Search Documents

By Nicholas J. Grant, Laszlo J. Bonis

Two dilute nickel alloys in each of the systems Ni-Al, Ni-Ti, Ni-Cr, and Ni-Si u:ere internally oxidized at 700° to 900°C for time periods up to 100hr to establish the oxide particle size, depth of oxide penetration, and the change in oxide particle size with depth. Fine (-270) mesh alloy powders were then intevruzlly oxidized, hydrogen sintered, compacted, and extrmded, yielding bar stock for tensile tests at room temperature and creep-mpture tests at 815° to 1093°C. Recrystallization studies were made up to 1400OC. ReCENT studies have clearly indicated that oxide dispersion strengthened alloys exhibit outstanding elevated temperature properties, espe- cially in long-time tests. Certain structural parameters must be observed to achieve optimum properties, namely, micron or submicron interpar-ticle spacing, submicron oxide particle size, and a high level of stored energy.'-5 A number of processes have been utilized to obtain the desired structures, but certain of them appear to offer greater promise. Thus far the most promising method is the internal oxidation of dilute alloys consisting of a relatively noble solvent metal and a readily oxidizable solute element.3'6)7 Several important principles governing internal oxidation have been established in earlier studies;' however, these principles are as yet not adequate to permit alloy development studies. Much of the earlier work was performed on relatively coarse wires or in idealized systems. As a result, there are still a number of unanswered questions which require considerable additional work: a) How does oxide particle size change with depth of penetration of the oxide? How does this vary with the specific type of solute element? b) What is the effect of solute content on the average oxide particle size?

Jan 1, 1962

By John Chipman, Helen Towers

DEVELOPMENT of a simple radioactive tracer technique for measurement of the diffusion coefficient of calcium ion in liquid slag has already been reported. The investigation was of a preliminary nature designed to explore the possibilities of using radioactive isotopes and to establish a method, and no great accuracy was claimed for the results. It was shown, however, that Ca15 could be used successfully, and the values obtained for the diffusion coefficient appeared to be of the right order of magnitude. However, it was considered that a better technique could be devised for carrying out the diffusion. The experiments were, therefore, continued to find a more accurate method, to check the calcium results, and to extend the investigation to include measurements of the diffusion coefficient of silicon in the same slag. There were two flaws in the original technique. Convection was the cause of too many failures, and the interface between the two slags in the diffusion cell was curved rather than plane, probably due to a surface tension effect caused by the addition of the tracer Ca45 in the form of chloride. Two methods of overcoming these defects were tried. Since it was planned to study diffusion of the short-lived isotope Si"' also, the development of methods was restricted to those which gave promise of being reasonably rapid. Method 1—The principle was identical to that previously used with respect to the diffusion conditions, but there were three differences in technique. Temperature control was more rigid, the tracer was added to the slag as Ca45O rather than the chloride and, finally, an effort was made to translate to high temperatures the elegant method developed by Cohen and BruinV or bringing together the two liquid layers and beginning the diffusion. A master slag was melted in graphite, ground to a fine powder, and analyzed (38.5 pct Ca0-20.9 pct Al2O3-40.5 pct SiO2). The tracer was received as Ca45C12 in an aqueous solution of CaC12 + HC1. From this, calcium oxalate was precipitated, ignited to calcium oxide, and added as such to the slag to give an activity of approximately 5 µc per g. The mixture was then melted into the form of a cylinder 3/16 in. diam and about 1 in. long. A solution identical to the tracer solution without Ca45 was given exactly the same treatment. The resulting Ca40O was mixed with that slag which was to form the tracer-free half of the diffusion cell, and this was likewise melted into a cylinder of the same size. Slag cylinders, two with and two without Ca15, were set in graphite blocks as shown in Fig. 1, and the crucible was lowered into position in the fur-

