Search Documents

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By H Guthrie, J Hodder, J Bain, S Durkin

Australian mines have traditionally relied on diesel powered vehicles to fulfil their light vehicle needs. There are many reasons for the resources industry to review its use of diesel-powered vehicles. The international industry has developed projects to explore the use of Battery Electric Vehicles (BEV) as a more sustainable alternative to traditional diesel-powered vehicles. While the technology for cost-effectively applying modern high-performance lithium-based batteries to the mining environment has existed for over a decade it is yet to be widespread throughout the industry. Through the collaboration of Safescape, 3ME Technology and Kirkland Lake Gold, with funding from Mining Equipment technology services (METS) Ignited, the project has focussed on advancing the Australian METS sector’s capability in the rapidly approaching implementation of BEV technology. This paper reports on the collaborative approach to develop a prototype vehicle; explains the selection criteria for the various components of the vehicle; and details the risk-based approach to developing a scalable product to replace existing underground light vehicle fleets. The prototype vehicle was tested underground at Kirkland Lake Gold’s Fosterville operations in Victoria beginning in October 2019. Reporting from these trials focusses on the key factors affecting underground operations. These include driveability, safety, charging and cycle times. Gathering data around energy consumption through normal daily duties enabled a model of energy consumption and charging requirements to be developed such that various applications of the electric vehicle can be considered against existing diesel-powered vehicles. This has provided insight into the impact on daily operations, and the way forward for large scale implementation.

Mar 15, 2021

The Golden Ridges Mine, one of the properties of New Guinea Goldfields Limited, is situated on the right bank of Nami Creek, not far from the township of Wau, in the Territory of New Guinea.The property is somewhat unique, in that the goldbearing ore-body occurs in the form of a flat seam-like deposit lying on a volcanic breccia, and covered with a mantle of overburden of decomposed porphyry. The overburden varies in thickness up to a maximum of about 65 ft.The ratio of overburden to ore is about 3 to 1. The practice developed is to strip the overburden by hydraulicking, and to mine the exposed ore under open-cut conditions, blasting to a vertical face, and using electrically operated scraper hoists for conveying the broken ore to the mill bins.The stripping of the overburden involves the boring of well-drill holes, blasting the holes and then hydraulicking the shattered material.

Jan 1, 1934

By F. F. ESPIE

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Australia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are beginning to experience where industry no longer 'calls the tune'. We miners have been quick to point out and emphasize, that ours is a 'high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a 'distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas-of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to eliminate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

The copper and zinc contents of herbarium specimens of 11 of the 12 Australian species of Polycarpaea were determined in order to establish background and anomalous values of potential use in biogeochemical prospecting.Cumulative frequency curves were used to establish appropriate threshold concentrations for six species including the "copper plant"' P spirostylis. Collection localities of Polycarpaea specimens with anomalous copper or copper-and-zinc values are under investigation.

