Search Documents

By William H. Spice

The year 1942 in the South Central Texas area was marked by a sharp curtailment of exploratory drilling as compared with the past several years. In the 33 counties that compose this district, 17 of which are nonproducing counties, only 51 exploratory wells were drilled during the year 1942. This compares with 118 exploratory wells drilled during 1941, or a decrease of more than 50 per cent. At the end of the year 10 active exploratory wells were drilling in this area, as against 19 being drilled at the end of 1941. Of the exploratory wells drilled, two brought in oil wells and were new field discoveries and one was a gas well extending a recently discovered shallow gas area in the western part of the district. This compares with five new oil fields, one new . gas field and two extension wells drilled in 1941. Both new field discoveries were small and in areas outside of the general trend of the main producing horizon of the district in Edwards limestone: One new field, the Imogene, in Atascosa County, is a deep Edwards limestone prospect at 7500 ft., and the other new field, the Poth, in Wilson County, is a sSEa110w Wilcox (Eocene) prospect at 4000 ft. Subsequent drilling in each field to the end of I942 has proved disappointing. There were no new discoveries along the old Balcones fault-line trend, although 35 of the exploratory wells were drilled in counties along this trend. Approximately 38 wells were drilled in or adjacent to the proven fields of the district, of which 18 were oil wells, 2 were gas wells and 17 were dry holes. The district produced 6,186,178 bbl. of oil during 1942, which was a 7 per cent decrease under production for 1941. Approximately 4,961,000 bbl. of this total production, a slight increase over 1941, was produced by the four Edwards-limestone fields, Luling, Branyon, Salt Flat and Darst Creek, and the rest of the production came from the other 42 active fields in the district. During the year, 20 new producing wells were completed and 221 wells were abandoned in the producing fields. This alarming excess rate of abandonment~ over completions will be further reflected undoubtedly by a further decreased rate of 1943 production under 1942. Two active fields in the district in which more than one producing well was completed during the year were Bee Creek and Washburn. The majority of exploratory work in the district was confined to areas along the Wilcox trend, with a certain amount in progress along the deeper Edwards limestone trend. The successful completion of sevemi wells in the Washburn field from multiple sands in the Lower Wilcor (Eocene) has stimulated exploratory work along this trend, while the completion of a small well in the Imogene field from the Edwards limestone at 7500 ft. has renewed interest in this horizon at depths greater than generally are producing in the district. New Fields ounty. ble Oil and Refining Company's No. I

Jan 1, 1943

By R. M. Hays

At the present time, oxidized taconite and semitaconite are not processed on the Mesabi Range except in vely limited tonnages. However, it is estimated that by 1990 shipments from the Range will approach 75 million tons of iron ore per year. To achieve this and future production, either additional magnetic taconite reserves must be proven or oxidized taconite and semitaconite must be processed. One beneficiation process which uses high-intensity magnetic separation and flotation for concentrating oxidized taconite and semitaconite is described. Detailed metallurgical results are given and an economic evaluation of the process is presented with comparison to other processes. The results of the present study indicate that the high-intensity magnetic separation and flotation process appears nearer commercialization for the processing of Mesabi Range semitaconite. The disadvantages of the process are nearer solution and are being solved by well-defined programs. During the twentieth century, the Mesabi Range in northeastern Minnesota has been the main source of iron ore for American steel mills. The Mesabi Range, which is about 120 miles long and up to 3 miles wide, is the pre-glacial outcrop of a group of sedimentary iron-bearing rocks known as the Biwabik formation. The formation, which is 200 to 650 ft thick and dips 50 to 10° to the southeast, is divided into four stratigraphic units. From top to bottom, these are the Upper Slaty, Upper Cherty, Lower Slaty, and Lower Cherty. Since its deposition in Precambrian time, most of the original Biwabik formation has been subject to alteration. Thus, although the iron content of the original formation was quite uniform, major variations in mineral composition now occur both laterally along the length of the formation and vertically within its units. Details of the mineralogical variations in the Biwabik formation have been described by Wolff,' Gruner, 2 and White.3 The unaltered portion of the Biwabik formation includes the magnetite taconites which are being commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons of iron ore pellets per year and have produced approximately 170milion tons of pellets since 1956. Capacity for another 30 million tons of pellets per year is being considered by the industry for the next ten years. This increase will be obtained by constructing new plants and by expanding present operations. Thus, by ! 978, it is estimated that approximately 60 million tons of iron ore vellets will be produced each vear from the magnetite taconites of the Biwabik formation. The portions of the Biwabik formation subjected to intense alteration resulted in direct shipping, wash, and heavy-media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron ore for American steel mills. In 1967, about 11 million tons of direct shipping ore and 13 million tons of wash, jig, heavy-media, and other gravity concentrates were shipped from the Mesabi Range.4 These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from 24 million tons in 1967 to 6 to 8 million tons in 1975.' This decrease will

