Search Documents

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By Steven M. Rupprecht

"The artisanal mining sector in Central Africa is largely informal, yet provides an essential livelihood for many (directly or indirectly) participants, as well as facilitating an important source for the flow of income into many communities. Artisanal mining varies from site to site, but appear largely well structured despite its informality. The artisanal mining sites in Central Africa have some inherent management structure and the extraction itself is often organised. Artisanal mining is labour intensive and is generally conducted utilising hand digging methods e.g. shovels or hand chisels. Artisanal mining is generally more dangerous than small-scale or large-scale modern mining operations. This is especially true as artisanal operations are generally subsistence activities with artisanal miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. The objective, through proper/dedicated training of artisanal miners is to migrate Artisanal mining to establish a small-scale mining (SSM) industry in Central Africa. Through developing the necessary skills in the fundamental areas of mining it is proposed that Artisanal Mining can become more productive and safer mining operations. The paper reviews the above focus areas, highlighting the skills and tools that are necessary to assist in establishing a sustainable small scale mining industry migrating from manual labour to semi-mechanised mining and processing. The purpose of the transformation process is to create a safe, healthy, environmental and community oriented mining operation with the objective to uplift the skills and wealth of the mineworkers and the general community."

Jan 1, 2015

By Virgil W. Carmichael

In the Fort Union formation of western North Dakota, eastern Montana and northeastern Wyoming there are immense tonnages of lignite and subbituminous coal that have not yet been evaluated in terms of present economic conditions. The general lack of detailed geologic and topographic maps of this region, coupled with a considerable interest in some of its deposits, has spurred the North American Coal Corp. to develop a rapid, economical method of producing its own maps on which to base a quantitative evaluation of the coal reserves involved. The techniques the company employs in this mapping and evaluation program are simple photogeologic and photogrammetric procedures that can also be applied to other exploration and mining work. The air photos, in addition to being used for photogeologic interpretation, have been successfully applied to locating drainage cuts, haul roads, and road metal deposits as well as for various property studies and general mine and reclamation planning. The present discussion will deal primarily with North American's photogeological reconnaissance method of mapping and evaluating relatively flat- lying to shallow-dipping coal beds with limited topographic control and a minimum of core drilling. The field tools employed under this method include aerial photographs and pocket stereoscopes, engineering levels, aneroid barometers, portable transceiver radios and core drills. Field information developed on the photos is transferred to maps for measurement of reserves and overburden. To date this method has been used to map and analyze nearly 6 billion tons of Fort Union lignite and subbituminous coal.

Jan 8, 1969

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By J. A. Herrick

Jan 1, 1879

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

By Lynn L. Rethi

This U.S. Bureau of Mines report summarizes common obstacles found when attempting to implement health and safety strategies in small mines and small businesses in general industry. Recently, the U.S. Mine Safety and Health Administration focused much of its attention on addressing health and safety issues at small mines. Some of the more innovative interventions practiced by small businesses in general industry are discussed for consideration of their applicability to the mining industry. The most effective intervention strategy that was developed for small businesses is the Occupational Safety and Health Administration Consultative Program. The details of this program and other intervention strategies used by small mines and small businesses are presented.

Jan 1, 1995

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By RALPH HAYES SWEETSER

IRON ore and bituminous coal are the two basic raw materials for the whole iron and steel industry. The ore furnishes the iron and is absolutely necessary-all iron and steel products come directly or in- directly from the iron ores. The bituminous coal furnishes the carbon needed for the smelting of the ores and for the fuel used in all the processes of iron and steel manufacture. The necessary carbon could be furnished in some other form besides bituminous coal. In fact, it is only since the Civil War that bituminous coal has been the chief source of the carbon for metallurgical fuel. For many years only charcoal made from the forests furnished the carbon for smelting iron ores. About 90 years ago, anthracite coal was first used as blast-furnace fuel and for many years continued to be the chief blast furnace and steel making source for carbon. Even in my own blast-furnace experience, I have used charcoal in Canada and anthracite in Pennsylvania for smelting ores in an iron blast furnace. Bituminous coal, now almost exclusively the source for the carbon used in smelting iron ores, also furnishes most of the heat used in the steel-making processes. It is seldom used in blast furnaces in its natural condition, hut is first coked in beehive, or in by-product coke ovens; such bituminous coal is called "coking coal." Bituminous coal that is suitable for making the producer gas used in the open-hearth steel process is called gas coal. Any bituminous coals suitable for making blast-furnace coke or foundry coke, or that can be satisfactorily used for making producer gas, are classed as metallurgical coals and as such are to be considered in my proposed plan for the evaluation of metallurgical coals. According to Bureau of Mines Bulletin No. 449 these coals comprised 22 per cent of the bituminous coals mined in this country in 1923.

Jan 1, 1926

By A. Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30 000 tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors, in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400 m causing a major failure of the north-west wall involving close to 100 Mt of waste material.

Jan 1, 2006

By R. L. Grant

[p(,ton~to'rs 'ar-IV uscG.. to explode 9crnli .... sible c}:plosivcs, dynamites, or other hiGh uxplosives. This ?,...!xplosion or detr)nation is brought about by th\.:J energy which i liberated as a cOl":"Lb' nation of concusBion and heat wl1en the ? detonator is fired. 'm Ot:18t? I'l(jrds~ liThe detonator is the key VI: ich unlocks the enerGY of a llgh? explosIve""? (8) :1/. Being sensitive nd latently dangerous, detonators ITl.ust lTIeet t\V0 primary requirerDentr: They must be ..;.afe to handle and IT. list? detonate' when (l,esired, the ... eby iIr.parting deton:l.tion to the explo8ivc cJ.1Cire-e.]

Jan 1, 1941

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.