Search Documents

By Gilbert L. Eggert

The effects of reactor irradiation on age hardening in a Cu-2 wt pct Be alloy have been investigated in two neutron-energy ranges. During some of the irradiations, specimens were exposed to high-energy fission neutrons which passed through a boron-10 shield; during other bombardments, the boron-10 was omitted and specimens were irradiated in a reactor thermal column, or the fuel configuration was modified to increase the thermal-neutron flux at a location in the core. Differences in length, X-ray diffraction angle, and hardness indicated that low-energy neutron irradiation made a small contribution to changes in the measured properties. The influence of defects generated by knock-om with less than the Brinkman critical energy or by prompt (n,y) recoil is suggested as the cause of this effect. EXPERIMENTS designed to test the effects of reactor irradiation on the properties of age-hardening alloys have to the present time employed fluxes un-differentiated according to neutron energy. Billing-ton and Siegell in 1950 were the first to perform such an experiment and to compare the results with those obtained by thermal aging. These authors concluded that precipitation in a Cu-2 wt pct Be alloy was not enhanced by the radiation. However, 4 years later, Murray and Taylor,2 working with specimens of the same Cu-2 wt pct Be alloy, reported that an increase in density, hardness, and resistivity which followed reactor irradiation resembled changes associated with thermal aging at about 100°C. (It should be noted that these authors reported that higher aging temperatures caused a decrease in resistivity.) cupp3 reported hardness results similar to those of Murray and Taylor. Koppenaal4 showed that irradiation-enhanced precipitation and irradiation defect hardening were not simply additive but that they acted separately in an irradiated alloy. Kernohan et a1.,5 working with Ni-Be, offered evidence that beryllium was removed from solid solution by reactor irradiation and suggested that the mechanism was one of increased diffusion through the use of vacancies in the structure. piercy6 also found that more precipitate particles were formed by fission-neutron irradiation of a Cu-Co alloy which contained a small amount of particles before irradiation. He proposed that the additional particles were caused by an appreciable amount of diffusion during the final cooling of displacement spikes. The retrogression of extant precipitate particles found by Murray and Taylor2 and Boltax7 as well as piercy6 indicated that nuclei were dissolved within a high-energy spike region and, upon resolidification of the perturbed volume, new nuclei precipitate and grow by enhanced diffusion. Bleiberg et al.' and Konobeevski et al.' explained phase changes obtained by irradiating fissionable alloys in terms of retrogression and re-precipitation in regions of high-energy spikes. Parsons and Balluffi10 used electron microscopy to verify that crystallization did indeed occur in displacement spikes which were formed in amorphous germanium by fast-neutron irradiation. The concept that low-energy neutron irradiation might cause structure-sensitive property changes in semiconductors by atomic recoil associated with the (n, y) reaction was first proposed by Schweinler" and walker." This thesis was tested by Cleland and crawford" and found to be valid. Coltman et al.14 exposed a variety of pure metals to thermal-neutron irradiation at cryogenic temperatures and attributed the resulting resistivity changes to the action of defects created by (n, y) recoil. The present work was undertaken to extend the concepts of Schweinler," walker," and Coltman et al.I4 to the case of an age-hardening alloy and to determine whether or not the action of defects produced by thermal-neutron irradiation would en-hance age hardening. EXPERIMENTAL PROCEDURE Omeea West Reactor Irradiations.* Thermal-

Jan 1, 1965

By E. J. Kenaedy, E. H. Robie

THOUGH the fall meeting of the Coal Division was held in the heart of the anthracite section, at Hazleton, Pa., the bituminous industry was well represented also, and the two groups found much common ground for discussion. The' technical part of the program was confined to two sessions in the morning and afternoon of the first day, Friday, Oct. 14, the evening and the following day being reserved for field trips and social functions. The attendance more than met the expectations of those in charge of the arrangements; there seemed no hint of depression here.