Jan 1, 1970

By William H. Spice

The year 1942 in the South Central Texas area was marked by a sharp curtailment of exploratory drilling as compared with the past several years. In the 33 counties that compose this district, 17 of which are nonproducing counties, only 51 exploratory wells were drilled during the year 1942. This compares with 118 exploratory wells drilled during 1941, or a decrease of more than 50 per cent. At the end of the year 10 active exploratory wells were drilling in this area, as against 19 being drilled at the end of 1941. Of the exploratory wells drilled, two brought in oil wells and were new field discoveries and one was a gas well extending a recently discovered shallow gas area in the western part of the district. This compares with five new oil fields, one new . gas field and two extension wells drilled in 1941. Both new field discoveries were small and in areas outside of the general trend of the main producing horizon of the district in Edwards limestone: One new field, the Imogene, in Atascosa County, is a deep Edwards limestone prospect at 7500 ft., and the other new field, the Poth, in Wilson County, is a sSEa110w Wilcox (Eocene) prospect at 4000 ft. Subsequent drilling in each field to the end of I942 has proved disappointing. There were no new discoveries along the old Balcones fault-line trend, although 35 of the exploratory wells were drilled in counties along this trend. Approximately 38 wells were drilled in or adjacent to the proven fields of the district, of which 18 were oil wells, 2 were gas wells and 17 were dry holes. The district produced 6,186,178 bbl. of oil during 1942, which was a 7 per cent decrease under production for 1941. Approximately 4,961,000 bbl. of this total production, a slight increase over 1941, was produced by the four Edwards-limestone fields, Luling, Branyon, Salt Flat and Darst Creek, and the rest of the production came from the other 42 active fields in the district. During the year, 20 new producing wells were completed and 221 wells were abandoned in the producing fields. This alarming excess rate of abandonment~ over completions will be further reflected undoubtedly by a further decreased rate of 1943 production under 1942. Two active fields in the district in which more than one producing well was completed during the year were Bee Creek and Washburn. The majority of exploratory work in the district was confined to areas along the Wilcox trend, with a certain amount in progress along the deeper Edwards limestone trend. The successful completion of sevemi wells in the Washburn field from multiple sands in the Lower Wilcor (Eocene) has stimulated exploratory work along this trend, while the completion of a small well in the Imogene field from the Edwards limestone at 7500 ft. has renewed interest in this horizon at depths greater than generally are producing in the district. New Fields ounty. ble Oil and Refining Company's No. I

Jan 1, 1943

By R. J. Blackwell, J. R. Rayne, W. M. Terry

This paper presents results of an experimental investigation of factors that control the efficiency with which oil is displaced from porous media by a miscible fluid. The study was made to elucidate the relevant processes both on microscopic level (within individual or between neighboring pore spaces) and on macroscopic level (within a large sand body). Mixing of miscible fluids on the microscopic level was studied in sand-packed tubes. It was found that molecular diffusion is the dominant dispersion mechanism for reservoir conditions of rate, length and pore sizes. Macroscopic channeling was studied for various mobility ratios in reservoir mode1s scaled to relate viscous, gravitational, and diffusional forces. The formation of channels was due to viscous firzgering, gravity segregation and variations in permeability. With adverse mobility ratios, it was found for reservoirs of realistic widths that diffusion will not be effective in preventing the formation and growth of fingers, even in homogeneous sands. At sufficiently low rates channeling was eliminated by gravity segregation in tilted reservoirs. The dependence of recovery on mobility ratio, length-to-width ratio, flow rate and angle of dip is presented. INTRODUCTION Oil recovery by solvent flooding is finding increasing application in the field. While the process promises high recoveries from the region swept by solvent, under adverse conditions only a small fraction of the reservoir volume may be swept at the time solvent breaks through to the producing well. Further, the high cost of the solvent encourages its use only as a bank whose size must be kept at a minimum. Thus, two important questions arise: (1) what fraction of the reservoir can be swept, practically, by solvent? and (2) what is the minimum size solvent bank that can be used to carry out the displacement? The answers to these questions require knowledge of both macroscopic channeling processes and microscopic mixing processes. The studies described here were carried out to gain this knowledge. Microscopic mechanisms which cause mixing will be discussed first, because an understanding of these mechanisms is necessary for proper interpretation of the experimental work on channeling described later. INVESTIGATION OF MICROSCOPIC DISPLACEMENT PHENOMENA FOR MISCIBLE FLUIDS The questions to be resolved concerning microscopic displacement behavior are: (1) how much mixing occurs between oil and solvent in the direction of flow? and (2) does the solvent completely flush the oil from the pore spaces in the region invaded by solvent? The classic work of Sir Geoffrey Taylor' and its extension by Aris2 have shown that it is possible from theory to describe the amount of mixing in single straight capillaries when solvent displaces a fluid of equal viscosity and equal density. Aris showed that the lengths of the mixing zones, 81, corresponding to the 10 per cent and 90 per cent concentration levels of the solvent can be calculated from the formula, 81 = 3.62 \/Kt, .........(1) where 8l is the length of the mixing zone, cm; t is the time, sec; and K is the effective dispersion coefficient, cm2/sec, given by K/D = 1 + (1/48) (au/D)2......(2) where a is the radius of the capillary, cm; D is the molecular diffusivity, cm2/sec; u is the average velocity

