Search Documents

By Edmund C. Pechin

THE writer approaches this subject with a great deal of diffidence —first, because it is utterly impossible to treat it satisfactorily within the limits of a paper, and, secondly, because the larger development is of so comparatively a recent date as to make authoritative data on some interesting points unavailable. For over one hundred years small charcoal-fnrnaces have been in existence, at widely scattered points, making a few tons of iron daily, and then gradually increasing to a daily output of, say 10 to 12 tons, as the market widened. With the exhaustion of local supplies of wood, inaccessibility to market, and sharp competition, bringing lower prices, many were compelled from time to time to make temporary stops, and finally to cease altogether. During the first half of the century there were at different times in operation between 75 and 90 charcoal furnaces. The last Directory of the Iron and Steel Works of the United States (1890) gives 19 as the number of charcoal-stacks in Virginia. Of these several are cold, and, it is

Jan 1, 1891

By W. F. Boericke, T. H. Garnett

The Wisconsin zinc district, or the Upper Mississippi lead and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies country in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, withroads, railways, streams, and the various towns, or "camps," around which the mines are clustered. The hatchwork indicates the areas in which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zoncs of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. ease or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within comparatively recent time been worked intensively for zinc, the chances are good for opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However; the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Ben-ton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland. The district is one of the best farming districts in Wisconsin, with deep fertile soil. The farms are large and well improved, and the towns are modern and prosperous. Railroad facilities are good and proximity to Chicago is an asset. Mining is usually done on a leasing system of 10

Jan 1, 1920

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By JOHN R. SUMAN

IT SEEMS particularly appropriate that the Institute's Regional Meeting should be held in Minnesota this year. Whether we like it or not, we cannot help looking at things now in the light of the World War and the all-out effort we, as a nation, are making to defend our resources, our institutions, and our way of life. The ability to do this lies in large measure in the ability to forge weapons of defense-the machines of war. The basic ingredients of any defense system, or war machine, are the raw materials of industry-iron ore, providing steel for guns, shells, tanks, and warships; coal for stoking the nation's furnaces; oil to furnish power for war planes, ships, trucks, and mechanized weapons; and all the other materials that play a vital role in the operation of modern armies and navies. The tremendous requirements of full-scale defense programs are indicated by the large number of commodities that are now under priorities because the supply is not sufficient to meet both defense needs and all normal civilian consumption. But out of all these items two are of paramount importance-steel and petroleum. In this age no nation can hope to main¬tain a position as a first-class power in the world without a highly developed industry, particularly the heavy industries based on steel, and without access to the necessary resources for those industries. In 1918, 70 per cent of the iron and steel production of the United States was required for defense purposes. In 1940, 15 per cent of our iron and steel production was consumed for defense purposes, and with the acceleration of the defense program, it appears that the proportion of steel output required for defense purposes will reach 40

Jan 1, 1941

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By T. M. Girdler

INDUSTRIAL progress and development in this country from the earliest daps to the present has proceeded at an ever-quickening pace. Yet during recent decades the nature of our industrial progress and development has undergone a change of great significance. The earlier days were a period of tremendous expansion. Population was increasing by leaps and bounds. Vast areas of new land were being .2 opened to settlement. And almost boundless new sources of timber, coal, oil, ores, and power were being opened to ever-expanding markets. Today, however, that picture has al- most completely changed. Today, with population increase tapered way off and the opportunity for free expansion into western frontiers gone, the great industrial development of our country continues on a vastly different front. Industrial progress and development today rest on a foundation of technology. The key- stone is research. Our frontiers to- day are frontiers of sciencec

Jan 1, 1939

By L. W. Berger, R. I. Jaffee, D. N. Williams

The effects of hydrogen on the properties of binary Ti-A1 alloys containing 2.5, 5, and 7 pct aluminum and ternary alloys of the same compositions with added interstitial elements oxygen, nihrogen, and carbon were studied. Aluminum increases the apparent hydrogen solubility of the a-phase, resulting in a marked increase in resistance to impact embrittlement. In the Ti-5Al and Ti-7Al alloys, for example, the addition of 180 and 305 ppm hydrogen, respectively, did not cause embrittlement, while unalloyed titanium was embrittled by as little as 75 ppm. The role of aluminum in increasing hydrogen solubility of the a-phase probably accounts for the excellent hydrogen tolerance of a-ß alloys containing considerable amounts of aluminum. There is some evidence that aluminum retards the rate of hydride precipitation. If so, these alloys may be susceptible to slow-strain embrittlement. UNALLOYED a-titanium is extremely sensitive to small amounts of added hydrogen in that there is a marked decrease in notch properties. For example, as little as 100 ppm hydrogen is sufficient to lower the room-temperature notch-impact strength from over 100 to less than 20 in.-lb.' This loss of impact Strength has been associated with the Presence of hydride phase in the microstructure. Hydrogen in the amounts encountered in commercial practice

