Search Documents

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By M. M. Jones

Natural brines are potential domestic resources of minerals. The brines of Searles Lake, CA, for example, contain an estimated one-fourth of our current reserve of tungsten. A key to Bureau of Mines research to recover this critical mineral is the ability to quantitatively measure concentrations of particular constituents in the large number of brine samples and process solutions produced under a multiplicity of test conditions. This paper describes procedures used to determine arsenic, boron, phosphorus, silicon, and tungsten in these solutions by simultaneous inductively coupled plasma spectrometry. A variable in-ternal standard method was used to compensate for tungsten interference on the other analytes in tungsten concentrates, and matching standards were used to determine tungsten in raw brine. Other solutions were analyzed using normal techniques. Analytes were determined down to 1 mg/L with an average precision of 2.5 pet relative standard deviation. Accuracy, estimated using synthetic solutions and by comparison with values obtained by other methods, averaged about 2.5 pet. The methods were rapid, required little sample preparation, and provided the needed sensitivity.

Jan 1, 1985

By Kwadwo Osseo‑Asare, Isehaq Al‑Nafai

The hydrometallurgical processing of bastnasite is a well-known process that is used to extract rare earth metals. However, more accurate measures are required to enhance the efficiency of extracting and recycling rare earths. In this work, Pourbaix (Eh–pH) diagrams for La-, Nd-, and Pr-(F)-(CO3)-(SO4)-(Cl)-(NO3)-(C2O4)-H2O systems were theoretically derived to investigate the stability relations during the hydrometallurgical processing of bastnasite. The diagrams for RE-H2O systems show similar trends to the original ones drown by Pourbaix. The stability domains of RE carbonates were presented by RE-CO3-H2O systems with pH range of 4.5–11. In contrast, the diagrams for RE fluorides showed a large stability region of insoluble REF3 (pH ~ − 1.7–12). The decomposition behaviors of REFCO3 were studied by constructing Eh–pH diagrams for RE-F-CO3-H2O system. The stability regions of bastnasite species extend from nearly neutral to basic media (pH ~ 6.5–12). The acid treatment (using H2SO4, HCl, and HNO3) of bastnasite was investigated by constructing Eh–pH diagrams for REF- CO3-(SO4)-(Cl)-(NO3)-H2O systems. According to these systems, REFCO3 can be decomposed at pH ~ 6.5 when treated with H2SO4 and at pH ~ 1.7 when treated with HCl and HNO3 acids. On the other hand, the alkaline treatment of REFCO3 converts it to RE(OH)3 at pH ~ 11. The recovery of rare earths ions was studied with the aid of RE-C2O4-H2O systems which shows a wide stability region for RE oxalates in pH range of − 2–11. This theoretical approach explained the aqueous relations in the hydrometallurgical processing of bastnasite ore and it can improve the practical hydrometallurgical processing of such ores.

Feb 9, 2024

By Graham Bright

T HE chairman of the Mines Committee of the A. 1: E. E. for 1920-21 has had the honor of being also the chairman of a similar committee, the Mine Equipment Committee, of the A. I. M. E. It has been the endeavor during the past year to have the two committees work together since the object of these committees is very much the same. A meeting of the committees was held in Chicago in November of 1920, at which time it was decided that one of the best ways to work together would be to foster joint meetings of the local sections of the A. I. E. E. and A. I. M. E. By these meetings, it was hoped that various engineers in the local sections interested in mining subjects could be brought together and not only become better acquainted but be greatly benefited by the interchange of ideas and by the discussion of papers presented on mining subjects.

Jan 1, 1921

The Australasian Institute of Mining and Metallurgy (AusIMM) is a professional society for all those associated with the activities of the mineral industry. Differences of opinion exist within the membership of the AusIMM on the role it should play in the future as a professional society in a changing industry and world environment. This same dilemma is concerning other professional societies of which the author is a member. Some of the activities and priorities of the AusIMM are reviewed in order to clarify a frequently expressed opinion that it identifies with and supports industry at the expense of representing the interests of its individual members. By definition and by action this is certainly not the case and it is concluded that all activities whether seen to be industry or member orientated serve to benefit both. The AusIMM plays a most important role in integrating and promoting the interests of all sections of the mineral industry whether corporate or individual and the Presidential activities in education this year provide an excellent example of this.