By C. G. Dunn, F. W. Daniels

IN recent publications1-5 the existence and behavior of subgrain boundaries in high-purity metals has been clearly brought to light. Lacombe and Beaujardl by means of special etching methods disclosed in polycrystalline sheets of aluminum the existence of substructures differing in orientation by small amounts (about 1/4"). Boundaries of these structures at relatively high temperatures had the remarkable property' of moving about while the ordinary boundaries remained stationary. Cahn2 also observed substructures in bent and annealed single crystals of aluminum, zinc, magnesium, and rock salt. The position of subboundaries could be explained in terms of a dislocation mechanism of polygonization in which dislocations move into lines at right angles to the bent glide planes thereby relieving elastic stresses in these planes. Guinier and Tennevin8,6 disclosed the further interesting feature that polygonized structures coarsened significantly upon prolonged annealing. Somewhat similar subgrain phenomena have been observed in silicon iron of commercial purity. Although some evidence for the development of macro-mosaic structures in silicon iron already has been reported by one of the authors6,7 under the phenom-enological term "crystal recovery," much better evidence recently has been obtained due to improved etching techniques. In addition, phenomena regarding structural changes have been uncovered. The present investigation is divided into three parts: (1) The phenomenon of Laue spot sharpening on annealing cold-rolled crystals, (2) the phenomena of polygonization and subgrain coarsening The material used in the present investigation was high-grade commercial silicon iron sheet of nominal composition, 3.3 pct Si, 0.004 C, 0.011 P, 0.010 S, 0.04 Mn, 0.01 Al, 0.04 Cu, 0.01 Sn. Large single crystals of this material Were prepared for cold-rolling or bending as scheduled. Cold-rolling of 12 pct was carried out on a laboratory 8-in, diam rolling mill. The bending deformations were performed by pressing the crystals between a solid Fig. 2—lllustrative foue patterns to show Laue spot sharpening. a (Left)—Specimen as cold rolled, b (right)—After 48 hr at 1400°C. round bar and a mating half cylinder, both heavily greased. Individual specimens were cut from the deformed crystals, and the cut edges were deeply etched prior to annealing. Laue photographs were made using 40-kv tungsten radiation. The technique used to disclose the various subboundaries was an electropolish and electroetch in a bath of chrome-acetic acid.' The anodic polishing done at 22 v was immediately followed by etching at a reduced voltage, which was dependent upon the nature of the subboundaries. Phenomenon of Laue Spot Sharpening on Annealing Cold-Rolled Crystals Fig. 1 gives the initial and final orientations of the specimens cold-rolled 12 pct. Each specimen was annealed at a temperature and for a time which caused significant structural changes as evidenced by alterations in Laue patterns. Representative Laue patterns and micrographs showing the essential changes are given in Figs. 2, 3, and 4. The essential points to be derived from these illustrations follow: 1. Annealing at 950°C clearly develops a substructure with the orientation of the cold-rolled specimen. 2. The subboundaries formed obviously separate regions of nearly the same orientation. Some of the subboundaries appear as a sequence of dots similar to those observed in aluminum by Lacombe and Beaujard,' but whether this is due to extremely small differences in orientation is not known at present. 3. The substructure coarsens upon prolonged annealing. 4. Prolonged annealing also causes a decrease in orientation spread according to Laue spot sharpening'

Jan 1, 1952

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

G. F. LOUGhlin,* Washington, D. C.—With reference to Mr. Bain's paper: The scarcity of adequate geologic data on building stone reflects, among other things, a lack of interest on the part of geologists. It has been one of my duties to attend to matters relating to building stone and other structural materials that have come to the U. S. Geological Survey, but for several years my principal administrative and other duties in the Section of Metalliferous Deposits have prevented me from giving structural materials the attention that they deserve. I have felt that investigations relating to structural materials should be assigned to someone else, but thus far nobody with a sufficient interest in the subject has come forward; further, the specific calls for these investigations have been so few and far between that it has not seemed practical to draft any one for the job. The general situation is such that steady and substantial progress in the application of geology to the utilization of structural materials is not likely to be made unless someone with keen interest in the subject takes the initiative. If the start is once made, I know from experience that cooperation from the more progressive members of the quarry and building industries will be readily forthcoming. Mr. Sales' suggestions are all constructive and most welcome. A thorough, detailed discussion of them might be as long as his manuscript, but could largely be summarized with the one word "amen" qualified by the alibi that a chronic shortage of funds and therefore of personnel has prevented us from carrying out some of his suggestions already. A few of them might call for an Act of Congress before we could undertake them, and one or two, such as the preservation of mine maps, with which I heartily agree, would call for much additional space as well as clerical and supervising help. Several items in Mr. Sales' paper—for example, the question of balance between the scientific and more directly practical studies and the surveys or resurveys of the larger and smaller mining districts—have been covered in my contribution to the symposium. The suggestion of frequent reviews of progress in the study of ore deposits is excellent and can be followed without serious diversion from projects already on the Survey's program. Brief reviews by Survey men have been published in periodicals, and the contributions by several of them to the Lindgren Volume1 may also be cited as serving this purpose to some degree. The practice of publishing short papers by Survey men in outside journals rather than in Government reports is largely the result of experience and expedience. Our printing funds are limited, and considerable time must elapse between the transmittal of a paper and its publication. Time is saved therefore by sending papers to outside journals, and the editors of those journals are usually glad to receive them. Members of the Survey would doubtless prefer to have the products and byproducts of their official work appear in official Survey publications if conditions were more favorable. If we were left entirely to ourselves the balance between the more scientific and the more directly practical studies would be somewhat better than it is, but the

