Search Documents

By Edward L. Fidler, Thomas E. Finch

Thin seam coal mining in the western US nominally equates to recovery of stray seams associated with thicker, major seams. The thin or stray seams encountered are generally recovered, but not in all cases. The alternative to extraction is, of course, spoiling. The majority of thin seams are encountered somewhere in the overburden above the major seam or in the parting between thick seams. Although some are true strays and appear anywhere in the geologic sequence, others might be classified as thin "rider" seams immediately above or below a thick seam and separated by some equally thin parting. For the purpose of this discussion, stray or thin seams are defined as those which are less than 1.2 m thick or represent less than 10% of the expected extractable coal. [Figure 1] is a graphic representation of typical thin, stray, or rider seams which actually appear in a western operation. Operationally, stray seams create irritating scheduling problems and require special handling techniques which do not always lead to efficient equipment utilization. Additionally, coal recovery from a thin seam is considerably less than the 95% usually recovered from thick seams. Higher recovery in thin seams leads to dilution problems, which depreciates Btu quality, and most western coals are not in a position to lose heating value. Thin western seams also undulate and pinch or swell more than thick seams, and this leads to more difficult recovery. Often they are associated with equally dark carbonaceous shales and visual selectivity is difficult at best during daylight hours. Resource Recovery Regulations Thin seam recovery in western mines is encouraged by both federal and state regulations and by the mining industry's concern for total resource recovery. [Table 1] lists the western coal states and their recovery regulations. The federal regulations are found in the Surface Mining Control and Reclamation Act of 1977. They state, "General performance standards shall . . . require the operation as a minimum to … conduct the surface coal mining operations so as to maximize the utilization and conservation of the solid fuel resource being recovered." Economic stimulation for thin seam recovery appears to be marginal or at the least controversial. Scheduling and operational problems often outweigh the nebulous profits created by engineering analysis. The only alternative to extracting thin seams occurring above major production seams is to strip directly through them and lose the resource to the spoil pile. Although this is not palatable to environmental emotions or resource promoters, it is the most simple expedient to operations people.

Jan 1, 1981

By M. K. Barnett

Engineering research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency—i.e., the attain- ment of the maximum amount of reliable, useful information relating to the influence of, the factors on the property of the product or characteristic of the process, for the least expense—is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modern methods for the analysis and evaluation of experimental data. The Present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1948

By M. K. Barnett

Engineering research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency—i.e., the attain- ment of the maximum amount of reliable, useful information relating to the influence of, the factors on the property of the product or characteristic of the process, for the least expense—is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modern methods for the analysis and evaluation of experimental data. The Present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1948

By J. M. Callow

THe results obtained by pneumatic flotation throughout the country on all classes of ore, and the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practicc. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cyeloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by Dr. Rudolf Gahl on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. CoMPABATIVE SENSITIVENESS AND ATTENDANCE Concerning the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that, with the exception of about 24 days at the end of the testing period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the concIusions drawn on page 499 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 1, 1917

