Search Documents

By I. A. Kovalevska

Considered problems: elaboration and implementation of resource-saving technologies, low-cost support systems improvement, openings security and support, based on wallrock condition control with supreme implication into the rock pressure occurrence counteraction work. Results of analytic and underground investigations using computer simulation of the finite elements in order to calculate stressstrain state of the multivariable geomechanical systems are presented. Solutions of concrete objectives are found using spatial geomechanical model of solid motion around openings, considering real geomechanical parameters formation of support forms with proper conditions of their contact and real mechanical characteristics. Ultimate solutions of resource-saving technologies implementation based on the analysis of multivariate vertical, horizontal, and reduced stresses components calculation and also near-contour rock, support bearing components and security constructions movements are found. Results of experimental investigations of combined supports and security constructions, which increase openings' stability in difficult conditions of flat coal seams are presented.

Aug 1, 2013

By Jean-Louis Briaud

The following is a summary of a very recent report prepared at Texas A&M University for the National Cooperative Highway Research Program and entitled "Downdrag on Bitumen Coated Piles". Anytime the soil settles more than the pile, downdrag or negative skin friction will develop. The load in the pile increases with depth up to a certain point and then decreases down to the pile point. This phenomenon has been quoted as being the number one culprit for deep foundation failures. In Chapter 1, an introduction to downdrag is given. The most common criterion for downdrag is to consider it in design as soon as the settlement of the soil surface after pile driving exceeds 0.5 in. Coating piles with bitumen is an effective way of reducing downdrag forces and therefore allows to use smaller piles for the same load. This results in cost savings. Coating piles with bitumen increase the cost of piles by about 33% and therefore the decision to use bitumen is generally based on economic considerations.

Jan 1, 1989

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By M. Ge

Signal processing is a major challenge for In-Seam Seismic (ISS) technique. Fourier Transform is an important tool for signal processing such as frequency analysis. However, for ISS signal, localized information, especially time-frequency localization is even more important. Wavelet Transform (WT) provides another approach to study the signal as a function of frequency and time. The objective of this paper is to demonstrate the application and advantages of WT to seismic signal analysis. Both transmission and reflection signals from coal mine void detection experiments are analyzed. The results illustrate that WT appears to be a powerful and convenient method for the in-seam seismic signal processing.

Jan 1, 2007

By W. G. Brissenden

"ALTHOUGH I SHOULD FIRST REVIEW the state of the mining art as it is today, because of the shortness of time I will confine myself to a re-view of the more important advances in that art which have been made in the past two to three decades. Then, a look at the opportunities and the challenges which now present themselves will be more meaningfulFirst, some of the more impor-tant developments in underground mining:(1) The recognition that good ventilation, visibility and working conditions are essential preliminaries to efficient production has resulted in their incorporation as a matter of practice in modern mine planning. (2) The introduction of the car-bide bit and the re-introduction of the airleg drill, and the resulting sharp rise in productivity, were early postwar developments. (3) The recovery of the coarser fraction of mill tailings for use as mine backfill also is an important cost-reducing development of recent years -and this has led to cemented backfill, which, al-though more expensive, meets certain specific needs and has tremendous potential. (4) Great strides have been made in improving explosives' materials and explosives' accessories. Millisecond-delay electric blasting caps, which improve fragmentation and reduce the seismic effect of blasting, and the development and •application for underground use of explosives are but two among many such improvements. (5) Trackless mining methods, using quarry-type equipment in some instances and specially de-signed low-headroom trucks, loaders and carrier-mounted drills in others have been successfully applied. (6) Dual-purpose load-haul units are now in use loading and hauling from open stope drawpoints, and smaller versions of this type of unit are in use in cut-and-fill and other types of stopes."

Jan 1, 1968

By M. E. Huckman

In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the colunm, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nernst-Planck equation as the constitutive equation for diffusive flux We use a Nernst-Planck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model? The data from this comparison suggests that the Nemst-Planck type model yields better results.

Jan 1, 1996

By Tom Gabardi, Peter Clarke

"MillMapperTM is a new 3D laser scanning technology that has only recently been introduced into the North American mining industry. It enables mill operators to gain a much more complete understanding of the condition of their mill internals and to more accurately predict how liners will perform in the future. This paper describes the technology and techniques used to obtain data on internal mill conditions, how this data is processed into meaningful information which enables better prediction of liner life and gives examples of the reports provided by the software. Examples are given, using client sites data, on how this information is being used to reduce the costs and improve the revenue from SAG and ball mills.INTRODUCTION Scanalyse Pty Ltd developed the MillMapperTM technology in Australia over a number of years and has recently introduced it into North America with a significant take-up in Canada. The technology was commercially released in Australia in late 2006 and there has been significant technical development in the features provided since that time. MillMapperTM has been accepted as a useful technology in the Australasian region and more recently has been introduced to sites in Chile, Peru, Brazil, USA, Canada, Laos and South Africa. Over 100 different mills have been scanned and the technology has been thoroughly tested and validated. It has become an integral tool in condition monitoring and improvement programs for SAG and Ball mills across many sites and is now providing significant and measurable benefits to the mining industry. Some of these benefits will be described in this paper using actual examples."

