Search Documents

By M. K. McCarter

Surface mining applies to extraction of mineral resources from water and sediments of rivers, lakes, seas, and oceans; from solutions circulating through broken rock and soil; and from rock and soil excavated from the earth. Surface mining is responsible for the majority of mineral production in the United States and a substantial portion of the world?s total production. This section deals specifically with extraction methods which employ mechanical processes in a relatively dry environment to free minerals from the earth. The following section, Section 15, deals exclusively with aqueous methods. With recognition of the importance of reclamation in all activities which temporarily disturb the earth?s ecosystems, it is appropriate to classify mechanical extraction methods as either deferred reclamation or concurrent reclamation. Deferred reclamation is necessary when the shape and logistics of the excavation require that it remain open throughout the productive life of he project. Upon exhaustion of economic reserves, the opening is then reclaimed in a manner consistent with public safety, environmental acceptability, and land use policy. Methods employing deferred reclamation are commonly referred to as open pit or quarry mining. Metallic ores, industrial minerals, and coal are all extracted using open pit methods. Typical examples are provided in Chapter 14.1.

Jan 1, 2008

By TvS. von Moltke

Steel is a highly versatile material due to its low cost and good mechanical properties, but typically needs some or other form of corrosion protection due to its tendency to corrode when exposed to atmospheric conditions. In the case of organic coatings, the corrosion protection and functionality of the final product is critically dependent on the adhesion of the coating to the surface of the steel. In this work the effect of contaminants and the nature of the surface layers present on industrial steel products are investigated by means of paint adhesion tests, Auger electron spectroscopy (AES), and X-ray Photoelectron spectroscopy (XPS). It was found that the presence of sodium species on the surface is very detrimental to paint adhesion under wet conditions, while satisfactory adhesion may be obtained even in the presence of silicon and carbon residues. It was also found that the nature of the Fe-O layer, formed under wet conditions is labile and different from that formed in dry air, and that subtle changes in process conditions, such as changing the oxygen content of the quench water, may change the adhesion of paint to the surface of the steel. Lewis acid-base interactions are discussed as a mechanism that may determine the bonding between the steel and polymer coating.

Jan 1, 2003

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company's Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976

By J. B. Morrow

BITUMINOUS COAL production for 1937 up to Nov. 27, was 400,000,000 ions, an increase of 3.43 per cent over the comparative period in 1936. The in- crease in consumption, however, was not so great as the increase in production. Stocks of coal, mostly in the hands of consumers, on Nov. 1 were 57,000,000 tons, compared to 44,400,000 tons at the same periods in 1936. The prospects were that both production and consumption for December, 1937, would be lower than for the corresponding month of 1936. , Anthracite production for the period ending Nov. 20 was 43,900,000 tons, com- pared to 48,500,000 tons for the corresponding period in 1936, or a decrease of 9.5 per cent. Production of mechanically loaded coal in. 1936 was approximately 57,000,000 tons, an increase of 17.5 per cent over