Jan 1, 1978

By F. B. Henderson III

Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By J. A. Marshall

"INTRODUCTION The purpose of this paper is to investigate the potential for use of UAVs in underground mines and present a prototype design for a novel autorotating UAV platform for underground 3D data collection. The mining industry has recently shown increased interest in the use of unmanned aerial vehicles (UAVs) to assist in everyday operations [20, 11, 4]. Above ground, small UAVs are in some cases a more efficient, inexpensive, and safer alternative to manned aircrafts currently used for photography, inspection and security [6, 10]. For example, attaching camera, infrared and LiDAR payloads, UAVs can provide a low-cost method of obtaining highly accurate 3D photogrammetric data and aerial photography. UAVs are now commonly used in open pit mining operations for applications that include stockpile surveying, 3D pit modelling, facilities management, accident reporting, progress monitoring, and environmental assessment [11]. There are numerous companies offering UAV services for mining applications; e.g., UAV Geomatics, Leica Geosystems, Sky Futures, SenseFly and FlyTerra, to name just a few. Common services include stockpile and open pit volume computations, environmental assessment, aerial mapping and photogrammetry. Although the aforementioned services are thosemost commonly provided by UAV surveying companies, they may also add value to other daily mining operations. For instance, SenseFly offers pre and post-blast monitoring in order to identify the presence of misfires and wall damage. This data can also be used to reconcile the blast results with expected results. GEM Systems offers a UAV equipped with a magnetometer for mineral exploration surveys. Companies such as Barrick have even used UAVs for solids modelling at tailings dams and stability monitoring [11]. UAVs in mining have so far been mostly limited to surface applications. Harsh underground environments pose many obstacles for flying UAVs. The confined space, dampness, reduced visibility, air movement, and lack of control signal propagation hinders most operators from being able to fly a drone underground. It may be that truly practical uses for UAVs underground will require either autonomous or semi-autonomous flight capabilities. Although there are many difficulties with flying underground, the potential benefits from a working system could greatly improve mining operations. The potential benefits of deploying UAV platforms underground include access to unreachable and dangerous locations and removing personnel from unsafe situations. These benefits have the potential to greatly improve mine monitoring and mine safety. Research has shown that current UAV technologies exist that allow for autonomous indoor flight. Extensive research has been done to develop UAV systems that are capable of performing on-board simultaneous localization and mapping (SLAM), which can allow them to navigate and map a foreign environment autonomously [5, 7, 1, 13]. Grzonka [7] successfully used an open hardware quadrotor to autonomously navigate and map an office building. The research outlines the localization, mapping, path planning, height estimation and control of the autonomous quadrotor. Other research has been done that exploits autonomous UAVs for search and rescue. Kassecker [9] proposed a software and hardware framework for a quadrotor capable of indoor and outdoor urban search and rescue and Rudol [19] developed a system for human body detection and geolocalization using an autonomous UAV.The use of autonomous UAVs in search and rescue has the potential to improve situational awareness and surveillance for a rescue team. Similar research has been done that uses autonomous UAVs for indoor exploration. Pravitra [15] outlined a strategy for autonomous exploration of miniature air vehicles (MAVs) within indoor environments and Rudol [19] developed a method for using an unmanned ground vehicle (UGV) and a UAV for cooperative indoor exploration. These studies show that aut"

Jan 1, 2017

By Braden Lusk, Paul Sainato, Josh Calnan, Hiago Vasconcelos, Luis Felipe Marinho

"Blasting and rock fragmentation is one the most important unit operations in mining. Since itsintroduction into the mine production cycle, mining has become more efficient in mineral production(Hartman, 2002). Widely used with the main objective of breaking rock mass in smaller fragments to be loaded and hauled at a minimum cost, blasting is optimized when stemming materials properly confine drillholes charged with explosives. Halim Cevizci (2013) performed a stemming application using Gypsum plaster, a kind of material that exhibits solid-like behavior when it is dry. Based on his theory, the present article reports an experiment using another type of material that shows similar behavior, non-Newtonian fluids. The primary goal of this study is to measure the confinement effectiveness provided by a non-Newtonian mixture as the stemming component. The study also analyzes the explosives’ energy propagation throughout the rock mass relating to the stemming materials applied. Currently, mining literature recommends the application of dry granular materials in stemming columns, because of its inertial and high frictional effects (Hagan, 1973). However, the test verified that the mixture added to the stemming column was able to reduce energy and gas losses to the atmosphere, because of the liquid’s property of filling voids in the material. The solid-like behavior of the non-Newtonian mixture was investigated for its capability to improve borehole confinement, since the mixture reacts like a solid when under shear stress. The results were compared to those from sand and air stemming applications, configured in different arrangements. It was concluded that the non-Newtonian mixture yielded high results due to its better confinement effectiveness, a reduction of air overpressure, and an increase of the strain propagation and ground vibration throughout the rock."

Jan 1, 2016

By R. Codell, D. L. Hughson

While benchmarking the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings, we found numerical simulation of dripping threshold flux consistently higher than the analytical solution for both rectangular and unstructured grids. The magnitude of error is proportional to the alpha parameter characterizing capillarity. This may bias estimates of repository performance towards non-conservatism.

