Search Documents

By Walter C. Lawson

THE primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in' the Morenci open pit. GENERAL MINING OPERATIONS Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste, is loaded., into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high:. They are blasted- with churn drill holes, and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). PREPARATION OF PANEL GRADE In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many ties broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1947

By Tony B. Szwilski, K. Unrug

INTRODUCTION Since the introduction of longwall coal mining systems, reliable predictions of roof support requirements at the face and the roof caveability in the gob area have been major contributors to the success of the longwall face by means of safety and face productivity. That is, the successful operation of a longwall is well-served by good regular caving of the gob. In recent times, with the advent of increased coal face mechanization and capital investment, the evaluation of the feasibility of longwall mining has become essential. In the United States, where a face unit for a face length of about 150 metres may cost around $6 million, a quantitative system that would assist in selecting the best equipment for the coal would prove extremely beneficial. There have been many such varied investigations in the past few years. A vast -amount of work has been invested principally by West Germany [3, 7, 8, 91 , Poland [I, 101 , United Kingdom [4, 5, lo], France [4], and South Africa [4]. It is the object of this paper to review this previous research work and give an outline that may be used as guidelines for long- wall evaluation. Essentially, for the initial design phase for a longwall system, account must be taken of the geometry of the coal panel, its position relative to the surface (depth), direction of the coal cleat system, faults and in-situ stresses and other neighboring workings in the same coal seam and other seams both above and below. The advance of the coal panel disturbs the stress field and in doing so creates an abutment zone around the face. At this stage the condition of homogeneity of the surrounding rock mass does not apply. The magnitude of the rock strata pressure may exceed the ultimate strength of the rocks and create zones of clastic, plastic and elastic material, the limits of which are difficult to determine. The collapse of the gob and resulting expansion of the displaced waste roof rock, create a statically undefined support complicating an already unclear rock structure. For example, it is often a point of debate whether, indeed, the vertical strata pressure develops to regain the original magnitude of virgin stress. Under these post-failure circumstances an analytical approach based on simplified and idealized assumptions can only be considered a very general approximation. Theoretical concepts, however, may be adequately supplemented by empirical methods that are based on numerous underground observations and surveys [3, 4, 7, 8]. These methods employ the use of rock indices that very handily correspond to the competence of the roof rock mass. Scale model work [3, 41 , using equivalent materials representing the surrounding rock mass within the coal seam zone, have given valuable qualitative and sometimes quantitative data in addressing the behaviour of the rock mass around longwall panels. To characterize the state of art of caveability predictioqthe principal concepts will be reviewed with special emphasis placed on practicality for the planning of longwall operation. It has been the general observation of the authors that many of the literature surveys published in English often neglect reference to other international mining literature. It is with this point in mind that an overall review has been written including mining concepts identified with the principal coal mining countries. THEORETICAL CONCEPTS Arching Theory For the development of this theory, assumption has been made that an extracted height, h, in a coal seam results in an extracted panel of width, w . Also, the coal seam is horizontal and the rock strata of both the roof and floor are homogeneous. The primary (virgin) stress distribution will change in the roof as well as the floor. As a result of lack of support caused by the excavation (in the gob area) an additional load is developed due to the redistribution of the load around the sides of the panel, referred to as the abutment, R, where: [ ]

