Search Documents

By W. Rostoker

A STUDY of the titanium-oxygen system' involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich's work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich's2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

By Stuart St. Clair

In view of the great interest shown in the oil possibilities of Kentucky, one is impressed with the paucity of reliable literature on the oil fields of the state. A few brief reports by the Federal and State Geological Surveys are about the only reliable data available. When the estimated production figures, for 1918, are published by the U. S. Geological Survey, they will show a revival of the oil industry in the Blue Grass State during the past half decade. There will also be an increase in the production for 1919 and 1920, at least. Although as an oil-producing state Kentucky is small, compared with some of the other oil states, the present production and the area of undrilled proved territory is large enough to classify it as one of the important oil states of the Union. This paper will be confined to the Irvine District and the immediately adjoining areas which have been prospected with varying success. The Corniferous limestone or Irvine sand is the oil-producing formation in the area discussed. In my divisional nomenclature, the Irvine District includes the Irvine field, which extends from the town of Irvine eastward toward Campton; the Big Sinking area, which joins and lies to the south of the eastern part of the Irvine field; the Beattyville area, which lies to the north and northeast of the town of that name and joins the Big Sinking area; and the Ross Creek pool, which lies to the southwest of the big production and across the Kentucky River. Except for the Ross Creek pool, the main producing area is bounded on the east by the L. & E. R. R. and on the west and south by the Irvine Branch of the L. & N. R. R. Winchester and Lexington form the gateways and Torrent on the east, Irvine on the west, and Beattyville on the south are the principle entrances to the main fields. Evelyn, on the L. & N. R. R., south of Irvine, is the point of entrance to the Ross Creek area. Geology The geology of the Irvine District is very simple. The rock formations with which the oil man should acquaint himself lie between the lower measures of the Pennsylvanian sandstones and shales and the Devonian or Corniferous limestone, or Irvine formation. Only a very brief description of these formations will be given, as they have been described fully by E. W. Shaw.'

Jan 1, 1921

By Thomas A. Simpson

THE Birmingham red iron ore district in Jeffer-son County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons.' The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation's total annual production,' and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country. Most of the mining in the Birmingham district is from slope mines along the outcrop of the ore on Red Mountain, such as Red Ore, Muscoda, Spaul- ding, and Sloss. The Pyne and the Shannon are the shaft mines of the area. The Shannon mine of Republic Steel Corp., in the central part of the area under study, is in Shades Valley at the foot of Shades Mountain. The Pyne mine of Woodward Iron Co. is 2 miles east of Readers Gap in Shades Valley. The hydrology problem has become more prevalent as mining in the area has progressed downdip. An extensive exploratory diamond drilling program is necessary to determine areas where water pressures and abnormal flows are excessive. This operation, added to higher pumpage rates, has greatly increased the costs of ore extraction. In November 1952 the U. S. Geological Survey began a detailed study of occurrence and movement of ground water in the iron mining areas of the Birmingham district. The study is a part of a small-scale but nationwide program to develop data that will be of help to the mining industry in solving mine water problems. The area of the study, in the Ridge and Valley province of the Appalachian system, Fig. 1, is a series of alternate ridges and valleys trending northeast. The principal ridges are Red Mountain, altitude about 1000 ft, and Shades Mountain, about 1100 ft. Shades Valley is between these two ridges, and its lowest point is about 480 ft. Shades Moun-

