Search Documents

By J. W. Rutter, K. T. Aust

Competitive growth of recrystallized grains into striated single crystals of zone-refined lead produced preferred orientations of the coincidence type after annealing at 175°C, but not at 300°C. This preferred orientation development was found to result from the higher mobility and lower energy of large -angle coincidence boundaries compared to large-angle noncoincidence boundaries. These mobility and energy difference provide a useful basis for explaining many cases of preferred orientation observed in annealed metals. DURING a study1 of the mobility of grain boundaries in zone refined lead, it was observed that the temperature dependence of the grain boundary migration rate is smaller for large-angle, coincidence-type grain boundaries than for large-angle noncoincidence ("random") boundaries. This observation is illustrated schematically in Fig. 1, which shows log rate of grain boundary migration vs reciprocal absolute temperature for two large-angle boundaries. The upper curve refers to a coincidence-type boundary of the sort discussed by Kronberg and Wilson.2 While the mobilities of these two boundaries are similar at 300°C, the coincidence-type boundary has a greater mobility, by a factor of about: four, at 175°C than does the noncoincidence boundary illustrated in the lower curve. The observation described above suggested a simple experiment for testing the role of grain boundary mobility in the development of preferred orientation in annealed, high-purity lead. On the basis of this observation, it would be expected that if a large number of grains of different orientations are growing competitively, and if relative grain boundary mobility is a controlling factor, then the specimen procluced by boundary migration will contain crystals having random orientations if annealing is done at 300°C, while preferred orientations of

Jan 1, 1962

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By C. A. Winkler, V. Hospadaruk

PREVIOUS papers from this laboratory have discussed the effect of chloride ion on the cathode polarization during electrodeposition of copper from copper sulphate-sulphuric acid electrolytes, in the presence and absence of gelatin. The steady state polarization'" was found to decrease sharply and pass through a minimum with increasing chloride ion concentration in the presence of gelatin. The minimum shifted to higher chloride ion concentrations and to higher polarization values with increase in current density or gelatin concentration, while an increase of temperature shifted the minimum toward lower halide concentrations and lower polarizations. Since these observations were made in acid-copper sulphate electrolytes that contained no other addend than gelatin, there was obviously the possibility that they were not applicable to deposition of copper from commercial electrolytes that contain a variety of other substances in relatively small amounts. In particular, it was of interest to determine whether the presence of arsenic, antimony, or bismuth in the electrolyte would materially alter the behavior. Experiments have now been made under a variety of conditions with systems containing these cations, and the results are summarized in the present paper. Experimental Polarization measurements were made at 24.5oC in a Haring cell in the manner described previously.' Electrolytes were made with doubly-distilled water, and contained 125 g per liter of copper sulphate and 100 g per liter sulphuric acid, both of reagent grade Eimer and Amend gelatin from a single stock was used throughout. Chloride ion was introduced as reagent grade sodium chloride, and arsenic, antimony, and bismuth by dissolving the chemically pure metal in hot concentrated sulphuric acid and adding appropriate amounts of the solutions to the electrolyte. Each cathode, of 1/16-in. thick rolled copper, was first etched in 40 pct nitric acid and washed thoroughly with distilled water. The surface was then brought to a standard condition4~9 by electrodeposition from an acid-copper sulphate electrolyte containing no gelatin, at a current density of 3 amp per sq dm for 30 min, followed by deposition at a current density of 2 amp per sq dm for l hr. As in previous studies, the cathode polarization eventually attained a steady-state value (15 to 75 min) such that further change in polarization did not exceed 0.2 mv per min. The polarization values recorded are those for the steady states. "Excess weights" were determined with arsenic and antimony present in the electrolyte, as the difference between the weights of the deposits obtained in the presence of these cations and those obtained in their absence, with the two cells connected in series. When gelatin was present along with the arsenic or antimony, it was also added to the electrolyte in the cell in series. Results and Discussion The results of the study are summarized in Figs. 1 to 6. From Fig. 1, top, it is evident that the presence of arsenic or antimony alone results in an increase of polarization, while bismuth alone causes a decrease. The presence of gelatin (25 mg per liter) rather drastically modifies all three cation effects, as indicated in the lower panels of the same figure. The addition of chloride ion, when no gelatin is present, causes comparable decreases in polarization in the presence of antimony and bismuth, but a relatively larger decrease when the electrolyte contains arsenic. It is interesting to note that the decrease in polarization brought about by addition of chloride when both arsenic and antimony are present parallels the behavior with arsenic alone, while the polarization in the electrolyte containing the cation mixture, without chloride added, corresponds to that for an electrolyte containing only the antimony cation. Similarly, the polarization at zero concentration of chloride in electrolyte containing arsenic and bismuth is that corresponding to an electrolyte containing arsenic alone. From Figs. 3a, 4a and 4b, it is clear that, in the presence of gelatin at a level of 25 mg per liter, the effect of chloride in the presence of arsenic and antimony, or a mixture of the two, becomes quite analogous to that observed in the absence of added cations. When both bismuth and gelatin are present (Fig. 5), the decrease in polarization with increased chloride concentration is virtually absent. This is perhaps a reflection of the large decrease in polarization brought about by the bismuth itself in the presence of gelatin. The shifts of the minimum in the polarization-chloride concentration curves brought about by changes of temperature (Fig. 3b), gelatin concentration (Figs. 3c and 4c) and current density (Fig. 3d) when the metal cations were present are all similar to the corresponding shifts observed in their absence." The approximately linear "excess weightv-anti-mony concentration relation recorded in Fig. 6 would seem to indicate that antimony is codeposited with copper to a considerable extent. On the other hand, only very limited amounts of arsenic appear to be adsorbed or codeposited.