Jan 1, 1938

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By W. D. Striffler

Land disturbed by surface mining in Colorado and other western states has increased substantially over the past several years and is likely to increase even more in the future. This study was initiated to provide basic information on hydrologic and erosional characteristics of regraded coal spoils in Colorado as an aid for planning future reclamation activities. Eleven of twenty-one surface mines licensed in Colorado were sampled during the summer of 1980 and 1981. Mines not sampled included mines which had not progressed to the point that reclamation had begun, and mines where operators denied permission to sample. All coal regions were sampled with the exception of the San Juan Coal Field. Physical and hydrologic characteristics of regraded coal spoils in Colorado were determined using standard field and laboratory procedures. Field sampling included characterization of sites (slope, vegetation density, proportion of surface rock, bare soil, etc.) and infiltration measurements using a l-meter square drop former raining on a 1/2 square meter rectangular plot frame. Core samples collected in the field were analyzed for saturated hydraulic conductivity, bulk density, organic matter, moisture retention and texture. The erosion potential of each site was determined using the Universal Soil Loss Equation (USLE). Results of the sampling indicate that infiltration rates vary widely both within and between sites. However, definite trends with respect to coal fields are apparent. For example, the Green River (Yampa) coal region had a wide range of sampled infiltration rates (1.2 to 5.1 cm/hr). However, most of the sites clustered towards the low end of the range. The North Park (Marr Strip) also was rated at the low end of the infiltration range (2.0 to 3.0 cm/hr). Average infiltration rates for the Canon City and Uinta Coal Regions were at the high end of the range (4.9 to 5.5 cm/hr). Multiple correlation analysis of infiltration rates vs. site characteristics showed that infiltration rates were most closely correlated with the depth of wetting, the amount of mulch cover, and site slope. The depth of wetting was highly correlated with the depth of the topsoil and the bulk density of the spoil. In general, the topsoil at all sites appeared to be highly permeable to water intake but once saturated, subsequent infiltration depended upon characteristics of the underlying spoil. Vegetation cover affected infiltration on individual mine sites but was not as pronounced as topsoil characteristics or mulch. Erodibility of topsoil and spoils, as determined by Wischmeier's "K" factor, ranged from 1.34 to 0.56 tonnes/ha. (topsoil) and 1.25 to 0.66 tonnes/ha. (spoils). Definite trends in erodibility are evident. The Green River (Yampa) Coal Region displayed consistently higher erodibilities (1.34 to 0.75 tonnes/ha.) than other coal fields (0.72 to 0.56 tonnes/ha). Lowest erodibilities were observed in the Uinta, North Park, and Raton Mesa Coal Regions (0.56 to 0.62 tonnes/ha). Erodibilities of underlying spoils showed similar trends as the topsoils. Erosion potential (the product of soil erodibility and rainfall erosivity) was detennined using calculated ?K? factors and rainfall erosivities (R) taken from Clyde (1976). Results show that the Delagua coal field, Raton Mesa Coal Region had the greatest erosion potential due to the high rainfall energies in the region, while the North Park and Uinta Coal Regions had the lowest potential erosion.

Jan 1, 1981

By M. Didyk

The final objective of a mine ventilation project is to find a way of supplying the working faces with the necessary quantity of air to dilute all the possible air contaminants to safe limits and to maintain the temperature, humidity and oxygen content within desirable limits. To accomplish the aforesaid, decisions have to be made at early stages of planning and design of a mining operation. That is, ventilation and mine planning are closely related and interdependent, and experience has proved that improvisation as related to mine environment is rarely optimal in ventilation engineering. Mine management should be concerned with two general aspects of ventilation problems. The first is related to the statuatory requirements which are usually the minimum standards that have to be maintained. During the last two decades, mining laws have become increasingly stringent and management of operating mines had to face the effects of these externalities. In some cases these required either a production rate reduction or additional mine development. The second aspect that management should not overlook is the technical and economical importance of mine ventilation on the overall mining cost. In coal mining it is necessary to move, on an average, five tons of air through the mine for each ton of coal produced. The power cost incurred is perhaps the single most important direct cost assigned to ventilation but it is not the only one. Other costs that should be considered include the supervisory labor cost, fan depreciation and maintenance, doors, stoppings and regulators construction cost and maintenance, the additional mine airways development and maintenance because of ventilation requirements. That is,

Jan 1, 1977

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By A. B. Cecala

Video technology coupled with datalogging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. these techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties. the Helmet-Cam is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a datalogging dust monitor. these are worn by the miner in a backpack, safety belt or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data filesare downloaded to a computer and then merged together through a NIOSH-developed computer software program called enhanced Video Analysis of Dust exposure (eVADe). by providing synchronized playback of the merged video footage and dust exposure data, the eVADe software allows for the assessment and identificationof key work areas and processes, as well as work tasks that significantlyimpact a worker?s personal respirable dust exposure. the Helmet-Cam technology has been tested at a number of metal/nonmetal mining operations and has proven to be a valuable assessment tool. mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed eVADe software will be available for download at no cost on the NIOSH website.