Jan 1, 1932

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950

By Elton A. Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11. mile bus ride up Railroad Creek to Holden. A11 freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting. Ore is broken by long-hole blasting using the Noranda system which has been modified to meet local conditions. Until recently, blastholes have been drilled by diamond drills. Now a partial substitution of percussion drill holes, drilled with tungsten carbide insert bits, is being made. Geology The ore body occurs as a replacement deposit in a highly metamorphosed series of sedimentary rocks, mainly gneiss and schists, in a shear zone several hundred feet in width and of undetermined length. Commercial ore has been found in mineable widths of 25 to 100 ft for approximately 2500 ft along its strike. The commercial minerals are chalcopyrite, sphalerite, and gold. During the period of mineralization considerable silicifica-tion took place giving the ore an abrasive drilling characteristic. Following the period of mineralization, numerous dikes were introduced into the ore body. The earlier ones were of granite composition having a width of a few inches up to 80 ft. These were followed by much younger, fine grained basic dikes which usually do not exceed 2 ft in width. Development of Percussion Blasthole Drilling Equipment Test work with the 1½-in. tungsten carbide bit was carried on in development headings for several months early in 1947. The short life of the bits, because of gauge loss caused by the abrasive nature of the rock, prevented its adoption for this use. However fast drilling speed and ability to drill a long uniform hole suggested its use for drilling blastholes in competition with diamond drills as diamond costs were steadily increasing and exper-ienced drillers were difficult to obtain. The 1½-in. bit was the largest available at the time initial test work was started with sectional steel. The 1½-in. hole limited the diameter of the steel thread and coupling which could be used. Type F couplings were first used but because of the small thread section excessive breakage of the steel was experienced. Type H couplings were tried next. In order to use this coupling which is 15/8 in. in outside diameter, it was reduced to 1 3/8 in. giving 1/8 in. clearance between the coupling and the hole. Rod breakage at the thread was substantially reduced but some coupling breakage was experienced, however the overall performance was considered satisfactory (see Fig 1 for illustration of coupling and thread). Early test work with the 1½ in. bit indicated machines of piston diameters larger than 255 in. would cause inserts to loosen or break. It was found however that the additional weight of the sectional steel cushioned the blow enough to prevent bit failures when 3-in. Leyners were used. Rods used with the 1½-in. bits were 7/8 in. q. o. for sectional steel and 1 in. q. o. for all chuck pieces. In May 1948, 2-in. tungsten carbide bits became available and test work was immediately started. The 2-in. hole approximated the AX (1 15/16 in.) diamond drill hole which was being used exclusively for blastholes and permitted their substitution for diamond drill holes in a ring without alteration of pattern, burden, or explosives. The 2-in. bit also gave room in the hole for larger couplings and permitted the use of heavier rods and 3½-in. machines, increasing the

Jan 1, 1950

By Walter Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

By John V. Beall

Never having done it before, it took us all day and until 11 at night to select and pack for a four-day back- pack trip up Lake Chelan last month. When we were through, we couldn't lift our own pack and Sylvia's, OUT spouse's, we barely managed to budge. Nevertheless, the next morning we were at the dock to board the Laldy of the Lake for the 3 ½ -hr boat trip to Lucerne. Our dress and accouterments creating the appearance of a veritable expedition into the wilderness made a sharp contrast with our fellow passengers, a senior citizens tour group from Spokane. We had come out to Seattle for the SME Fall Meeting and were taking advantage of the occasion for a vacation trip back to Lucerne and Holden where we had lived briefly 25-years ago, and a backpack trip up Railroad Creek from Holden to the Glacier Peak country, weather permitting. No matter what you say, weather is important, and this is one of the ingredients that went into making the SME Fall Meeting and Exhibit in Seattle, September 22-24, a thoroughly delightful experience for the 700 plus persons who attended. Seattle is a beautiful city, but with late September sunshine, which we experienced, it is the best. The second ingredient, is a swinging host committee. Under the leadership of Don Anderson and Tom Van Zandt, co-chairmen, and Mrs. Cecilia Reed, Ladies Program, superb hospitality and fine arrangements were blended. Earl Beistline, from Fairbanks, organized a two-day short course on arctic operations which preceded the meeting and drew an attendance of 44. Dick Robbins, in charge of arrangements, provided Masters-at- arms for technical sessions and a presentation of the colors by the U.S. Coast Guard at the Welcoming Luncheon. Eric Cheney's field trips ranged far and wide with events both before and after the meeting. David (Jeff) Kroft, capably managed audio-visual operations with a group of students from the University of Washington. Charles Hochmuth worked long, hard and effectively before and during the meet- ing on finances. Hank Reed, managed an authentic three-ring circus as Entertainment Chairman. His activities covered two cocktail receptions for all registrants and a dinner-dance. Dolph Campbell and Joe Hackbarth provided publicity by press and TV (see p. 37-40). SME's meetings have certain characteristics and possibly not all of these are known to everyone. The first of these is the deliberate involvement of the AIME Section in the area of the meeting. Most trade shows and conventions are run 100% by a professional staff and although SME staff could also do this, it has been our experience that a more friendly and better meeting results when the local members apply their talents. Actually SME only considers a site for a meeting after it has received an invitation from a Section. The knowledge of local conditions which Section committeemen bring to a meeting is of great value.

