Search Documents

By G Metzner, R Rodriguez, C Savage

OK Tedi Mining Ltd. (OTML) is in the process of optimising the concentrator performance. One aspect that has been recently implemented is an upgrade of the existing expert control philosophy on the grinding circuit and this will be the topic of this paper. Ore grinding in SAG mills is a multi-input multi-output (MIMO) process subject to several disturbances, most typical being quick acting disturbances such as changes in ore characteristics like hardness and particle size and slow acting disturbances such as ball charge variations and liner wear. The OTML SAG mills treat ore from diverse ore bodies and receive fresh feed subject to large changes in particle size. These circumstances make these mills particularly challenging to control. In this paper, a comparative analysis is presented between the performance of the OTML SAG mill #2 before and after the commissioning of a hybrid control strategy. The strategy uses Expert Knowledge combined with advanced disturbance rejection to reduce the variability of the main process variables, especially pressure and power. It further optimises the overall operation by driving the SAG mill #2 against process constraints (e.g. high power, high motor temperature and high scats recycle rate) and maintaining the operation at or near this point. This strategy is implemented by a combination of the manipulated variables (i.e. fresh feed tonnage and % solids) at any given time.The paper will present trends and a statistical analysis of the comparative results of the mill operation over a period of months, showing a 30% reduction in mill power / pressure variability and a 12% improvement in average power drawn. An increase in throughput was also observed, but cannot be conclusively attributed to the change in mill control due to other changes that were made to the SAG mill #2 during the period of comparison. An additional benefit includes better acceptance from the operators with improved consistency of the SAG mill #2 operation across shifts.The paper will also discuss further improvements envisaged in the continued optimisation of the grinding control circuit.CITATION:Savage, C, Rodriguez, R and Metzner, G, 2013. Hybrid process control strategy for the Ok Tedi Mining Ltd semi-autogenous grinding mill #2 - A comparative analysis, in Proceedings MetPlant 2013 , pp 202-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Chee Theng

"Getting minerals out of ores is messy, but mineral processors learn to have fun with it. Celebrating the innate joys of the industry was the theme of this year’s Colorado MPD Conference. At the same time, attendees dug deeper for insights into problems that continue to dog the community, including tailings dam crises, water resource challenges, and a dwindling number of academics to teach and train the workforce (see box).Tailings dam crisesMatt Fuller of Tierra Group International Ltd. brought some of the audience to tears with his impassioned talk on “The Infamous Legacy of Upstream Tailings Dams,” which won the conference’s Lou Cope award for best paper. The talk was especially poignant coming on the heels of the January tailings dam failure in Vale S.A.’s Córrego do Feijão iron ore mine in Brazil, the latest in a series of catastrophic dam failures over the past decade that includes the Fundão dam failure in 2015.Noting that the two dams share a common characteristic — both are upstream tailing dams — Fuller explained the three basic dam construction methods and why certain upstream tailing dams are susceptible to failure (Fig. 1). The downstream, centerline and upstream methods denote the direction the centerline of the dam crest moves with each successive raise in elevation of the dam. With the downstream dam, the foundation for future raises is essentially the same as that of the starter dam, he explained. With the centerline dam, half of the dam is constructed on the same foundation as the starter dam, and with the upstream dam, each successive raise is built out over the top of the tailings.“Downstream dams are expensive to build because each successive raise is bigger, so the sustaining capex to build them keeps growing,” Fuller said. Many decades ago, mine owners realized they could construct a starter dam, put their tailings through a hydrocyclone, generate a coarse sand fraction and stack the sand over the top of the tailings to build the next raise. “Then, there is no sustaining capex, it all comes out of operations,” Fuller added. The footprint is smaller, and it is a favorable means of retaining the tailings."

Jul 1, 2019

By S. A. Scott

Mintek developed the MinataurTM leach-solvent extraction-precipitation technology as a cost effective, easily operated alternative to conventional gold refining processes. The technology was first commercialized at the Harmony Gold Refinery in 1997 to produce 99.99 per cent gold product and has subsequently led to development of various value-addition steps including the casting of various investment bars, gold wire drawing and gold potassium cyanide powder production. In addition to refining gold to high purity, if an appreciable amount of silver is present in the feed material it is also refined to 99.99 per cent purity. The major advantage that the Minataur? technology has over other gold refining processes is the relatively low gold lock-up and reduced operating costs. The operating cost1as at April 2001 for the expanded Harmony refinery (24-ton per annum gold production) was approximately half that of conventional smelting and toll refining. The extractant employed for solvent extraction is relatively cheap and highly selective for gold, making the technology attractive in situations where significant quantities of platinum group metals or base metals are present.

