Search Documents

By Ana Clara Petrucelli

A principal ferramenta de controle do processo BOF reside na regulagem do sopro de oxigênio. A análise dos parâmetros de interação entre o sopro e o banho metálico compõe o objetivo deste trabalho. Através de uma análise visual da penetração e fração volumétrica da bacia de descarburação, foi determinada a melhor configuração de sopro entre diferentes combinações de bicos multifuros (3 a 6 furos), distância lança-banho e vazão. Foram feitas previsões sobre a penetração do jato a partir de um balanço de energia a fim de validá-las com o modelo físico. As maiores penetrações foram alcançadas com os bicos de 3 e 4 furos, com a maior vazão e menor distância lança-banho dentre os padrões testados. Todavia, as maiores frações volumétricas da bacia de descarburação foram obtidas com 5 e 6 furos, vazão e distâncias variadas dentre as ensaiadas.

Jul 29, 2018

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By Russell L. Wood

The title of this session seems to have been picked especially for this paper. It is 1984, it is the morning after, and there is one monumental hangover among many if not most of the oil companies that have invested in mining in the past decade or so. How an oil company looks at mining depends on what time period you are talking about. A few years back around the time of investment this is what they were probably looking at: 1. A balance sheet of their own that was beginning to go wild, with many of their commodity prices having already seen increases of two, three, or four fold, and with no end in sight. 2. A need to invest their earnings someplace fast before the stockholders or the government got too interested. And that someplace should be in an industry where their own management skills could be applied. (Only a true cynic would suggest that this is a form of job security) 3. In mining there was an industry amazingly similiar to their own, one working with non-renewable natural resources, dealing with the same types of government agencies, and having the same type of critics and pressures from the general population. 4. An industry that was somewhat backward as compared with their own, and one where a generous ration of the capital and management skills so handsomely bestowed upon the oil industry could be used to great advantage.

Jan 1, 1984

Comparison of Grinding and Liberation Processes for Stalky Biomass Materials as a Prerequisite for Production of Energy Pellets with High Calorific Value Pelletising biomass, especially straw and stalky materials, requires a product specific size reduction and liberation. However, moisture content plays an important role in palletising and also affects the energetic properties of the biomass. The paper illustrates the characteristics of the mentioned type of biomass and specifies the necessities for production of energy pellets. Defined requirements for biomass energy pellets will be shown based on relevant standards. The work focuses on a comparative investigation of the straw fibres after grinding with hammer/impact mill and after the liberation of the straw fibres with twin-screw extruder (two different communition units). A traditional hammer mill as well as an hydrothermal process taking place in a twin-screw extruder were utilised. Results of the grinding and liberation of rye and wheat straw fibres are discussed based on a detailed particle characterisation (particle size and shape distribution). Besides high calorific value the main pellet quality parameters are mechanical stability, abrasion resistance and further combustion technical characteristics. The particle size distribution displayed optimum characteristics for the combustion processes to be carried out in a furnace. The durability of the pellets produced from straw fibres liberated with twin-screw extruder was comparatively better then that prepared with the straw fibres after grinding with impact mill. Particle size distribution, abrasion values and the strength characteristics showed a good correlation with each. The high presence of N and S would result in high NOx and SOx emissions, where as the high concentrations of Cl would corrode the furnace. These chemical properties of the straw would restrict its usage in small scale furnaces.

Sep 13, 2010

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

Spectroelectrochemical Investigation of Hydroxamate Reagents on Copper Oxide Minerals

Sep 13, 2010

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By M. F. Goodrich

The concept of using water-only cyclones as a clean coal scalping device preceding a heavy media cyclone circuit shows considerable promise, as it can considerably reduce the feed to the heavy media cyclone circuit. The system will not perform as well as a heavy media cyclone circuit alone, but the resultant loss in yield is small and may be negligible under some conditions. The concept of water-only cyclone scalping has previously been suggested by others. By reducing the amount of raw coal to be processed in the more expensive circuits overall capital and operating costs may be reduced. There are a few commercial plants with circuits operating on this concept. In the Warwick and Rowland plants water-only cyclones are used to scalp the feed to a heavy media vessel and Deister tables respectively while Amherst Coal Company's McGregor plant uses them to scalp the feed to a heavy media cyclone circuit. The system was evaluated on a technical basis, both from a theoretical viewpoint and by analysis of a computer simulation, in order to gain a fuller understanding of its usefulness and limitations.