Jan 1, 1956

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By W. F. Mattes

The manufacture of steel rails in the United States upon a large scale may be roughly dated from the years 1875-76, and the same years witnessed an active movement among the railroads toward the adoption of heavier and improved patterns. In this movement each road was a law unto itself, and the "personal equations " of some scores of engineers were so freely injected into the calculations that patterns were multiplied in the most absurd and mischievous manner, until at length the burden upon the mills became wellnigh unendurable, and called forth a vigorous protest in Mr. Holley's paper,* read before the Institute in February, 1881. There were then regularly manufactured in the various mills of the United States, no less than 119 different patterns of steel rails, subject to current order, of which 64 per cent. were embraced under five weights per yard. Commenting upon these and other figures there given, Mr. Holley stated as the primary object of his paper, " to show that,, while this multiplication of rail-patterns is an annoyance and an expense to rail-makers, it is a source of immense loss to railway companies." Since 1876 the increase in gross annual tonnage upon our leading lines has been very great, and has been accompanied by an increase of wheel-loads and running-speeds. As the average weight of the rails of 1876 was by no means excessive, the growing deman Is of traffic have slowly driven the roads toward stiffer sections, inaugurating a movement that now promises to become epidemic. In 1876 a 67-pound rail was a first-class equipment; to-day everything under 75 pounds is light, and many 80's are coming into use. European practice has long been heavier than ours; in part because the higher cost of sleepers has led to an average of 3-feet spacing, instead of two-feet as with us. The old 84-pound double-header, and Sandberg's 80- and 89-pound rails, respectively 51/4 inches and 591/2 inches high, are reported common on English roads; and he is strongly advocating the general adoption of the 100-pounder shown in Fig. 7, with what success I have not learned, except that the Belgian government has ordered a lot. Mr. Sandberg points out the undesirability of frequent changes of pattern, and the recent rapid growth in traffic-requirements; prognosticates a continuance of this

Jan 1, 1887

By Charles S. Robinson

The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains, about 80 km (50 miles) west of Denver. The ore body is being developed for mining by workings that extend more than 1100 m (3500 ft) below the topographic surface. During construction of the mine workings, ground water in fractures in cystalline rock has been encountered. From 1969 to 1973, Charles S. Robinson & Associates, Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic record( of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentary rock and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past. Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreases with time. The rate of decrease in flow (or pressure) is exponential. By measuring the change in flow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 1, 1979

By Charles S. Robinson

Abstract-The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains, about 80 km (50 miles) west of Denver. The ore body is being developed for mining by workings that extend more than 1100 m (3500 ft) below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson B Associates Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentay rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreases with time. The rate of decrease inflow (or pressure) is exponential. By measuring the change inflow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 8, 1978

By Ernest Klepetko

A NOTABLE amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: [Specific gravity (melted) 1.03 -1. o6 Acid number6-8 Softening point, mercury method 160 -165°C Iodine value (Wijs)140-1.50 Refractive index1.544 Color (Hellige, 25 pct toluol) ...14 Molecular weight, average732 Purity, 99 + pct pure hydrocar Bon] "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility. The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction Co., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1947

By E. R. Stover, J. Wulff

A tentative 870°C isothermal section, the solidus equilibria, and the solubility of Tic and graphite in the nickel solid solution have been determined with arc-cast specimens. Each of the Ni-Ti intermetallics forms two-phase fields with Tic; only Ti,Ni has a measurable solubility for carbon. A quasi-binary eutectic exists between Tic: and a titanium-rich nickel solid solution; ternary eutectics occur on either side, with TiNis or with graphite. Graphite is in equilibrium with a nickel solid solution containing a ratio of Ti/C which increases below the solidus. DURING the past decade, titanium-carbide cermets containing nickel or cobalt alloy binders have been widely studied for high-temperature and wear-resistant applications. Recent work has emphasized control of the carbide grain size and distribution2's and the thermal exparision match between the phases/ The present study was initiated to determine the phase compositions during the sintering or infiltration process, and during subsequent heating. Although the effects of additives and impurities in commercial compositions are important, it was necessary to consider first the pure ternary, Ni-Ti-C. Emphasis was placed on the nickel corner, since the nickel solid solution is the continuous phase in compositions having highest strength. Early metallographic work by Zarubin and Molkov- showed that solid solubility at either end of the section Ni-Tic is small. Edwards and Raine reported that nickel dissolves between 3 and 5 wt pct Tic at 1250° C, on the basis of microstructures of annealed, vacuum-melted powder mixtures. Although the solubility of nickel in Tic has not been measured, Tic formed by the menstruum process in liuid-iron solution contains as little as 0.06 wt pct Fe. BINARY SYSTEMS The most recent determinations of the three binary systems are summarized in Fig. 1. Titanium carbide (6) is predominant among the binary phases, and it melts above the boiling point of nickel. The Ni-C binary is based on separate liquid solubility' ) and solid solubilitylo measurements. The eutectic temperature, 1328OC, is taken from the solidus determination described below. However thermal analysis data by Morrogh and williams also show eutectic arrests in this vicinity in the absence of supercooling. The Ni-Ti binary is taken from the work of Poole