By H. R. Brannon, F. M. Perkins, Weldon O. Winsauer

Both the abnormal resistivity exhibited by shaly reservoir materials and their potential are due to adsorption of ions. Interrelationships between the two have been derived and verified by laboratory results. These relations which have resulted from this work may be used in a qualitative manner to estimate whether or not a particular shaly reservoir contains hydrocarbons, and also to estimate the porosity of shaly sands. INTRODUCTION In spite of the progress which has been made in the last decade toward a better understanding and utilization of the electric log, there remain a number of problems in the interpretation of the log. One of these which is often troublesome is that of divining the nature of the fluids in sandstones or carbonate rocks which contain appreciable amounts of shale. It was shown by Patnode and Wylliel in 1949 that shaly rocks exhibit an abnormally low resistivity when saturated with solutions of low ionic concentrations. This phenomenon has been demonstrated to be due to the adsorptive properties of shale or clay in the rock.' In estimating the fluid content of shaly sands or carbonates from the electric log, it is desirable and sometimes necessary to correct for the abnormally low resistivity. A similar correction is likewise often necessary if attempts are made to estimate the porosity of a stratum from resistivity measurements. The correction may be made from data obtained on core samples and from information on salinity of interstitial water. Cores, however, are not always available. Moreover, even if cores are at hand, their examination is time-consuming. It would be most desirable, therefore, to make corrections of this nature from the log itself. Since both the abnormal resistivity and the potential' are consequences of the adsorption of ions on shale, it should be possible to utilize the potential curve to give better interpretation of resistivity data obtained in logging shaly materials. The work described in following sections was directed toward this end. THEORY Relation of Resistivity of Shaly Reservoir Rock to Adsorpttve Properties In discussing the effect which the presence of shale or clay exerts on the resistivity of a reservoir rock, it is convenient to make use of the resistivity factor.4,5 This quantity has been defined as the ratio of the resistivity of the rock when it is completely saturated with an electrolyte to the resistivity of the electrolyte itself. When the rock, such as a clean sand or carbonate, is free of shale the resistivity factor is virtually independent of the ionic concentration of the electrolyte used to saturate the sample, so that F = R0/Rw = constant for a clean rock . . (1) where F is the resistivity factor, R0 is the resistivity of the rock saturated with electrolyte, and Rw is the resistivity of the electrolyte. When the rock contains argillaceous material, the resistivity factor as defined above is no longer independent of the concentration of the electrolyte used to saturate the rock, but decreases as the ionic concentration of the electrolyte decreases. In explanation of this behavior, it is instructive to consider a sample of shaly porous rock placed in contact with a large volume of a dilute electrolyte. The sample is considered to become saturated with the electrolyte, and to attain equilibrium with it. As a result of adsorption by the shale surfaces within the rock, there is a greater concentration of ions in the solution adjacent to the shale particles in the interstices of the sample than there is in the external solution with which the

Jan 1, 1955

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 768 C (1414 F), the metal becomes nonmagnetic, and at the "A, point," 910 C (1670 F), it undergoes a change in crystalline form to become gamma iron. In the range 768 to 910 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1400 C (2552 E), it changes into delta (d) iron, which is identical with beta or non- magnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1537 C (2800 F); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A, point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always true. For example, the specific heat reaches a sharp maximum at the A2 point although no trans- formation occurs. (See Fig 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an ap-

Jan 1, 1951

By Philip Henry

THERE is a difference of opinion among engineers on the subject of depreciation in general, and still more on its application to any given case. The committee which was appointed by the American Society of Civil Engineers to make a report on Valuation of Public Utilities, states "There is no subject connected with valuation about which there are more diverse views than those relating to depreciation;" and in the discussion which took place upon the presentation of the preliminary report of this committee in January, 1914, that part of the report dealing with depreciation called forth more discussion than any other. From this discussion it was evident that the word " depreciation" was not always used in the same sense, so it is quite important that some definition be adopted. As this paper relates to the proper method of treating depreciation by corporations or individuals operating oil properties, both of which must make a return of annual net income to the government in connection with the income tax, it will be in order to adopt the definition of the Internal Revenue Bureau. Under date of Mar. 29, 1910, the Commissioner of Internal Revenue of the Treasury Department stated "Deduction on account of depreciation of property must be based on lifetime of property, its cost, value and use." Again, on Form 1035, "Return of Annual Net Income" for miscellaneous corporations (Section 2, Act of Congress approved Oct. 3, 1913), a deduction from gross income is allowed for "Total amount of depreciation for the year." This item is defined more particularly as follows: "The amount claimed under Item No. 5 (b) for depreciation should be such an amount as measures the loss which the corporation actually sustains during the year in the value of buildings, machinery, and such other property as is subject to depreciation on account of wear and tear, exhaustion, or obsolescence. The amount taken credit for on this account in order to be allowable should be so entered on the books as to constitute a liability against the assets of the corporation. The amount claimed under this item should not cover losses in the value of stocks and bonds. Decrease in the book value of securities owned, so far as such decrease represents a decline in the actual value of such securities, should be deducted under item 5 (a) of the return.