Jan 1, 1982

By N. M. Levine

WHETHER the United States and its allies can W meet the challenge of a war brought by the Communists will depend largely on who wins the battle of steel production. At the present stage of the world situation, the United States and the other members of the Western family of nations have the lead on iron curtain countries. But we have no sure way of knowing what is happening at Magnetogorsk and other Russian iron and steel producing centers. We must also face the possibility that we may have to meet the challenge alone. The fortunes of war and world politics can strip us of friends and co-fighters quickly. The destruction of Hiroshima and Nagasaki are indicative of what the world can expect if war-madness ever grasps the earth again. Our domestic supply of high grade open-pit and underground iron ore is dwindling because of the drain of three wars and higher than ever civilian consumption. The production of iron ore and its eventual use in blast furnaces are the critical problems of an armed democracy today. The world crisis has led to efforts towards beneficiation for increasing ore supplies. The huge reserves represented by the magnetic taconites at the eastern end of the Mesabi, once in production, should provide us with a substantial portion of our native ore for many years. The estimated 10 to 20 million tons of concentrates annually can be increased in an emergency. If we had a certainty of peace for the next 50 to 100 years, the situation would be a stable, hopeful one, aided by importations of high grade ore from sources such as Canada and Venezuela. The hard truth is that we have little surety of peace tomorrow morning. Let us assume 'the U. S. could build sufficient processing plants for increasing production of magnetic taconites under the pressure of national emergency. We must also recognize the power of atomic warfare to contaminate an area as large as the Eastern Mesabi. Thus, it becomes imperative to seek some means of protecting our ability to produce the steel we may one day need to survive. The nonmagnetic taconites, completely dwarfing the magnetic taconites areawise as well as tonnage-wise, might provide us with this insurance. Present indications are that they will be considerably more expensive to treat, but in a desperate situation we might be very grateful for ores yielding 40 to 50 pct Fe recoveries at grades of 53 to 58 pct Fe carrying low phosphorus. The University of Wisconsin, because of the difficult iron ore situation in the state, has been working on the nonmagnetic taconite problem for the past three years in the hope of making a contribution toward its eventual solution. In Wisconsin, the Western Gogebic Range has been the state's most effective iron producing area. Today however, only two mines are in operation, both underground and approaching depths of more than 3000 ft. The range, however, does have a large supply of nonmagnetic taconites and presents a promising field for study. While the Gogebic offers one large source of nonmagnetic taconites, Michigan and Minnesota have even greater supplies of such material. Alabama, the northeastern states and the West all have low grade iron ore sources which might be utilized under extreme conditions. The Gogebic Range located in northeastern Wisconsin and northwestern Michigan has a total length of about 70 miles, about 45 of which are in Wisconsin. The iron formation averages 500 to 600 ft in width, dips 70' to the north and strikes at approximately N 63° E. The formation is sedimentary and consists of six distinct members characterized by alternating divisions of ferruginous chert and ferruginous slate. The footwall is generally quartzitic and the hanging wall of a sideritic slatey character. The iron minerals are mainly hematites with some magnetites, goethites, limonites and small amounts of siderite. In the area studied, very small amounts of iron silicates were observed. The magnetites occurred mostly in the Anvil-Pabst and Pence members, mixed with hematites and representing roughly about 10 to 20 pct of the total iron in the formation, thereby characterizing it as nonmagnetic. The gangue is of various forms of silica such as chert, opal and flint. Complete liberation of iron and gangue minerals is rare. There is always some iron present in the chert ranging from jasper-like solutions to fairly coarse iron oxide specks. Likewise, one always finds finely dispersed silica within the iron minerals. In late 1943 the Bureau of Mines carried out a trenching and sampling program in the two mile stretch between Iron Belt and Pence in Iron County, Wis. Preliminary work was based on samples from one of the four trenches cut by the Bureau of Mines. More detailed work following the preliminary analysis was then undertaken on samples composited from all the trenches, thereby giving a wider and more representative coverage of the area. A study of the

Jan 1, 1952

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By R. A. Wolfe, H. W. Paxton