Jan 1, 1960

Although the 71 Minerals operation is now closed down and the operating data presented is almost five years old, it is well worth describing since it was the first heap leaching operation conducted on a primarily silver ore. Tombstone was discovered in 1877 by Ed Schieffelen; and it became one of the most famous mining towns in the West through the stories connected with Wyatt Earp, Doc Holliday, and the Clanton brothers. Like many silver deposits .in the western United States, the Tombstone ores were relatively shallow. Several million ounces of silver were recovered in the relatively few years the camp was active; but mining virtually ceased by the early 1900s and was only continued in a small way until the 19409, a history similar to that of Tuscarora. The 71 Minerals operation was started in May 1975 and continued until late 1978 within the city limits of Tombstone on waste dumps; one was the' Lucky Cuss, Schieffelen's discovery, which had accumulated from the old underground operations. This waste material was mostly less than 50 mm (2 in.) in size, although there was some larger lumps. The grade was about 34 g Ag and 0.5 g Au per mt (1.0 oz Ag and 0.015 oz Au per st). The Tombstone dumps contained approximately 1,000,000 tons. The dumps and patented claims were held by a single owner, Tombstone Development Company, thus sufficient leaching material could be acquired from one source rather than dealing with a number of individuals, as is usual in putting together leaching ventures in old mining camps. 71 Minerals Ltd. was formed and a lease of the properties obtained. A site was selected close to the major mine dumps not far from down- town Tombstone. Pads approximately 90 m (300 ft) wide and 180 m (600 ft) long with an 8-degree slope were prepared using compacted old mill tailings as a base sealant on the pads. Mining was done at a rate of about 2,000 tons per day with a dozer, two scrapers, a front-end loader, and 30 ton trucks. The ore was dumped by the scrapers as it came from the dumps with no screening or crushing in 460 mm (18 in. ) layers and trimmed with the loader. Based on bulk sampling and laboratory testing, the majority of thegold and silver values were recovered within 30 days of leaching.

Jan 1, 1981

By Lewis A. Delano, Harold Rabling

It has been generally recognized that, owing to the extreme friability of galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth re-treating today. Investigations of the work of the Hancock jig on the Bonne Terre ore have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average for all conditions and grades of ore will be between 0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increascd smelting charges due to a greater amount of slime galena will be counterbalanced by the lower operating cost, increased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various Bow sheets, and to calculate the economics of the problem with great accuracy. Concentration Problem The ore occurs as widely scattered deposits of galena disseminated through limestone; it has a specific gravity of 2.8 and the following composition: Pb, 4.00 per cent.; Fe, 3.00 per cent.; Zn, 0.32 per cent.; S, 3.10 per cent.; MnO2, 0.73 per cent.; SiO2, 4.20 per cent.; Al2O3, 3.20 per cent ; CaO, 28.60 per cent.; MgO, 16.85 per cent.; CO2, 36.00 per