Jan 1, 1971

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4º; wet-bulb, 57.4º; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down- cast shafts; however, the variation between winter and summer causes a difference of only 2º to 3º in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of the mine are as follows: [ ] There appears to be no difference in rock temperature for any particular horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock temperatures given above is 1 ½ º per 100 feet. Underground Waters.-The underground water varies from 350 to 565 gal. per min., depending on the rainfall. The limestone and other

Jan 1, 1938

By E. A. von Hahn, T. R. lngraham

The rates of cementation of pd11 on electropolislzed copper cylinders were studied in aqueous perchloric acid solutions at pdII concentrations from 0.02 to 0.1 mM. The cylinders were rotated at various high speeds to reduce the diffusion layer to a minimum thickness. In 0.1 M HClO4 solutions, the cemented palladium is dense, adherent, and shiny. The rate data indicate that there are two stages in the deposition. In the initial stage, the rate of cementation is first order with respect to the pd11 concentration. The second stage is much slower. The first stage is consistent with rate control by the diffusion of pd11 ions to the copper surface, and/or chemical reaction at the surface, and the second stage is consistent with rate control by the diffusion of copper ions from the cop-per surface through the deposit of cemented palladium, out to the main body of solution. In 0.001 M HClO4 solution, only the first stage is evident and the rate is more rapid than at higher acidities. This rate enhancement is attributed to PdOH+ ions that predominate at low acidity and aye more reactive than unhydrolyzed pdII. The deposit is porous and loose. All of the cemented deposits are Pd-Cu alloys rather than pure palladium. Activation energies are 9.5 kcal per mole in 0.1 M HClO4 and 7.4 kcal per mole in 0.001 M HClO4. CEMENTATION or displacement reactions occur between aqueous solutions of metal salts and immersed metals according to the general equation: where M1 is electrochemically the more noble metal. Although these reactions find considerable application in metals recovery processes (e.g., the cementation of copper192 or gold3), in electrorefining processes (e.g., solution purification before electrolysis4,5), and in plating and metal finishing processes,6 few studies have been made of the kinetics of such reactions.7-9 The rates of cementation reactions will depend on one or more of the following factors: a) chemical reactions at the metal-solution interface; b) ionic transport to or away from the interface;'-' and c) the character and adherence of the cemented deposit on the substrate metal,6a,10 because the deposit will inhibit the rate of transport of dissolving ions (M2m+) into the solution. In this investigation, the kinetics of the early stages of cementation were studied to obtain an understanding of the reaction mechanism under conditions in which the deposit was sufficiently thin that its inhibiting effect could be disregarded. To achieve this, very dilute solutions in Mn+ were used. Cementation rates are often fast in the initial stages and transport-contr01led.9 To find conditions under which transport control would shift to chemical control, very high stirring velocities were used to minimize the diffusion-layer thickness. Of the many possible cementation reaction systems, the palladous perchlorate-copper system was chosen for this investigation because it was believed to involve simple ion-for-ion exchange. In addition, there are no interfering side reactions, such as the reduction of hydrogen ions, and anion effects are usually absent in perchlorate solutions. EXPERIMENTAL Materials. Reagent-grade chemicals and redistilled water were used in all experiments. Palladous perchlorate stock solutions (0.02 M) were prepared by dissolving 99.5 pct Pd sponge (Johnson Matthey and Mallory Ltd.) in concentrated nitric acid, adding concentrated perchloric acid, evaporating twice slowly (to prevent PdO precipitation) to a small volume, and diluting in a volumetric flask. To prevent gradual hydrolysis of PdII, the stock solutions were made 0.4 M in HC104. Tests for pdIV (Ref. 11) and C1- were negative. Copper strips were cut accurately from 0.025-in. electrolytic tough pitch sheet, Sample 1 (Mines Branch stock or Canadian Copper Refineries Ltd., Montreal), or from oxygen-free, high-conductivity sheet, Sample 2 (American Metal Climax O.F.H.C. brand, sold by Utility Brass and Copper Corp., Brooklyn). The strips were annealed for 1 hr at 335°C in a stream of purified nitrogen (Union Carbide, Linde Division) which had