Jan 1, 1997

By R. J. Matetic

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the fieldsite. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 2010

By A. Ghahreman, M. Oliazadeh

"Heap leaching is an attractive process for low grade deposits where the metal content of ore does not justify the high cost of milling and agitated leaching. In general, the heap leaching capital cost is low, construction is rapid, and production costs are low. The primary disadvantage of heap leaching is low recoveries (typically 65% of agitated leach recovery); thus, recovery improvements could convert more lower-grade deposits into minable reserves. This will also allow to process primary sulfide ores and result in a dramatic expansion of the technology, as ~80% of total ore types are sulfidic in nature. The old gold operations tailings are another massive source of low-grade gold material that can be retreated by the heap leach process. The major parameters affecting the recovery rates are ore characteristics (mineralogy, particles size of metal and host minerals, ore permeability), and operational conditions (segregation of ore, compaction, leach cycle time, lift height, and solution application rates). The design of a percolation leach process is based on a limited number of coarse ore bottle roll and/or column tests under ideal conditions. The economics of the projects and engineering design of the process facilities are developed based on the bench scale test work results and the application of the conventional engineering scale up factors. This paper will deal with the parameters affecting the HL efficiencies and focus on the potential improvement of gold heap leach recoveries. This would include design of heap leach operation and evaluation of processes such as fine crushing and bioleaching.INTRODUCTION Gold heap leaching is a hydrometallurgical process designed to treat amenable low-grade gold ores that contain typically 0.5 to 1.5 g/t gold (Marsden and House, 2006; Wong Wai Leong and Mujumdar, 2010). Ore is stacked by various types of equipment on an impermeable barrier, and a sodium cyanide solution is applied to the surface of the stacked ore. Gold, silver, and other metals contained in the ore are dissolved to various degrees by the cyanide application, as it percolates downward through the stack of the ore. The pregnant leach solution (PLS) is then collected at the bottom of the heap. The PLS is then sent to the gold recovery plant where the metals are extracted. The barren leach solution (BLS) is then reapplied to the top of the pad. Ore is placed on a pad or previously leached lift by various means, including ramp conveyor belts, radial-arm and self-leveling stackers, and trucks. Once trucks are used to construct the pads, the pad can be compacted and hence the pad should be graded and ripped or scarified (roughened up) with wheeled or tracked equipment to produce shallow cuts to increase surface area exposure to the leachate."

Jan 1, 2019

By M. R. Barkhudarov

Semi-solid metal can be formed into useful products of near net shape and high quality. Use of this method has been limited, however, because of the difficulty of working with metal in the semi-solid state, which has strong shear rate, temperature and time-dependent properties. In this paper we describe a thixotropic model and apply it to the problem of small metal droplets impacting on a flat plate.

Jan 1, 1997

The mining industry has expanded significantly in the Pacific Region over the past two decades through a mix of new developments and brownfields expansions of existing operations. Despite this overall success there are also a number of well publicised examples of less than successful minerals ventures. These problem developments highlight the fact that success cannot be taken for granted and that rigorous planning and attention to detail is essential. The dominant growth has come through expansion of existing businesses, notably alumina, iron ore and coal, achieved through both efficiency gains on existing plant and step change capacity additions such as new mines and/or expanded processing plant. This expansion has largely been linked to increased market opportunities. The major issues are the quality and extent of the host resource, achieving the market targets, and the efficiency of the expansion effort. There can be also a range of site specific issues which need to be addressed. The development of new greenfields operations is often more complex as it can bring a wide range of new issues. Depending on the nature of the development, and the companies involved, these can extend from initial financing through to obtaining a market position. Incorporating major new technology and/or establishing infrastructure and attracting staff to remote locations can also add significant challenges. This paper outlines many of the critical factors which need to be considered prior to proceeding with major expansions or greenfields developments. These will be linked to a number of developments in the region over the past decade.