Jan 1, 1915

By J. J. Gilman

THEORIES of fracture in metals have been based primarily on the dependence of fracture strength on grain size. This dependence was first observed by Masing and Polanyi.l These workers, as well as 0rowan12 and Davidenkov and Wittman,' thought the grain size could be equated with the crack size in the Griffith condition for crack propagation.4 In this way they could account for the observed proportionality between fracture stress and the reciprocal square root of the grain size. The chief results of recent investigations of the fracture strength of polycrystals are summarized in Fig. 1. Low for iron,5 Petch for iron,' Greenwood and Quarrel for zinc, Petch and Zein for zinc,' and Hauser, Landon, and Dorn for magnesium'' have all found that the fracture stress of a polycrystal is proportional to the reciprocal square root of the grain size. Also, they find that, for large grain sizes, the fracture stress lies near the extrapolation of the yield-stress curve determined at small grain sizes; where measurable plastic strain precedes fracture. Low9 has gone a step further and shown that, in Range 1, the fracture stress in tension is almost identical to the yield stress in compression for a given grain size. Homes and Gouzou, 10 and Low also have shown that, in Range 2 of Fig. 1, microcracks form when the yield stress is reached, but they do not cause failure until the stress reaches a much higher value. The fact that yielding always precedes fracture suggests that fracture is induced by plastic flow. A mechanism by which this might occur was first proposed by Zener.11 He pointed out that blocked dislocations would cause stress concentrations which might cause fracture. The blocking would be caused by grain boundaries. This idea has been developed by Eshelby, Frank, and Nabarro,12 by Koehler,13 and by Stroh.14 By means of etchpits blocked dislocations have been observed in brass by Jacquet,15 in zinc by Gilman,16 and in lithium fluoride by Gilman and johnston. The blocked-dislocation theory and the experiments that bear on it have been summarized by Mott.18 One of the strong points of the blocked-dislocation theory is that it can explain the grain-size dependence of the fracture stress in a natural way. However, Low9 has pointed out that the theory is not satisfying when it is considered quantitatively. Gilman10 also has criticized the theory and presented an alternative interpretation of the relation between fracture stress and grain size. Since the blocked-dislocation theory is not the only theory that can explain in the grain-size effect, it is necessary to find other evidence either to support or deny it. In this investigation the following points were studied: 1) If blocked dislocations normally cause fracture, then the fracture stress ought to be very high in the absence of plastic glide. Is it? 2) If dislocations must be blocked in order for metals to fracture, then certain types of grain