Self-diffilsion coefficients for cr51 and Fe55 in 12 pct Cr-Fe and 17 pct Cr-Fe for Fe55 in chromium, and for Cr51 in vanadium have been measured. The results are compared with other values for the Fe-Cr system, and with the various theories of diffusion in hcc metals. Some empirical correlations are discussed between Do and Q in hcc systems, or, expressed differently, the constancy of ?G*/T solidus for seveval bcc metals and alloys is noted. It appears very probable that a vacancy mechanism is operative in bcc metals, hut this cannot he stated with certainty. THE great bulk of work on diffusion in metals, both experimental and theoretical, was for many years concentrated on those with close-packed and, in particular, fcc lattices.1,2 There appears to be little doubt that the mechanism of diffusion in these solids is vacancy migration, leading to mass transfer and in substitutional solid solutions to a Kirken-dall effect.3,4 For bcc metals, the picture is much less clear. The Kirkendall effect certainly occurs in several alloys.5-10 However, attempts to understand the factors contributing to the pre-exponential in the usual expression for the diffusion coefficient D =D, exp {-Q/RT) by extension of ideas useful in close-packed lattices have not always been successful. Zener,11 Leclaire,12 and Pound, Paxton, and Bitlerl3 have suggested that various forms of ring diffusion may be important in some bcc metals. For close-packed metals, Do is usually about 1 sq cm per sec and Q - 35Tm kcal per mole (Tm = melting temperature in OK). The theory of Pound et al. suggests for ring diffusion that Do may be about 10-4 and Q, although difficult to calculate with any precision, would be significantly less than 35 T,. The experimental results on self and solute diffusion in ? uranium14,15 and ß zirconium,10 and for solutes in 0 titanium,17 and possibly for self-diffu- sion in chromium below about 0.75 T,," gave some credence to this theory. However, not all bcc materials display low values of DO and Q, and the exceptions were not predicted by any theory. Furthermore, it has recently become apparent that, in bcc materials, log D is not always linear with T-l if a sufficiently wide range of temperature is studied.16,18 This variation may be such that Q may increase18,19 or decrease20 with increasing temperature. The present work was undertaken in an attempt to provide further diffusion data on bcc metals, and to try to understand the factors which contribute to differences in behavior between the various elements. For part of this work, the Fe-Cr system was chosen since it is of considerable technological importance, and data on 12 pct Cr and 17 pct Cr alloys appeared well worthwhile to supplement that existing for the remainder of the stern.18,22 The diffusion of Fe55 in chromium was studied as an example of a more or less "normal" tracer element in a possibly abnormal host lattice. Finally, no data were available for vanadium, the neighbor of chromium in the periodic table, because of lack of a suitable isotope so cr55 was used as a tracer in a few preliminary experiments. For convenience, we shall refer to elements whose Do and Q are low compared to those predicted by Zener's theory as "anomalous". PROCEDURE This investigation determined self-diffusion rates by means of radioactive tracers and the integral-activity method first utilized by Gruzin.23 In this method a thin layer of radioisotope of the diffusing element is plated or coated onto a planar surface of the diffusion sample, which is then given an isothermal-diffusion annealing treatment. The determination of an activity-penetration curve involves measuring the residual activity of the specimen after each successive layer or section has been removed parallel to the original planar surface. The method used here is essentially the same as that used by Gondolf18 and Kunitake.21 Two radioactive tracers, cr51 and Fe55, were used in this investigation. Diffusion coefficients were determined for the diffusion of one or both of these tracers in four different materials, viz., Fe-12 wt pct Cr alloy, Fe-17 wt pct Cr alloy, chromium, and vanadium. The diffusion samples had nominal dimensions of 1.5 cm diameter and 0.5 cm thickness. The grain size was several millimeters for the Fe-Cr alloys and at least 1 mm for the chromium and vanadium samples. Accurately planar surfaces

Jan 1, 1964

No. 264. A long established company operating steel and iron foundries, machine and forge shops, whose varied products are sold to the Government, railroads, mining and contracting industries, etc., has, openings in both manufacturing and selling departments for men with technical education and experience who are not subject to military call. State full particulars, kind of position preferred and salary expected. No. 265. Young man wanted, technical graduate preferred, to superintend construction f a small charcoal blast furnace. Man with blast-furnace experience preferred. For the right kind of man this is, not only a permanent job but an opportunity. In writing, give full particulars as to age, education, experience, salary wanted, etc. No. 26.6. An important copper mining and smelting company in Arizona needs two or three metallurgical chemists, at salaries. ranging front $150 to $175 per month. No. 267. A consulting mining engineer needs two superintendents for developing chrome deposits near Philadelphia; and another technical man for other engineering work in the same vicinity. No. 268. An iron-mining company, in New York State needs a mining engineer with knowledge of geology and acquaintance with construction work; A married man, with about 10 years' engineering experience preferred.

Jan 2, 1918

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By Vernon A. Mrak

The Powder River Basin of northeast Wyoming was the first area in the state to receive attention during the early days of uranium exploration. Although the uranium occurrences are many and widespread, most of the known ore deposits are quite small and difficult to mine. As a result of this, detailed regional exploration in the Powder River Basin has been neglected. The uranium ore deposits occur in that part of the Wasatch Formation that is of earliest Eocene age, and they are scattered over an area of about 400 square miles. All uranium ore deposits are associated with red beds or altered sandstones within the Wasatch Formation. Uranium ore was first shipped from the region in 1953. Total production through June of 1965 is 506,257 tons of uranium ore containing 1,922,527 pounds of U3O8. The average grade of ore is about 0.19 per cent U3O8. The major producing area of the Powder River Basin is the Monument Hill district where about 91 per cent of the basin's total uranium ore has been mined. The source of uranium is presumed to have been the Oligocene, Miocene, and perhaps Pliocene tuffaceous rocks that once overlay the area. Joints, fractures, and permeable beds or zones were the passageways for the migration of uraniferous waters from the overlying beds to the Eocene host rocks.

