Search Documents

By F. W. Clark

At the present time, when lixiviation versus amalgamation is being so thoroughly discussed by practical men, and published information is so meagre, the following tests, made by students in the mining laboratory of the Massachusetts Institute of Technology, may be of interest to others. The ore experimented upon was obtained from the Sombrerete mines near Zacatecas, Mexico. A careful analysis of the dried sample resulted as follows : Per cent. SiO2,............62.79 S.............13.86 Al2O3............4.39 Fe,............11.26 Zn,............1.57 CaO.............2.91 MgO,........... 0.06 Cu,.............0.12 Pb,.............0.40 Sb and As,..........trace CO2,............2.35 Ag,.............0.16 99.87

Jan 1, 1886

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed 'that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed 'that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Howard N. Evanenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. AVERAGE RECOVERY The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered-it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal-is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1946

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor—including metal, mineral, and fuel technicians—to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support. In Latin America, as elsewhere, this support applies in three categories: banking, procurement, and technical assistance. The first two are now generally accepted as necessary Government functions; the third has often been misunderstood and misinterpreted, although it has given rise to legitimate controversy. There have been major accomplishments in all three categories, as well as some errors of judgment. Since the beginning of World War 11, U. S. Government financing, procurement, and technical assistance have been applied on a large scale to a wide range of commodities and services throughout the free world. The present discussion—under the separate headings mentioned—will concern only the support related to a single industrial group in a single geographic area. During the War Federal banking was conducted on an emergency scale by temporary agencies created to meet the abnormal circumstances. Unfortunately, there are no readily available data on these activities that would permit evaluating loans and credits extended for mineral projects in Latin America. The only agency operating in this field since World War II is the Export-Import Bank, under its own authority and to some extent from credits authorized by the Office of Defense Mobilization. The Bank can offer more capital—on more favorable terms—than is available from most Latin American banks, and its staff of engineers evidently can appraise loan applications more favorably than commercial banks in this country are willing to do. The risks seem to be justified, as defaults have been well under 1 pct of total loans. From V-J day 1945 to the end of 1957, mineral loans to Latin America have been authorized for projects totaling $541.63 million in eight countries. In order of magnitude of credits, they have been made to Brazil, Peru, Chile, Mexico, Argentina, Venezuela, Guatemala, and Bolivia. In order of magnitude by industries. they are for development and expansion of steel mills, copper, manganese, nitrate plants, iron ore, zinc plants, sulfur plants, cement plants, tungsten, coal, and lead. Loan Distribution: By far the largest loans have been $307.9 million for iron and steel projects in Brazil, Chile, Mexico, Argentina, and Peru: $100.4 for developing the great low-grade copper deposits of southern Peru; and $55.3 million for developing manganese deposits in the Territory of Amapa, Brazil. Others range from $20.8 million for a zinc smelter in central Peru to $19 thousand for iron-mine trucking equipment in Chile. It has been noted that 59 pct of the loans have been to foreign companies, 14 pct to companies of mixed foreign and American capital, and 27 pct to American mining companies. About 40 pct of the total authorizations has been disbursed so far. In addition to these amounts, the Strategic Materials Division of the Economic Cooperation Admin-