Jan 1, 1959

By J. B. Austin, R. L. Rickett

MEASUREMENTS Of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even interpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low, a medium, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0% ash, as follows: from low-volatile anthracite, 0.7%; from medium-volatile coal, 1.0%; and from high-volatile coal, 2.3%. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0% or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a convc.ntiona1 dense-media washing plant. Anthracite preparation practices during much of the industry's history were geared to maximum recovery of the larger sizes, pea through egg, which were used in hand-fired, domestic furnaces. Those sizes were cleaned to meet trade requirements, and the smaller sizes were usually higher in ash content. The impression, thus, was that ash content of anthracite always increased as the sizes got smaller. It was presumed that it was impossible to wash the finer sizes to extremely low ash contents. Following World War 11, the classical domestic market began to decline and the finer sizes assumed an increasingly large share of the market. For example, in 1949l 61% of the production was still pea and larger. Fig. l2 shows that -by 1955 these sizes accounted for only 50%, and in 1965, they were only 39% of the total anthracite produced. With the reduction in the market, increased quality was demanded, especially in export markets, and an increasing number of dense-media magnetite washers were installed in new and existing cleaning plants. In 1965, the coarse coal prepared at 59 breakers in the anthracite fields was sampled by the U.S. Bureau of Mines (USBM); approximately 50% of these plants were equipped with dense-media magnetite washers.3 Since 1950, more attention has been focused on the use of finer sizes for numerous industrial uses, including iron-ore sintering, pelletizing, foundry coke-making, cement manufacture, production of calcium carbide, and of carbon electrodes, etc. Most industrial uses require relatively clean anthracite, such as 10 to 11% ash for sintering and foundry coke, 7% for aluminum melting-pot cathode carbon, and 5% for carbide production. Hence, cleaning methods have been improved to the extent that dense-media washers, hydraulic cyclones, and flotation cells have been introduced as fine-coal-cleaning devices. It is now possible to wash the buckwheat, rice, and barley sizes (9116 X 3132-in.) to ash contents as low as 8 to 10% in dense-media devices, but washing the -3132-in. sizes to those limits presents more difficult problems, due mainly to the fineness of the material. This USBM investigation was conducted to determine the amount and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. The goal was to reduce the ash content to a level acceptable for industrial carbon uses, including electrode manufacture, which generally requires an ash content of 1% or less. While low-ash content is of primary importance in selecting industrial carbons, the amounts of other constituents are also important, including iron, silicon, titanium, nickel, vanadium, and sulfur. They were not considered in this work, since their occurrence in deashed anthracite has been studied elsewhere.4 The results of the present investigation were used to design a flowsheet, suggesting a method for producing ultraclean anthracite as part of conventional preparation practice, using dense-media vessels, crushers, pulverizers,

Jan 1, 1970

By Herbert H. Uhlig

ALTHOUGH the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldlo summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.15 per cent carbon. He noted: From these comparisons it will be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable. Ib His data showed that alloys containing 4 to 10 per cent manganese water-quenched from 1000°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 870°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loringa reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 540°C. (1000°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.15 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <0.001 per cent P). In this paper it is shown that of the low- carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from 1000°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

By George W. Small

The ore, as it is raised from the mine, has all average assay-value of $11 per ton, chiefly in the form of free gold. All the ore goes directly to the stamp-mills, of which there are two. The older and larger mill contains sixteen batteries of five stamps each, with one Frue vanner to each battery. The new mill has eight batteries of five stamps and two Frues to each battery. The large mill is driven by Leffel turbine wheels, with a pressure of eighty feet, and a consumption of 600 miners&apos; inches of water. The smaller mill is driven by "hurdy-gurdy" wheels with a pressure of about 550 feet and a consumption of 150 inches of water. At both mills the tailings from the stamps pass over about 20 feet of plates on their way to the Frues. In each set of plates the first or upper one is copper, the rest are so-called silver plates. The bullion from the stamps is about 800 fine in gold and 200 in silver. The concentrates from the Frues average from 11/4 to 1 ; per cent. of the ore stamped. They very rarely exceed 2 per cent. I was unable to get the exact assay-value of the concentrates, but it is said to vary between $100 and $200 per ton. The concentrates are treated at the chlorination works at the rate of one hundred tons per month. The capacity of the works is somewhat greater than this, but as the supply of concentrates is limited it is not deemed advisable to work them up any faster. Care is taken to keep the concentrates always damp until they are put into the roasting furnace. If this is not done, a decomposition of the pyrites begins, forming lumps which do not roast, and which consequently cause a loss of gold in the residues from leaching. A Fortschaufelungsofen is used for roasting. Its dimensions, incloding fire-box, are 12&apos; X 80&apos;. The hearth is one continuous plane, but the charges, of which there are three in the furnace at one time, are kept entirely separate. The furnace-men call the three compartments, the "drying," the " burning," and the " cooking" compartments. In the middle, or "burning" compartment, the ore is spread