Jan 1, 2000

The Torington Lodes.This paper describes investigations into mineralogical, petrological and structural associations of cassiterite in occurrences of economic value. The work was carried out in three mines, during a number of years, in the hope that the, data collected might be helpfulin the search for occurrences of cassiterite in stanniferous zones and reduce unproductive exploratory work. Tin-bearing lodes at Torington, in the New England district, New South Wales, have been worked since 1880, and the locality is the most important centre of lode tin occurrence in the, State. The township of Torington is 18 miles westerly from Deepwater, a station on the Great Northern Railway, 446 miles from Sydney.The tinfield forms part of the Mole Tableland, which has an altitude between 3,000 ft. and 4,000 ft. above sea level. The country rock, in which the stanniferous lodes occur, is granite of Permian age, which has been intruded into Carboniferous claystone. An inlierof claystone is exposed to the west of the stanniferous area, 'and in it, close to' its contact with the enclosing granite, are occurrences of wolfram and bismuth. These minerals, together with chalcopyrite, pyrite, arsenopyrite, zinc blende, galena and molybdenite, in very small quantity, are associated with cassiterite in lodes traversing the granite, particularly near the claystone, but decrease in amount with distance from the contact. Their occurrence is sporadic and usually causes no trouble in dressing the cassiterite concentrate, the final product containing less than 1% of total penalisable impurity. In Curnow's mine, pyrite, galena and molybdenite have been observed at 700 ft. from surface.The granite is of the biotite type and its structure may be divided into four groups, or classifications, arising from segregation processes during cooling and consolidation. The four classes, in order of extent of distribution, are:1. Granite of normal type, in which the constituent quartz felspar and mica, have a particle size approximately 14, in.2. Porphyritic granite, in which the felspar particles are from % in. to lin. in size, that of the quartz and mica approximately % in.3. A fine-grained granite, in which the particles of all constituent minerals are % in. or less in size;4. A rock of highly siliceous ground mass containing very small particles of felspar and almost negligible biotite.Type 1 is the general type of granite in all mines of the field; types 2 and 3 may occur as large masses, or all three classes may merge rapidly one into the other, and all be disclosed in 20 ft. of driving. Usually, however, the segregations are massive, but are not associated with any special horizon. For instance, a mass of porphyiiticgranite extends from surface to a depth of 440 ft., for a distance of 350 ft. south from the New England main shaft. The upper levels of Curnow's mine, 14" mile south-east, are in normal granite, but a restricted mass 'of porphyritic granite occurred between Nos. 5 and 6 levels, or 400-500 ft. below the collar of the shaft...

Jan 1, 1950

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By Paul D. Tomlingson

Editor's note: This is the first of two articles on maintenance. Part two, "Effective maintenance downsizing techniques," will appear in the October issue of MINING ENGINEERING. Most mine managers are aware that the cost of maintenance rarely goes down unless work is done less often and with fewer people. Fewer people translates into downsizing and seldom means making maintenance more efficient. Even so, mines that have struggled unsuccessfully to improve maintenance and are now pressed to reduce maintenance costs may opt for downsizing. On the other hand, mines with an immediate need to reduce costs may be forced to downsize because they cannot wait for needed improvements to take effect. This can be bad news for maintenance. In any case, the mine must downsize correctly to ensure effective maintenance is sustained.

Jan 1, 1994

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2017

By E. H. Denny

In discussing safety in Colorado metal mines there are two important points for metal -mining men to consider , namely , the direct and indirect cost of accidents and the possibility and means of preventing accidents . For statistics on Colorado metal - mine accidents , reference has been made to published reports of the United States Bureau of Mines on metal- mine accidents from 1919 to 1927. This period was considered because only with the year 1919 are complete figures on nonfatal accidents available and because these years represent postwar activities ; 1927 is the last year for which the U. S. Bureau of Mines has published accident statistics . During the nine -year period 1919 to 1927 , inclusive , 153 metal miners were killed by mine accidents in Colorado and 5,035 miners suffered lost - time injuries . The accidentfrequency rate of number killed per 1,000 300- day workers for this nine - year period was 4.68 as compared with the general average of 3.26 for all the metal mines of the United States for the same period . In other words , the fatality rate in the metal mines of Colorado for this nine- year period averaged 40 per cent higher than that of the metal- mining industry in the United States generally . In 1924 and 1926 the Colorado metal mines had a better accident record than the average of those of the United States , but 1927 was a bad accident year and the State Bureau of Mines figures for 1928 and 1929 showing respectively 18 and 23 men killed in and about the metal mines indicate a continuing relatively high death rate from accident . The cost of accidents to the miner for the period 1919 to 1927 can be estimated from the accident figures just given . The United States Bureau of Mines as well as other authorities assess 6,000 days lost time for every fatality and every permanent total disability . These authorities have also agreed that a permanent partial disability costs 800 days lost time to the worker over his working lifetime , that lost time injuries of less than 14 days average about 6 days lost time and lost time injuries not involving permanent disability but having loss of more than 14 days average 32 days lost time . On this basis the Colorado metal miners have suffered in nine years a gross loss of 1,214,146 days , or , at $5 per day , $6,070,730 . The miner receives about one -ninth of this amount in compensation so that the net loss to the metal miner in Colorado for this nine - year period was about $5,400,000 .

May 1, 1930

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937