Jan 1, 1959

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By David B. Brooks

Identified potential resources of lead and zinc are lower, relative to reserves, than the same ratio for other metals, Either there is little material below present grades or, if it exists, there are no data on it. The author examines both these factors in detail, and also introduces a third possibility. In their 1961 monograph, The Future Supply of the Major Metals, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.' Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vast quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.'12 This situation, which they called "the lead-zinc anomaly'' has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative. There are at least two reasons for devoting time to the lead-zinc anomaly. First, while it is unlikely that we shall have to turn to alternative lead or zinc resources in the near or middle-term future, the longer run resource picture for the two metals is not so certain.3 Both within the United States and for the world as a whole, new discoveries will have to come at a fair pace to keep up with growing rates of consumption. Thus, it is important to see whether there exist lower grade or nonconventional potential sources of two such useful metals that we could turn to at some time in the future. The second reason for studying the lead-zinc anomaly is also related to resource adequacy, but is of more general significance. Depending upon whether the anomaly is technologic, geochemical, spatial, or temporal in origin, we shall be able to draw some conclusions about the resource picture for other metals. Can we expect the apparent pattern of lead-zinc resources to be repeated? If so, will technologic advances in either exploration methods or mineral processing be able to alter the pattern? Or is the pattern unalterably set by geochemical distribution? Most important, are metals characterized by what seems to be an anomaly, different in any way from metals for which low-grade or nonconventional sources already have come to be exploited, as the porphyry deposits have for copper. In sum, investigation of the lead-zinc anomaly represents a case study combining both physical and economic aspects that may open up a neglected area in evaluating mineral resource adequacy. WHAT IS THE LEALLZINC ANOMALY? There are two dimensions to evaluations of the potential of any mineral resource? The first involves the degree of certainty that we ascribe to the estimate: how much do we know about the size of the resource as a result of geological mapping, exploration, and mine development? This dimension is expressed by the terms measured, indicated, and inferred reserves (and, if you wish, 'undiscovered reserves'), all of which terms carry with them the implication of exploitability under current cost-price conditions. The other dimension to evaluations of a mineral resource involves the economic limits of the estimate: how will the size of the resource vary with different (usually more favorable) cost-price conditions? (This economic dimension should be understood broadly to include all factors bearing on the cost-price relationship. In this sense it subsumes technology because any resource is exploitable at some cost; the role of technology is to bring cost down.) The latter dimension is expressed in the terms potential or sub-marginal 'ore,' and is logically quite independent of the former. For example, we have relatively good measurements of the tonnage of manganese in low-grade deposits in this country, though they are too lean to be considered reserves; on the other hand, we are much less certain of our measurements of new lead and zinc deposits in Missouri, though there is no question but that there is a sizable reserve. Thus, it may be uncommon but is not a contradiction to talk of measured submarginal ore or inferred potential ore.

Jan 1, 1968

A. R. Ledoux,New York City: The so-called combination method " is generally used in assaying bar copper for silver. It has been modified from time to time. Briefly outlined

Jan 1, 1901

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1940 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which was issued quarterly in 1940 but will be issued every other month in 1941. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CONTRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute accord-ing to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICA-TIONS will be sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1.25 domestic, $1.35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2.50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7.80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum domestic, $6.60 foreign (metal mining, milling and concentration, Industrial Minerals Divi-sion, and mining geology papers.) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6.60 foreign. Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and he may purchase for $2.50 one copy of a volume not already received; additional copies of the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 50¢ each to members; to nonmembers 506 current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4.00 foreign.

Jan 1, 1940

By JAMES J. DOUGHERTY

THIS paper is a general discussion of developments in our reverberatory smelting practice during the past five years. It deals briefly kith changes in furnace types ; changes in furnace feed ; de- crease in the amount of slag produced; relation of slag assays to copper loss in the slag; increase in the grade of matte and furnace capacities. The reverberatory is but one unit in the copper plant ancl 'any discussion of it must be considered with reference to the other units and to the plant as a whole. A change in the grade of concentrates at the concentrator puts an entirely new aspect on reverberatory smelting and, likewise, a change in the grade of matte at the reverberatory affects the rate and cost of converting. The introduction of differential flotation in 1927 had a very marked influence on all smelting operations and its effect will be noted

Jan 1, 1930

By Hans Lundberg

N OT so long ago, the discovery of an orebody took place only by accident. At the present time mineral deposits, even though concealed, may be revealed by their physical or geophysical characteristics, considered in connection with geological studies. Geophysical methods are based on sound, scientific principles and in no sense partake of the mysteries of "divining-rod " methods. Geophysical methods are divided into two main groups: Group I: Methods where fields of force surrounding mineral deposits are investigated (magnetic, gravitometric, electric) ; Group I1 : Methods where fields of force are applied (produced) and anomalies caused in these fields by mineral deposits are recorded (electric, seismic). By methods belonging to Group I, the investigation of the fields of force may be brought to an astonishing degree of accuracy by means of highly sensitive and delicate apparatus (torsion and magnetic balances) ; at least, in simple cases these methods have proved to be of great value.