Jan 1, 1887

By C. L. Berrien

Many fires have occurred in the mines of Butte in recent years, and while all have been of a serious nature, simply because they were mine fires, six of them have been especially dangerous in respect to loss of life and property, and the expense of extinguishing or controlling them. It is not my intention to discuss the relative merits of methods used in fighting these different fires because the conditions under which they occurred varied in each case, and it was not always advisable to expend the large sum of money necessary to actually extinguish them if they could be bulk-headed off from the rest of the mine. It is needless to say that everything possible has been done to check all fires at the beginning, but without success in some cases; and it has then become necessary to bulkhead all connections to them, in which state several now exist. The mine fires of Butte, or fires in any mine, may be divided into two classes, namely: Those occurring in accessible workings, and those occurring in inaccessible workings; because these two conditions govern to the greatest extent the methods of fighting fires. Accessibility and inaccessibility in the case of mine fires concern not only new open workings and old closed workings, respectively, but also the condition of the ventilation in and about those places. When a fire is accessible at the start it should not be difficult to confine it to a small area and extinguish it in a relatively short time, but when it is impossible to actually reach a fire in old filled, abandoned workings, or there is no opening by which the gases may be conducted away from the fire zone, then the time consumed in changing those conditions permits the fire to increase to such an extent that it is a long, hard fight to overcome it. These different conditions have been met in Butte, and of the six fires of serious proportions the Steward mine fire and the High Ore-Modoc mine fire were in new accessible workings and were extinguished in a month or so. The Anaconda mine fire, the Leonard-Minnie Healy mine fire, the West Colusa mine fire, and the Mountain View mine fire, were all inaccessible. The Anaconda mine fie started about 25 years ago and though safely bulkheaded is still active. The Leonard-Minnie Healy

Jan 1, 1916

By T. A. Rickard

Among the gold-deposits discovered in recent vears none is more extraordinary in richness or interesting in structure than that of the famous mine at Mount Morgan. At a time when but few Australian mines were known to the world outside the colonies, Mount Morgan was quoted as an occurrence, unusual not only in its origin (for it was said to be dye to geyser-action) but also in the purity of its gold. The mine is situated just within the tropics, twenty-six miles southwest of Rockhampton, in central Queensland. Queensland attained in 1889 the first place among the gold-producing colonies of Australasia, a position previously always held by Victoria. In that year Queensland produced 737,822 ounces, while Victoria cape second with 614,838 ounces. Of the four chief mining districts Rockhampton stood first, as the following figures show: Quartz crushed, Yield,. Average per ton, Tons. Ounces. Oz. Dwt. Rockhampton ,....81,138 340,669 4 4 Charters Towers,.. .. 109,328 165,551 1 10 Gympie,.....106,625 112,847 1 1 Croydon,.....29,423 51,156 1 15 It should be added that Queensland has but little alluvial mining, the total output from this source in 1889 being only 5044 ounces, none of which came from the four principal gold-fields. Leaving out Rockhampton, the output of which is practically that of the Mount Morgan mine, it will be noted that the more northerly goldfields show the highest average (Gympie being furthest from and Croydon nearest to the equator). This is largely explained, however, by the increased cost of milling, due chiefly to the want of water for batteries and the consequent economical necessity of selecting high-grade material only for crushing. During the year ending November 30, 1889, the Mount Morgaq