Jan 1, 1954

By R. M. Fowler, H. L. Hamner

DURING the last 25 years, there appeared in the literature a number of papers describing equipment and operating techniques for the determination of total oxygen in iron and steel. In the early papers, comparatively little attention was paid to side reactions that occur when iron is saturated with carbon at a high temperature in a high vacuum. As more experience was gained with the new method, the limitations appeared. Metals, with a boiling point lower than iron, distilled out of the crucible, condensed in the cooler part of the furnace, and subsequently reacted with carbon monoxide to form oxides and carbon. Aluminum, manganese, and the alkaline earth metals proved troublesome in this respect. Modifications have been devised to overcome the difficulties due to aluminum and manganese, while the alkaline earth metals are not of too much concern as yet to the steel chemist. The reactions of sulphur have received less attention, although it is generally recognized that some carbon disulphide is probably formed. Liquid air traps have been used in some cases to prevent any carbon disulphide from entering the analytical train. Sulphur was not a particular problem at the Union Carbide and Carbon Research Laboratories until the analysis of the irons of higher than usual sulphur contents became necessary. In order to describe the procedure developed for such irons, it will be necessary to first describe the type of vacuum-fusion equipment employed because the operation of vacuum-fusion equipment is an art to a considerable extent. At the Laboratories, vacuum-fusion equipment has been in daily operation since about 1930. Over the years, the evolution of this apparatus has been governed by the versatility required to analyze a wide variety of materials. Since all types of materials from high purity metals to slags are analyzed and, since seldom more than a few samples of one type are analyzed in succession, the apparatus was designed for accuracy and flexibility rather than for speed. A general view of the equipment is shown in Fig. 1, while Fig. 2 shows the relationship of the various parts. In Fig. 2, A is a vertical double-glazed 24X27/8 in. OD silica tube heated with a 20 kva mercury-arc high frequency generator. The tube is closed with a water-cooled brass head attached with de Khotinsky cement. A turret cap fits on this head and is sealed with a 1/8x3 in. "0" ring. The head contains a sight glass and two 8 in. horizontal glass tubes, for sample storage, cemented in with de Khotinsky cement. B is a four-stage Gaede mercury diffusion pump connected to the water-cooled head with a 11/2 in. copper tube through a flange with an "0" ring. The output of the vacuum pump feeds into an automatic Toepler F pump which compresses the gas sample over mercury in the measuring burettes, G and H. There are bypasses in this line for a McLeod gage C and a Piranni gage D, a manometer E, and for initial pumping out of the system with a Cenco Megavac backing-up pump. The reduction crucible shown in Fig. 3 is machined of Tungar Bulb quality (A.G.K.T.E.-2) graphite. The sample is guided into the crucible with the graphite funnel depicted on this figure. The arrangement of the crucible, radiation screens, etc. in the furnace is as follows: A 1 15/16x61/2 in. Alundum thimble, porosity RA-84, with two 1/8 in. holes near the top and opposite each other which take a pair of special tongs used for lowering it in place, is prepared. A 3/4 in. layer of powdered graphite is placed in this Alundum thimble, and the graphite crucible containing 20 g of ingot iron and 0.5 g of carbon is carefully centered on this bed of graphite powder and graphite powder is packed around it to the top of the graphite cru-