Jan 1, 2004

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

By S Thomson, M Lovitt, T Purvis, C te Kloot, T Nguyen, Z Liu

Ernest Henry Mine (EHM), located in north-western Queensland, is an underground copper/gold sublevel caving operation currently producing over 6 Mt/a of ore. The mass mining method of sublevel caving (SLC) used at EHM involves systematically blasting a series of uphole rings in parallel ore drives and drawing the broken ore using a top-down approach. Each ore drive contains multiple precharged rings to prevent having to charge in close proximity to the brow of the previously fired ring; however, the current initiation system still involves ‘hooking up’ all detonator lead cords of the first precharged ring. The unstable nature of a rill and working close to a brow presents hazards to personnel completing the hook-up process. There is also a business risk of ore loss when damaged ground support completely prevents access to the next precharged ring. If the hook-up step could be eliminated, the risk to personnel and the business would be significantly reduced.EHM engaged Orica Mining Services in 2016 to trial their WebGenTM 100 – wireless electronic blasting system (WEBSTM) for the first time in an underground mining environment. Having successfully signal-tested the equipment, two test holes were initiated, followed by a single production ring and then multiple production rings. In total, 30 production rings were successfully fired underground at EHM in 2017. To do this, WEBSTM was successfully integrated into EHM’s current charging and firing process, resulting in no business delays or loss to production. None of the 30 rings required hooking up and all were initiated from the surface with no personnel underground. A high level of ownership from all personnel involved ensured the trial was a success, and provided scope for wireless detonators to be used successfully on a large scale – both at EHM and other sublevel caving operations. WEBSTM is now a proven example of technology that can be used to improve safety in the mining industry, through eliminating the need for personnel to work in hazardous areas.CITATION:te Kloot, C, Liu, Z, Purvis, T, Thomson, S, Lovitt, M and Nguyen, T, 2017. Improving safety through technology – Orica wireless electronic blasting system trials at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By W. A. Calhoun

A method for treating high-iron Arkansas bauxites for recovering both abrasive and metal-grade bauxite has been developed by the Bureau of Mines. Present practice usually produces a reject containing appreciable quantities of metal-grade bauxite; however, the processing renders the alumina in the reject unsuitable for the Bayer extraction treatment. Thus the Arkansas abrasive bauxite industry has, in the past, produced little or no metal-grade bauxite. The present investigation was made to determine the possibilities of batter utilization of those particular bauxites through recovery of the wasted metal-grade portion. The large expansion of aluminum-production facilities planned for 1951-53 makes recovery of metal-grade bauxite from presently treated abrasive and marginal abrasive ores en especially timely objective and a welcome addition to our aluminum potential. The quality of the Arkansas bauxites and the inherently associated titania content have made this material particularly attractive to the abrasives industry. however, the gradual depletion of natural abrasive-grade bauxite reserves in this area, the comparative scarcity of high-grade ore, and the difficulty of maintaining adequate reserves have necessitated blending different grades of bauxite calculated to meet specifications. Production of abrasive-grade bauxite from tile, high-iron reserves 13 becoming, increasingly necessary. In one commercial operation, producing abrasive-grade from ores averaging slightly less than 10 percent Fe2O3, approximately 2.7 tons of ore are required to produce 1 ton of abrasive-grade bauxite. The reserves of ore of this grade, however, have been considered inadequate for a long-range production, and ultimately ores averaging 12 to 15 percent Fe2O3 will have to be treated to moot the continued demands of the abrasive industry.

Jan 1, 1952

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By Bertil I. Pålsson

The most common REE containing mineral that is worked today is bastnäsite. It means that mineral processes are adapted to it and that the metallurgical separation techniques for winning of individual REE are adapted to bastnäsite concentrates. For all other deposit types, suitable mineral processing methods and separation technologies need to be adapted and/or developed. Preliminary mineralogical analyses indicate that slightly less than half of the REE in the tailings dumps at LKAB/Kiruna are associated to apatite. The rest is in the minerals monazite (maybe associated to apatite) and allanite. At least allanite is probably not floatable with reagents commonly used for apatite. Mass and element distributions for the tailings sand reveal that very little apatite is present above 300 µm, and that approx. 30 % is below 20 µm. REE does not follow P2O5 completely and are also present in coarser fractions. Flotation results show that the best condition for both apatite and REE winning is pH 9, high collector addition and low dosage of water glass. Under these conditions, the lab-scale flotation gives an apatite concentrate with at least 30 % P2O5 at 70 % recovery. REE follows apatite in the cleaner steps but only partly. Its recovery is approx. half compared with apatite. The reason for the low REE recovery is likely to be that REE to a large extent is trapped in non-winnable minerals, especially allanite. The REE grades in the concentrate are expected to be in the range 3000 ? 4500 g/ton. Keywords: flotation, REE, apatite, monazite, allanite

Sep 1, 2012

By Don Welch

Pressures for change ?Land use constraints ?Project financing ?Local communities ?Environmental issues ?Sustainability requirements ?Stricter regulatory procedures ?Technical excellence ?Reduce risk ?Impacts of failure & non-compliance

May 1, 2010

By Yehia M. Youssef, Nourhan Moukhtar, M. H. Abdel-Aziz, Ibrahim Hassan

Copper was recovered from copper sulfate solution in a batch-recycled galvanic reactor operated under forced convection with the generation of electrical energy during the cementation process. The divided galvanic cell consisted of parallel copper and zinc plates. The mass transfer rate and the amount of electrical energy generated were found to be directly proportional to the solution flow rate and the initial concentration of metallic ions and inversely proportional to the distance between electrodes. The experimental results were expressed in terms of a dimensionless correlation including all parameters. The wastewater treatment presented herein cell can be utilized to recover many soluble heavy metal ions from solution with high efficiency.

Oct 2, 2020

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005