Jan 1, 2012

By B Leisemann, M Watkinson

Coal augering is an ideal method for recovering coal from the highwalls of open cut coalmines. Coal augering is a simple process whereby additional flights are added to the auger cutting head and auger holes are drilled at 1.9 m diameter up to 200 metres deep. Traditional monitoring was located at the mouth of the hole and if methane was encountered above two per cent, inert gas was delivered into the mouth of the hole to deplete the oxygen content at the auger cutting head below 12 per cent. The auger operator was asked the question ‘how do you know that this is the case?’ Trials were undertaken to prove that the oxygen content at the cutting head did drop below 12 per cent (the lowest limit for methane to ignite, also known as the oxygen nose point). Initial trials showed that the oxygen content in the mouth of the hole did not drop below 12 per cent and modifications were made to hold the inert gases in the mouth of the hole so that the auger flights could take this inert gas into the hole. In-hole monitoring, after completion of mining and after extracting the auger flights, showed that the atmosphere quickly returned to fresh air. In-hole monitoring was also tried during the augering process and yielded valuable results. This paper will discuss the results of the monitoring, information on the gas results obtained and the methodologies used to optimise the oxygen content at the auger face.CITATION:Watkinson, M and Leisemann, B, 2017. Inertisation of coal augering holes, in Proceedings Australian Mine Vent Conference 2017, pp 293–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By L Mariano

Three selected iron ore samples from the major bedded and channel iron deposits of Western Australia were analysed using a scratch test commonly used in the oil and gas industry. The portable commercial equipment dubbed Wombat cuts a groove on the surface of the sample with a cutter under imposed depth of cut and cutting velocity. The normal and tangential components of the force acting on the cutter are recorded with a high degree of precision (about 1N) at fine spatial resolution of about 20 measurements per millimeter.The intrinsic specific energy inferred from the scratch test measurements is found very well correlated with a classical measure of strength such as the uniaxial compressive strength, for over 300 sedimentary rock samples.The results obtained on the iron ore samples are comparable to those obtained on oil and gas sedimentary rocks. This method could provide an objective and semi-automated measurement of material strength and brittleness in iron ores that can possibly be correlated to the lump to fines ratio.

Jul 11, 2011

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in these two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number.-of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section I of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the antitrust laws is entitled to recover treble damages plus costs.

Jan 1, 1965

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By S. T. Johansen, C. Colomb, B. Ravary

Combustion and thermal NOx formation have been modelled using the Computational Fluid Dynamics (CFD) commercial code Fluent 6.1. The aim was to predict and give a better understanding of the combustion in electric arc furnaces for the production of ferro-silicon and silicon metal. Another important objective was to assess the impact of a number of operating parameters on the NOx formation. The CFD tools used are de-scribed with a special focus on models for species and turbulence transport. Sensitivity studies have been carried out to study the influence of several parameters: sub-models, process gas composition and distribution at the charge surface and influence of the presence of SiO. The main conclusions are: ?Using the combination of a realistic design, boundary conditions and models, the simulated NOx level is in quantitative agreement with measurements. The presence of water vapor is particularly important because of its influence on the specific heat of the mixture and resulting temperature. ?Release of significant amounts of SiO from the charge surface results in an important increase of NOx, even if we applied a simplified combustion model for SiO gas. However, because of lack of thermal and compositional data for blowing situations (when SiO flows directly from the arc cavity through open channels to the charge surface), no quantitative validation is possible. The way SiO is distributed (uniformly or as a jet) has a limited impact on the result in our computations.

Jan 1, 2007

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By R. Larry Grayson, Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Feb 24, 1997

This evening I intend to explain the position of the gold mining industry in the light of post war trends and events.I propose initially to comment on gold production throughout the World and then proceed to the state of the industry in Australia, with an account of the efforts made within the industry to maintain levels of production. This will be followed hy a statement on assistance granted to the industry by Federal and State Governments.Annual World gold production is estimated at 51,000,060 fine ounces, made up as followsSouth Africa - 27,300,000 fine ouncesCanada 4,200,000 &quot; &quot;U.S.A. 1,500,000 &quot; &quot;Australia - 1,000,000 &quot; &quot; Others 5,000,000 &quot; &quot;----- 39,000,000 &quot; &quot;Estimated Russianproduction - 12,000,000 &quot; &quot;Total 51,000,000 &quot; &quot;The opening up of new highly payable mines during the post war years has contributed to the preponderence of production in South Africa.In 1962 some 24 new mines produced 73 per cent of South Africa&apos;s gold, and contributed almost 90 per cent to the industrial profits.At the same time, 20 old mines were struggling to main...

Jan 1, 1964