Sep 1, 2013

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By Ramona Prillhofer

Salt slag is a waste product produced by the recycling of aluminum. In most European countries (e.g. Austria, Germany) the landfill disposal of this waste is forbidden because the slag contains soluble salts and these represent a potential source of pollution to the surface and groundwater. Additionally, consisting metal and some compounds in the salt slag can react with water and resulting from this, noxious gases are generated. The recovery of useful materials from these wastes is accordingly both environmentally necessary and economically feasible. This study describes a complete recycling-process for the salt slag, which includes a leaching-cristallization-process to obtain the oxidic residue, a pyrometallurgical-step to clear the oxidic residue and finally an extensive characterization of the achieved products. Due to the increasing price of raw materials, the utilization of the oxidic residue into commercial products has been investigated and application possibilities will be discussed.

Jan 1, 2009

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

By William R. Yernberg

The early part of the decade was marked by world-wide problems and economic difficulties. In 1980, President Jimmy Carter ordered the failed military mission to rescue hostages in the U.S. Embassy in Iran, Mt. Saint Helens, WA erupted killing 60 people and the Soviets and Mujaheddin guerrillas clashed in Afghanistan after the Soviet invasion. Later in the year, Ronald Reagan was elected president, defeating Carter. The first launch of a space shuttle (Columbia) occurred in 1981. Also in 1981, the first IBM-PC’s begin to roll off the lines. In 1982, Argentina invaded the Falkland Islands and Mexico’s economy was in collapse. In 1980, the U.S. unemployment rate stood at 7.1 percent, and by 1982 the rate increased to 9.7 percent. 1980 marked SME’s first full year in its new office building in Littleton, CO. The new facility was dedicated in November 1979. Claude L. Crowley was executive director of SME in 1980 and remained in that position throughout the decade. SME’s membership stood at about 26,000 throughout this period (1980-1982).

Jan 1, 2007

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By M. C. Malamphy

The report of work accomplished on the United States Bureau of Mines' bauxite project in Pulaski and Saline Counties, Ark., is presented in this volume and in a series of Reports of Investigations immediately following this volume. This first volume covers the project as a whole, whereas the subsequent volumes contain maps of local areas and deposits developed, together with logs of the drill holes and descriptions of the separate deposits. The Arkansas bauxite project was initiated in December 1941 and continued for 4 years. The first 5 months were spent in studying the problems presented and in geophysical exploration, Core drilling began in May 1942 and ended in May 1945. The project was one of the larger and more important of those undertaken by the Bureau of Mines for the purpose of developing domestic sources of supply of critical and strategic minerals necessary for National defense and for the successful waging of modern mechanized warfare. Some of the results of the Bureau's bauxite exploratory work have been made available to the public through the medium of press releases, transactions of technical societies, and government publications. More information has been supplied to government agencies upon request and to land owners and mine operators of the deposits concerned in the form of maps showing locations of all holes drilled on the property and logs with chemical analyses of' all cores recovered. In October 1946, the factual data were made avail-able to .the public in manuscript form in an-"open file" at the office of the State geologist, R. B. Foxhall, Little Rock, Ark., and at the office of the. Bureau of Mines in Washington. For the purpose of providing a background for the presentation of the factual data obtained, the history of bauxite is reviewed briefly. Information relative to past production and reserves of bauxite in Arkansas also is given. A resume of the development of the industry in Arkansas, the exploration and mining methods employed, the various uses to which the bauxite is put, and a brief outline of the geology of bauxite in Arkansas complete the -background.

Jan 1, 1948

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By Vincent Roy

Numerous on going activities at the Daniel-Johnson Dam : ? Surveillance / monitoring ; ? Structural investigations & evaluation ; ? Injection work ; ? Crack mapping ; ? Instrumentation management (drawings & inventory) ; ? Drainage system state ; ? Foundation evaluation

Aug 1, 2013

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929