Jan 1, 1958

By S. S. Lau

The authors of the previous comment stated that Dorn and Rajnak33 and others34-40 concluded that "agreement with this function [(t'/tp) -f(Un/2Un) = T/Tc} may be used as a criterion for that (the Peierls) mechanism of deformation". In contrast, however, Dorn and Rajnak33 and others34-40 never made such a statement. In order to clarify the issues involved it is appropriate to recapitulate the conditions that must be satisfied in order to suggest that some deformation process might obey the Peierls mechanism: 1) Within permissible variations due to changes in the slope of the Peierls hill the T*/Tp - T/Tc relationship must be obeyed. Although some mechanisms, e.g.. solute atom stress field, recombination of dissociated partials in bcc metals, intersection of dissociated dislocations, and so forth, give about the same t* - T relationship, other mechanisms, such as cross slip, disruption of attractive junctions, climb, motion of jogged screw dislocations, and so forth, give distinctly different t*-T relationships. On this basis some distinction can be made of the various mechanisms. 2) An important feature of the Peierls mechanism concerns its physical origin based on the nucleation of pairs of kinks. The value of T* at 0°K increases with the density of dislocation (i.e. , cold work) for the intersection mechanism and it increases with the square root of the atomic fraction of solute atoms in the solute atom interaction mechanism. In contrast the value of t* at 0°k, for the Peierls mechanism which depends only on the line energy and the shape of the Peierls hills. is independent of cold working and the square root of the solute atom concentration. These differences have been employed by various investigators for elimination of a few other possible mechanisms. On the other hand it is not possible to eliminate all mechanisms, e.g., the recombination of dissociated dislocations in bcc metals, and so forth, on this basis alone. 3) Further discrimination between possible mechanisms is based on the activation volume. For the in-

Jan 1, 1968

By M. B. Yung

Location THE Fu Chuan district lies near the eastern boundary of Kwang Si province in southern China and is connected with the coast by the West river and its branches. The Journey The first part of the journey from the coast is made very comfortably in one of the West river steamers which runs to Wuchow, the great distributing center for tile whole province. From here there are two ways of reaching the Fu Chuan district. One is to drop clown the West river for 15 miles and ascend the Yuen river for 120 miles. The other is to ascend the Fu river, which joins the West river at Wuchow, and at Ping Lok tike chairs across country. Of the two the former is the more direct and shorter but for other reasons I chose the latter. At Wuchow one must provide his own means of transportation, which may be a native boat anywhere up to 40 ft. in length, but not over 18-in. draft. The method of working these river boats against the swift current which in many places develops into rapids is interesting and worthy of note. Tracking along the bank with the tow line attached to the mast head is the most common procedure, but poling, sculling, sailing and winding up the rapids by a windlass are used as the case may require. The boatmen are the hardiest set of fellows I have ever seen often putting in 15 hr. of the most exhausting labor. The average clay's run against the current is 15 miles. On this trip one should have his own food, bedding and servants, and a guard of 10, or more soldiers is almost a necessity as certain parts of the river are infested with pirates.

Jan 9, 1914

By B. D. Cullity

AS methods for measuring fiber textures become more exact, it becomes justifiable to scrutinize an observed pole-density curve for evidence of minor texture components. These are disclosed by minor maxima or abnormally broad major maxima. One possible source of these minor components is twinning of the main component. In cubic metals and alloys, there are two kinds of twins: 1) Annealing twins in face-centered cubic metals. These are reflection twins on {Ill), and they can be expected to be present in recrystallization textures. 2) Deformation twins in body-centered cubic metals. These are shear twins on (112). Although usually formed only by impact, they might conceivably be present in the deformation texture of severely cold-drawn wire. Fortunately, both kinds of twinning lead to the same orientation relationships. It thus becomes possible to prepare a single list of angles between various planes in parent crystal and twin, which is helpful in examining pole-density curves for evidence of twinning in any cubic metal or alloy. Such a list of interplanar angles is given in Table I. This table consists of three parts, corresponding to the three major texture components—<100>, <110>, and <111>-most commonly found in the fiber textures of cubic metals. The table lists the angle between the pole of {hkl}, in either the parent crystal P or the twin T, and the fiber axis <uvu>. The crystals with <uvw> parallel to the wire axis are here

Jan 1, 1959

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,&apos; but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By R. B. Campbell