Jan 1, 1967

By Edward S. Cook

For several years past, dating particularly from the days of serious "ore-dirt" complications at the Warwick furnace, I have been desirous of providing some safe, quick and easy method of relieving the tuyeres of slag, when the cinder- and iron-notches are chilled through loss of heat in the clucible or when, from dropping or jumping of stock, the molten slag is forcibly driven into the bellyand leg-pipes. Various methods were proposed, but objections of one kind or another always presented themselves, and the subject was postponed to a more convenient season. In the summer of 1887, while running on anthracite alone, 1 found the various expedients in use to be so utterly valueless, that the importance of a practicable tuyere slagging-valve impressed me more forcibly than ever. The holes left in the cast-iron jacket at one side of the bottom of the water-blocks were found to be of no value whatever. The swinging or hinged cap on the elbow of the belly-pipe, while convenient to permit the removal of lag after the belly-pipe was partially or wholly filled, could not be adapted to discharge the slag before solidifying, except at great risk to the men and loss of time just when the constant running of the engine and the keeping of blast on the furnace was of the utmost importance. By removing keys from the caps and holding them in place with props, the slag could be discharged through the tuyeres and belly-pipes, with the engine running, by knocking the props away at a given signal. This method is extremely hazardous to life and limb, and I have always hesitated to make use of it. When the furnace is in such condition as to require the adoption of some method of the kind, the stoppage of the engine, cooling the blast and the contents of the crucible, always aggravates the trouble. When the caps are blown open and the slag is discharged by removal of the props, it is necessary to stop the engine to replace them. An hour or more will elapse before this can be done, as the slag must be partly removed before the tuyeres can be approached by ordinary mortals, and the caps handled and fastened in place again. Any movement of the stock is liable to burn the workman, as he stands, securing the cap in front or at one side of the open belly-pipe.

Jan 1, 1889

Molybdenum was first discovered on the Continental Divide in Colorado in 19 11; and in 1918 two companies, one of which was the Climax Molybdenum 250 stpd operation, were producing. In 1919 both mines were shut down, but in 1924 the Climax mine reopened and has been producing ever since. Over the years mine production has been increased until today the mill capacity is 48,000 stpd (43,500 mtpd). From 1935 to 1973 all ore was mined underground by block caving with scraper slushing. Since 1973 ore production has been supplemented by open pit mining. As demand for molybdenum increased, upper levels of the mine became worked-out and new lower levels were opened. In late 1972 production began on the 600 level with the mined ore being primary and secondary crushed in the new No. 4 crushing station. Ore is hauled to the primary in 10 st (9. 1 mt) capacity Granby side-dump cars. The trains, carrying 200 st (181 mt), pass throug.h a dump block and discharge directly into a 54 in. by 84 in. Traylor TC gyratory crusher set at an 8 in. (203 mm) open side setting. Since the ore has already been broken to a size which will pass the finger raises in the mining areas, there are only rare oversize boulders to block the crusher opening. Selection of the crusher was based more on its capacity than its receiving opening, as is often the case with gyratories used in open pit operations. Nominal and maximum capacities for this unit are 1250 and 1800 stph (1 135 and 1635 mtph). The ore is often wet and sticky, so a mechanical car cleaning device is utilized. Under the crusher is a 300 st (270 mt) ore pocket equipped with a 60 in. (1.52 m) wide inclined conveyor which delivers the ore to a 2,000 st (1800 mt) surge bin. Near the head pulley of this conveyor is a wood picking station whe re tramp wood and steel are put into cars for removal. Two more apron feeders remove the primary crushed ore from the surge bin, and impact belts and conveyor belts transport the ore to the crushing station for screening ahead of two 7 ft (2. 13 m) standard crushers. Secondary crushed ore is then conveyed to the surface for tertiary crushing. The entire underground crushing room containing the primary, two secondaries, screens and related equipment is serviced by a 100 st (90 mt) crane with a smaller capacity fast hook. A control room is situated so the operator can observe all the crushing operations. Rotoclone collectors remove dust from the entire operation (including the fumes from the zinc pots) and discharge it to the final product belt. The Rotoclones are vented through drifts and raises to the surface. Shop facilities, electrical gear, and lubrication equipment are located