Jan 1, 1922

US 4,141,854-Method of resolving water-in-oil emulsions from the organic solvent extraction of uranium from an aqueous ore leach solution The emulsion is treated at optimum temperature with a water-soluble acrylamide copolymer which contains 5-50% by weight of a lower alkyl substituted tertiary aminoethyl methacrylate or quaternary ammonium salts thereof The emulsion is broken, enabling recovery and reuse of the organic portion of the emulsion A M Pavilcius and M A Latko, assigned to Nalco Chemical Co Feb. 27, 1979 3 pp (252-301 1W) Filed: 12-14-77 (860,542). US 4,142,952-In the recovery of copper from an ore leach solution, the solution is contacted with a water-immiscible organic solvent containing 5 to 20 g/L of o-hydroxyaryloxime and 2 to 20 times the weight of the o-hydroxyaryloxime of nonylphenol The loaded solvent phase is separated from the aqueous phase and stripped with sulfuric acid Copper is recovered rapidly and in high yield from aqueous solutions containing high copper concentrations R F Dalton, as¬signed to Imperial Chemical Industries Ltd Mar 6, 1979 6 pp (204-106) Filed 1-3-77 (756,067). Priority: United King¬dom, 1-30-76 (3788/76), 6-15-76 (24722/76), and 10-21-76 (43711/76). Same- British 1,549,615, dated Aug. 1, 1979 US 4,148,631-In the recovery of nickel and cobalt from a mixed sulfate ore leach solution, both metals are extracted by means of a cationic extractant, the loaded extractant treated with an aqueous chloride or thiocyanate solution to back extract the cobalt, and the cobalt then recovered by solvent extraction or ion exchange with an anionic extractant Recovery is effected in a relatively few extraction steps. F Babjak, V A Ettel, and K. R Dymock, assigned to Interna¬tional Nickel Co , Inc, Apr. 10, 1979 6 pp (75-101 BE) Filed¬7-27-78 (928,401). Priority- Canada, 12-28-77 (293,967) US 4,148,813-An improved extractant for use in the recov¬ery of nickel and cobalt from an ore leach solution comprises a water immiscible organic solvent system containing solubilized mercaptide ions, e g , dodecanethiol. Cobalt and nickel mercaptides solvated in the organic phase are easily stripped in the presence of carbon monoxide and an aqueous alkaline solution A. S. Rappas and J. P. Pemsler, assigned to Ken¬necott Copp

Jan 1, 1980

By T. R. Ingraham

The thermal decomposition of Nickel (II) sulfate was examined by determining the total pressure of SO3, SO2, and O2 developed over a sample when it was heated in an evacuated system fitted with a Pyrex-bellows mercury manometer. The equilibrium pressures were combined with previously published data on the oxide and sulfide systems to establish a predominance volume diagranz for the Ni-S-O system over the normal range of roasting temperature and gas composition used in the treatment of nickel minerals. The protective coating of NiSO4 which forms on the oxide during roasting, and which causes the sulfation reaction to almost cease, may be disengaged readily by temperature cycling. When nickel sulfide is roasted in air, either nickel sulfate or nickel oxide may be formed by altering the experimental conditions. Because of the differing stabilities of various metal sulfates and oxides, possibilities exist for separating some of the constituents of mineral mixtures by the technique of selective sulfation and oxidation roasting. The experimental information required to make reasonable predictions of the possibilities of this technique is incomplete and, in some cases, in conflict. As part of a general program of providing some of the required information, a study EXPERIMENTAL Materials, Apparatus, and Procedure. Fisher certified reagent-grade nickel sulfate hexahydrate was used in the source material for both nickel sulfate and nickel oxide. The manufacturer's analysis indicated: 0.001 pct Fe, 0.005 pct Cu, 0.003 pct Co, 0.001 pct C1, other 0.15 pct. The material was dehydrated, before use, by heating at 420°C for 5 hr. The oxide was prepared by roasting the sulfate in an open tray in a muffle furnace for 10 hr at950°C. Preliminary experiments which were made by thermogravimetric analysis and X-ray diffraction analysis established that only one crystal form of nickel oxide and one of nickel sulfate were involved in the equilibrium shown in Eq. [I]. The apparatus used in the experiments was described previously.1,3 The main feature is a corrosion-resistant, flexible Pyrex bellows which is used to protect the mercury in a u-tube manometer. Before a run was begun, the apparatus was washed thoroughly with hot hydrochloric acid and water and dried by heating under vacuum. The mixed sulfate -oxide sample was contained in a platinum bat rest-