Jan 1, 1968

By Koehler S. Stout

At today's mineral prices, unproductive or low productive work in any underground mine must be kept at a minimum to insure a profit. Improper level and raise spacing can be one of the contributing factors to high production costs, and little can be done to reduce these costs after the spacing interval has been chosen. The objective in selecting level spacing is to find the most desirable interval which produces ore at the least cost per ton while still operating within the highest margins of safety and efficiency to the workmen. In addition, maximum possible recovery of ore under the conditions must be attained.

Jan 11, 1962

By M. E. Wadsworth, K. C. Bowles, H. E. Flanders, R. M. Nadkarni, C. E. Jelden

The kinetics of precipitation of copper on iron of various purity were carried out under controlled conditions. The rate of reduction has been correlated with such parameters as copper and hydrogen ion concentration, geometric factors, flow rate, and temperature. The character of the precipitated copper as a function of flow conditions and rate of PreciPitation has been observed under a variety of conditions. ThE precipitation of copper in solution by cementation on a more electropositive metal has been known for many years. Basile valentine' who wrote Currus Triumphalis Antimonii about 1500, refers to this method for extraction of copper. Paracelsus the Great2 who was born about 1493 cites the use of iron to prepare Venus (copper) by the "rustics of Hungary" in the "Book Concerning the Tincture of the Philosophers". Agricola3 in his work on minerals (1546) tells of a peculiar water which is drawn from a shaft near Schmölnitz in Hungary, that erodes iron and turns it into copper. In 1670, a concession is recorded4 as having been granted for the recovery of copper from the mine waters at Rio Tinto in Spain, presumably by precipitation with iron. Much has been published in recent literature on the recovery of copper by cementation, the majority of the articles being on plant practice.5-24 The rest include articles on investigation of the variables involved25-28 and a review of hydrometallurgical copper extraction methods." This literature has established: a) The three principal reactions in the cementation of copper are Cu + Fe — Fe+4 +Cu [ 11 One pound of copper is precipitated by 0.88 lb of iron stoichiometrically. In actual practice about 1.5 to 2.5 lb of iron are consumed. 2Fe+3 + Fe — 3Fe+2 [21 Fe +2H'-Fe+2 + H2 [3] Reactions [2] and [3] are responsible for the consumption of excess iron. Wartman and Roberson'28 have established that Reactions [ I] and [2] are concurrent and much faster than Reaction [3]. b) Acidity control is important in the control of hydrolysis and the excessive consumption of iron. he commercial workable range is approximately from pH = 1.8 to 3." c) Iron consumption is closely related to the amount of ferric iron in solution. Jacobi" reports that, by leaving the pregnant mine waters in contact wi th lump pyrrhotite (Fe7S8) for 3 hr, all the iron was reduced to the bivalent condition and scrap iron consumption was cut to 1.25 lb scrap per pound of copper precipitated. He also reported that SO2 has been used successfully to reduce ferric iron to the ferrous state. d) The ideal precipitant is one that offers a large exposed area and is relatively free of rust. e) High velocities and agitation show a beneficial effect upon the rate of precipitation, as it tends to displace the layer of barren solution adjacent to the iron and also dislodges hydrogen bubbles and precipitated copper to expose new surfaces. Little work, however, has been published on the reaction kinetics of copper precipitation on iron. Cent-nerszwer and Heller20 investigated the precipitation of metallic cations in solutions on zinc plates. They found the cementation reaction to be a first-order reaction. The rate constant was independent of stirring for high stirring rates and they concluded that the rate is governed by a diffusional process at low stirring speeds and by a "chemical" process at higher stirring speeds where the rate reaches a constant value. This conclusion has been challenged by King and Burger30 who could not find any region where the rate was independent of the stirring speed, although the rate constant they had obtained for high stirring speed was greater than the maximum value of the rate constant reported by Centnerszwer and Heller (by a factor of six). King and Burger, therefore, concluded that the rate of displacement of copper was controlled only by diffusion. Cementation of various cations on zinc has been summarized by Engfelder.31 APPARATUS A three-necked distillation flask of 2 000-mm capacity was used as a reaction vessel. A pipet of 10-mm capacity was introduced through one of- the side necks, the sample of sheet iron, mounted in a rigid sample holder, through the other, the stirrer being in the middle as shown in Fig. 1. The whole assembly was immersed in a constant-temperature bath. The stirrer was always placed at the same depth in the solution. EXPERIMENTAL PROCEDURE Reagent-grade cupric sulfate (J. T. Baker Chemical Co., N.J.) was used to make up a stock solution containing 10 g of copper per liter which was then diluted to various concentrations as required. Experimental data were obtained by measuring the amount of copper and iron ions in solution at successive time intervals. The initial volume of the solution was always 2000 ml, 10-ml aliquots being removed each time for chemical analysis. Because the total volume change of the solution was less than 10 pct, no correction was used for solution volume change. Nitrogen was bubbled through the solution before and