Jan 1, 1959

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By Thomas J. O’Neil

From the time of its emergence as an independent state until the late 1950's, the Republic of Ireland suffered from chronic unemployment, the lowest living standard in Northern Europe, and-most serious of all-an aggravated emigration problem which drained off most of its talented young people. In 1958, however, there was a drastic legislative reaction to these problems, and this in turn ignited the current mining boom in Ireland. Paving the Way to Prosperity In order to reverse the tide of emigration, the Irish government now realized, challenging domestic employment opportunities had to be increased and living standards had to be raised. It was also apparent that future industrial and economic growth in Ireland had to be based on producing goods for export. The home market could not sustain large-scale expansion, and consequently Ireland's chronic balance-of-payments deficit could best be minimized by producing export goods. These considerations, together with the limited amount of accumulated wealth in Ireland, combined to set the objectives of the country's First Program for Economic Expansion in 1958. The general objectives of this program were (1) to stimulate all segments of the economy, (2) to develop foreign trade and (3) to attract foreign capital.

Jan 1, 1970

By William Y. Mo

The OPEC oil embargo and the subsequent higher prices for oil have drawn public attention to the critical problems associated with security of supply of oil and other key industrial materials, especially nonfuel minerals. This concern has stimulated the interest of decisionmakers in analyzing policy options to cope with the emergency situations resulting from a sudden foreign- induced supply interruption or a cartel price increase. Several policy options are available to counteract foreign-initiated embargoes or cartel price actions. The type of response will differ depending on the commodity action intiated. A mathematical model that measures the impact of foreign-induced commodity actions on the domestic economy is formulated. The paper also presents a computer method that can be used to determine the optimum policy response to counteract such actions.

Jan 1, 1977

INTRODUCTION IT is 10. years this summer since the first of the contributions which it has been my privilege to make to the working tools of the hydrometallurgist was set at work, but a full description of what has come to be known as "Dorr Machinery" has never been published in the Transactions of the Institute, and it has been suggested to me that an account of the same would prove of interest to members, although most of those engaged in cyaniding and concentration are probably familiar with it. The account which I shall give of the development of the machines must be recognized as being written from the viewpoint mainly of my own local experience and not from that of one who was familiar with the general metallurgical practice throughout the world. Most advances in any art are conceived before the time is ripe for their development and any .invention which comes into general use will usually be found to have been tried out in a crude way and abandoned more than once. If the early experimenter went as far as the Patent Office, his work may serve no other purpose than to prevent the issuance of the broadest patent to those who later may develop a commercial process. The cyanide process in the United States early in 1904 was mainly confined to the leaching of dry crushed ores, both coarse and fine, and sand treatment of tailings from concentration and amalgamation. In the Black' hills some plants were crushing in cyanide solution, leaching sands and handling the slime by the well-known decantation process. Filter pressing, in use for some years in Australia,had been tried in several places in this country and the Moors process had been abandoned at Mercur after' a short run, but was doing good work at the mill of Lindbergh, Dorr & Wilson, at Terry, and being installed at Bodie and the Liberty Bell. A general feeling, however, still existed that, slimes were to be avoided when possible, on account of the losses in treatment and the difficulty of making a good leaching product when they were present in large amounts, especially when the crushing was done in cyanide solution.

Jan 8, 1914

By Harrison Souder

MAGNETITE mining and milling in the Eastern States showed continuing improvement during the year. Some of the smaller mines remained idle, but the larger operations responded promptly to the improved situation in the iron and steel industry. The output of ore for 1936 was over twice that for 1935. A number of improvements were made in mine plant and equipment, and operating forces were increased and maintained at near normal. The coming year should see additional mines started up and production increased at the larger properties.