Jan 1, 1978

By M. King Hubbert, David G. Willis

A theoretical examination of the fracturing of rocks by means of pressure applied in boreholes leads to the conclusion that, regardless of whether the fracturing fluid be of the penetrating or non-penetrating type, the fractures produced should be approximately perpendicular to the axis of least stress. The general state of stress underground is that in which the three principal stresses are unequal. For tectonically relaxed areas characterized by normal faulting, the least stress should be horizontal; the fractures produced should be vertical with the injection pressure less than that of the overburden. In areas of active tectonic compression, the least stress should be vertical and equal to the pressure of the overburden; the fractures should be horizontal with injection pressures equal to or greater than the pressure of the overburden. Horizontal fractures cannot be produced by hydraulic pressures less than the total pressure of the overburden. These conclusions are compatible with field experience in fracturing and with the results of laboratory experimentation. INTRODUCTION The hydraulic-fracturing technique of well stimulation is one of the major developments in petroleum engineering of the last decade. The technique was introduced to the petroleum industry in a paper by J. B. Clark,' of the Stanolind Oil and Gas Co. in 1948, and since then its use has progressively expanded so that by the end of 1955 more than 100,000 individual treatments had been performed. The technique itself is mechanically related to three other phenomena concerning which ah extensive literature had previously developed. These are: (1) pressure parting in water injection wells in secondary-recovery operations, (2) lost circulation during drilling, and (3) the breakdown of formations during squeeze-cementing operations, all of which appear to involve the formation of open fractures by pressure applied in a wellbore. The most popular interpretation of this mechanism has been that the pressure had parted the formation along a bedding plane and lifted the overburden, notwithstanding the fact that in the great majority of cases where pressures were known they were significantly less than those due to the total weight of the overburden as determined from its density. Prior to 1948, this prevalent opinion had already been queried by Dickey and Andresen,2 in a study of pressure parting; and by Walker,"' who, in studies of squeeze cementing, pointed out that the pressures required were mostly less than those of the overburden, and inferred that the fractures should be vertical. J. B. Clark,' in his paper introducing hydraulic fracturing, and later Howard and Fast," and Scott, Bearden, and Howard," also of Stanolind, postulated that the entire weight of the overburden need not be lifted in producing horizontal fractures, but that it was only necessary to- lift an "effective overburden," requiring a correspondingly lower pressure. Hubbert,7 in discussing the paper by Scott and associates, pointed out that the normal state of stress underground is one of unequal principal stresses; and in tectonically relaxed areas, characterized by normal faults, the least stress should be horizontal. Therefore, in most cases, fracturing should be possible with pressure less than that of the overburden and, moreover, such fractures should be vertical. Harrison, Kieschnick, and McGuire,8 also on the expectation that the least principal stress should be horizontal, argued strongly in favor of vertical fracturing. Scott, Bearden, and Howard6 observed that, when

Jan 1, 1958

By Milton H. Fies

EARLY in 1945 the laboratories of the Southern Research Institute will begin active research investigations on behalf of industrial clients. This achievement has come after four years of planning by a group of Alabama businessmen, and is in partialanswer to an urgent need in the South. Those who conceived the Institute have long realized that a marked relationship exists between scientific research and the economic well-being of the several regions of the country. Clearly, technological research, generally absent in the South, is the medium through which are created new finished goods industries, and the increase of technological research is perhaps the most important long-range project in the South.

