Search Documents

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By Fernanda Margarido

Recovery of metals contained in the electrode materials of batteries was studied considering an integrated recycling process constituted by physical and chemical operations. The physical treatment included the shredding of the spent batteries, followed by a wet sieving operation of the fragmented material. The physical behavior of Ni-Cd and Zn-Mn based (alkaline and saline) system batteries was studied and compared. In that sense, shredding operation was performed and the sieving of shredded fractions was accomplished to evaluate the efficiency of the separation of electrodes and scrap. For Ni-Cd batteries the loss of electrode material with the supra fraction (scrap) after the shredding operation was lesser than the Zn-Mn batteries. Especially for saline-type batteries, the electrode attached to the scrap was substantial leading to important losses. This difference can be explained by the composition of the case materials and the internal physical constitution of the electrodes. The wet sieving studies carried out allowed optimizing the separation of the electrode fine fractions from the scrap materials through the analysis of selectivity Cd/Fe or Zn/Fe. For Ni-Cd batteries, maximum selectivity was achieved for the granulometry of 1.4 mm, while for alkaline and saline systems best selectivity were obtained at 2.8 mm and 5.6 mm, respectively. This process allowed the recovery of about 70% of electrodes for Ni-Cd and alkaline systems, and 50% for saline batteries, with less than 5% of scrap as contaminant. This physical step can be considered as a pre-treatment of this type of waste material envisaging its valorization by chemical treatment, as improves the concentration of the elements of interest and decreases the iron content.

Jan 1, 2006

By I P. Hodkinson

SMC Resources Limited is implementing a selective mining approach at the Hadleigh Castle mine, formerly operated by Aurora Gold Limited. The main ore zone has a length of 250 metres and dips at 40 - 45¦ to the south. Gold mineralisation occurs in a variety of quartz-sulphide lodes in sericitised granodiorite. Shallow dips, alteration intensity and mineralisation style combine to make mining relatively difficult. Previously unworked, high-grade, shallow dipping (30 - 45¦), narrow quartz-sulphide lodes within the hanging-wall of the deposit are also being selectively exploited. Annual production of 35 000 oz Au is forecast from 185 000 tpa ore grading 6.5 g/t Au over a currently envisaged mine life of six years. Operations completed to-date include deepening the decline and access development of the first two levels beneath the previous workings. Longhole stoping operations have commenced in the main ore zone with air leg stoping also underway in the hanging wall lodes.

Jan 1, 1998

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By D. Christofferson

This final report documents the cooperative efforts of the Engineered Systems Division and the Mining Equipment Division of FMC Corporation during performance of Bureau of Mines Contract H0252091. Improved operator compartments incorporating overhead canopies, logical arrangements of controls, and design features offering greater operator comfort were developed and retrofitted to the FMC 320A roof bolter and 6L shuttle care The vehicles were evaluated in underground operations at separate mine sites. The successful evaluation has resulted in incorporation of the designs as standard features of the 320A roof bolter, and the 5L, 6L, and 10L shuttle cars.

Jan 1, 1978

By R. J. Leary, W. M. Mahan, F. X. Tartaron

A new type of apparatus for prerefining molten blast furnace iron and to reduce the cost of subsequent steelmaking consists of a funnel - shaped device lined with firebrick into which a horizontal stream of molten pig iron is directed tangentially at the top . The rotary motion thus induced causes the stream to flatten itself upon the wall and flow in a spiral path to the outlet ; thus , the device was termed " vortex cone .' Oxygen and other refining agents are impinged upon the flowing metal in the cone where reaction is facilitated by the large metal surface exposed and the turbulent flow pattern . Experiments with water in 1 - foot - diameter funnels provided an idealization of the flow patterns to be expected with molten iron . A brick - lined reactor 3 feet in diameter was built for desiliconizing molten pig iron in lots of 1 to 2 tons . At flow rates of 0.3 to 0.5 ton min - 1 (430 to 720 tons per day ) this apparatus was 64- to 90 - pct effective in desiliconization with oxygen efficiencies of 19 to 41 pct . Detailed experiments to develop basic engineering data are underway , and adaptation of this principle to other reactions and reactants is planned .

Jan 1, 1964

By William Campbell

(Cleveland Meeting, October, 1912.) THE structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, it series of transition-products with distinctive structures, to which have ,been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school ; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-products-all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron-carbon diagram and the structures met with in hard- * Associate Professor of Metallurgy, Columbia University in the City of New York.

Dec 1, 1912

By A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate, while increasing it decreased the corrosion rate. Keywords: austenitic stainless steel, % ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentio-dynamic scans, microstructure, chemical analysis.

Jan 1, 2007

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

The following letter has been received from Professor P. A. Young, Head of the Department of Mining and Mineral Engineering at The University of Leeds, England. Extractive and process metallurgy The first annual TMS-AIME Extractive and Process Metallurgy Fall Meeting:1983 International Sulfide Smelting Symposium, will be held from 6th to 9th November, 1983, in San Francisco.

