% total iron), Si02 (14%), CaO (8%), S and K20 ( + 2%), were added, Na2O was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By C. E. Jordan

The fundamental properties of dielectric separation were studied to provide insight into the design and operating characteristics of a dielectric separator. Force equations on mineral particles were derived and evaluated experimentally. Responses to variations in the electrical voltage and frequency, feed rate, particle size, dielectric fluid, and dielectric constant were tested theoretically and experimentally, using a 5-cm-diam dielectric separator. High-dielectric mineral recovery was proportional to the calculated effective dielectric force volume (EDFV) that surrounded each drum-electrode wire. Electrode spacing was the most sensitive design parameter; spacing of less than 0.4 cm was required for a good separation. Dielectric separation was effective for separating minerals with dielectric constants that differed by approximately 2 or more.

Jan 1, 1985

By V. Coetzee

Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes.

Jan 1, 2006

By Michael Hamilton

Mineral resources have been identified at seven properties in the, Middle Fork Judith study area (fig. 1, and table 1). Commodities consist of silver, gold, copper, lead, zinc, and marble. Eleven properties (fig. 1 and table 2) have potential for discovery of silver, copper, lead, zinc, or sapphire resources. Of principle interest are the mineral deposits within contact zones between the Yogo intrusive complex and the surrounding Paleozoic sedimentary rocks. Contact alteration zones along the southern slopes of Yogo Peak have been prospected in a 2- to 3-mi (3.2-to 4.8 -km) long belt within the study area.

Jan 1, 1982

Preparation of MgO Nano-Particles with Magnesite

Sep 13, 2010

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By Adriana Baldessin Costa

Na etapa de flotação de minérios finos de ferro, usa-se como agente depressor o gritz de amido de milho. Tal produto orgânico para ser usado como reagente precisa ser gelatinizado para permitir que os grânulos do amido tenham capacidade de absorver água quando molhados ou expostos à umidade. Este processo pode ocorrer por efeito térmico através de água aquecida ou por um ativador térmico como soda cáustica, sendo o último usado na planta Casa de Pedra. Visando aperfeiçoar a preparação/gelatinização do amido de milho buscaram-se auxiliares químicos para reduzir a presença de grumos suspensos (amidos não gelatinizados), aumentar a eficiência da ação depressora e garantir maiores ganhos de recuperação metalúrgica do metal de interesse. O trabalho contemplou estudos com um agente auxiliar denominado SOFTEX 2011 da empresa TENSAC. Os testes foram feitos em escala de bancada com substituição da massa total de água usada na 1ª gelatinização do gritz de milho (solução com 10% de sólidos) pelo reagente SOFTEX 2011 nas proporções de 1,0; 1,5; 2,0; 2,5; 3,0; 3,5 e 4,0%. Os primeiros resultados demonstraram ganhos significativos em recuperação metalúrgica e uma melhor seletividade das espécies minerais. Fisicamente, observou-se boa transparência nas suspensões do gritz de amido de milho gelatinizado através de um aspecto como gel.

Aug 1, 2018

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By Charles L. Kimbell

Although virtually every available indicator of world mineral industry activity demonstrated a gain in 1983 relative to the 2 very poor years of 1981 and 1982, the overall prospects for future years seemed far from bright. There were significant upturns in the quantity and value of mineral commodities produced, traded, and consumed in 1983, and many nonfuel mineral prices advanced, although the price advances in current dollars in most instances barely compensated for inflation. The pattern of investment in exploration and development of new mining ventures and new plant construction reflected virtual industry-wide concern that substantial upturns in demand for mineral commodities in the near future were unlikely, at least for most large volume products. The world oil glut continued despite cutbacks in production, and substantial stocks of many other mineral commodities mitigated against growth in total productive capacity, at least among market economy nations. In these countries, development activity at both mines and plants was confined largely to programs aimed at substituting new, more efficient installations for old, uneconomic or marginally economic plants. Among the centrally planned economy countries, the pattern was somewhat different on the whole, but even there, growth in total productive capacity was evidently somewhat restrained, although it seemed questionable whether the restraint was a function of intentional planning or simply an inability to accomplish planned programs on schedule. International political events, particularly the Iran-Iraq war and the unstable situation in the eastern Mediterranean countries (Lebanon, Israel, and Syria), continued to adversely affect mineral industry activities in those areas. Similarly, the internal and international conflicts in Central America negatively influenced mineral industry operations there. In Afghanistan, it appeared that there was some upturn in the very modest mineral industry operations, but industry activities there undoubtedly continued to be affected by confrontations between the Soviets and the local citizenry.