Jan 1, 1968

By F. Louis Grammer

THE difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace gas is richer in CO, and poorer in hydrocarbons and hydrogen, as is shown in Table I. TABLE I.-Volume-Composition of Producer-Gas and Blast-Furnace Gas.. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO . 22 to 33 25.5 00., . 6 to 3 13.0 H . . 13 to 7 1.5 CH, 3 to 1.5 0.0 N . 54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydro-carbons and, hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur-namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the products which are specially high in sulphur-content. An advantage would be gained if coal was coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Sep 1, 1908

By G. D. Cody, D. S. Beers, B. Abeles

The thermal diffusivity (thermal conductivity divided by specific heat) of Armco iron has been measured over the temperature range 30º to 1025ºC. The results are in good agreement with the thermal diffusivity computed from published values of thermal conductivity and specific heat, except near the Curie point and at the a to y phase transition, where the measured diffusivity undergoes rabid variations. The differences observed are ascribed to a rapid variation in the electronic thermal conductivity near the Curie point, and a decrease in the lattice thermal conductivity, at the a to ? phase transition. A major difficulty in measuring the thermal conductivity of materials at high temperatures is the determination and elimination of radiation losses. It has been shown, however, that in measuring thermal diffusivity D (thermal conductivity/specific heat) radiation losses can be taken into account exactly.' In order to test the performance of a newly designed apparatus for measuring thermal diffusivity of solids,' we measured Armco iron to an accuracy of 2 pct in the temperature range 30" to 1025°C. This material was selected since both the thermal conductivity,3'4 k, and specific heat,5 C, are known accurately in this temperature range and thus the measured values of D could be compared with D computed from the pub-

Jan 1, 1962

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

By EL HANAF

The exploratory program initiated in Egypt in 1937 by four major oil companies was well under way early in 1939. Extensive gravity-meter surveys were carried out in the Sinai Peninsula and the Eastern and Western Deserts. Seismic and magnetometer work vas conducted on a restricted scale. The data collected justified wildcat drilling on structures located geophysically and/or geologically.