One of the three power plants that will be in the Curecanti Unit of the Bureau of Reclamation&apos;s Colorado River Storage Project is the power plant at Morrow Point Dam. Presently under construction, the Morrow Point Power Plant is between Gunnison and Montrose on the Gunnison River in west-central Colorado. (Fig. 1). Morrow Point Dam will be a thin, double-curvature, concrete-arch dam, 465 ft high and will impound 120,000 acre-ft of water. Two 60,000-kw hydroelectric generators will be housed in an underground power plant in the left abutment just down- stream from the dam. The power-plant chamber will be an unlined opening 205.5 ft long, 57 ft wide and 65 to 134 ft high. The arch-type roof with a rise-to-span ratio of 1 to 4 will be supported with rock bolts and chain link fence. A description and discussion of the design considerations for the power-plant opening and rock bolt design are given by William H. Wolf, Gilbert L. Brown, and Ernest D. Morgan in "Morrow Point Under- ground Powerplant," ASCE Power Division Specialty Conference, Denver Colorado, August 18-20, 1965. The Morrow Point site is in a moderately active region of mild earth- quakes, as evidenced by recent earthquakes in 1960 and 1962. Therefore, the Bureau of Reclamation undertook an investigation of the effects on the underground power-plant chamber when subjected to an earthquake. The art of earthquake engineering has been directed primarily at developing methods of analyzing the nature of ground surface motions and designing surface structures to resist damage from vibrations impressed on the structure by the ground motions. The mechanism of straining an underground cavity by an earthquake

Jan 1, 1968

By A. C. Emery

The physical and chemical properties for the metalliferrous feed materials to the Imperial Smelting Process blast furnace are defined and the means of achieving these properties by the sintering or briquetting routes discussed. Modern sinter plant performance data is included with a plant flow sheet showing draughting patterns. The necessity for ensuring an adequate SO2 content in sinter machine gases when roasting sulphide materials to enable conversion to sulphuric acid in a contact acid plant is described. The ability of the process to consume limited quantities of oxide materials, residues from other processes and other secondary sources is discussed. The argument for a briquetting route is developed out of this limitation and the merits of cold and hot briquetting examined. Development work on the hot briquetting route for this purpose is briefly described and several flow sheets outlining possible applications for hot briquetting to different raw material situations including the preparation of low lead charges for the furnace are presented.

Jan 1, 1977

By Frederick N. Rhines, Robert F. Mehl

Relatively few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZnz, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.* Fundamentally, methods for the determination of the state of molecular aggregation in solution depend upon the kinetic behavior of the particles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecular solid solution would be afforded. Freche5 examined the rates of

Jan 1, 1940

By Frederick N. Rhines, Robert F. Mehl

Relatively few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZnz, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.* Fundamentally, methods for the determination of the state of molecular aggregation in solution depend upon the kinetic behavior of the particles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecular solid solution would be afforded. Freche5 examined the rates of

Jan 1, 1940

By A. R. Denison

The Permian Basin as it appears in the title of this article refers to three rather widely separated areas of production. It includes what are commonly known as the "Panhandle" fields of the northwest part of Texas; the West Texas fields, in the southwest part of Texas; and the New Mexico fields, in the southeast corner of New Mexico. These three areas are all included in a single province and produce the majority of their oil from limestones or dolomites of Permian age. The manner of accumulation of oil in the three areas is somewhat diverse. In the Panhandle, production is found on the flanks of an enormous structural ridge, the core of which is granite. In southwest Texas and New Mexico oil is produced from both gentle and steep folds and from lenticular areas of porosity. Production in Texas During 1927 Texas produced a total of 216,306,000 bbl. of oil of which the Permian Basin contributed 89,797,000 bbl., or 42 per cent. During 1928, Texas produced 255,021,000 bbl. of oil of which the Permian Basin contributed 145,955,000 bbl., or 57 per cent. The increase in total production is entirely due to the West Texas fields. All other districts in Texas declined during the year while the west Texas fields registered an increase of more than 71,000,000 bbl. West Texas daily average production increased from 260,752 bbl, at the beginning of 1928 to a maximum of 406,318 bbl. per day the first week in May. Due to prora-tion agreements, the production was held at a fairly constant level around 340,000 bbl. during the remainder of the year, having 345,660 bbl. the last week in December. Daily average production of the Panhandle fields decreased from 80,178 bbl. at the beginning of the year to 59,025 bbl. at the close of the year. The combined daily average production of the Panhandle and West Texas fields at the beginning of the year was 341,138 bbl. and at the close of the year was 405,408 barrels. Fig. 1 gives a comparison of the production in the Permian Basin in relation to the production of the entire state. It is clearly shown that