Jan 1, 1953

By F. L. Toy, C. E. Sims

PNEUMATIC processes for converting molten pig iron to steel were the major producers of steel during the latter half of the 19th Century and until shortly after the turn of the century, when these processes began losing ground to their rival—the basic open hearth process. The first pneumatic process for converting molten pig iron to steel was introduced almost simultaneously by Sir Henry Bessemer in England and by William Kelley in the United States during the decade 1850-1860, but it was Bessemer who pushed it to a successful commercial operation. The process itself is so basically simple that it has not lent itself to many extensive or revolutionary improvements since its inception. During the first 30 yr, numerous' designs of vessel and many modifications of practice were tried before the industry standardized on something resembling current practice. The evolution in construction has resulted in proportions and arrangements based more on mechanical expedience than on metallurgical requirements. Many of the early converters were stationary and had to be tapped similarly to the cupola or open hearth furnace. Such types were used for many years in Sweden and Germany, but the rotating or tilting types were favored in England and the United States. There was evident trouble with bottom tuyeres, becAuse about half of the early designs were constructed for side blowing with tuyeres submerged below the metal-bath surface. Even portable tuyeres, introduced from above, were tried. The principal advance, which made bottom blowing practical, was the invention, in 1863, by Henry Bessemer, and subsequent improvement by A. L. Holley, of a detachable bottom so that the tuyere section could be renewed. In the meantime, it was the demonstration, by Robert Mushet, of the value of manganese in overcoming hot-shortness in converter steel, that made the process metallurgically feasible. At first, only the acid practice was used, and Swedish pig iron, because of its low sulphur and phosphorus, was in great demand. The development of a suitable basic lining, by Sidney G. Thomas and Percy G. Gilchrist in 1876-1879, made the process applicable to the high-phosphorus ores of Europe. From the beginning of the use of the Thomas-Gilchrist process, trouble was experienced in obtaining sufficiently high temperatures in the blown metal, particularly in small heats. It is necessary, of course, to have the low-carbon blown metal at a considerably higher temperature for handling from vessel to ladle to molds than is needed for the molten pig iron. All of the increase in temperature in a pneumatic process must be obtained from the heat of combustion of the elements contained in the pig iron plus that from silicon when ferrosilicon is added. In bottom blowing practice, carbon is almost completely burned, but inasmuch as it cannot be oxidized to a higher state of oxidation than to CO when in contact with liquid iron, only a minor portion of the heat-producing capacity is utilized. Under such conditions, it is not considered to be an efficient source of heat. In the acid practice, therefore, silicon and manganese are the large heat producers, are quickly oxidized, and are efficient fuels. Too much manganese, however, thins the slag greatly and tends to promote excessive slopping or throwing of slag and metal from the converter during the blow. Most operators, therefore, like to keep the manganese content of the iron below 0.60 pct, and thus the main source of heat is the silicon, which must be at least 1 pct and sometimes 2 to 3 pct for small blows such as for castings. Ferrosilicon is sometimes added during the blow to obtain an adequate temperature level. In the basic (Thomas) practice, even more heat is required, because cold lime is added to flux the phosphorus after it is oxidized, and the basic slag must be maintained at a proper temperature. Silicon