Jan 1, 1945

By Frank Firmstone

The material described below was made at Furnace No. 2, Longdale, Va., Oct. 28, 1907, during a sudden derangement of working, in the course of which the furnace became entirely bridged over and for some time no solid material whatever descended into the hearth. This caused the hearth to become so completely emptied that, at the tuyere-level, a pricker put in at one tuyere could be seen by looking in at the opposite one. The tap-hole was opened and the iron got out with some difficulty. It ran sluggishly, throwing many sparks, but was not too thick to run into the chill-molds. Naturally, the product was assumed to be white iron, which is almost always produced under similar circumstances; but on removal front the molds it proved to be very strong and tough, although full of blow-holes. Most of these blow-holes bad bright, unoxidized walls. The iron could be drilled by using a "special steel" drill, the drillings curling up similarly to those of steel. An analysis by P. W. Shimer of this unusual product gave: Si, 0.019; P, 0.228; S, 0,39; Mn, 0.042; C, 2.366; and graphite, 0:000 per cent. A cast of iron made just before the disturbance contained P, 0.98, and Mn, 1 per cent. The peculiar product seems to have been decarburized in the hearth and, at the same time, to have lost much phosphorus and manganese, either by the action of the blast in the empty hearth, or, more probably, by. contact with the cinder rich in iron which was formed at the time. Unfortunately, no specimen of the cinder was preserved, so its composition cannot be given. It seems very remarkable that, with the furnace in bad condition, the temperature should be high enough to keep such

Sep 1, 1908

By O. J. Hassel, W. T. Maidens, J. H. Calbeck

The rotary gas fired reheating furnace used by the American Zinc Oxide Co. at Columbus, Ohio for Therotarygasfiredreheatingfurnacerefining lead-free zinc oxide is described. The outstanding features of this operation are that the color of the zinc oxide is greatly improved, sulphur is eliminated, and cadmium arethatrecovered without densifying the product to an objectionable degree. IN 1919 Leland S. Wemple obtained a patent for a process of reheating zinc oxide wherein the "coarsening of grain due to excessive heating was avoided." He taught in his specification that if solid carbonaceous material, such as lamp black, was added to the zinc oxide in proper amounts prior to reheating, objectionable sulphur compounds could be removed and the color would accordingly be improved and no objectionable densification would occur because of the relatively low temperature required. The situation that made this invention imperative was the newly opened zinc oxide plant of the American Zinc, Lead & Smelting Co. in Hills-boro, Ill. This was one of the early Western Type American Process zinc oxide operations. Characteristic of all of these early Western operations using Tri-State and Western ores was the great difficulty encountered in obtaining a product low enough in sulphur to compete with the Eastern Type American Process zinc oxides which were made from ores containing very low sulphur percentages. Wemple demonstrated that the refining process of his invention produced a superior color and although this was true and a most welcome feature, the primary purpose of the early refining operations at Hillsboro was to reduce substantially the high sulphur content of the crude zinc oxide. Although many and varied attempts had been made for refining zinc oxide none of the processes had a commercial history of any consequence until Wemple's invention became standard practice for the American Zinc, Lead & Smelting Co. in 1919 and their operations have been unique in that substantially all of their lead-free zinc oxide has been reheated since the first installation at Hillsboro. This process has become known in the industry as refining. The furnace developed by Wemple and continued in use by the company from 1919 until 1943 was unusual and merits some consideration by way of review in this paper. The furnace was essentially a double hearth coal-fired muffle furnace with a mechanical raking system consisting of a central shaft supporting six rabble arms in each muffle. The untreated or "crude" zinc oxide was fed onto the outer rim of the top muffle, moved to the center where it dropped to the lower muffle and progressed to the outer rim where it was discharged into an alloy screw conveyor. The retention in this furnace was extremely short, about 5 min, and the shallow zinc oxide bed on the hearths of the muffles was being continuously turned by the fast moving rabbles. Soft coal was burned on the grates below the lower muffle and the long yellow flame necessary to carry the heat around both muffles resulted in a very inefficient combustion of the fuel. The temperature of the top of the lower muffle seldom exceeded 65 °C although the oxide itself often reached 700°C before discharge. The capacity of this furnace was approximately 1/2 ton per hr. In our plant at Columbus it was necessary to keep four of these furnaces running in parallel to take care of the production because, as mentioned above, every pound of zinc oxide produced during these 24 yr passed through one of these refining furnaces. An essential part of this refining operation was the use of carbonaceous material admixed with the zinc oxide fed to the furnaces. Between 1 and 2 pct of a bran produced in the processing of cotton seed was added to all zinc oxide charged to the furnaces. The bran ignited on the top hearth and was still burning when the charge fell from the top hearth to the bottom hearth making a cascade of sparks. The rapid turning of the zinc oxide caused these particles of bran to flash on the hearths behind each rabble; but the combustion, of necessity, had to be complete by the time the charge reached the outer rim of the bottom hearth, otherwise the finished product would be contaminated with the charred particles of bran which would give the zinc oxide an unsatisfactory color. Although this operation was initiated to reduce objectionable sulphur percentages, as time went on new properties of the product were appreciated which made advisable continuing the refining process long after other methods of sulphur reduction became known in the industry. The particle size and particle size distribution, the absence of colloidal fines and perhaps a unique surface condition gave this product an outstanding performance when used in paints. The Wemple furnaces installed in Columbus in 1919 had to be rebuilt frequently and were extravagant in the use of fuel. The raking mechanism and the muffles required excessive maintenance expense and as the furnaces wore out the problem arose whether to continue along this line or to explore the possibilities of obtaining similar or better results in the simpler and more commonly used rotary furnace. To this end special research was initiated in 1941 on a small laboratory rotary