Jan 1, 1929

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman&apos; reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser&apos; reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,&apos; values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,&apos; on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.&apos; When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By H. F. Silliman, Daniel R. Hull, John R. Freeman

In the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of cold-work and a considerable number of anneals. This condition has been disturbed by the preponderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2:r brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. Hot-rolled 2:1 Brass For illustration, therefore, a typical cake of hot-rolled 2:I brass has been chosen. This was rolled to a slab 36 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. I. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it would be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By W. S. McCain, B. A. Wilcox, A. H. Clauer

The creep and creep-fracture behavior of a Ni-200-2Th0, alloy has been studied over the temperature range 816° to 1038°C and stress range 4000 to 19,000 psi Specimens having their axes either parallel or transverse to the final sheet-rolling direction were tested in air, and the apparent activation energy for creep was found to be 92 kcal per mole, regardless of specinien orientation. The stress dependence 01- the steady-state creep rate, was satisfied by where n depended on orientation; n = 9.7 for rrzaterial transverse to the rolling direction and n = 24.3 for material parallel to the rolling direction. In the latter case, the relation was also valid. The rupture strength of material parallel to the rolling direction was -1.5 times gveater than the transverse rupture strength. Several tests in vacuum revealed that here the creep rate was higher and rupture life lower than for comparable tests in air. THERE is an increased interest today in producing improved dispersion-hardened alloys for high-temperature structural applications. This had led various materials designers to modify existing alloys, such as thoriated nickel. One system that has received considerable attention is based on chromium additions to Ni-ThO2, with the obvious motive of improving the oxidation resistance. Another effect of chromium is that of lowering the stacking-fault energy, y, of nickel. For example, the addition of 30 wt pct Cr decreases y from -225 erg per sq cm for pure nickel1 to -70 erg per sq cm.&apos; This decrease in y could have several effects on the deformation behavior. There is some evidence that cross slip of dislocations around Tho2 particles is a mechanism of tensile3 and creep4 deformation in TD Nickel (Ni + 2 vol pct ThO2) at temperatures below 0.5 the absolute melting point of nickel, T,. A decrease in ? by chromium additions should increase the difficulty of cross slip. Also it has been suggested that the high-temperature (T > 0.5Tm) rate-controlling creep process in "recrystallized" Ni-Tho2 alloys is the climb of edge dislocations over Tho2 particles.5 According to weertman6 a decrease in the stacking-fault energy should decrease the dislocation climb velocity resulting in a decreased steady-state creep rate. Thus, chromium additions to recrystallized Ni-Tho2 alloys would be expected to decrease the creep rate, all other conditions being constant. However, a difficulty arises when the stacking-fault concept is applied to high-temperature creep of dispersion-strengthened metals which are produced on a commercial or semicommercial scale. This occurs because the materials are processed so that they have a high-stored energy of cold work, and the other substructural effects could obscure any influence of stacking-fault energy per se. An example of an alloy with a high stored energy of cold work is TD Nickel bar. This material has a fibrous grain structure (1 I diam by 10 to 15 p long), and the structure is stabilized by the ThO2 particles. Annealing at high temperatures, e.g., 3 hr at 1300°C, causes no recrystallization or grain growth.4 Previous work by the authors4 showed that the high -temperature creep behavior of TD Nickel could not be related to any simple dislocation theory of creep, and this probably was associated with the complex initial structure of the material.

Jan 1, 1968

By J. A. Herbst, D. W. Fuerstenau

The effect of mill speed and ball load on the dry ball milling of dolomite is examined in the context of the batch grinding model. Observed changes in the parameters of the model are interpreted, as far as possible, in terms of the mechanics of particle motion in the mill. A parameter estimation scheme previously proposed by the authors is shown to provide the basis for a successful simulation of grinding behavior over a wide range of mill speeds and ball loads. Finally, a combination of experimental and simulated results is used to determine the optimum mill speedball load for closed circuit grinding in this mill-material system.

Jan 1, 1973

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders&apos; Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.1 Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period 0f approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. Vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the system could be degassed thoroughly in

Jan 1, 1948

By Robert E. Thurmond, E. D. Spaulding, Walter E. Heinrichs

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development.