Jan 1, 1985

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By E. J. KENNEDY

THE 142D MEETING of the Institute is rapidly shaping up with splendid prospects of a strong technical program and the lighter side of this annual occasion amply provided for. The date is February 20 to 23. The technical sessions will be held in the Engineering Societies building; the smoker-dinner, the informal dance, and the annual reception and dinner, at the Commodore Hotel, Monday, Tuesday and Wednesday respectively. The news to date on the technical side is as follows: Mining Methods-Subsidence The Mining Methods Committee has prepared an interesting program which will be divided into two sessions to be held early in the week. At the first there will be papers on mining methods and development, including a description of the "Sinking and Equipment of No. 2 Shaft at Minas de Matahambre," by Dudley D. Homer and R. H. Cromwell. They describe in considerable detail the equipment used and the practice followed in sinking this important shaft, giving detailed costs and performance figures. Hoist¬ing ?arrangements and mining practice at the "Red Ore Mines of the Woodward Iron Co. at Bessemer, Ala.," are described by Tenny C. DeSollar, superintendent of mines, in a second paper. At this session of the Mining Methods Committee, H. M. Roche and R. E. Crockett, of the Committee on Eastern Magnetite Mining and Milling Methods, will present their paper, "Iron Ore Mining at the Scrub Oak Mine." This mine is in the highlands of New Jersey about 40 miles west of New York City. Prof. Robert K. Warner of Yale University will present a paper on "The Selection of a Mining System," which should have an interesting discussion. Pierre R. Hines, of Portland, Ore., will present, with stereopticon slides, his paper on "The Owyhee Tunnels, U. S. Reclamation Project, Owyhee, Oregon," describing one of the recent irrigation undertakings.

Jan 1, 1933

By J. MacFadyen

The U.S. cement industry experienced its best year ever during 2004 in terms of production and shipments of cement. Clinker, portland and masonry cements production and shipments were up considerably. Clinker production as reported to the U.S. Geological Survey (USGS) was 87.75 Mt (96.73 million st), an increase of 5.4 percent. Gray and white portland cement production from domestic and imported clinker was estimated to be 91.6 Mt (101 million st), up 5 Mt (5.5 million st) from 2003.

Jan 1, 2005

By Robert B. Parsons

"The Canadian mining industry is not off to a good start in the 1993/94 budget season. Of the five provinces and territories to table budgets as of March 31, 1993, the industry's scorecard shows: one win, one tie, and three losses.IntroductionBy the end of March, five of Canada's twelve provincial and territorial governments had tabled their 1993/94 budgets. The mining industry is off to a bad start. The industry's scorecard shows one win, one tie, and three losses. Only Newfoundland appears to be paying any attention to the industry's concerns about the impact of taxation on competitiveness. It is particularly disconcerting to see that non-profit based taxes continue to increase, at a time when these taxes are the focus of a united attack by the entire industry.NewfoundlandFirst, the good news. On March 18, 1993, Finance Minister Winston Baker announced the following changes to the province's mining tax regime:"

Jan 1, 1993

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990

By A. Mejias, M. A. Garcia, G. Diaz

During 1997 and 1998 two successful zinc feasibility studies, Skorpion and Sanyati, were carried out by Tecnicas Reunidas based on the modified ZINCEX® technology. The technical viability of each project was proved during more than 600 h of continuous running in a pilot plant. The Skorpion zinc project would recover 150,000 t SHG Zn/y from an oxidized zinc ore of a Namibian mine. The economical study showed that the plant would have the lowest production costs in the world. The Sanyati zinc project would treat a bleed from an existing copper refinery in Zimbabwe to recover 5,000 t SHG Zn/y. In the first case the electrowinning cellhouse was supplied by Union Miniere and in the second by Tecnicas Reunidas. This article highlights the pilot plant results and the advantages of the proposed process over conventional zinc production practices.

Jan 1, 2000

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982