Search Documents

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

The value of raw nonfuel mineral materials production totaled an estimated $19.7 billion in 1978. The record 1978 value exceeded by 13 percent the 1977 value of $17.5 billion. This raw mineral output was the basis for approximately $200 billion worth of processed materials of mineral origin. Output of both metals and nonmetals increased about $1 billion each, above comparable figures for 1977. Of the 22 metals produced quantitative output of 11 increased and the value of 13 increased. Among the 48 nonmetallic commodities produced, the quantities for 35 increased, and the values for 40 increased.

Jan 1, 1979

By E. G. Kearnery

Introduction It is believed that the present paper will be of some interest, not because of any outstanding features of Renabie milling practice but because Renabie is the first gold mining property in a newly explored area - in Leeson and Rennie townships, Sudbury district, Ontario - to reach the production stage. The Renabie mill was originally designed by the General Engineering Company (Canada), Limited, as a 300-ton plant and went into operation in June, 1947, treating an average of only 128 tons a day for the balance of that year. Toward the end of 1948 the capacity of the plant was expanded to 450 tons a day, and the tonnage treated was gradually increased from the 1947 figure to the point where 420 tons a day was averaged for the first nine months of 1949. Description of Ore In general, the outstanding gangue component of Renabie ore is white quartz, which comprises at least 80 per cent of its total bulk and in some sections considerably more. Virtually all the gold occurs in very finely divided state; only very rarely has free gold coarser than 325 mesh been observed. The ore has a very low sulphide content, ranging from about 0.50 to 1.00 per cent by weight. The gold occurs both free in the gangue and ? locked in sulphides, the proportion of one to the other varying considerably from one orebody to the other. Pyrite is by far the most abundant sulphide, followed by galena, which, however, appears to be entirely absent in some of the orebodies. Minor amounts of pyrrhotite, chalcopyrite, chalcocite, and sphalerite have been noted. The ore appears to be entirely free, or almost so, of minerals containing arsenic, antimony, or molybdenum, and in general it could be described as free milling. The various hindrances to extraction of the gold which have been met with are believed to be due largely to the very finely divided state of the metal and to its intimate association with the sulphides and gangue. The ore contains silver, with the gold-silver ratio about 3:1.

Jan 1, 1950

By Jerry C. Tien

In 2009 China mined 2.695 billion metric tones (Gt) of raw coal. It is estimated that only 3-5% or roughly 135 million metric tones (Mt) of these were mined from 300 some surface operations. Except for a dozen or so large modern operations, most of China's surface coal operations are small by western standards, with annual production ranging from a few thousand tones to 300,000 metric tones (mt). Depending on the size of operations, equipment used range from small trucks and shovels to large bucket wheel excavators and draglines in sizable pits. This article provides a brief overview of China's surface mineable coal reserves, mining methods commonly used and increasing environmental concerns; introductions of several large surface operations are also provided.

Jan 1, 2012

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By S. James Campbell

Ladies and Gentlemen: Never in the history of our mining industry has the emphasis on public relations been accelerated as much as it has in the last few years. Knowing of your keen interest in this subject I consider it a great privilege that your program committee has asked me here to discuss the crushed stone segment of our industry approach to this important part of our daily business lives. As you are aware, crushed stone operations are present in almost every segment of the country wherever aggregates for construction projects are required. The tonnage of crushed stone produced is second only to sand and gravel - another source of aggregates - and this together with sand and gravel amounts to over half of the tonnage of all mined products in the United States. What is unique about this industry that will be of interest to all of you in analyzing how they have approached Public Relations? The fact that it is so wide-spread is of course obvious, but perhaps a more significant nature of this segment of the mining industry that has brought it more in the limelight of public interest and on a larger scale is the location of a large part of the quarries quite close into the urban area and population centers where you have the greatest demand for aggregate products.

Jan 1, 1969

A symposium was held on January 30 and 31, 1973, at Pittsburgh, Pa., to review the state-of-the-art in designing and utilizing diesel-powered equipment in underground mining. The Health and Safety Activity of the Bureau of Mines sponsored the symposium with major assistance from the following four participating organizations: The American Mining Congress J. Allen Overton, President The United Mine Workers of America Arnold R. Miller, President The National Independent Coal Operator's Association Cloyd D. McDowell, President The Bituminous Coal Operators' Association, Inc. Guy Farmer, President Seventeen papers were presented during four half-day sessions devoted to the general subjects of the diesel engine, the place of the diesel in underground mining, health protection using diesels underground, and maintaining safety of diesels underground. Eleven of the speakers were from industrial organizations here and abroad; one represented the Provincial Government of Nova Scotia; two were with the Department of Health, Education, and Welfare; and three reported on Bureau of Mines work related to diesels.