Jan 1, 2004

By Sami Hindstrom, Travis Orser, John Starkey

"A great deal of effort has been expended in the last 11 years by the authors and others to identify the correct power required to grind ore in a SAG mill, by developing ore hardness variability functions for the ore body to be mined. This paper describes the next step in the SAG design process, which is choosing a SAG mill to accomplish the required specified design performance.At the test work stage, each ore hardness data point is a unique and discreet bit of information that represents the energy required to grind the ore represented by that sample at optimum SAG conditions. When the design criteria are set, it is now considered necessary that the required power draw in the mill chosen be provided at optimum conditions as well.Based on actual 3-ft diameter pilot plant results, we can now show that the grinding efficiency and throughput drop when the optimum load limit is exceeded. Future work is expected to show a similar reduction in efficiency when exceeding optimum speed. Providing specified power by exceeding these optimum conditions is not adequate and leads to a lower cost but underperforming SAG mill.It is possible in some cases to modify a SAG circuit to force it to perform better, but this often takes time, much effort and costly modifications. In most cases the capital spent on a properly sized SAG mill may prevent production losses that would be many times greater over the extended start up period. This is the direct result of choosing the proper SAG mill at the start.INTRODUCTIONThe sequential steps required for the design of any grinding circuit, have changed dramatically in the last seven years. Previously, it was considered necessary to do six foot diameter SAG mill pilot plant tests on representative samples of minus six inch ore (F80), in order to understand design requirements. It can now be shown that this method is costly and not likely to produce the desired result because it is difficult to recover six-inch material from deep within a new mine. The representative nature of the sample is often compromised when the sample is selected."

Jan 1, 2003

By Anna Paula Littig Berger, Caio Vaccari Silva, Victor Bridi Telles, Felipe Fardin Grillo, José Roberto de Oliveira

No presente trabalho foi proposto uma análise da eficiência de desfosforação de uma mistura padrão M1 e outras três misturas, onde foi realizado um aumento progressivo da %FeO em sua composição química (5%,10% e 15%). Além disso, esta mistura padrão M1 foi testada utilizando-se CaO em duas granulometrias diferentes, uma mais fina (M1A) e uma mais grosseira (M1). Os testes experimentais foram realizados a uma temperatura de 1400°C, com agitação de 450 RPM, em um forno de resistência. Para a análise das propriedades da escória, foram realizadas simulações através do software de termodinâmica computacional FactSage 7.2 e análises de imagens obtidas da superfície do cadinho ao final dos experimentos no software Quantikov. A mistura M1 apresentou melhor desempenho do que as misturas onde foi adicionada uma maior quantidade de FeO, visto que foi observado que à medida que a %FeO nas misturas é aumentada, a eficiência de desfosforação diminui. Além disso, a utilização de uma granulometria grosseira mostrou-se mais eficiente do que a granulometria fina, devido a maior aglomeração causada por essa. Esses resultados corroboraram as equações utilizadas para calcular o Fator de Desfosforação (FDeP), calculado para correlacionar as propriedades termodinâmicas das misturas desfosforantes e a eficiência de desfosforação.

Oct 1, 2019

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

[Page Minutes 5 Present Status of Petroleum Industry 9 F. M. Van Tuyl. Developments Along the Line of Low Heat, Carbonization 13 A. C. Watts. Uses for Fine and Pulverized Coal 14 C. A. Allen. Have Mining Engineers Accepted All That Developments in Machinery Apply? 16 R. Dawson Hall. Coal Mine , Accidents and State Mining Law 23 D. Harrington. Harmony and Co-Operation 26 H. F. Nash. Personal Dangers 28 John Bevan. Methods of Improving Safety and Health Conditions 29 C. A. Allen and A. L. Murray. The Economic Relation of Accidents and Preventable Diseases to the Coal Mining Industry 39 Recent Developments in the Use of Electricity in Mines 43 Graham Bright. Discussion of Graham Bright's Paper 48 Mine Safety Work at Dawson, N. M 49 W. F. Murray. Mine Safety Work 54 Eli Follett. Wire Rope in Mining Operations 56 James F. Howe. Discussion of F. E. Shepard's Address 69]