Jan 2, 1954

By Samuel G. Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change. Outline of Kennecott Mines Geology The mines at Kennecott are on the northeast flank of a broad anticlinell where erosion has exposed the Upper Triassic Chitistone limestone resting conformably on the Permian or Triassic Nikolai greenstone.2 These two are the only formations exposed in the immediate vicinity of the mines that bear relation to the ore deposits. The Nikolai greenstone is a series of altered basaltic lava flows, the actual thickness of which is unknown. The Chitistone limestone is the ore-bearing formation. At its base is a bed of about 5 ft. of red, green, or black shale which shows strong evidence of movement wherever it is exposed underground—one of the

Jan 1, 1929

By T. E. Leontis

Data are presented in this paper to show that addition of zirconium to sand-cast Mg-Th alloys effects a marked decrease in the grain size of these alloys which is accompanied by a significant increase in the mechanical properties over the entire range of thorium content investigated. The beneficial effect of zirconium on the strength properties is maintained at elevated temperatures up to 700°F. In addition the alloys exhibit exceptionally high creep resistance at temperatures up to 600°F. Zirconium does not greatly improve the strength or creep characteristics of extruded Mg-&apos;Th alloys. Cerium is not a desirable addition to Mg-Th-Zr alloys. IN a previous paper,&apos; it was shown that addition of thorium to magnesium imparts exceptionally high resistance to creep at elevated temperatures both in the sand-cast and in the extruded states. The large grain size of the sand-cast alloys, however, renders them of questionable value as engineering materials. Sauerwald² showed that the grain size can be reduced effectively by the addition of zirconium. Results of a detailed study of the properties of Mg-Th-Zr alloys over a wide range of thorium content are presented in this paper. In accordance with the preliminary findings of Sauerwald,² it is shown here that Mg-Th-Zr alloys possess the unusual combination of fine grain size and a high level of strength and creep resistance at elevated temperatures. Some information on the effect of cerium on the properties of Mg-Th-Zr alloys is presented also. Effect of Th on Solubility of Zr in Molten Mg Sand-cast test bars and 3 in. diam extrusion billets of Mg-Th-Zr and Mg-Th-Ce-Zr alloys* were pre- pared according to the procedures described in the previous paper.&apos; The zirconium was added in the form of sponge metal as supplied by the Bureau of Mines.&apos; The maximum amount of zirconium that usually can be introduced into magnesium at the customary alloying temperature of 1350° F is about 0.7 pct. The analyses in Table I clearly show that thorium in- creases the solubility of zirconium in liquid magnesium. The tabulated zirconium contents are designated as "acid soluble;" this serves to distinguish these values from the small amount of zirconium that is not dissolved when the alloy is subjected to the action of a dilute acid solution. The "acid-insoluble" zirconium is believed to be ineffective as an alloying ingredient. The acid-insoluble zirconium contents ranged between 0.03 and 0.16 pct in the present alloys, the tendency was toward higher values in alloys with higher thorium content. In contrast to the effect of thorium, cerium decreases the solubility of zirconium in magnesium. This is shown by the three Mg-Th-Ce-Zr alloyst in- cluded in Table I and stands in agreement with the observations of Nelson and Stricter".&apos; on Mg-misch-metal-Zr alloys. Effect of Zr on Grain Size of Mg-Th Alloys The potent effect of zirconium as a grain refiner has been demonstrated for many types of magnesium alloys.3-8 Of greatest importance to date are Mg-Zn-Zr alloys5,6,8 and Mg-mischmetal-Zr alloys.3,4,7 Zirconium has also been found to exert a marked grain-refining action on Mg-Th alloys. All the Mg-Th-Zr alloys cast in the form of ½ in. diam test bars have an exceedingly fine grain size (Table I). Reference to the previous paper&apos; will show that binary Mg-Th alloys containing up to 6 pct Th are almost completely columnar even in the M in. diam reduced section of a test bar, and that 10 to 50 pct Th alloys have an equiaxed grain structure of 0.03 to 0.08 in. The data in Table I also show that addition of cerium to Mg-Th-Zr alloys has no effect on the grain size. In addition to increasing the strength properties, the fine grain size of Mg-Th-Zr alloys

Jan 1, 1953

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella&apos;s etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965