Jan 1, 1935

G. F. LOUGhlin,* Washington, D. C.—With reference to Mr. Bain's paper: The scarcity of adequate geologic data on building stone reflects, among other things, a lack of interest on the part of geologists. It has been one of my duties to attend to matters relating to building stone and other structural materials that have come to the U. S. Geological Survey, but for several years my principal administrative and other duties in the Section of Metalliferous Deposits have prevented me from giving structural materials the attention that they deserve. I have felt that investigations relating to structural materials should be assigned to someone else, but thus far nobody with a sufficient interest in the subject has come forward; further, the specific calls for these investigations have been so few and far between that it has not seemed practical to draft any one for the job. The general situation is such that steady and substantial progress in the application of geology to the utilization of structural materials is not likely to be made unless someone with keen interest in the subject takes the initiative. If the start is once made, I know from experience that cooperation from the more progressive members of the quarry and building industries will be readily forthcoming. Mr. Sales' suggestions are all constructive and most welcome. A thorough, detailed discussion of them might be as long as his manuscript, but could largely be summarized with the one word "amen" qualified by the alibi that a chronic shortage of funds and therefore of personnel has prevented us from carrying out some of his suggestions already. A few of them might call for an Act of Congress before we could undertake them, and one or two, such as the preservation of mine maps, with which I heartily agree, would call for much additional space as well as clerical and supervising help. Several items in Mr. Sales' paper—for example, the question of balance between the scientific and more directly practical studies and the surveys or resurveys of the larger and smaller mining districts—have been covered in my contribution to the symposium. The suggestion of frequent reviews of progress in the study of ore deposits is excellent and can be followed without serious diversion from projects already on the Survey's program. Brief reviews by Survey men have been published in periodicals, and the contributions by several of them to the Lindgren Volume1 may also be cited as serving this purpose to some degree. The practice of publishing short papers by Survey men in outside journals rather than in Government reports is largely the result of experience and expedience. Our printing funds are limited, and considerable time must elapse between the transmittal of a paper and its publication. Time is saved therefore by sending papers to outside journals, and the editors of those journals are usually glad to receive them. Members of the Survey would doubtless prefer to have the products and byproducts of their official work appear in official Survey publications if conditions were more favorable. If we were left entirely to ourselves the balance between the more scientific and the more directly practical studies would be somewhat better than it is, but the

Jan 1, 1935

W. H. Blauvelt, New York, N. Y.—One thought lias been running through my mind during the wholc of this meeting and that is that the scientific and the practical men must recognize very clearly their interdependence. The value of scientific classification of coal is going to be of the very greatest importance to the users, the practical men. Is not the scientific investigation and the great amount of work that is being done in a measure at least lost to the world? Therefore the scientific investigations and the practical needs of the users should bo brought as close together, and the work should be done as closely together, as possible; that is, the scientific man should know what the practical man needs, and the practical man should not feel that the scientific man is merely a theorist. Scientific investigation is going to have a great effeet and be of great valuc to the practical man who is trying to solve his problems. In the subject which I discussed' for instance, we must look to the scientific man to tell us why coal cokes in one way and not In another and why certain coals will do certain things and others, which appear on the surfacc to be generally similar, do not act in the same way. Need or Physical Data on Coal H. J. Rose, Pittsburgh, Pa.—There is a subject which is a sort of hobby of mine; that is, the need for what might be called critical tables of constants for coal. The chemist has big volumes giving constants, such as the density, solubility, specific heat, thermal conductivity and all other physical and chemical data that have been determined for chemical compounds. Data arc also available on many common materials, for example, the density, hardness, modulus of rupture or maximum crushing strength of swamp white oak as compared with some other wood. In fact, physical data for practically cvery hype of wood commercially produced in the world can he found. In the same way the metallurgical man has handbooks giving the properties of alloys, etc., but we havc very little tabulated information about coal. Our principal reference works are the volumes published by the U. S. Bureau of Mines on the proximatc and ultimate analysis and calorific values of coals of the United States. That is 3 pioncer work of enormous value, but we have reached the point where we need more diversified information. Mr. Fulweiler raised the question of the relative strength of the different coals and cokes. Dr. Campbell and Dr. Ashley wanted to have some information on the resistance of coal to air slacking. It was brought out in the discussion that we want to know something about the coking properties of coal. There are any number of physical tests that we need, such as the thermal conductivity of certain coals, the coefficient of expansion, or the coefficient of friction; or other constants. A smattering of such information is scattered through the literature; for instance, a research worker in Wales will report a coefficient of expansion on Wclsh coals and one in South Africa will report something else for one or two kinds of African coals, hut it is difficult to find the information that is needed on our own coals. Would it not be worth while to consider collecting reliable critical

