Search Documents

By Milton Hood

The Copper Flat Property is located approximately 6 miles NE of the small town of Hillsboro in Sierra County, N. M. (Fig. 1). Hillsboro was the center of considerable mining activity in the late 1800's and early 1900's following the discover, of gold bearing vein deposits and later discovery of, placer gold along the east slopes of the Animas Hills. The Copper Flat orebody is a porphyry type deposit occurring in a small quartz monzonite porphyry stock that has intruded the center of a circular andesite plug (Fig. 2). The primary ore mineral is chalcopyrite. By-product values are contained in gold, silver and molybdenum.

Jan 1, 1983

By F. A. Schinner

The present study has investigated the leachability of cadmium sulfide minerals by Thiobacillus ferrooxidans and the electrochemical reactions involved in the process. Using a cyclic voltammetric technic and carbon-paste-CdS electrodes, it was found that the bio-oxidation of semiconductor cadmium sulfide minerals consisted of a number of intermediate electrochemical reactions. The overall reaction was found to be controlled by solid state diffusion as suggested by the chrono-amperometric and chrono-potentiometric measurements. The activation energy of solid state diffusion was determined by the Sand's method to be AE=24.3 kJ. A generalized mechanism was proposed for the bacterial oxidation of cadmium sulfide by T. ferrooxidan and an explanation given for the importance of high redox potential of leach solution versus the decomposition potential of the sulfide mineral. Furthermore, the effects of n-type or p-type character of CdS substrates relative to their bioleachability was discussed.

Jan 1, 1993

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980's. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,' the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill's Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By E. Lampard

Mines must manage variability from within their operations as well as those imposed upon them by external forces. This paper provides a framework to manage both internal and external variability through the review and adjustment of the mine plan where applicable to minimize lost production and maintain operational safety. KEYWORDS Mine plan, mine schedule, variability, safety, lost production, float days, update, adjustment, operations, Maintenance

May 1, 2011

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known, There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught fire, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By Luiz Henrique Dias Alves

O trabalho consiste na avaliação das Tensões Residuais através da técnica dos Furos-Cegos. O componente em estudo consiste em chapas de Aço A36 aplicadas para compor a estrutura de prensas hidraulicas. Com auxílio do software Solid Works versão 2013, foi realizado a simulação do estado de tensões sofridos pelas chapas quando a prensa hidraulica encontra-se em trabalho, determinando assim o seu fator de segurança. Em seguida, pelo método da aproximação sucessiva, foi adicionado furos-cegos ou furos passantes com diâmetros variados ao longo da geometria das chapas a fim de verificar o comportamento dos estados de tensões. Portanto, através da aplicação de furos-cegos nas chapas, foi possível identificar o diâmetro e posição ideal que permitiu um ganho significativo no fator de segurança das chapas, permitindo assim, reduzir o número de chapas no processo impactando diretamente nos custos e no tempo de fabricação do equipamento.

Oct 30, 2017

By W. W. Staley

This paper discusses the design of small head frames that will fill the needs of prospectors and small operators whose operations are conducted through shafts. The head frames considered were designed to handle relatively small tonnages. It was assumed that the shafts in which buckets are used would not exceed 300 feet in depth and that not over 60 tons of rock would be hoisted, in, 14 hours. In the design of the larger head frames, a hoisting capacity of about 250 tons per 6 hours from a depth of 300 to 500 feet was assumed. Under these conditions, hoisting speed, rate of acceleration, and weight of rope have a negligible effect on the head frame design and, therefore, have been ignored in the following, discussion. Because timber is relatively cheap and easily obtained in most mining areas, the discussion has been confined to timber construction.

Jan 1, 1937

By Joseph A. Holmes

The public is already familiar with the general fact that the scope and the financial resources of the approaching St. Louis World's Fair are much larger than those of any of the preceding great expositions; and both the visitor and the exhibitor, when he comes to St. Louis in 1904, will find it to be a real World's Pair, with exhibits and visitors from every known country. Passing over the subject, as to the general Exposition, with this brief statement, I ask Sour attention to the consideration of a few important facts connected with the proposed mining exhibits at this Exposition. First of all, I may say that. reading- and writing-rooms and library facilities will be furnished in the Mines Building for miners and mining engineers, and it is expected that when they visit the Exposition they will make these rooms their headquarters, and give the Chief of the Department and his assistants an opportunity to extend to them such courtesies as may be possible. One of the exhibits in the Mines Department will consist of models and maps arranged to show the nature and extent of the mining operations in the United States at the time of the purchase of the Louisiana Territory in 1803, the event which

Jan 1, 1903

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

By René Winand

A new process was studied at large laboratory scale at Université Libre de Bruxelles, under contract with Metallurgie Hoboken-Overpelt. A two cathodes (1m long ; 0.2 m high) channel cell was used at 2000 A/m2, with an electrolyte flow rate up to 1.8 m/sec. The main results may be summarized as follows : cathodes are electro¬refined grade in analysis ; metallographic structure and surface roughness are kept under control up to 1.3 cm (one side deposits) ; silver in cathode is controlled by CI and Br ions in solution ; organics must be used at very low concentrations (in the range of 0.1 mg/1, with a consumption of about 0.01 mg/lh).

Jan 1, 1987

By R. K. Singhal, H. Sahay

Introduction In terms of the world's recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world's total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada's total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950