Jan 1, 1967

By Douglas Bunting

The first presentation of this paper was before the Pennsylvania Anthracite Section of the Institute in May, 1914, after which a committee was selected to verify and add to the data contained in the original paper. The author is indebted to G. W. Engel, H. W. Montz, R. V. Norris, and H. H. Otto, of this committee, for additional information. I also wish to acknowledge the courtesies extended me by a number of the mining companies for information relative to accidents, systems of proving, and mining practice. The paper should bring forth additional criticism and recommendations, which will be of value in establishing future practice relative to this subject. Throughout the northern anthracite field of Pennsylvania glacial and alluvial deposits of sand, gravel, and clay exist in varying quantities. The extent and character of these deposits are described by N. H. Darton in Bulletin 45 of the U. S. Bureau of Mines, entitled, Sand Available for Filling Mine Workings in the Northern Anthracite Basin. It is estimated that the northern field contains 10,000,000,000 tons of these deposits, or a sufficient quantity to cover the 176 square miles of coal area to a depth of about 25 ft. These deposits of sand, etc., overlying the coal measures attain a maximum depth of more than 300 ft., and are usually saturated to such an extent as to render them semi-fluid. It is this condition of fluidity that limits the mining of coal seams cropping in or in close proximity to these deposits, and it is in the interest of safer and more efficient mining methods under these conditions that the study of this subject is here presented. The dangers incident to mining under deep deposits of sand have long been realized by operators in the northern anthracite field, and much has been done to prove the contour of the rock and vein croppings underlying these water-bearing deposits of sand and gravel. Although, as far as we know, the accidents of the past have not resulted in the loss of life, except in two instances, yet nearly all were attended with more or less miraculous escapes of men working in the vicinity of the breaks, so that the probable existence of pot holes, etc.,

Jan 1, 1915

By David Donoghue

THE. years 1901, 1910, and 1924 may be considered as the beginning of new eras in the history of the oil industry of the Gulf Coast of Texas and Louisiana. Spindletop, in 1901, with its enormous cap-rock production revealed the possibilities of the salt domes. The lateral sand development at Vinton, in 1910, renewed interest in the then known domes which were non-producing, or were producing from the cap rock or from sands above the cap rock. The discovery of three domes, Nash, Orchard and Long Point, in the year 1924, by means of the torsion balance and the seismograph, is the beginning of intensive explorations of the Gulf coastal plain by geophysical methods. Domes other than those mentioned have no doubt been found during the last few months of the year but tests have not been drilled to confirm the evidence of the instruments. DISCOVERY OF DOMES BY GEOPHYSICAL METHODS The Rycade Oil Corpn. operated the first torsion balance on the Gulf Coast in October, 1922, and the Roxana Petroleum Corpn. brought in one of these instruments and began work in December, 1922. The U. S. Coast and Geodetic Survey made some gravity observations at Damon Mound, in 1923, with a pendulum apparatus. In March, 1924, the Marland Oil Co. placed the first seismograph on the Gulf Coast and the Gulf Production Co. followed with one in May. In June, 1924, the Gulf Production Co. began operations with a torsion balance. The Atlantic Oil Producing Co., The Texas Co., and others have experimented with several types of instruments involving various principles. During the next few years, a great advance in geophysical methods may be expected, especially if one of the newly discovered domes should be productive. The first dome discovered was the Nash, in Fort Bend County, Tex., about 6 mi. east of Damon Mound. A slight elevation and two shallow wells containing sulfurous waters made the locality somewhat interesting from the standpoint of surface indications, and the torsion-balance measurements indicated the presence of a dome. On July 20, 1924, the Rycade Oil Corpn. No. 1 Wisdom encountered lime at a depth of 634 ft. and anhydrite at 639 ft. The hole was abandoned on Sept. 8, 1924, at 769 ft. in anhydrite. A cavity in the anhydrite caused much delay and the final abandonment of this test.

