Search Documents

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

In the present work, the effect of pH, non-ionic polyacrylamide flocculant and anionic polyphosphate on rheology and settling behaviour of colloidal TiO2 suspensions (15 ? 50 wt% solid) is investigated. Maximum particle aggregation, reflecting in the highest suspension settling rate and maximum shear yield stress was achieved at pH 7.2, the isoelectric point (iep), consistent with DLVO expectation. However, the maximum aggregation condition at the iep also resulted in the poorest suspension consolidation behaviour. Significantly enhanced consolidation was achieved for a more dispersed suspension at pH values away from the iep but at reduced settling rate. Thus, when pH alone is used to control conditions which facilitate strong interparticle attraction, a high settling behaviour which is not conducive to compact consolidation results. Improved suspension consolidation may be achieved at the iep via anionic polyphosphate addition which leads to attenuation of the strongly attractive van der Waals forces and emergence of "soft" repulsion due to weak inter-particle electro-steric forces. The weak repulsion act to lubricate particles involved in the hydrodynamic interactions which controls the compressibility of the sediment bed, allowing a compact consolidation of solids to be obtained. Alternatively, non-ionic polyacrylamide homo-polymer (Magnafloc 333) was fairly effective in flocculating titanium dioxide suspensions leading to high settling rate and acceptable pulp consolidation at the iep.

Jan 1, 2006

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Leandro de Arruda Santos, Lorena Isabela de Oliveira Ribeiro, Jéssica Dornelas Silva, Pedro Damas Resende, João Victor Lucas Amim, Suzanny Cristina Soares Martins, Vicente Tadeu Lopes Buono

O objetivo do presente estudo foi avaliar a resistência à fadiga de duas ligas de NiTi diferentes sob condições de teste controladas por deformação a 25°C por meio de testes de fadiga por flexão rotativa. Além disso, as propriedades mecânicas, térmicas e estruturais dos fios foram caracterizadas por ensaios de DSC, DRX, MEV/EDS e tração. Os resultados revelaram que ambos os materiais são superelásticos à temperatura ambiente e, portanto apresentaram composição basicamente austenítica de sua matriz. Os resultados de ensaio de tração são condizentes com a caracterização térmica e estrutural, pois os materiais apresentam recuperação total de forma após ciclos de carga e descarga em tração. Ambos os materiais são ricos em titânio, um deles apresenta camada de óxido superficial enquanto o outro apresenta acabamento superficial. Apesar das propriedades similares a amostra 1 apresentou média de 77 ciclos até a falha, enquanto a amostra 2 resistiu a 1827 ciclos..

Oct 25, 2019

By William G. Doepken

With most of the mining industry emerging from the deepest business recession in 50 years, primary attention must be given to surviving in a business climate where dominant foreign competition, depressed prices, and potential overcapacity hang heavy over much of the industry. While already shackled with regulatory constraints, restrictive work rules, and high labor costs, mine operators are faced with the difficult task of reducing costs and improving productivity while operating at less than full capacity. To counter these nearly over-whelming factors, the mining industry must continue at the national level to seek regulatory relief and a rational policy toward foreign competition from government-controlled mines. In addition, dialogue with labor organizations must continue to minimize the impact of labor costs, cost escalators, and antiquated work practices. Although national and international actions have a tremendous impact on the future of domestic mining operations, local actions by mine operators to dramatically improve mining productivity will strengthen the industry's competitive stance. Before any substantial progress can be made, however, mine operators must recognize and define areas that depress productivity and establish goals and measures for improvement. Once problem areas are defined, a combination of technological and motivational concepts can be applied to improve productivity. Timing of Improvements While there is an immediate need for productivity improvements, only certain concepts offer near-term improvement potential while others must, of necessity, fit into a mid-range or long-range time frame. Near-term solutions (immediate to one year) likely will involve motivational concepts - work incentives and training - coupled with available technological concepts that require little capitalized development or site testing. Mid-range solutions (one to three years), by contrast, will include technological improvements in mining equipment, techniques, and systems automation. These concepts require a longer period of capitalized development and site testing before use. Long-range solutions (three years or more), which include adoption of new mining methods and computerized control systems, will appear only after prolonged research and capitalized development programs. Motivational Improvements Developing motivational con-