Jan 1, 1930

By W. A. Backofen

THE texture of cold-drawn copper wire has been described most often as a composite of [Ill] and [loo] directions aligned parallel to the wire axis.' Hibbard2 suggested that sufficient reduction will result in a single [111] texture and reported that after a reduction in area of 96.4 pct, such a texture was nearly obtained. Other work3-4 has shown that recrystallization within the temperature range of 300" to 1000°C does not alter the texture established by cold-drawing. In general, however, the texture of cold-drawn end annealed copper wire is not as well defined as the deformation texture. In the work reported here it was found that the double-fiber, deformation texture persists even after a reduction in area of 97.3 pct, and after recrystallization the texture is practically all [l00]. The wire used in this work was prepared in the following way. A 3/4-in. diam length of annealed OFHC copper was cold-drawn to a diameter of 1/8 in., a reduction in area of 97.3 pct. Each step in the drawing operation brought about a reduction in area that varied from 6 to 10 pct. Short lengths of this wire were etched in a 50-pct solution of nitric acid to a diameter of approximately 0.01 in. The texture of the cold-drawn specimens was determined with the conventional X-ray transmission diffraction technique using filtered copper radiation. The X-ray beam was directed perpendicularly to the wire axis and the diffraction rings were recorded on a flat film. Fig. la is typical of the photo-grams obtained and reveals that the cold-drawing schedule described above introduces a distinct, double-fiber texture with both [Ill] and [l00] directions aligned parallel to the wire axis. Supplementary measurements with a Geiger-Mueller counter of the intensity of reflection from (111) planes showed that the [111] component was much more predominant than the [l00]. Additional specimens of the drawn and etched wire were annealed in a salt bath at temperatures from 300" to 450°C. The texture of the recrystal-lized wire was studied with the same technique applied to the cold-drawn wire. Fig. lb is an X-ray photogram of a specimen annealed for 1 ½ at 300°C and is typical of those obtained from re-crystallized specimens. The photogram shows that recrystallization of this material is accompanied by the almost complete elimination of the [111] component of the deformation texture. A pronounced strengthening of the [100] component was evident from intensity measurements with a Geiger-Mueller counter. In summary, the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [Ill] and [loo] directions aligned parallel to the wire axis. Recrystallization of such wire at temperatures from 300" to 450°C introduces a texture which consists almost entirely of a [loo] alignment. Acknowledgment Sidney Rolle of the Scomet Engineering Co. generously supplied the OFHC copper used in this work. References 'C. S. Barrett: Structure of Metals. p. 382 (1943) New York. McGraw-Hill Book Co. 2 W. R. Hibbard, Jr.: Trans. AIME (1949) -185, p. 598; Journal of Metals (Sept. 1949) TN 19E. 3 P. 422 of ref. 1. 'E. Schmid and G. Wasserman: Ztsch. Physik (1926) 40, p. 451.

Jan 1, 1952

By T. G. Nilan

Steels containing 0.4 and 0.8 pet C have been transformed isothermally at pressures up to 34 kbuv. Decomposilion mechanisms are so intimately related to phase equilibvia that, as the equilibria shift under high pressure, the microstruclures of the decomposition producls change, maintaining at pressure the same correspondence between a given phase equilibrium and a given microstructure as a1 1 atm. A bainitic unicvo-structure occurs in these steels at high pressure that IS observed only at 1 aim abole 1.4 pct C. This strrrcl111,e 1s ruliorzalized in terms of the effect of pressure on the transformation to lower bainite. The pressuve depetlderlce of the kinetics of pearlile formation is descrihed by an absolute rule theory amalysis. The activation volume for the transformation is 7 cu cm per mlole, which is indicative of a phase-interface transformation-rate cotntrol mechanism. This fortmulation, when expressed in terms of known solule effects on the energelics of tvansformation, gives promise of explaining the effects of alloying elemenls on hnrden-abilily, particularly that of 'coball. KINETIC processes in solids are functions of the primary thermodynamic variables of state: composition, temperature, and pressure. Until the development of high-pressure techniques' that permitted the generation of sustained high pressure at high temperatures, metallurgical studies of such reactions were largely limited to isobaric conditions at atmospheric pressure. The data so obtained, and theoretical deductions based on these data, were necessarily incomplete For the particular case of austenite decomposition, a knowledge of the phenomenology of the reaction in terms of all the state variables should lead to a clarification of the process. This deeper understanding should facilitate a decision between conflicting theories that have been proposed to rationalize these phe- nomena. An analysis, derived from an understanding of the transformation mechanisms, may aid in the optimization of alloy steel development. The first studies of the effect of pressure on transformations in steel were made by Kulin et al. in 1952.' In a study of the influence of applied stress on mar-tensite formation in a 30 pct Ni steel, they found that the martensite start (M,) was depressed 8°C per kbar* by hydrostatic pressure. Jellinghaus and Friedewold3 were apparently the first to investigate the effect of pressure on isothermal transformations above the Ms. They found that the bainite transformation rate in a 1.2 pct C, 3.8 pct Mn steel was reduced by a factor of 3 by a hydrostatic pressure of 4 kbar. In both of these investigations,2,3 the M, of the steels studied was below room temperature. Austenitizing and quenching were done at atmospheric pressure, followed by the decomposition of the metastable austenite under pressure. The maximum temperature at pressure in the bainite study3 was 350°C. Until the advent of the present high-pressure devices, it was not possible to conduct isobaric high-pressure heat treatments from austenitizing through isothermal decomposition and quenching. The exploitation of high pressure as a variable in metallurgical studies was greatly advanced by the apparatus and techniques developed by Hall4 and co-workers. Utilizing these techniques, Radcliffe et a1.5 and Hilliard6 etermined the pressure dependence of phase equilibria in the Fe-C system. Hilliard and cahn7 examined the pearlite transformation rate in an AISI 1080 steel and also in a high-purity 0.92 C Fe-C alloy at 1 atm and at 34 kbar and found a 700-fold reduction in rate at pressure in the 1080 steel but only a fivefold reduction in the high-purity alloy. In agreement with the shift of phase equilibria under pressure, the microstructures were hypereutectoid at 34 kbar pressure, whereas they are eutectoid at 1 atm. Determination of the effect of pressure on carbon diffu-