Jan 1, 1946

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By H. B. Huntington

Some of the basic problems in understanding elec-tromigration in metals are discussed, along with the attempts that are being made to handle them. One such problem is the effect of the electrostatic forces. It is now acknowledged that the momentum exchange with charge carriers plays generally a dominant role in the driving force but the question remains to what extent the electrostatic force may still be effective. The electromigration of interstitial impurities is also an area which presents some intriguing questions. For the substitutional impurity, moving by the vacancy mechanism under the influence of an electric field, the correlation considerations are somewhat more complex than have been previously recognized. Another problem of basic importance in the calculution from first principles is the strength of the "electron friction" force, say for a simple one-band metal. A related problem growing out of the preceding is the prediction of the direction of the "electron wind" force for metals with band structure involving both holes and electrons. THE term electromigration has come to be used to describe the flow of matter in condensed phases carrying high electronic currents such as metals and alloys, whereas one usually reserves the term electrolysis for situations where the current is largely ionic, particularly in the liquid state such as molten salts. It follows that the mass transport number in electromigration is always very small, of the order of 10-7. Studies of electromigration date back some 30 years but the modern period would appear to date from the work of Seith and Wever1 who in the mid 1950's first incorporated markers to display mass motion relative to the lattice and first suggested that the direction of the mass flow was primarily determined by the sign of the charge carriers. Since that time interest in the field has grown steadily and more rapidly recently as certain technological applications became apparent. Chief of these is certainly the deleterious effects that electromigration can cause, even at relatively low temperature, to current-carrying elements in integrated circuitry.2 These phenomena have been the subject of intense study and considerable ingenuity. On the constructive side electromigration has proved a useful tool in the purification of certain metals.3 The interest of this paper is, however, centered more on the basic aspects of the subject than on its technological applications. That high electric currents should give rise to mass flow in metals and that the driving force should be more directly associated with momentum exchange with the charge carriers than with the electrostatic field are ideas that no longer cause surprise or particular interest. The field has matured to the point where the general concepts are widely accepted and continued progress in basic understanding rests on more detailed and quantitative exploration. It is the purpose of this paper to point out what are some of the current problems. As a result, we expect to raise more questions than we answer. The first of these will be the role of electrostatic forces, if any, in electromigration. A second section will deal with the electromigration of interstitials. A third and final section treats with electromigration of substitutional impurities or of the matrix atoms themselves. ELECTROSTATIC DRIVING FORCE In the conceptual treatments of electromigration it has been customary to write the driving force in terms of an effective charge number Z* and to divide it into two terms F = e£Z* = e£[Zel- z(pd/Nd)(N/p)(m*\m*\)] [1] The first of these represents the electrostatic force under immediate consideration in this section and the second and usually dominating term for metals arises from momentum exchange with charge carriers, commonly called the "electron drag" term. As can be seen it is set proportional to the electrons per atom, z, and the ratio of the specific resistivity of the moving entity to the corresponding resistivity per matrix atom. The (m*/Im*I) factor takes into account the fact that the sign of the charge carrier determines the sign of the driving force. The specific resistivity of the moving entity is averaged over its path. In the case of motion of the matrix atoms by vacancies this gives rise to approximately one-half the resistivity at the saddle point since the scattering power of the atom at its equilibrium position bordering the vacancy differs only slightly from that of a normal matrix atom. Although the formulation of the "electron drag" term in Eq. [I] is based on a highly simplified model for electron defect scattering, the essential features implicit in the expression are common to all the theoretical approaches that have so far appeared in the literature.4-6 As for Zel, most treatments of electromigration have included the quantity as the parameter which measures the direct interaction of the electrostatic field with the ion and equated it to the nominal valence of the latter. However, there has been considerable discussion whether this interaction may not be 0 in many cases.6 If the moving ion is always enveloped by the same distribution of shielding charge, then clearly its motion will not involve any work done by the electric field and one can expect there will be no electrostatic force exerted on such a neutral composite. From this point of view the shielding charge around the ion would be said to be complete and hence the entity within the Debye shielding sphere would be unaffected by the electrostatic field per se. There is, however, the prospect that, as the moving ion progresses, new charge comes in to participate in the shielding action

