Search Documents

Carlisle: I'm in the office of Comar Wilson in London. Comar is going to be good enough to talk about some of the very interesting things that have happened to him during a full, active, exciting life. Let's start in and find out where you were born, where you went to school, etc. Wilson: My parents lived in the heart of the Lake District in Cumberland, England. My father had about a half-interest in a small lead mine which he ran. He was quite non-technical, but he ran it.

Jan 4, 1965

By John Cogan

INTRODUCTION Lake tapping is a method of blasting an intake into a body of water from below the natural water surface without first lowering that surface or installing a protective cofferdam around the tap hole. Lake taps are done by first excavating a tunnel almost to the water/rock contact and then blasting out the final protective rock plug at one time to allow water to suddenly inflow into the tunnel from the lake. This procedure can be done "dry" or "wet." In the dry method the tunnel is empty of water before the final plug blast while in the wet method it is partially filled with water. This paper describes a wet method lake tap as performed at Alaska Power Authority's Tyee Lake Hydroeletric Project in southeast Alaska. The Tyee Lake project is located approximately 40 miles southeast of Wrangell, Alaska, in a glacially formed valley called the Bradfield Canal. The project consists of a powerhouse located at sea level on the canal, a system of tunnels and shafts connecting the powerhouse to Tyee Lake at elevation 373 m (1225 ft), and an 129 km (80-mile) electrical transmission line leading from the powerhouse to Wrangell and then Petersburg, Alaska. Tyee Lake itself is a natural lake gouged out of the rock by glacial ice during the last ice age. The objective of the project was to tap into the lake and use the water as a source for power production. The techniques used for lake taps have been developed in Norway where conditions are favorable for their use in hydroelectric proj¬ects. Over 100 have been performed. In the United States the Tyee

Jan 1, 1984

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By James K. Stanley

PREFERRED orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.1 In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurgical literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanical properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important in- formation, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational under- standing of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing 'stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required-it is only necessary punch or machine a disk of the sheet material and insert it into the testing device.

Jan 1, 1943

By Frank Gilbreth

THE problem, of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community, without placing the cripples into competition with any existing class of workers.

Jan 4, 1918

By Donald W. Scott

GENERALLY speaking, there is nothing very difficult about taking good micrographs of photogenic thin sections or grains with a petrographic micro-scopecamera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. I[a]) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. I[b]) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this is an incorrect interpretation is evident by reexamining the micrograph of Fig. I[a]. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. is the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1946

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep under-ground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county pro-vides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest com petitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By D. M. Lewis, R. C. Emmett, B. C. Wojcik, F. A. Baczek

The ElectroSlurry™ electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon cathode, while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes. The dust is processed through several stages consisting of leaching, copper precipitation, ElectroSlurry electrowinning, and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1981