Jan 1, 1968

By William Johnson

IT is now recognized that several important types of reactions in metallic systems proceed by the formation of nuclei and the growth of these nuclei. The process of freezing is a simple example of this, as Tammann pointed out years ago.1 Tammann held that ' the rate, of freezing is determined by a rate of nucleation, expressed as the number of nuclei formed per unit volume of unfrozen liquid per second, and a rate of growth of these nuclei, expressed as the linear rate of radial growth in units of length per second. For isothermal freezing the conception is simple; for ordinary freezing, extending over a range of temperature, it is not as simple, for the values of the two constants must change with change in temperature. There is ample evidence that the postulated mechanism is correct even though a quantitative derivation of the rate of isothermal or of ordinary freezing in terms of the two constants has been lacking. In recent years other reactions have been found to proceed in a similar fashion. It has been well established, particularly by Bain,2-8 that. the formation of pearlite from the eutectoid decomposition of the solid solu-tion austenite proceeds in such a way, and Polanyi and Schmid, Tammann and Crone, Karnop and Sachs, and others9-11 have shown that the process of recrystallization proceeds in a similar way. Isothermal reaction rates have been determined for eutectoid decom-position by a number of investigators. Bain's2-8 work on the formation of pearlite from austenite is especially valuable in this respect-the type of isothermal reaction curve obtained, as illustrated in Fig. 13, showed an initial slow rate, accelerating to an intermediate maximum rate which then decelerated to the completion of the reaction; similar curves have been obtained by Wever and his collaborators.12 Other eutectoid decompositions show similar behavior: for example, the decomposition of the beta eutectoid in the copper-aluminum system, studied by Smith

Jan 1, 1939

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-' proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible 'References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By W. Bonfield

A study has been made of the dislocation substructures produced in hot-pressed beryllium specimens strained to various levels in the range from 800 x 10-6 In. pev in. to fracture. A number of distinctive dislocation configurations were observed in this region which had not been noted at lower levels of strain. These included dislocation-dislocation interactions to form networks, dislocation "walls", subgrain boundaries and complex arrays, interactions between dislocations and large beryllium oxide particles, and the generation of dislocations from certain particles. The nature of these differences in substructure and their relation to the stress-strain characteristics of polycrystalline beryllium are discussed. In a previous study1 of the plasticity of commercial-purity, hot-pressed beryllium a transition was found in the deformation characteristics in the mi-crostrain region. The initial plastic deformation could be represented by a parabolic stress-strain equation, but above a critical stress there was a complete departure from this relation and a reduction in the strain-hardening rate. The dislocation configurations produced by various levels of micro-strain in this region were examined by transmission electron microscopy and a general correlation was established between the observed transition in deformation characteristics and the dislocation structure of the material. The two stages in the micro-strain region distinguished in these experiments were designated as Stage A' and Stage B'. Stage A' type deformation generally was noted up to a plastic strain of -80 x 10"6 in. per in. and Stage B' type from -80 x 10-6 to -800 x 10'6 in. per in. The discovery of two stages in the microstrain region naturally posed pertinent questions as to the existence of any further distinct stages in the subsequent plastic deformation. The purpose of this paper is to present a study of the dislocation configurations produced in similar beryllium specimens strained to various levels in the range from -800 x 10 in. per in. to fracture and to discuss the relation between substructure and the stress-strain characteristics. It is concluded that this region of strain can be considered as a distinct stage in the plastic deformation of polycrystalline beryllium. Tensile specimens of gage length 1 in. and cross section 0.18 by 0.06 in. were prepared from commercial-purity, hot-pressed QMV beryllium and then annealed at 1100°C for 2 hr. 2 followed by a careful chemical polishing procedure.3 The specimens were strained at a constant rate to various levels of strain in the range from -800 x 10-6 in. per in. to fracture (at 0.5 to 2 pct elongation), using the Tuckerman strain-gage technique1 to measure plastic and total strain. Thin foils were obtained from the strained and fractured specimens by chemical polishing3 and were examined using an RCA-EMU 3 electron microscope. Considerable care waS taken to avoid both accidental deformation during the preparation of the thin foils and excessive heating during their examination. Selected-area diffraction patterns were determined for each micrograph. Tilting experiments were also performed whenever appropriate to establish the dislocation zero-contrast position and hence determine the Burgers vector. This operation was sometimes not possible due to the rapid contamination of the foils which occurred in the electron microscope. RESULTS AND DISCUSSION To enable the distinctions between the dislocation arrays at high and low strain levels to be adequately made, the main characteristics of Stage A' and Stage B' deformation are briefly reviewed. 1) Stage A'. In the annealed starting condition there was a variable density (5 x 107 to 3 x 10' cm per cu cm) of isolated dislocations within a grain. The initial deformation in a tensile specimen was heterogeneous, with the dislocation density increasing in a few grains to 5 x 10g to 1.5 x 101° cm per cu cm. The deformation occurred exclusively on the basal plane by the movement of one or more 1/3 (1130) type dislocation systems. The dislocations were long and regular in form and nearly all the intersections exhibited a simple four-point node configuration. No interactions between glide dislocations and beryllium oxide particles were observed. 2) Stage B. In Stage B' there was a large increase in the number of grains exhibiting dislocation movement and also a change in the nature of the deformation, in which jogged dislocations and elongated loops became the characteristic feature. The splitting up of the elongated loops into smaller loops and the possibility of source action from the re-