Jan 1, 1951

By Noel Jarrett, Allen S. Russell, Bernard M. Starner, Stanley C. Jacobs

A process has been developed to refine high-grade commercial aluminum to 99.99 pct purity. This enzploys precipitating titanium, vanadium, and zirconiu~ as borides. The upgraded liquid is partially crystallized under conditions that prevent massive freezing. The resulting crystals are compacted and washed free of adhernig impure liquid aluminum by melting the top crystals while draining off the liquid. Finally, the bottorn portion of the crystal bed is melted and removed as the pure product. Leakage from the crystallizat~on vessel is prevented by a layer of alumina granules that are not wetted by the aluminum. ALUMINUM of 99.99 pct purity is desired in a variety of applications. These include electrolytic capacitors, catalyst carriers, decorative trim for automobiles, aluminum powder, and high-strength alloys. This market was for many years filled by refining commercial-purity aluminum in a three-liquid-layer electrolytic cell of the type originally proposed by Hoopes. To meet the expanding need for lower-cost high-purity aluminum, a refining process based on chemical precipitation and fractional crystallization was developed. The availability of this super-purity metal was announced in November 1961, and three patents1-3 relating to the process were issued in 1965. An alternate process, comprising continuous fractional crystallization of a portion of a liquid-aluminum feed stream under conditions of strong agitation at the surface of the growing crystals, was published by Dewey4 in 1965. Earlier proposals by Larsen 5 and by Regner6 also emphasized the advantage of rapid agitation of the melt in the region of the crystallization zone. johnson 7 more recently proposed extracting purified aluminum from an alloy by mixing crystals of pure aluminum into the molten alloy, allowing them to grow, and removing the pure aluminum as by casting. Aamot's 8 recent patent describes a freeze refining process that involves controlled partial freezing against cooled moving retort walls. The Alcoa process to produce high-purity aluminum is schematically described in Fig. 1. Relatively pure aluminum is treated with boron in a furnace (a) to precipitate high melting point impurities, the supernatant liquid is transferred to a crystallization vessel (b), the liquid is partially crystallized with mechanized "tamping" (c), the remaining impure liquid is tapped out and the crystal bed partially and directionally re-melted to wash the underlying crystals (d), and the balance of the crystals is melted and withdrawn as high-purity aluminum (e). PRINCIPLES OF FRACTIONAL CRYSTALLIZATION Commonly encountered impurity elements form two types of systems with aluminum. Titanium, vanadium, and some other transition elements in periodic groups IV, V, and VI are the high melting point impurities. Initial solidification of aluminum containing small percentages of these elements will produce solid markedly enriched in them at temperatures slightly above the freezing point of high-purity aluminum. Most other elements, such as silicon and iron, produce eutectic type reactions with aluminum. In this case the first solid formed on initial solidification at temperatures slightly below the freezing point for high-purity aluminum is markedly depleted while the remaining liquid is enriched in these elements. The equilibrium change in composition during solidification of aluminum contaminated with silicon, iron, or titanium is illustrated in Fig. 2. Here, for clarity, the temperature scale is expanded beyond the

Jan 1, 1968

By George Fancher, R. L. Whitting

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By R. L. Whitting, George Fancher

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By R. B. Sosman, J. C. Hostetter

We have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. Magnetic FRactionation of Oxides of Iron The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can bc adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several fractions of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 1, 1918

By James Douglas

At this last meeting of our Institute for the year 1899, it is appropriate that we should look back at the past. To review the century's progress in the exact sciences and the resulting arts that fall within the scope of our labors is beyond my ability. But I wish to draw your attention to some phases of that progress, almost as important, which lie within the zone of sociology, touching at so many points the domain of applied technology. One of these is suggested by the library of technical literature which this century has produced —not the least important contribution to which is our own Transactions. The nineteenth century has witnessed the beneficial spread of democracy in politics. Under the impulse, to no small degree, of the same spirit, there has grown up a brotherhood of fellow-workers and a sense of fellow-ownership in the secrets of nature. Though the Patent Office has assumed such proportions as to hare become a source of national revenue, and a multitude of inventors, great and small, are seeking through its agency to secure some pecuniary profit from their devices, there is even greater eagerness among both interested and disinterested workers in the field of technology to publish their observations, and even their discoveries, and to give them to the world without remuneration. The motives influencing the great body of writers who, without any pay, use the technical journals and such media of communication as our Transactions, in order to give to the brethren of their craft the results of