Jan 1, 1937

By William Romanoff

IN AN ARTICLE on "Recovering Smelter Dust and Oxide," published in the Engineering and Mining Journal (Vol. 131, No. 2), the authors briefly described some dust-recovery equipment and its operation at a secondary-metals brass-smelting and refining plant. A description of our experience in overcoming certain operating difficulties may prove of interest or value to those who are confronted with some of the same problems or who should equip their furnaces with dust-collecting equipment. The dust loss from reverberatory smelting and refining of brass con¬sists largely of zinc, with smaller percentages of lead, tin, and copper in the order named. At the Kramer plant, the fume discharge from the two stacks amounted to 3 to 4 tons of solids per day, making a dense smoke. With dust equipment in operation, the discharge from the stacks is invisible and approximately 2500 lb. of zinc and other metals is recovered daily thereby from each furnace operating.

Jan 1, 1933

By L. D. Jaffe

IN previous metallographic work on titanium and its alloys, difficulty has been encountered in distinguishing spheroidal particles of titanium hydride, dispersed in a-titanium, from other phases that may be present, such as p-titanium. This problem is common in examination of commercial unalloyed titanium.' In the course of an investigation of the Ti-H phase diagram, it was noted that titanium hydride, dispersed in a matrix of a-titanium, showed strong optical anisotropy when examined under polarized light. With sensitive tint illumination, particles of the hydride, when the stage is rotated, changed from bright yellow to bright blue in color. Since P-titanium is cubic, it showed no color change on rotation, remaining dark gray or blue-gray. Although a-titanium is hexagonal, it showed only a minor color change, going from pale pinkish-blue to pale purplish-blue. These colors could be modified somewhat by adjustment of the illumination. They were observed in specimens mechanically polished, both without etching and after etching with hydrofluoric acid-nitric acid mixtures in either water or glycerine. The strong color change of the hydride seems to offer a simple method for its metallographic identification. Optical anisotropy of titanium hydride is inconsistent with its accepted face-centered-cubic structure.' Samples of iodide titanium containing 6 to 40 atomic pct deuterium were prepared for diffraction studies. After deuterating and slow cooling' the samples were held 21 % hr at 400 °C, water quenched, held 61 hr at 100°C and quenched, then held 64% hr at 255 C and quenched. Debye ex-posures with MoKa X-rays and 1.111A neutrons were made at room temperature of samples as-deuterated and after the 100" and 255°C treatments. Table I shows the lines observed, in addition to those attributable to a-titanium. These data show that the hydride phase was not cubic, but probably tetragonal. The titanium atoms appeared to form a body-centered-tetragonal lattice complex, two titanium atoms per cell, with approximate dimensions: a = 3.12A, c = 4.18A, and c/a =1.34A. This is equivalent to a face-centered-tetragonal complex, four titanium atoms per cell, with approximate dimensions: a = 4.42A, c = 4.18A, and c/a - 0.946A. The presence of the 2.98 and 1.81A neutron lines indicates that the true Bravais lattice is not identical with this lattice complex, but may be primitive tetragonal with dimensions some multiple of those of the complex. The relative intensities of the hydride and a-titanium X-ray lines as functions of overall composition indicated that the hydride, presumably in equilibrium with the a at 100" to 255"C, contained more than 62 atomic pct H. Acknowledgments The experimental work covered in this report was done at Brookhaven National Laboratory, through the courtesy of D. Gurinsky. The cooperation of J. Sadofsky, 0. Kammerer, A. McReynolds, and A. Cendrowski is gratefully acknowledged.

Jan 1, 1957

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating." The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By George C. Coupland

Ecstall Mining Limited, a wholly owned subsidiary of Texas Gulf Sulphur Company, is the owner and operator of the Kidd Creek Mine including the concentrator complex located near Timmins, Ontario. Canada, approximately 450 miles north of Toronto. The mine, concentrator and Timmins form a triangular arrangement with a 17-mile rail link connecting the mine and concentrator and both of these facilities 18 and 14 miles respectively by road from Timmins. A core drilling program in the spring of 1964 established the presence of a large massive sulphide orebody which was to become the Kidd Creek Mine. Texas Gulf Sulphur had been conducting an intensive search for base metal in various parts of Northern Ontario and Quebec since 1957. Of several thousand anomalies detected in airborne electromagnetic surveys, several hundred warranted ground inspection, but only one of more than sixty drilled became a commercial orebody, the Kidd Creek Mine. The geophysical exploration work has been well covered in a paper written and presented by Van Donohoo, presently a Vice-President of T.G.S., at the American Mining Congress in San Francisco in October 1969. GEOLOGY The orebody lies within a series of overturned rhyolitic flows and pyroelastics with a major peridotite intrusive to the east. The hangingwall and footwall are composed chiefly of intermediate volcanics, andesite and dacite. The southern end of the orebody appears to terminate abruptly against greywacke while the north end is bifurcated and the structure obscured.