Jan 1, 1951

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance' present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By Francis Cameron

Mining is both exciting and rewarding-although at times somewhat frustrating-and we all can have real pride in our industry, in its people, and in its accomplishments. It is, however, with concern that I have noted a deterioration in this Country in what might be called mining's stature and in the growth of a belief in many quarters that our mineral reserves are rapidly approaching exhaustion. In other words, there is a popular image that we are fast becoming a "have not" nation in many respects and that the domestic mining industry can no longer be considered, in the vernacular of Wall Street, to offer much in the way of "growth potential." I do not subscribe to this hypothesis, nor do I believe that the record of the mining industry bears this out. However, let me add that we can, in time, talk ourselves into this frame of mind and we can hasten the day when this very well might come about by unnecessary and unwise legislation or regulation. My remarks today are basically designed to give my reasons for refuting this negative philosophy and to review our record. With your help, I know we can improve our image, and the public's recognition of our industry's peculiar problems.

Jan 4, 1968

By Hermann Wedding

I ASK your permission to speak about a matter which is not of a specifically scientific nature, but more of a general-I might even say of an international-nature, and the international character which this city now presents must be my justification for introducing it. The Germans, very often, are thought to be an exceedingly warlike people, but I come to-day in the capacity of a peacemaker. Our German language is an original language; it is, therefore, a language in which it is impossible to change the meaning of a word at will. It may be, perhaps, easier in a combined language, as the English, to associate and to exchange meanings. Now, a word which we hear a great deal at the present day, is "Stahl," in English, "steel." This word means, in the German language, a substance which can be hardened. As the German literature, in relation to metallurgy, is the oldest of the modern world, this circumstance may give the German a right to ask for consideration. But I think, now, when the four languages, German, Swedish, French, and English, compete in rich metallurgical literature, it is very necessary to have uniformity in the nomenclature of iron, which would prove not only useful for science, but equally so for trade. For that purpose I propose to make the divisions of iron so that the word steel shall comprise a subdivision and not a primary division as formerly. Nature furnishes us iron mostly in the state of oxides, and if in any other condition, we must convert the ore into oxide before we can make iron. The oxides are always mixed with certain earthy substances called rock or gangue. The extraction of iron involves, therefore, the twofold process of the reduction of the iron, and im¬parting to it the amount of carbon necessary for technical purposes, and the separation of the reduced and carburized iron from the gangue. The reduction is always effected by carbon or carbonaceous substances (coke, anthracite, carbonic oxide, etc.), and the result is, according to the degree of heat employed, either malleable iron or a non-malleable iron. The process of making malleable iron in this way is called, generally, the direct process-in German, Rennarbeil. It produces the iron in a solid state with a fluid cinder. By this process our ancestors made all their iron, and it has been revived in various ways in modern times up to the process of Mr. Blair, so far as I know, always without commercial success. The