Jan 1, 1965

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By P. C. Johnson, B. A. Stein

This paper describes a study of the effects of combined heat treatment and explosive loading on the mechanical properties of high-strength steels. nis program investigated two distinct areas: 1) the effect of shock waves, without gross irreversible defmmution, on a 3-Cr steel at various stages of heat treatment; and 2) the effect of rapid deformation (explosive forming) on H-11 and D6-AC steels in the metastable austenitic state. The mechanical properties of these steels were improved, in some cases markedly, as a result of these treatments. ,AUSFORMWG, which requires the plastic deformation of metastable austenite, is a process which can appreciably improve the properties of selected alloy stee1s.l,2 The Ausform process significantly increases the strength of these steels without decreasing their ductility. The properties at high temperatures are also improved through a change in the response of the steels to tempering. Although the mechanism by which ausforming alters the properties of these steels is not fully understood, it appears that the dislocation arrays produced by deformation of the metastable austenite influence the structure of the martensite on subsequent transformation. This, in turn, affects the strength, ductility, and tempering response of the martensite. This research used chemical explosives to deform steels at various stages in their heat treatment in order to improve the properties of these steels. The explosive energy is used in two ways; 1) high-pressure shock waves are propagated through the steel to produce extensive microscopic shear strain without causing a large irreversible change in shape, and 2) explosive energy is used to cause extensive macroscopic plastic strain in the metastable austenitic state (explosive forming). I) AUSFORMING WITH INTENSE SHOCK WAVES The steel used in this phase of the research was an alloy having a nominal composition 0.43 pct C, 3.0 pct Cr, 1.5 pct Ni, and 1.5 pct Si. The steel was subjected to intense shock waves in three conditions: 1) in the metastable austenitic state, 2) in the tempered mar tens itic state, and 3) in the tempered martensitic state after ausforming by conventional techniques. The specimens were in the form of disks 2.75 in. in diam and 5/16 in. thick. These were incorporated into a specimen assembly consisting of two disks pressed into a 5 by 5 by 1 in. block of stainless steel, Fig. 1. Spalling (or scabbing) is confined to the front disk. The specimen is protected from oxidation and decarburization by the surrounding metal. The temperature of the assembly is monitored by a thermocouple inserted into one side of the stainless steel block. The assembly is positioned over an oil reservoir which serves both as a means of catching the disks and as quenching medium for the disks shocked under ausforming conditions. Plane shock waves are introduced into the assembly by a metal driver plate impacting the top surface of the block. The driver plate is accelerated by a chemical explosive sheet supplied by E. I. du Pont de Nemours & Co. All the specimens were subjected to plane shock waves having a peak pressure of approximately 430 kbar. The pressure is that quoted by G. E. Dieter for the plane wave generator used in this work.' The driver plate used was 1/4 in. thick, so that the initial pulse was essentially a l/2-in.-wide square wave. The attenuation of the peak pressure during the subsequent 1/4 in. is estimated to be less than 5 pct. The shock front induces a temperature rise, a portion of which is irreversible. Rough estimates (+25 pct) of this temperature rise have been made for iron shocked at room temperature.4 For a 500-kbar shock wave, the temperature rise in the shock front is about 700°F, and is held for a time of the order of microseconds. The irreversible temperature rise, which remains after the shock wave passes, is about 450°F.4 The disks are quenched to room temperature within a few seconds of the shock treatment. It should be emphasized that the temperature rises given above are estimates for pure iron at room temperature, and are not necessarily true for the tests made in this work. The disks shocked at temperatures in the metastable austenitic range were austenitized in the stainless steel assembly in a furnace protected from the firing area. The assembly was removed from the furnace and placed over the recovery reservoir. The plane wave generator was then positioned and