Jan 1, 1982

By Reinol Compañero, Ivy Gonzales, Herman Mendoza, Brian Buenaventura

"The extraction of gold in the Philippines has been a significant challenge for the past decades. Around 70-75% of gold mined in the country can be accounted from the small-scale mining industry which primarily use the traditional cyanidation and amalgamation; processes which have been advocated due to its adverse affects to health and environment. To address this challenge, an alternative clean and sustainable technology was developed for the small-scale miners to recover gold and other metal/mineral values efficiently from Philippine ores. An initial survey was conducted and followed through with extensive mineralogical investigations ascertain the best method applicable. It was determined that Philippine gold occur in ore as (1) very fine particles in the microns range, (2) free-milling, which is in abundance, and (3) locked particles with sulfides --- it was concluded that enhanced gravity concentration and flotation are viable alternatives. A comprehensive test regime was followed to check the response of the ores obtained from different small-scale mining districts across the country. It was shown conclusively that the gold ores respond positively, with recoveries using gravity concentration and flotation of at least 95% and 88%, respectively; exceeding the nominal recoveries using cyanidation or amalgamation. A specific process flow was designed for each type of ore with customized parameters. It was determined that while capital expenditure of implementing these alternative processes is higher than what is currently being used, the operational aspects show that it is much more economical to apply enhanced gravity and flotation. It should be noted that the process developed addresses the critical issue of environmental costs which should be more than enough to justify the shift from the current to the novel and sustainable technologies."

Jan 1, 2014

By M. J. van der Meulen

"The Netherlands has major resources of sand, gravel and clay, exploited mainly for construction works and the building materials industry. As in most western countries, mineral extraction meets with considerable societal resistance. To this end, Dutch minerals policy aims to prevent extraction by promoting economical use of materials, and the use of alternative (secondary or renewable) materials. Up till recently, it also included a system of production planning to sustain supplies of regionally scarce materials. Dutch policy development is reviewed and discussed in terms of pitfalls and possibilities for mineral planning in general. Promoting secondary substitution has been quite successful, and presents an example. In contrast, the production planning system has been controversial from the start and ineffective as a result, mainly because it attempted to solve supply problems without properly addressing the underlying resistance. For this reason the system is in the process of being abandoned. The full paper will be published in: Petterson, M., McEvoy F, & Marker, B.R. (Eds) 2005, Sustainable minerals operations in the developing world, Geol. Soc. Lond. Special report series, in press. This abstract is reprinted with kind permission of the publisher."

Jan 1, 2005

By Anthony T. C. Goh

"For deep excavations in soft clay, it is common to use jet grouting piles (JGP) prior to excavation to minimize wall deflections and ground settlement, and to prevent basal heave instability. In this paper, finite element analyses were carried out to assess the basal heave factor of safety for excavations in soft clay supported by JGP. Comparison of the factor of safety from the finite element analyses with limit equilibrium methods was then performed. Subsequently, to account for the uncertainties in the soil and JGP properties, a simplified reliability analysis procedure is proposed to estimate the probability of basal heave failure for deep excavations supported by JGP.INTRODUCTIONJet grout piles (JGP) are often used to prevent basal heave instability and to minimize excessive wall and ground movements associated with deep excavations in soft clay deposits (Shirlaw 2003; Wen 2005; Ou 2006). The jet grouting process which is carried out prior to any excavation works produces a series of short overlapping grout columns resulting in a “continuous” base slab (commonly termed as jet grout pile or JGP) below the final excavation level that spans across the entire excavation (Gaba 1990; Hsieh et al. 2003; Ho and Hu 2006). Typically, the JGP thickness ranges from 2 m to 4 m.The focus of this paper is on the assessment of basal heave instability for deep excavations in clay stabilized with JGP. Finite element analyses were first conducted to determine the basal heave factor of safety for deep excavations in clay with JGP. Comparisons were then carried out with factors of safety based on conventional limit equilibrium methods. Since the conventional factor of safety approach does not explicitly reflect the uncertainties of the soil and JGP properties, it is demonstrated in this paper that a simple reliability based approach (Hasofer and Lind 1974) can be used to assess the probability of basal heave failure.LIMIT EQUILIBRIUM METHODFor excavations is clay, the Terzaghi (1943), Bjerrum and Eide (1956) and Eide et al. (1972) methods which are based on bearing capacity theory, are commonly used to determine the basal heave factor of safety. Another commonly adopted method in Japan and Taiwan is the slip circle method which involves taking moments about the lowest strut level (JSA 1988; Hsieh et al. 2008; Luo et al. 2012). The slip circle method has also been applied for excavations with a JGP at the base by incorporating the undrained shear strength of the JGP. In the slip circle method, the basal heave factor of safety FSslip is assessed by taking moments about the lowest strut level (Fig. 1)"

Jan 1, 1900

By Jerry E. Olson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 20,071-acre South Fork Wilderness Study Area (OR-005-033) and part of the 8,791-acre Sand Hollow Wilderness Study Area (OR-005-034) in order to evaluate their identified mineral resources. The study areas are located in Crook County, OR, about 58 air miles east from Bend. The areas studied are underlain by Tertiary- and Quaternary-age volcanic and tuffaceous sedimentary rocks. No mineral resources were identified in or adjacent to the study area. Except for common opal and agate occurrences along the northern boundary of the study areas, no mines, prospects, or mineralized zones occur within the study areas. Bentonite is periodically mined less than 1 mi southwest of the Sand Hollow study area boundary. Neither of the study areas has geothermal leases, but both areas are under lease for oil and gas.

Jan 1, 1987

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor

Feb 1, 2020