Jan 1, 1877

By Hermann Wedding

I ask your permission to speak about a matter which is not of a specifically scientific nature, but more of a general—I might even say of an international—nature, and the international character which this city now presents must be my justification for introducing it. The Germans, very often, are thought to be an exceedingly warlike people, but I come to-day in the capacity of a peacemaker. Our German language is an original language; it is, therefore, a language in which it is impossible to change the meaning of a word at will. It may be, perhaps, easier in a combined language, as the English, to associate and to exchange meanings. Now, a word which we hear a great deal at the present day, is "Stahl," in English, "steel." This word means, in the German language, a substance which can be hardened. As the German literature, in relation to metallurgy, is the oldest of the modern world, this circumstance may give the German a right to ask for consideration. But I think, now, when the four languages, German, Swedish, French, and English, compete in rich metallurgical literature, it is very necessary to have uniformity in the nomenclature of iron, which would prove not only useful for science, but equally so for trade. For that purpose I propose to make the divisions of iron so that the word steel shall comprise a subdivision and not a primary division as formerly. Nature furnishes us iron mostly in the state of oxides, and if in any other condition, we must convert the ore into oxide before we can make iron. The oxides are always mixed with certain earthy substances called rock or gangue. The extraction of iron involves, therefore, the twofold process of the reduction of the iron, and imparting to it the amount of carbon necessary for technical purposes, and the separation of the reduced and carburized iron from the gangue. The reduction is always effected by carbon or carbonaceous substances (coke, anthracite, carbonic oxide, etc.), and the result is, according to the degree of heat employed, either malleable iron or a non-malleable iron. The process of malting malleable iron in this way is called, generally, the direct process—in German, Rennarbeit. It produces the iron in a solid state with a fluid cinder. By this process our ancestors made all their iron, and it has been revived in various ways in modern times up to the process of Mr. Blair, so far as I know, always without commercial success. The

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.' These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties'3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969

By T. O. Massalski, J. D. Ayers

A massive transformation, 0 —am, takes place in a number of copper-based systems where the ß phase field at high temperatures extends to compositions that are slightly less solute-rich than the limits of the a phase field that exists at lower temperatures. Consequently a solid-state transformation becomes possible that does not involve a change of composition. Within this narrow range of composition the massive am phase can be usually produced in two ways: by a fast quench from the ß phase through the a phase field, or by pulse heating into the a phase field of an undecomposed ß phase retained at room temperature by a prior quench. In the Cu-Ga system the occurrence of a massive am phase has been also observed in alloys whose composition falls outside the equilibrium a phase field1 but not in the Cu-Zn system.2 We have recently observed the occurrence of the ß — am transformation also in two silver-based systems, Ag-Zn and Ag-Cd. The a and 0 phase fields in these systems again slightly "overlap" in a narrow composition range. In the Ag-Zn system this range falls between 36.7 and 40.2 at. pct Zn, and in the Ag-Cd system between approximately 41 and 42.5 at. pct Cd. Alloys were prepared from high-purity materials and cast in quartz tubes under inert atmosphere. No significant change of composition occurred during casting. After homogenizing in the 0 phase field, small pieces of each alloy were reheated at the homogenizing temperatures for a few minutes and quenched into various media. There were examined metallographic-ally after removal of surface layers that may have suffered from contamination or from the loss of the solute element. In the Ag-Zn system extensive areas of the am phase (identified by selective etching, observation of the slip trace variants, and occurrence of twinning) were observed in a comparatively low-zinc alloy (37.8 at. pct Zn) for all quenching media employed: iced

Jan 1, 1969