Jan 11, 1983

By Joan T. May

The Federal Bureau of Mines investigated the potential for recovering aluminum from copper-dump leach liquors by use of single-contact ion-exchange technology. A strongly acidic ion-exchange resin was used to extract aluminum from a typical dump leach liquor and from synthetic leach liquors. Aluminum was stripped from resin with a HS04 or NaCl solution. Bench-scale experiments indicate that a single-contact ion exchange is technically feasible, but that the process is limited by the relatively low loading capacity of the resin and the excessive amount of stripping agent required. A further limitation is that significant amounts of magnesium and iron are loaded and stripped along with the aluminum.

Jan 1, 1976

Supergene enrichment of ilmenite occurs through a complex series of reactions with initial oxidation and hydration followed by leaching and dehydration. Lateritization appears to be associated with the early phase of the supergene process and if ilmenite grains are encased in iron oxides no further alteration proceeds.

Jan 1, 1986

By David A. Benjamin

From 1986 to 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 59,600-acre Mexican Mountain Wilderness Study Area (UT-060-054) in order to evaluate its identified mineral resources. The study area is located in Emery County, UT, about 24 miles east of Castle Dale, UT. A review of the geologic and mining literature, and a field examination identified two uranium prospects in the Wilderness Study Area, and three copper prospects nearby. One-hundred ninety-five rock samples were taken.

Jan 1, 1989

By Noakes M. J

Research and development into alternate gold and precious metals adsorbents has resulted in the development of a new technology named the AUROSAVE adsorption process (ARGOSAVE'" for high silver con- tent ores). Adsorbents called VITROKELE'" can be tailored for either Gold I (cyanide leach) or Gold III (halide leach) applications. VITROKELE consists of a chemically synthetic adsorbent carried on an inert substrate, often a polystyrene bead. It is suitable for both in- pulp and in-solution use. VITROKELE adsorbent offers certain advan- tages over both carbon and ion exchange resin adsorbents. This paper describes testwork on Australian ores and commercial solu- tions obtained from operating Australian plants demonstrating the kinetic loading characteristics, elution methods and other operating parameters of VITROKELE adsorbent in the cyanide system. Brief reference is made to VITROKELE in the Gold III system.

Jan 1, 1988

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By Venancio Astucuri

"El presente texto describe las cuatro competencias que debe poseer un ingenierio de minas para un desarrollo sostenible de la minería. Dichas competencias se dividen en personales, académicas, profesionales y de ingeniería. Este grupo de competencias pueden ser usados también para un proceso de autoevaluación, donde cada uno pueda medir sus competencias con el fin de determinar brechas y superarlas, de forma que las empresas puedan plantear requisitos mínimos para sus diferentes posiciones laborales y, finalmente, para que en las instituciones educativas, estos puedan diseñar de forma adecuada sus respectivos planes de estudio."

Feb 1, 2017

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By Cameron Hams

Noranda's Process Reactor and Codelco's Teniente Converter are physically similar vessels, which leads to the commonly held misconception that the two processes are the .same. However, notable differences in chemistry, operating philosophy, and construction make them quite dissimilar. This paper compares and contrasts the Noranda Reactor and the Teniente Converter, and attempts to explain some of the apparent differences in behaviour and performance. The results of a worldwide survey of most operating Noranda Reactors and Teniente Converters, along with those processes that have ceased operation or are planning to be started-up in the future, are presented.

Jan 1, 1999

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By José Porras

El presente trabajo señala el proceso de optimización en la mina a través del área de Tecnología de la Información, superintendencias y las áreas directas de las operaciones. En ese sentido, durante el diagnóstico de todos lo procesos levantados como geología, planeamiento mina, operaciones mina, mantenimiento, logística, control de gastos, se determinó mejorar las oportunidades que generen valor, como las oportunidades de control y reducción de costos, gastos, y su relación con los resultados obtenidos en su ejercicio.

Sep 9, 2007