Jan 1, 1922

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By P. Lostritto, G. E. Agar, G. Labonte, M. Cherevaty

"A locked cycle flotation test was done on a sample from the ovoid portion of the Voisey 's Bay copper-nickel sulphide ore. The chemical conditions for this test were generated by prior independent testing. In this test work the time in each of the five separation stages was optimized prior to executing the locked cycle test. A numerical simulation of the continuous circuit material balance was done prior to the locked cycle test. The test results were not fully satisfactory because the flotation of pyrrhotite in the bulk rougher and cleaner stages was not consistent. The preliminary indication was that the samples had oxidized to varying degrees during storage.INTRODUCTIONINCO has performed batch laboratory flotation testing on ore from Voisey's Bay which is a mixture of chalcopyrite, pentlandite and pyrrhotite. Earlier, Lakefield Research was contracted by Diamond Field Resources to test the ""flotability"" of the ore, which included a pilot plant trial. INCO's J. Roy Gordon Research Laboratory has repeated many of the batch tests that Lakefield did to verify their results. Based on their own work, INCO has modified the circuit proposed by Lakefield Research. The modified circuit is based on batch test work, but no locked cycle test (LCT) was done. It is believed that this circuit will produce a copper concentrate at 29-30% copper and a primary nickel concentrate at 15-20% with recoveries of 80% or above.For several years the University of Toronto has been working with INCO to provide ""hands on"" experience for undergraduate students as an Industrial Research Project (IRP). This year, the objective for IRP was to optimize the time for each of the five separation stages for the Voisey's Bay ore then to numerically and experimentally simulate the material balance for a continuous circuit."

Jan 1, 1998

By R. Panchadhara, P. A. Gordon

"A non-local formulation of the classical continuum mechanics theory called peridynamics is used to study driven dynamic fractures in the near wellbore region. The controlled application of pressure on the inner walls of the borehole can create multiple fractures that initiate from the borehole and propagate radially outwards. The number of fractures and their final length is primarily controlled by the loading conditions and the in-situ stress state. It is the objective of this study to use a novel numerical technique called peridynamics to investigate: 1) the influence of loading conditions on the fracture pattern, and 2) the effect of in-situ stress anisotropy on fracture propagation. In peridynamics, the momentum equation from the classical theory of solid mechanics is replaced with the integro-differential momentum equation of peridynamics. As a result, discontinuities in the body, such as fractures, occur spontaneously. The material is represented by a continuum body with material points that interact non-locally with all other points within a specified distance. Fractures evolve using a damage evolution law, wherein, damage at any point is represented as the ratio of the number of broken bonds in the current configuration to the total number of bonds in the undeformed configuration.Simulations are performed on simplified test cases and the results are compared to relevant experimental and numerical studies found in the literature. It is shown that the loading rate significantly influences the number of fractures initiated from the borehole as well as their extent. Low loading rate produces fewer fractures, whereas, high loading rates produce longer and a greater number of fractures from the borehole. The numerical method successfully predicts the fracture pattern obtained from a wide range of loading conditions. Predictions also indicate that the resultant fractures are shorter when in-situ stress is applied. Numerical results show that the fracture extension is largest in the direction perpendicular to the minimum compressive stress for the range of loading rates used in this study."

Jan 1, 2015

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023

By Pierre Gratton, Gordon Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM’s goal is to improve the mining industry’s performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move to external verification of their performance in 2006. The presentation will describe the initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector.

Jan 1, 2006

Market confidence is on the rise and industry leaders turning toward the vast and diverse region of Latin America are faced with abundant, yet daunting, opportunity. From the iron orebodies of Brazil to the renowned copper mines of northern Chile, drilling teams in Latin America are often faced with abrasive, broken ground. These types of ground conditions tear up coring bits rapidly, making it extremely difficult for even the most seasoned drilling teams to maintain effective productivity. The drilling challenges faced in this rich and opportune region are being met today by advanced coring technology, bringing with it the potential for increased productivity in Latin American mineral exploration.

Jan 3, 2010