Jan 1, 1970

By V. J. Sikora, T. S. Hutchinson

This paper presents a method for making a water-rlrive ana1gsis without prior knowledge of aquifer geometry and uniformity using a standard desk calculator. Although it is necessary to know the initial oil in place to use this method, this is a minor limitation to the scope of (he method since in most reservoirs it is possible to obtain reasonably accurate volumetric oil-in-place estimates. An equation is developed which relates pressure at the water-oil contact to the water influx rate as a function of time by a factor called the resistance function. The resistance function introduces the composite effect of the aquifer geometry and flow resistance disrribution. It is pointed out that the characteristic shape of this function makes it possible to start with on approximation of the function and successively improve the approximation until the correct resistance function curve is obtained. In this fashion water-drive estimates can be made without the limitation of assuming simplifed aquifer shapes and flow distributions. This is the novel feature of this development. Methods are given for extrapolating the final curve to calculate future aquifer behavior. Equations are developed for adjusting the pressures and water influx rates where it appears that possible errors in these quantities make it difficult or impossible to obtain a useuble resistance function curve without this adjustment. Application of the pressure build-up analysis techiiique to estimate. some of the aquifer properties is also presented INTRODUCTION A great many oil pools are the result of oil accumulation in some type of trap in an otherwise large and continuous porous stratum. The void space of this stratum outside of the oil pool itself is filled with water or brine. In analyzing performance of the oil pool surrounded by this water aquifer, it is quite necessary. in most cases, to include behavior of the water. When the pressure at any point in a fluid system is lowered, such as by opening a well in an oil sand, fluids in the immediate neighborhood of this point will begin flowing towards this lower pressure sink. As pressure in this area drops due to flow towards the sink, fluids from farther out will start to flow towards the lower pressure. As more and more fluid is removed from the system, the distance from the sink or well within which flow is occurring will continually increase; that is, thc region of disturbance will grow. If some rigid boundary such as a fault is reached by the disturbance, this area will cease to grow; but if some movable boundary is reached, such as a water-oil contact, the area will grow on out into the water, although rate of growth may and almost always does change. The relation between amount of pressure drop and amount of fluid flowing at any point and at any time in an aquifer depends on such factors as compressibility and viscosity of the fluids, the porosity and permeability of the rock, geometry of the whole system and withdrawal rate or pressure drop. With these factors known, it is theoretically possible to calculate the pressure-flow behavior of the system, However, in practice true solutions to the problem are next to impossible due to complexity of reservoir systems. A number of approximate methods of solution have been developed based on various simplifying assumptions. One frequent assumption is that the water-oil contact can be located and equations defining oil reservoir and aquifer solved separately by assigning values to various parameters so as to match past pressure and production history. Usually the properties of the aquifer are not known, since few, if any, wells are drilled through the aquifer; but the water influx and the pressure at the reservoir boundary are known over some time. If it can now be assumed that the aquifer is circular, pie-shaped, or linear, and that it has uniform properties, it is possible to fit a theoretical dimensionless curve to the past aquifer performance history and therefore calculate future water drive. These theoretical curves are available in the literature,1,2,3 Of course, the assumption of uniform aquifer properties is almost always somewhat in error. Fortunately, however, moderate variations from the average have little effect on behavior of the system; and, hence, the best fit of a theoretical curve is frequently satisfactory. In other cases variations in aquifer properties and geometry are large enough that none of the available theoretical curves will give an acceptable fit of the data. In these cases, methods of fitting the data with various electrical analyzers have been developed.1,2' It is the purpose of this paper to present an approach

Discussion of the paper of GEORGE S. Rice, presented. at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2459 to 2492. WILLIAM GRIFFITH, Scranton, Pa.-I notice in the discussions and literature that emphasis is placed on rock dust, shale dust, and limestone dust, and I infer that these different. sorts of rock are ground up to produce this dust. -Is that right? MR. RICE.-That is correct, but we do not have to grind the limestone dust we are using in the experimental mine, as that is obtained from a quarry, and is used just as it comes; we can get it very cheaply, as it is a by-product of the quarries. MR. GRIFFITH.-Have any experiments been made with ordinary dirt out of the fields; could not that be used as ground dust? MR. RICE.-If you dry it and powder it enough so it will float in a, strong air current it might be all right for the barriers, but if it is damp there will be a tendency for it to mat together; then it would be quite useless for making a dust cloud. There might also be another disadvantage if used through the whole mine, if it had very much free silica in it, which is bad for the lungs. Limestone and selected shale dust would not affect the health of miners. MR. GRIFFITH.-In order to do very much good with any of those barriers, they ought to be rather extensively used throughout the mines, and there are few mines that have facilities for grinding up this rock into such a fine dust. If the ordinary earth from a plowed field could be used, even if it were not quite so good, it is more accessible and very much cheaper; therefore, in using it, with the universality of the supply through-out the country, it would tend to stop explosions. MR. RICE (communication to the Secretary*).-In closing, it is well to again emphasize that I do not advocate barriers being a "cure-all" for explosions. It will be generally agreed that prevention is best, not only by means of improved methods of using explosives, and ventilation to prevent accumulations of firedamp, but also by either thoroughly wetting the dust throughout the mine, or else so treating it with rock dust or other inert dust that an explosion cannot start. From my observations I believe that rock dusting. is a practicable method, and has the merit of visibility, and remaining effective for considerable periods, whereas the watering method has to be daily followed up, and if neglected for a short period the mine may become in a dangerous condition. The Germans

Jan 4, 1915