Jan 3, 1925

By James B. Austin

Growth of the Society When the Institute was born in May, 1871, it was given the name American Institute of Mining Engineers. Yet from its conception a few months earlier, its genetic code clearly carried the message that metallurgy was equal in importance to mining. Thus, the "call" for the initial meeting, which was sent out in April of that year by three mining engineers, Eckley B. Coxe, R. P. Rothwell and Martin Coryell, gave this first objective of the proposed organization as: "the more economic production of the useful minerals and metals." And this call concluded: "Anyone who may have devoted himself to a particular subject connected with either mining or metallurgy, and who may be possessed of new facts in reference to it, would greatly aid in furthering the objects of the proposed association by preparing a paper giving the results of his experience." In response to this call, a group of 22 men assembled in Wilkes-Barre, Pa., for a 3-day meeting beginning May 16, 1871. On the first day, a set of 20 "Rules" was adopted, of which Number 8 read, in part: "The words mining engineers in these rules comprehend engineers connected with mining and metallurgy." On the second day, 18 officers were elected, of whom nine were not present. Moreover, as if to emphasize that the words about metallurgists were to be taken seriously, one of those elected in absentia was the president, David Thomas, a Welshman who had founded the Thomas Iron Co. and who built the first anthracite-fired, hot-blast furnace in this country. The second meeting of the Institute, held in Bethlehem, Pa., in August, had a more metallurgical flavor, and the third meeting, in November, was held in what was then one of the great steel-making centers of the country - Troy, N. Y. This was the home of the Albany and Rensselaer Iron and Steel Co., which held the American rights to Bessemer7s machinery patents. And it was here that the great American steel master, Alexander L. Holley, carried out a series of experiments that led to improvements in the design and method of operation of the Bessemer vessels. It was at this meeting that Holley and Henry Marion Howe, then a "student" at the Albany and Rensselaer plant, were admitted to membership. Four years later, Holley was elected president of the Institute. Clearly, metallurgy

Jan 1, 1971

By Gordon G. Bentle, W. P. Fishel

GREINER, Marsh, and Stoughton1 have reviewed the literature in a monograph on the iron-silicon system. The lack of agreement among the various studies may be due to the difference in the purity of materials in some cases. The results of the X-ray method indicate only a general rather than a specific limit of the y loop. The iron-titanium system was investigated by Roe and Fishel,' whose results are used in determining the iron-silicon-titanium y loop. The literature indicates that no study has been made thus far of the iron-silicon-titanium system in the y loop region. Experimental Procedure The alloys were made from Armco iron, 99.86 pct Si, and 98.5 pct Ti. The titanium contains 1.07 pct Fe. The Armco iron contains 0.01 pct C, 0.005 pct Si, 0.02 pct Mn, 0.006 pct P, 0.01 pct S, and 0.04 pct Cu. A dilatation sample of Armco iron was prepared in the same manner as were the other samples. Several dilatation runs indicated that Ac3 begins at 905°C and ends at 910°C, which compares favorably with the study of Wells, Ackley, and Mehl' employing specially purified iron. All alloys were melted in an induction furnace in Alundum crucibles and were top poured into baked core sand molds. The ingots weighed about 600 g as cast. Dilatation samples of 4 in. by % in. diam were taken from the bottom end of the ingot, from which turnings for analysis were taken. Turnings from each end of two of the samples indicated that the alloys possessed uniform silicon content. A hole was drilled halfway through each end of a 4 in, dilatation sample. A chromel-alumel thermocouple was inserted in each hole and the surrounding metal peened in to hold the thermocouple in place. Fig. 1 represents the dilatation apparatus. The heating unit is an Alundum tube wound with resistance wire; the dilatation tube is a McDanel combustion tube; the push rod is zircon; the dial gage is graduated in 0.0001 in. and was vibrated to prevent sticking. A blank run over the temperature range of interest gave no significant dilatation. The thermocouples were attached to a multiple recording micromax which indicated the temperature at each end of the sample at 35 sec intervals. A Lindberg control unit governed the rate of heating of the furnace, and lowering or raising the