Jan 1, 1963

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nev. The supporting laboratory investigations were made at the Bureau's Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45' to a slope angle that started at 45° on the south wall, and gradually increased to 575' at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 ft to about 550 ft. About 2.55 million tons of waste and ore were removed by stripping and mining. Measurements made between November 1965 and September 1967 showed that the pit wall was stable before excavation began, that changes in the measured quantities occurred in the pit wall during the excavation, and that the wall returned to a condition of equilibrium after the mining was completed. The need for a method and the technology to pre-design a pit slope does not require elaboration. About 5 billion tons of material are excavated yearly by surface mining methods in the United States, and the economics, safety, and availability of lower grade metals, nonmetals and fuels could all be substantially improved if operators could preselect optimum slope angles. Mining companies and the Bureau of Mines have recognized the need for developing engineering methods to determine stable slope angles. In the industry, Kennecott Copper Corp. had been making an

Jan 1, 1969

By J. J. Frawley, W. J. Childs, W. R. Maurer

The object of this investigation was to determine the growth habit of bismuth and bisrrtuth alloy dendrites as a function of supercooling. To do this, techniques were developed to increase the amount of supercooling in bismuth and bismuth alloys. For pure bismuth, the growth habit was dependent on the amount of supercooling. At low amounts of supercooling, about 10" C, prismatic dendrites were obtained. With increased supercooling, about 20 C, a hopper growth habit was observed. In many cases where hopper growth had occurred, the hopper dendrites were twinned during the growth process. This twinned surface enable prismatic dendrites to nucleate and grow by a twin plane mechanism. When the amount of supercooling was increased to about 25 °C, the growth habit was a triplanar growth. With still greater supercooling, about 3s°C, a branched growth habit occurred. The exposed planes on the prismatic, hopper,, triplane, and branched dendrites have been determined. The growth habit of the dendrites which grew along the crucible wall was found to have the (111) as the exposed plane, with <211> growth direction. It is apparent that dendritic growth of a metal is dependent on its purity and the solidification variables present. One of the solidification variables is the degree of supercooling. Supercooling, although often observed, has not been studied extensively until recent years. For dendritic growth to occur in a pure metal, the metal must be thermally supercooled. After the dendrites grow into the supercooled melt, the heat of solidification raises the temperature of the specimen to the melting point of the material and the remaining liquid will solidify at this temperature. Decanting is the removal of this remaining liquid before complete solidification. This removal of the remaining liquid after recalescence had occurred is a great aid in the study of dendritic growth. In this investigation, decanting was accomplished by a vacuum-decanting technique . Other investigators1-5 have studied the growth characteristics of various low-melting-temperature pure metals and alloys as a function of supercooling. However, large degrees of supercooling were not included. For their study of dendritic growth of lead, Weinberg and chalmersl employed a decanting technique which was achieved by pouring off the remaining liquid, exposing the solid/liquid interface. This method was employed later by Weinberg and Chalmers2 for the investigation of tin and zinc dendrites. The method for obtaining a solid/liquid interface was improved by Chalmers and Elbaum. They employed a triggered spring which was attached to the solidifying section of the specimen. Upon activation, the spring jerked the solid interface away from the liquid melt. In the study of growth from the supercooled state, a metal of low melting point which exhibited a high degree of supercooling was desired. Bismuth gave very consistent supercooling when a stannous chloride flux was employed. The maximum supercooling obtained was 91°C, with an average supercooling of between 65" and 75°C. The consistency of supercooling greater than 50°C was very high. The use of vacuum to aid in the rapid decanting of molten metal has proven to be very successful in this investigation. The vacuum gives a rapid decantation, usually leaving the solidified metal structure sharply defined. The purpose of this investigation was to study the effects of supercooling and the effects of alloy additions on the growth habit of bismuth dendrites. The structure of bismuth has been variously defined as face-centered rhombohedral, primitive rhombohedral, and hexagonal. However, bismuth has only one plane with threefold symmetry, the (111) plane, and the crystal-lographic structure is considered a 3kn structure. MATERIALS The bismuth which was employed in this investigation was obtained from the American Smelting and Refining Co. of South Plainfield, N. J. The accompanying spectrographic analysis data indicated the bismuth to be 99.999+ pct pure. The tin was obtained from the Vulcan Materials Co., Vulcan Detinning Division, Sewaren, N. J. It was classified as "extra pure". Nominal analysis was 99.999+pct. In order to prevent contamination of the bismuth melt from the atmosphere, an anhydrous stannous chloride (Fisher certified reagent grade) was added to each melt. The fluxing action obtained from the use of the chloride provided a large amount of supercooling in the specimen. APPARATUS A 30-kw, 10,000-cps motor-generator set, connected to a 6+-in.-diam air induction coil, was employed to melt and superheat the specimens. The temperatures were recorded by means of a chromel-alumel thermocouple and a potentiometric recorder. The thermocouples were 0.003 in. in diam, and were encapsulated with Pyrex glass to prevent the thermocouple from acting as a nucleating agent and also from contaminating the melt. Fig. 1 illustrates the vacuum-decanting apparatus when a liquid flux was employed. A standard 30-ml Pyrex beaker was placed on top of an asbestos insulating block. A 5-mm-ID Pyrex tube with aA-in. spacer tip attached to its end was used for the decanting tube. The spacer tip contributed significantly to a successful decanting operation. The tip located the opening of the decanting tube about -^ in. from the bottom of the

Jan 1, 1969