Jan 1, 1900

By d&apos, K. Mukherjee, C. R. Antonio, R. J. Maciag, G. J. Fischer

Tensile data indicate that over the range of strain rates 10-5 to 10-1 sec-1 and in the temperature range 298° to 743°K the flow stress at a given temperature may be expressed as: C0 = Cem where m changes abruptly at a critical strain rate of 10-2 sec-1. The Zener-Hollomon parameter was tested and found to be invalid except at temperatures exceeding 700° K. Values of AH calculated for temperatures above 700°K ranged from 30 to 47.5 kcal per g-mole. ThE flow characteristics of aluminum and aluminum alloys as a function of temperature and strain rate have been of interest to various experimenters for many years. Trozera et al.1 determined tensile flow curves for pure aluminum and concluded that the combined effect of temperature and strain rate on the flow stress could be related using the Zener-Hollomon parameter. More recently, Hockett2 proposed a relationship between compressive flow stress, temperature, and true strain rate which could be represented by a surface. Holt et al.3 studied strain rate effects on flow stress in a number of aluminum alloys at room temperature. It was determined that there is a critical strain rate above which a strain rate effect is observed. It was also reported that the strain rate sensitivity was significant in aluminum alloys in the "0" condition only. In a recent review paper McQueen4 has considered a number of mathematical expressions which have been used to describe the relationship between stress, strain rate, and temperature. These expressions have been applied to the flow characteristics of a number of different metals and alloys including aluminum. In the present work the strain rate sensitivity of 7075-0 aluminum was determined in the temperature range of 298° to 743°K. The tensile flow stress at 0.2 pct offset was obtained over a nominal strain rate range of 10-5 to 10-1 sec-1. EXPERIMENTAL Threaded tensile specimens were cut from a single heat of 7075-T6 aluminum. The composition of this heat is given in Table I. The test bars had a gage section 1.5 in. long by 0.250 in. diam and conformed to ASTM specification E-8-57T. After machining, the bars were annealed at 413° ± 10°C for 2 hr. They were then cooled to 260°C in 3 hr, and finally air cooled to room temperature. This treatment is commonly used to produce the "0" condition. Load-time curves at constant crosshead speeds were obtained at various temperatures using an Instron testing machine. Crosshead speeds ranged from 0.002 to 40 in. per min. A three-zone resistance tube furnace was used for the elevated-temperature tests. Temperatures were measured at three points along the gage length by means of suitably placed thermocouples. Each tensile bar was held at temperature for 30 min prior to testing and the maximum temperature variation along the gage length was kept below 1°C. In all, 275 samples were tested and each data point plotted is an average of at least two tests. In many cases the point represents up to six tests. RESULTS AND DISCUSSION Values of the flow stress at 0.2 pct offset at six different temperatures are plotted vs strain rate on log-log coordinates in Fig. 1. Over discrete ranges of strain rate, the data for each temperature fit the expression:

Jan 1, 1969

By D. F. Toner

THE decomposition of the ß phase in the copper-aluminum system has recently been subjected to considerable investigation1-4 As a result of this work, principally by Haynes, much additional interest has been aroused concerning the various transitional or metastable phases in the Cu-A1 system. No attempt has been made to resolve the question of whether the PI and ß" phases of Klier and Grymko5 are the same as the rosette-shaped phase first observed by Smith and Lindlief6 in 1933 during an isothermal transformation study of an eutectoid alloy. It is the purpose of this study, however, to obtain

Jan 1, 1960

By A. P. Young, L. I. Marsh

HE relationship between microstructure and *- fracture is of interest in many metals and alloys. This relationship is sometimes established by examining the fracture surfaces and the flat surfaces near the fracture path in tensile samples. However, it is often difficult to tell from examining the fractured sample whether the fracture is intergranular, intra-granular, or a mixture of both. Also, it is often of interest to follow the progress of slip, twinning, or crack formation along the fracture path before fracture occurs. The ambiguity concerning the type of fracture generally can be resolved if the area along the path of ultimate fracture can be photographed at inter-