Jan 1, 1975

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth's crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

VOLUME III The objective of Volume III of this report is to provide a concise review of six major types of legal constraints, controls, and regulations on surface coal mining in the United States, as of January, 1976. At the same time, an attempt is made to format the details of federal and state exploration, mining, and reclamation regulations such that point-by-point comparisons can be made and updated as revisions occur. Thus, Volume III should provide both an executive overview and a user's manual of legal controls of surface coal mining.

Jan 1, 1976

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By Malcolm D. Flavel

Much has been said and written about the world's, and particularly the united states of America's, energy crisis. The relative changes between cost components of production have altered because the days of cheap energy have now gone. Decisions that made capital investment reduction attractive to treat large tonnage lower grade ore bodies appear to be no longer valid because average energy costs for comminution that were less than 1 cent per kilowatt hour in 1972, are now more than 3 cents and will shortly become 6 cents according to some projections. Increased capital investment to improve processing energy efficiencies are certainly going to be pursued. Energy today is the largest cost component in the average mineral production facility. It takes more than 12000 kilowatt hours to produce one ton of finished steel and more than 60000 kilowatt hours for each ton of copper and aluminum.

Jan 1, 1980

The Interior Department's Bureau of Mines is the Federal Government's primary research arm in the mineral and fossil-fuel fields. In accordance with its Organic Act of 1910, the Bureau's responsibilities have been reinforced since the passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966, the Federal Coal Mine Health and Safety Act of 1969, and the Mining and Minerals Policy Act of 1970. The 1966 and 1969 acts deal specifically with the development of safe working conditions and a healthful working environment for those engaged in the mining industry, while the third sets the national policy as follows: " ... to foster and encourage private enterprise in (l) the development of economically sound and stable domestic mining, minerals, metal, and mineral reclamation industries; (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial security, and environmental needs; (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral resources, and (4) the study and development of [ ]

Jan 1, 1972

By Jr. Kermit Allen

A study was conducted for the AEC to determine the feasibility of constructing an unsupported 315 foot diameter spherical cavity at a depth of 2,700 feet in a salt dome. A cavity of this size and shape has never been attempted. It was determined that the three basic essentials for solution mining; adequate salt, fresh water, and a means of brine disposal were available at the Tatum Salt Dome in Lamar County, Mississippi. Assuming a large, unsupported mined opening of the size and at the depth required would remain stable, the most practical method of providing the cavity using solution mining techniques is by use of a movable blanket of air to control the water level to properly shape the cavity while removing the insolubles either with jetting or by conventional mining methods. It is estimated that, using the jetting method of insolubles removal, the cavity can be constructed in 24 months for approximately $7 million. Using conventional mining techniques to remove the insolubles and shape the final cavity, it is estimated that the cavity can be constructed in 36 months for approximately $12.6 million.

Jan 1, 1968

"Guests and Members of the Rocky Mountain Coal Mining Institute: "It gives me a great deal of pleasure to call the Fifty-Second regular meeting to order this morning. "I think that you will agree with me that we have an excellent program planned for the next three days, comprising various interesting and educational subjects by authors of prominence, which will be of keen interest to all of us in the coal industry. "The Program Committee, chairmanned by John Peperakis, has done an excellent job in securing this very splendid talent for our convention. "I would like to say a word as to the, condition of the coal industry in our part of the country as well as elsewhere. I believe we can look at it with more optimism than in the past several years, particularly in the state of Colorado, with which I am more familiar. "Annual coal production in Colorado gradually dropped from around 12 million tons during the years of World War I to as low as 8 million tons during the last war, and to less than 3 million tons in the year of 1954. We believe that it touched bottom that year, as in 1955 the state production went up again to nearly 3,400,000 tons, equivalent to an increase of 15%. As you know, the national increase in bituminous coal production for the year of 1955 was roughly 2000 over 1954. "The national increase for the first two months of 1956 over the same period of 1955 is approximately 2100. Colorado's production is running around 1000 over the comparable period of last year, and the 5 states represented by our Institute came up with a nice increase in 1955 over 1954 of 1000. "Figures on the increase so, far in 1956 for this group of states are not readily available, but I fully believe that. our industry locally, as well as nationally, is now starting out on a steady rise despite the fanfare of nuclear energy and its more glamorous competitor, solar energy. Many authorities tell us that real competition from these sources is a long way off and that the atomic energy program will consume far more coal than is displaced by nuclear power. "I do not mean to infer that we coal people are out of the woods by a long way' so far as holding and regaining markets, for our coal. The captive operators, which are well represented here, have not lost their market for coking coal, since coke is still a necessary

Jan 1, 1956

By R. S. Dean

This is the fourth of a series; of annual report of the Metallurgical Division to be released in this form and cover the fiscal year July 1, 1937, to rune 30, 1938. This report is not merely a recitation or brief of the year's work; it contains technical information in usable form, although a some of this has appeared or will he issued in greater detail in separate reports. The table of contents that follows fists the principal investigations accomplished and those that are being continued. Other projects are being begun and contemplated for the next year.

Jan 1, 1938

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSS systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981