Jan 1, 1925

By J. L. Tokich, A. R. Troiano

INTRODUCTION SINCE 1921, when Hull' discovered that cobalt can exist in the face-centered cubic and hexagonal close-packed modifications, the transitions that occur in cobalt have been extensively studied. It is generally agreed that on heating the hexagonal lattice changes to the cubic structure at temperatures ranging from 400 to 500°C although considerable doubt exists as to the exact temperature. Data concerning the temperature of the transformation on cooling are much less concordant and their interpretation has not been satisfactory. The study is further complicated by the fact that many investigators have reported the existence of a high temperature allotropic change in the range 850 to 1020°C, at which the cubic lattice reverts to the hexagonal modification. The transition on cooling, which has been reported as occurring at various temperatures from approximately 400 to 100°C, is of particular interest. Troiano and Greninger2 have recently suggested and considered the possibility of allotropic transformations occurring in pure metals by a shear-type, diffusionless (martensite) transformation. The case of cobalt was specifically discussed and certain observations of previous investigators evaluated in terms of this type of transformation. Table 1 briefly outlines the methods and results of previous investigators of the transformation temperatures of cobalt. MATERIALS AND METHODS The major portion of this investigation was performed with cobalt sheet containing a total of 0.2 pct impurities with carbon present to the extent of 0.1 pct. After melting in an induction furnace under an atmosphere of hydrogen, the carbon content analyzed 0.03 pct. Some observations were repeated with hydrogen reduced cobalt compresses analyzing 99.9 pct pure. No significant variations in results were observed employing the as-received sheet, the remelted stock, or the cobalt compresses. Filings for X ray diffraction analysis were sealed in evacuated glass ampoules. Pyrex glass tubing was used for temperatures below 600°C and for higher temperatures clear fused quartz was satisfactory. After appropriate heat treatment at various temperatures, the specimen ampoules were furnace cooled, air cooled or quenched by crushing under distilled water. This allowed a range of cooling velocities from less than one degree C per sec to greater than 1,000°C per sec. X ray diffraction patterns were taken with a Debye camera and filtered characteristic cobalt K-alpha radiation. The proportion of the existing phases was roughly approximated by visual examina-

Jan 1, 1948

By John B. Hastings

THE occurrence of such a large amount of gold in the Hartsel granite, even though the surmised existence of similar areas is not new, brings freshly to mind the pegmatite type of magmatic differentiation lately brought again to attention by occurrences at Silver Peak, Nev., described by Spurr; and in Alaska, described by both Spurr and Brooks. In both localities graunitic rocks or dikes are thought to pass into metalliferous quartz-veins. An interesting association in this connection is the occurrence of diamonds in residual pegmatitic clay of San Juao de Chapado, Brazil, described by Derby :1 (P. 142) "Bodies of pegmatite are quite common in the older rocks of Brazil, both in the. diamond regions and elsewhere, occurring not only in the gneiss and granite, but in the schistose series as well. Those that have been examined are dike-like in their mode of occurrence and granitic in composition." (P. 143) "The question of the eruptive or secretionary origin of pegmatites has long been a subject of discussion among geologists. . . . The recent studies . . . seem to have clearly established that most if not all of them are essentially eruptive masses, though possibly modified in some way by aqueous agencies. Even before becoming acquainted with the literature of the subject this view had seemed to me to be the only acceptable one as regards the typical pegmatites of Brazil." What is pegmatite ? J. F. Kemp says ". . . veins or dikes-it is an open question which is the more correct term-are met formed of very coarsely crystalline aggregates of the same minerals that constitute granite. These are called pegmatite and in them is the home of graphic granite, the curious intergrowth of quartz and feldspar, such that a cross fracture of the blades of quartz suggests cuneiform characters. . . . In regard to the larger veins or dikes it seems improbable that true igneous fusion could have afforded such coarsely crystalline aggregates, and so we are forced to assume such abundance of steam and other vapors, i.e, mineralizers, as to almost, if not quite, imply solution."