Jan 1, 1959

By R. S. Barneyback

Not much more is known about concrete today than was known to the Romans. For all the research only better tools have resulted to measure the quality of the materials that go into it." In this paper "some of the materials for lightweight concrete and their characteristics are considered and effort is made to indicate their effect on the end result — a structure of lightweight concrete." Lightweight concrete had noble beginnings. It is believed that the first specification for lightweight concrete was written by the Roman Emperor Hadrian in the early years of his reign, 117-138 AD. Hadrian, was an engineer by trade and an Emperor by adoption. He took considerable interest in the structures sponsored during his reign, even to the point of working out the structural details and preparing working drawings for some of the more prominent works in the vicinity of Rome. In order to reduce the dead weight of the 140 ft diam dome of the Pantheon he specified that the lightweight structural concrete members supporting this concrete and tile composite dome were to be fabricated from a concrete containing pumice and scoria. Still standing after 18 centuries of abuse, this structure has been described as the master effort of a great structural genius, the ultimate achievement of Roman engineering skill.' The Romans were the first to employ many concrete techniques we think of as modem innovations. Some unnamed superintendent noted that when a carefully measured amount of pigs blood was measured into each batch of concrete during mixing, the concrete was more durable and exhibited much better resistance to freezing and thawing climates. He no doubt, attributed this success to the appeasement of one of the gods who in return provided protection for the building containing this sacrificial offering in its walls. It is known today that the blood-entrained air in the concrete tends to make mixtures more workable, resistant to moisture penetration and more resistant to frost damage.

Jan 1, 1964

By J. F. Butler

The degree and type of carbide dispersion resulting from changes in the cooling rate from austenite determine the amount of carbon remaining in solution after slow cooling- from a subsequent subcritical annealing treatment. A difjusion model has been proposecl to explain the effect of carbide dispersion on the amount of carbon retained in solution and the amount of carbon in solution has been related to the degree of carbon strain aging. COTTRELL and Leak' have shown that the rate of strain aging in low-carbon steels is dependent upon the amount of carbon and nitrogen in solution. Carbon can be effectively removed from solution as Fe , C by quench aging at temperatures of 200" C or lower; however, the relatively higher solubility of nitrogen at these temperatures prevents sufficient removal of nitrogen as iron nitrides. For this reason, nitrogen in solution has been considered the major cause of strain aging in rimming grades of commercial low-carbon steels. Nitrogen can be effectively removed from solution and nonaging steel produced through the addition of aluminum to form the stable nitride, AlN; however, the aluminum also causes deoxidation resulting in a killed steel. III an attempt to produce a rimmed steel which was also nonaging, Morgan and Shyne 2 investigated tile strain-aging properties of low-carban steels containing boron and found that strain aging was suplx-essed in steels containing as little as 0.007 pet B. The original purpose of this investigation was to determine the mechanism of strain-aging suppression by boron. Early in the study, the function of boron was discovered to be much like that of aluminum in that the formation of a nitride, BN, removed the nitrogen from solution.' However, during the course of the investigation, an effect of heat treatment upon the strain-aging properties and the amount of carbon in solution was found which could be related to the microstructure of the steel. The purpose of this paper is to examine these relationships among heat treatment, microstructure, carbon in solution, and strain aging in steels where nondetectable amounts of nitrogen are present in solution. EXPERIMENTAL PROCEDURE The investigation was carried out using 0.030 in. by 12. in wire specimens which had been cold swaged and drawn to the final diameter. Table I lists the compositions of the low-carbon steels used. Those with 'V' designations were vacuum melted and cast; the alloys designated 'AISI' were prepared from high-purity iron obtained from the American

Jan 1, 1962

By Edwin R. Walker

The old adage, " Necessity is the mother of invention," is fully borne out in the case of the device described in this paper. About four years ago the firm of the writer received instructions from Sir John Hawkshaw, C. E., and I. Wolf Barry, Esq., C. E., to construct and erect three large Guibal fans for ventilating a portion of the Metropolitan and District Underground Railway, of London. On account of the cost of coal and the very limited space for boilers, it was arranged that the fans should be driven by gas-engines. Those who have had experience with Guibal fans will be aware that as each blade or vane passes the lower edge of the shutter a pulsatory action takes place. When the fans above mentioned were set to work, the pulsation or vibration of the immense volumes of air discharged was so great that it caused a corresponding vibration of the window-sashes, doors, etc., of the surrounding buildings; and this was so unpleasant that the shopkeepers and others near obtained an injunction against the railroad company, compelling it to stop one of the fans. The work was by this time out of our hands, and we only casually heard what had taken place, learning also that, in addition to this injunction, another was threatened in the case of the second fan, and that the railroad company had thus far escaped the enforcement of this threat by agreeing to run the second fan at a few short stated intervals only during each day. In considering the case, it occurred to us to incline the lower edge of the shutter, instead of making it parallel with the axis of the fan,. by which means we thought that the waves of air might be broken