Jan 1, 1892

By Richard G. Warren, Michael M. Minor, Gayle J. Thomas

INTRODUCTION Los Alamos Scientific Laboratory (LASL) initiated its effort in the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR), a part of the Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program, in late 1975. Since that time, LASL has completed sampling of the Rocky Mountain states of New Mexico, Colorado, Wyoming, and Montana at a density of about one water or waterborne sediment sample per 10 km2 and has sampled about 85% of Alaska at a density of at least one per 25 km2. Analytical results for these samples are reported by National Topographic Map Series (NTMS) quadrangle. All collection and analytical procedures have been standardized from the outset (Sharp, 1977; Sharp and Aamodt, 1978). Until early 1979, only uranium results were reported for these samples; thereafter, results include analyses for at least 42 additional elements in the sediment samples. Each LASL HSSR report also includes a discussion of the relationship of these analytical data to known or possible uranium resources; more recently, these data have been re- examined for their relationship to resources for other metals (Beyth et al., 1980; 1980a). Analytical results for LASL HSSR sediment samples are both comprehensive, including 43 elements, and precise, allowing close inter-comparison of data between quadrangles. A recent HSSR study shows that elemental concentrations in sediment samples from the Dixon Entrance quadrangle in Alaska are insensitive to the choice of sieve size fraction and do not vary significantly between stream locations a few meters apart, except for extremely high elemental concentrations (Warren, et al., 1980). Elements that are particularly reproducible include thorium, hafnium, and the .ram earth elements. Fortunately, sensitivities for these elements, which are often associated with uranium, are excellent by the nondestructive analytical technique of neutron activation analysis that LASL employs. Wet chemical techniques may not always give reliable results for these elements in sediment samples due to the difficulty of dissolving the resistate mineral phases that normally contain these elements. LASL has recently open-filed results for a large number of NTK3 quadrangles; to date analyses have been reported for about 605 of the quadrangles within the states of the Rocky Mountain region. As a result, uranium analyses am now complete for all sediment samples collected from the state of Wyoming. We have chosen to sumnarize the analytical results for Wyoming and portions of adjoining states hereafter termed "the ~ Wyoming regionn (Fig. 1 ) ; nearly 24 000 uranium analyses and nearly 17 000 analyses for 42 additional elements are available for sediment samples collected from this area. The DOE open-file report numbers are shown in Fig. 1 for reports open filed before September 1, 1980. The Wyoming region provides an ideal area for an examination of regional geochemical patterns ex- hibited by sediment samples. It is endowed with a variety of exposed geologic units and with widely distributed uranium districts associated with host units of several ages. However, discussion will focus on rock units of Eocene and Precambrian ages because they are widely exposed and host the majority of the uranium resources within the region (Fig. 2). Miocene units are also widespread and host mineralization in the Brown&apos;s Park Formation (Fig. 2). Epigenetic uranium mineralization occurs in sand- stones of lower Eocene age such as the Wasatch, Battle Springs, and Wind River Formations whereas vein type mineralization occurs in Precambrian crystalline rocks. Precambrian rocks within the region consist of a variety of granitic and meta- morphic rocks with l .4-2.8 billion year ages, except within the Uinta Arch, where they consist of a sequence of very low grade metamorphosed or unmetamorphosed 1.0 billion year old sedimentary rocks. Precambrian rocks have served as sources for much of the clastic material comprising the lower Eocene units, and may also have provided the source for the uranium in mineralized Eocene or Miocene sandstones (Stuckless, 1979). The remainder of this paper describes the relationship of elemental concentrations in HSSR sediment samples to exposures of Eocene and Precambrian rocks. The results are used primarily to determine where these Precambrian rocks might provide the most suitable uranium source areas and to infer the direction of transport toward adjacent depositional basins during the Eocene.

Jan 1, 1980

By Thomas Lane Carter

The history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers in the mines which the white men started. The Kaffirs of South Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man&apos;s civilization. They are a virile race, and so far the vices of civilization have not killed them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribes in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country are much finer workmen than the degenerates from less favorable sections. It is universal in South Africa to speak of the Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a a boy," and in this paper the word " boy " is synonymous with Kaffir.

Jan 1, 1909

By Henry Hebley

IN recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and clean-ing of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal.

Jan 1, 1933

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C&apos;, D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C&apos;, 70 ft.; C&apos; to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By D. Harrington

Efficient ventilation of metal mines consists in having such complete control of air currents that there is always supplied at placcs where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet ventilation is only too frequently neglected, especial1y in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years&apos; study of miners&apos; consumption, the writer is convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 1, 1923