Jan 5, 1908

By Donald J. Worth

INTRODUCTION Minera Real de Angeles makes a very interesting case study in more ways than one. To begin with, it represents the first time a bulk silver deposit has been put into production in Mexico. Second, the feasibility and financing stage spanned a period when the silver price ranged from $4 to $40 per ounce. Third, there was a major devaluation of the peso and a financial crisis in Mexico at completion of the project. Fourth, the composition of the partnership (a major Canadian mining company, a major Mexican mining company and the host government's own mining entity) is worthy of note. This paper gives considerable background on the project and how it came to fruition. The political risk aspects and how the major provider of funds perceived Mexican risk at the time of decision to participate and afterwards are highlighted. LOCATION AND HISTORY The Real de Angeles deposit is located at an elevation of 2300 meters in Central Mexico in the State of Zacatecas (Figure 1). The closest village is Noria de Angeles, three kilometers to the north. The closest cities are Aguascalientes, Zacatecas and San Luis Potosi. The first-mentioned is one hour to the southwest by automobile over good roads. Exploitation of the vein outcrops probably began towards the end of the sixteenth century by the Spanish. Evidence of past mining activity is shown by numerous shafts, manways, dumps and ruins. Also, there were remnants of two rudimentary concentrating mills now obliterated by pit development and in the nearby town of Noria de Angeles the ruins of a small smelter still exist. Compania Minera Gamma, an affiliate of a major international mining company, investigated Real de Angeles from 1969 to 1971. Its evaluation program included 20 drill holes and comprehensive geological engineering and metallurgical studies. The results were not encouraging and the option on the property was dropped. In late August 1973 geologists representing Placer Mexicana which was later renamed Explomin were advised of the availability of the property and liked the prospects sufficiently to make an option payment soon due and to agree to outright purchase by year-end. A series of 34 holes were drilled by Explomin and a preliminary study indicated that the prospect had mine-making potential if the silver price was right. [ ] DESCRIPTION OF THE PROJECT Real de Angeles is best described as a large, low grade open pit silver mine because at today's prices approximately 70% of the realizable revenue is derived from that metal. One must also keep in mind that the operation produces two concentrates - a lead concentrate with high silver content and

Jan 1, 1985

By AIME

WE got our chance to talk with Arthur J. Blair at the Annual Meeting at the Pennsylvania Hotel. By two o'clock Wednesday afternoon things had quieted down enough so we had our interview in the foyer to the Ball Room. There were the usual questions. Where were you born? In La Salle County, Ill., on March 26, 1885. Where did you go to school? Northwestern University, B.S. degree in 1906. Where did you start work? For E. J. Longyear right after leaving school. One's ability as a geologist was measured by one's ability to wield a brush hook and ax. He stayed on the job as geologist for three years and then got to thinking about the advantages of a warmer climate. The advantages stacked up favorably, so off he went to Birmingham, Ala., just about the time U.S. Steel took over the Tennessee Coal, Iron and Railroad Co.

Jan 1, 1948

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

By John J. Cioston

THE steadily rising flood of gold production from all parts of the world has created an avalanche of rumors regarding the stability of the present price of this metal. Markets have been unsettled from Johannesburg to London from New York and Toronto to Melbourne, despite repeated denials from, American and British authorities of any immediate intention to alter the price. Various economists and financial writers have blossomed forth with predictions that the price would be set at the old level of $20.67 per oz.; some have even been so brash as to state That a price of $15 would be necessary to bring production within control. These effusions, based entirely upon monetary theories and with no regard to production costs, serve to confuse rather than clarify the situation.

Jan 1, 1937

By George Steintveit

Det Norske Zinkicompani A/S was established in 1924, on the initiative of the Compagnie Royale Asturienne des Mines. Experimental electrothermic zinc production was carried out on industrial scale for a two-year period, but the problems of electrothermic smelting were not solved. A license for the electrolytic zinc production process was then obtained from the Anaconda Copper Mining Co. A plant for electrolytic zinc production was built, near the small fjord town of Odda in Hardanger, West Norway, The production was based on zinc ore from Spain, and cheap local hydro-electric power. The plant came into operation in 1929. Annual capacity, 36,000 tons. In 1964 a long-term agreement was concluded with Boliden AB by which Det Norske Zinkkompani is secured the raw materials basis for an expansion of the annual capacity to 100,000 tons of zinc, Since World War II, the company has been pursuing extensive research and development programs. As a result, various sections have been rebuilt: nev unloading and storage facilities, a 250 ton per day Fluid Bed Roaster with contact plant, new continuous leaching system, integrating the Jarosite Residue Process, new solution purification section - upgrading the solution quality for a 600 Amp/m2 current density Tank Room operation -, installation of induction furnaces for cathode melting with casting machines and automatic stacking of slabs. Simultaneously, instrumentation, and methods of automatic control have been developed and introduced, providing conditions for optimal plant operations.

Jan 1, 1970

Jan 1, 1967

Coal production during 1963 amounted to 446 mil- lion tons, an anticipated increase of about 6% over the 1962 production of 422 million tons. Electric consumption was 207 million tons, a continuation of its upward trend with an increase of about 7%. The metallurgical market consumed 77 million tons: the industrial market, 96 million tons; and the retail market, 26 million tons. Exports were 46 million tons. Modernization continues in the coal industry as it approaches the mid-1960's. The industry has shown a keen desire to explore and pursue new developments, new concepts and new managerial methods and techniques that have become so vital and important for industrial well-being.

Jan 2, 1964