Jan 1, 1891

By Eckley B. Coxe

Having been appointed, on February 19th, 1890, a member of the Commission created by the Legislature of Pennsylvania for the purpose of investigating the " Waste of Coal Mining, with the View to the Utilizing of the Waste" (waste in this case referring specially to the small sizes of anthracite heretofore thrown away), my attention was naturally directed to the mash economical method of burning these small sizes.* Although I had been Familiar with the burning of anthracite for • many years, I found when I came to study the matter carefully that I was far from thoroughly understanding it, particularly with reference to the hurning of the smaller sizes, and that the literature of the subject, which was not very extensive, had more of a tendency to confuse than to enlighten me. I began therefore to investigate the subject so as to arrive if possible at some definite principles applicable to the question. With the aid of my assistant, Mr. John R. Wagner, I began at Drifton a series of experiments upon the burning of small anthracites. We first erected a small furnace with a grate 3 feet long and 2 feet wide, with which we experimented about two months. From the information thus acquired, we designed and built another furnace of about the same size, which gave us facilities for extending our investigations still further. After experimenting several months with the second furnace, we built a third one, which was much larger, having a grate area of about 68 square feet, which was exactly the size of the grate used in the boiler-plants of' Coxe Bros. &

Jan 1, 1894

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995 pct A1 under conditions of elastic strain and plastic creep straining was investigated using a fractional recovery parameter. Tensile straining was conducted at room temperature to a true strain of 0.10, and recovery treatments were made under stress in the temperature range from 80° to 198°C. Whereas elastic strains had no appreciable influence on flow-stress recovery, plastic creep straining was found to accelerate the recovery process. Although higher creep stresses gave greater recovery for a given time and temperature, it was found that lower stresses produced greater recovevy at equal ALTHOUGH many studies have been made to date on the recovery of metals from the cold-worked creep strains above about 0.005. This effect was attributed to the coarser, and therefore weaker, substructure developed during creep at the lower stresses. The activation energy for recovery during creep straining at 2075 psi between 160" and 198°C was found to be 25,000 cal per mole. This value was not significantly greater than the value previously obtained for no-load recovery. The activation energy for creep at 2075 psi between 160" and 198°C was 34,000 cal per mole, a value significantly greater than that for recovery under the same conditions. state, little is known concerning some important aspects of recovery behavior. One such area is the effect concurrent strain has on the recovery process. Since metals in structural applications at high temperatures are under stress, the possible effects of the resulting elastic and plastic strain on recovery may be of significant importance.

Jan 1, 1962

By J. S. Kirkaldy, R. J. Brigham

AS part of a program to investigate the diffusive properties of dilute ternary austenites we have made a determination of the effect of chromium on the activity of carbon in ? iron. Samples of pure iron and Fe-Cr alloys were simultaneously equilibrated at 1000°C with atmospheres of controlled CO/CO2 ratio following the procedures of Darken and Gurry 1 and smith.' The 0.020 in. thick samples were analysed for carbon by microcombustion analyses3 to yield a set of isoacti-vity curves. The latter were converted to activity coefficient (standard state at infinite dilution) plots by combination with Smith's data2 for the activity of carbon in pure iron. Table I shows the compositions of the base alloys used while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In?C=6.9NC- 10.7 Ne In the notation of wagner4 the interaction parameter is the second coefficient on the right, Sgr = - 10.7 This can be compared with a rather inaccurate value deduced from the transient equilibrium diffusion data of Kirkaldy et al.' as The authors are indebted to the American Iron and Steel Institute for financial support. This material is condensed from a B.Sc. Thesis submitted to Mc-Master University by R.J.B.

Jan 1, 1963