Jan 1, 1957

By W. R. Opie

The object of this paper is to show the manner in which typical electrodeposits of hexagonal-close-packed metals—zinc, titanium, and zirconium—tend to form. The conditions of electrodeposi-tion markedly affect the nature of the deposits in regard to crystal size, orientation, and appearance. No attempt is made to correlate cell conditions with deposit quality but, rather, characteristic types of deposits were selected and a study made to show the relationship between outward appearance and crystal structure. The zinc deposits were made in aqueous electrolytes and the titanium and zirconium deposited from fused salt baths. ZINC deposits studied were made in the American Smelting and Refining Co.'s Central Research Laboratories. They were representative of bright, shiny, smooth deposits, which can be obtained by using proper current densities and electrolyte addition agents, and of deposits which are dull and tend to be nodular. Four deposits were selected which ranged from smooth and bright to very nodular and dull, and their classifications are shown in Table I. These were examined microscopically and were found to differ quite markedly in outward surface structure and in microstructure. The outward surface variation is illustrated in Figs. 1 to 4. At X50 the texture could be seen to progress from granular to platelike to smooth. The microstructures of the deposits' cross sections from starting sheet to outer surface are shown in Figs. 5 through 8. The dull nodular deposits (sample Nos. 1 and 2) show some tendency for acicular growth. The platelike sample (No. 3) shows tendency for columnar growth development and the smooth deposit (No. 4) has a well developed columnar structure. Back-reflection X-ray patterns of the deposit surfaces revealed some interesting information. The crystal orientation was random in all deposits except the smooth deposit. Fig. 9 is a typical back-reflection pattern of a nodular deposit. All planes are reflecting in the proper relative intensity. The pattern of the smooth deposit is shown in Fig. 10. The only planes which reflect are the (10.4). This series of planes is in the right position, with the FeKa radiation used, to satisfy the Bragg equation if the basal planes {00.1) are at right angles to the X-ray beam. The results were interpreted to mean that in the bright smooth deposit preferred orientation has occurred with the basal hexagonal planes oriented in the plane of the sheet but with all other planes randomly oriented around the c-axis.

Jan 1, 1957

By George H. Ashley

The Legislature of the Commonwealth of Pennsylvania at its last session passed a new act dealing with barrier pillars, which may have a wide interest in other states. In the past the laws of Pennsylvania have required that the superintendent of a mine "shall not permit the mining of coal within 50 ft. of any abandoned mine containing a dangerous accumulation of water, until said danger has been removed by driving a passageway to tap and drain off said water, as provided for in this act: Provided, That the thickness of the barrier pillars shall be greater aid shall be in proportion of one foot of pillar thickness to each one and one-quarter feet of water head, if in the judgment of the engineer of the property and that of the district inspector it is necessary for the safety of the persons working in the mine." Thus it has happened that a thickness of several hundred feet has necessarily been left in pillars in mining. It has seemed to many in the mining industry that this left an unnecessary amount of coal in pillars, and did not provide that the pillar be left equally on the two sides of the mine. As a result the General Assembly of 1927 by Joint Resolution authorized the Governor to appoint a Commission of "seven prominent citizens, of whom four shall be recognized mining engineers, one shall be a hydraulic engineer, one a geologist of recognized standing in his profession, and one a State mine inspector from the bituminous coal mining district, to investigate and report upon barrier pillars in the bituminous coal region." The Governor appointed the following Commission: Morris Coulter, Clearfield Bituminous Coal Corp., Indiana, Pa.; A. E. Roberts, Monroe Coal Mining Co., Revloc, Pa.; George T. Lewis, Westmoreland Coal Co., Irwin, Pa.; Morris Knowles, hydraulic engineer, Pittsburgh, Pa.; Thomas A. Mather, State Inspector of Mines, Tyrone, Pa.; A. B. Jessup, Anthracite Coal Operators Association, Jeddo, Pa.; George H. Ashley, State Geologist, Harrisburg, Pa. Mr. Coulter was elected Chairman and Mr. Ashley, Secretary. This Commission held meetings in Harrisburg, Johnstown and Pittsburgh. It obtained and considered the laws and experiences of other states and European countries. Some of its members conferred at length with the directors and other members of the U. S. Bureau

Jan 1, 1930