Jan 1, 1977

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

The role of a project metallurgist is diverse and covers input into the resource definition, mining studies, metallurgical test program development, process engineering and plant design, cost estimate preparation and financial analysis aspects of project feasibility studies. Mining project schedule and cost overruns can often be attributed to cutting short metallurgical test work, engineering and cost estimating leading up to commitment to development. In a significant number of cases this may result from the lack of understanding and commitment by the project proponent to the requisite metallurgical and processing studies required during the various pre-commitment stages of a mining project. Metallurgical test work, process development, engineering and cost estimating requirements for each stage of pre-commitment development are described together with a summary of the ongoing role of the project metallurgist during detailed engineering and commissioning of a process plant.

Jan 1, 2008

By Mônica Aline Magalhães Gurgel

Este trabalho avaliou a evolução estrutural e mecânica dos ciclos térmicos realizados em uma chapa laminada a frio de aço baixo carbono com micro adição de molibdênio e nióbio destinado para a indústria automobilística, associado a classe dos aços bifásicos. Para realização do estudo foi feita a caracterização microestrutural e mecânica, por intermédio de amostras retiradas após a laminadas a frio produzidas em escala industrial, com auxílio das técnicas de microscopia óptica, e avaliação da dureza via Nanoindentador Instrumentado. Os ciclos térmicos foram feitos com o intuito de observar os processos de recuperação, recristalização, e transformação de fases no aquecimento e após resfriamento, com encharque em distintas temperaturas do campo intercrítico, via análise de dilatometria em um equipamento de análise termomecânica (TMA) em amostras extraídas da chapa laminada a frio “Full- Hard”.

Aug 16, 2017

By Gordon E. Green

This report addresses remote monitoring of coal waste impoundments for stability. Existing automated geotechnical monitoring systems are described and reviewed along with details of instruments suitable for such systems. An impoundment in West Virginia which was in the construction stage was instrumented and monitored between July 1979 and may 1981. Sensors which measure surface and subsurface parameters including settlement, horizontal deflection, surface tilt, pore water pressure, seepage, pond level, and meteorological parameters were installed. Data from the 37 sensors were collected by on-site logger and transmitted by telephone to a central processing station in Seattle for recording and interpretation. Difficulties were encountered with telephone and powerline outages and malfunction of electronic units. Detailed descriptions of the design and performance of the system are provided along with evaluation and comparison with other systems. Recommendations for improving and expanding the capabilities of the monitoring system are given.

Jan 1, 1982

By Met B. E

During the operation of the Parkes process of desilverising, and in the earlier days of the continuous process, gold and silver were removed separately from softened lead bullion. Gold was removed in the Parkes process by a selective zincing, and -in the continuous process by treatment with zinc in a special de-golding kettle, in each case a crust being obtained carrying the gold and a small portion of the silver. Actually the process could have been more correctly termed a de-copperising process, on accountof the relatively large amount of this metal present, and its affinity for zinc, which caused it to enter the crusts produced.The crust was treated in reverberatory furnaces, where the bulk of the copper and zinc was removed in by-products, and the resulting "gold bullion" cupelled to give adore bullion containing approximately 2,000 ounces gold per ton.For the purpose of parting this dore, a small Balbach-Thum plant of 11 cells was used, and once each six months a short campaign was conducted on the accumulated metal.With the development of the process of de-copperising smelter bullion by means of sulphur, when a bullion averaging about .004% copper was constantly available for refining, the need for a separate de-golding process disappeared.The de-golding kettle of the Continuous Process...

Jan 1, 1937

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

By Bolmerm R. L.

This information circular describes the application of modern methods and equipment in sinking a vertical, 916-foot-deep by 16-foot-diameter, concrete-lined access shaft for the Harold D. Roberts tunnel near Montezuma, Colo. Although the access shaft was merely a construction facility to expedite completion of a 23-mile water-diversion tunnel, a circular shaft of this type would be equally adaptable for mine development or other purposes. Comparable sinking methods and equipment could be used for similar shafts within a wide range of sizes and depths. SUMMARY In addition to excavation and support of the basic access shaft to tunnel grade, the overall sinking project involved initial preparation of a surface site and plant, subsequent construction of a tunnel-level station and loading pocket at the shaft bottom, and ultimate conversion of the basic shaft into a hoisting and access facility for tunnel operations. The sinking period for the basic shaft approximated one year. Actual tunnel operations through the converted shaft began on April 3, 1958, approximately 19 months after the project was initiated.

Jan 1, 1961

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007