Jan 1, 1970

By L. R. Weisberg, E. A. Miller

Single-crystalline films of silicon of good quality were vacuum-deposited on sapphire. The improved crystallinity was achieved by the strict exclusion of oxygen from the evaporation system, including the use of a "oxygen-free" silicon source. To minimize possible contamination of the source, the silicon was sublimed from the solid at about 1390° C. using a simple electron bombardment system to heat the silicon. This resulted in deposition rates of about 5 to 7 µ per hr and film thicknesses of 4 to 20 µ. The vacuum during deposition was ordinarily about 5x 10-8 Torr, DESPITE the success achieved in the chemical vapor deposition of silicon on sapphire using Silane,1-4 vacuum deposition has not provided comparable properties. For example, Chu et a1.5 vacuum-deposited silicon on single-crystalline substrates of A12O3, Sic, ThO2, and other compounds, and, although some epi- but the use of ultrahigh vacuum (about 1 to 3 x10-9 Torr) during deposition did not significantly improve the results in the oxygen-free system. The crystalline quality of films deposited on (0001) sapphire was found to be considerably superior to (1102) sapphire surfaces. Using (0001) sapphire, single-crystalline films were deposited at temperatures as low as 780° C and as high as 1075°C, with the best crystalline quality obtained at about 1000°C. At this temperature, hole mobilities over 250 sq cm per v-sec were achieved. taxy was indicated, single-crystalline films were not produced. More recently, Salama, Tucker, and young6 evaporated silicon on single-crystalline sapphire, but only poor crystallinity was observed, and low carrier mobilities were measured. In the present experiments, good-quality single-crystalline films of silicon on sapphire have been achieved by specifically excluding oxygen from the evaporation. This included not only the use of a "clean" vacuum system but, of special importance, the use of an oxygen-free silicon source. This has also been shown to provide a dramatic improvement in silicon homoepi-taxy.7 As a result, silicon-on-sapphire films with hole mobilities over 250 sq cm per v-set were achieved, and single-crystal films were grown as low as 780°C and as

Jan 1, 1969

By Kenelm C. Appleyard

In introducing to an American audience a description of the work done in dry coal separation in England and in Europe generally, it is perhaps desirable to give a short history of the development outside the United States of the particular processes with which the author is connected, and perhaps to stress a little the differences in the nature of the conditions to be faced. England actually presents one set of problems and the Continent of Europe another, since the character of the coals to be treated is entirely dissimilar, and the attitude of the coal industries towards coal preparation is also dissimilar. England for generations has been working by hand good seams of clean coal of the highest possible quality and has not felt any pressing need to clean its coal. Most Continental countries, however, especially in Central and Western Europe, have been working friable and often very dirty coals for so long that a washery is accepted as a part of the normal equipment of a colliery, with the result that the art of wet washing has reached a high state of perfection, particularly in Belgium and Germany. The advent of machine mining has intensified the problems to be faced in all countries, and in England has been coupled with the working out of the best seams in the older coal fields, thus bringing about the necessity of working thinner and dirtier seams with resultant difficulties as regards marketing the products, while Poland, with clean and well prepared coal, has in recent years been attacking established British markets in Scandinavia. In recent years, therefore, interest in coal preparation has been steadily gaining ground in England, although it has not yet reached Continental dimensions. Broadly speaking, the differences in preparation problems between England and the Continent boil themselves down to one of size. In England, for example, with the exception of the Kent coal field, the proportion of coal of a size less than ? in. to the coal less than 2 in. is very much less than on the Continent, and since the principal difficulties in dry cleaning lie in the fines it is easier to produce good figures on

Jan 1, 1931

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10'* sec-'). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.' Several investigators'-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.' From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800' to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By Francis Church Lincoln

I. SITUATION AND SURROUNDINGS. THE Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chinacates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the station by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion-a distance of about 15.5 miles-and then entering the mountains crosses the Sierra to Promontorio-a further distance of 11.5 miles¬making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Ives, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Melchor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-July, August and

Jan 1, 1908