By G. R. Speich

The age-hardening of Fe-18 to 21 pct Ni marten-sites containing small amounts of titanium, aluminum, copper, or molybdenum has been studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electyon-probe microanaly-sis of the extracted precipitates was also performed. The effects of temperature and composition on the aging kinetics have been studied in detail for Fe-20 pctNi-Ti martensites. All the martensites hardened on aging at 400" to 500 "C with a single aging peak. In the Fe-20 pct Ni-Ti martensites hardening was associated with the formation of a fine dispersion of NisTi. No precipitation was observed in an Fe-21 pct Ni-2.6 pct A1 alloy, although the hardness increased from 327 to 545 Dph during aging at 500°C. Copper was precgitated from an Fe-20 pct Ni-10.7pct Cu alloy, at least during the later stages of age-hardening. Hardening in an Fe-18 pctNi-5pct Mo alloy was associated with the precipitation of an intemzetallic compound tentatively identified as NisMo. The formation of austenite and the recovery of the defect structure of the martensite occur simultaneously with the normal precipitation processes &ring aging of these alloys. THE age-hardening of substitutional iron-base martensites is an important subject for study since age-hardening is one of the principal means of strengthening the substitutional iron-base martensites in precipitation-hardening stainless steels1 and maraging steels.a~4 In contrast to Fe-C martensites, these martensites are relatively soft and ductile in the as-quenched condition, due to the low solid-solution hardening effect of the substitutional elements as compared to carbon. Also, these martensites are hardened by aging at low temperatures in contrast to Fe-C martensites which generally soften on tempering. Titanium and aluminum, singly or in combination, as well as copper and molybdenum, have been the principal alloying additions to stainless steels to obtain an age-hardening reaction.' Ti-A1 or Co-Mo-Ti combinations have been used in the case of maraging steels.3"4 The present work has been confined to a study of the age-hardening characteristics of an Fe-18 to 21 pct Ni martensite to which small amounts of titanium, aluminum, copper, and molybdenum were added in order to study the effects of each alloying element separately. The age-hardening characteristics of these alloys were studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electron-probe micro-analysis of the extracted precipitates was also performed. The types and dispersion of precipitates, the formation of austenite, and the recovery of the defect structure of the martensite all were studied. EXPERIMENTAL PROCEDURE Alloys. The compositions of the alloys studied are listed in Table I. The level of 18 to 21 pct Ni was chosen to assure complete transformation to martensite on quenching and is the same nickel level used in maraging steels. The concentrations of titanium, aluminum, copper, and molybdenum were chosen after a study of the and Fe-Ni-MO' ternary diagrams indicated how much of each alloying element could be dissolved in austenite. Alloys with 2 and 4 pct Cu were also studied, but these did not show precipitation hardening at the nickel levels studied and will not be discussed further. The alloys were prepared from electrolytic iron and high-purity* nickel, titanium, aluminum, copper, and molybdenum by vacuum melting of 20-lb heats. These were vacuum-cast into two 8-lb ingots. The ingots were hot-rolled at 1100°C to 1/2-in. plate and subsequently cut into 3/8-in. cubes. The cubes were sealed in evacuated quartz capsules and solution-treated for 16 hr at 1100°C, except for the Fe-20 pct Ni-10.7 pct Cu alloy and Fe-21 pct Ni-2.6 pct A1 alloys which were solution-treated for 16 hr at 1300" and at 1250"C, respectively. Metallographic examina-

Jan 1, 1963

By E. S. Bumps, M. Baeyert, W. F. Craig

SOME time ago during a study of impact properties of tempered martensite,1 it was postulated that the consistently good ductility of tempered martensite might be caused by its relatively small and peculiarly shaped ferrite grains. The fer-rite grains of tempered martensite have approximately the same size and shape as the martensite "needles." Thus they form an interlocking mass of needle-shaped grains quite different from equiaxed or lamellar ferrite grain structures. When the common mechanical test methods are applied to steel, variations are often observed in the ductility of specimens that have closely similar hardness and tensile strength values. The ductility so measured appears to be structure dependent. When steel from the same heat has been heat treated to produce different structures with the same hardness, the elongation and reduction of area values from the tensile test and the transition temperature determined by the notched-bar impact test vary according to whether pearlite, tempered martensite, or other structural constituents were produced by the heat treatment. It has been widely recognized that tempered martensite gives a consistently good performance, when tempered to the same hardness as many other structures with which it has been compared. In recent years the isothermal transformation of austenite to specific structural products and the quantitative evaluation of the character of these products with respect to their nature and response to deformation has received considerable attention. The objective of the present study was to pursue somewhat further the dependence of ductility upon structure; specifically, it was desired to ascertain whether ferrite grain structure, including both shape and size of the grains, can account for the consistently good performance of tempered martensite in the notched-bar impact test. It was thought that a simple experiment would indicate whether the ferrite grain structure plays any part in the good ductility exhibited by tempered martensite in contrast to other steel structures with different types of ferrite grains. By determining the impact transition temperature, it was proposed to compare spheroidites having similar carbide particle size and spacing but obtained in such a manner that their ferrite grain structures would be very different. Spheroidite obtained by tempering martensite, with its small, needle-shaped grains, was to be compared with spheroidite from pearlite. If the latter is produced by sub-critical annealing, the ferrite grains correspond to the pearlite colonies. Thus, if the pearlite was not too coarse, the ferrite grains of spheroidite from pearlite are equiaxed in contrast to the needle-shaped grains of spheroidite from martensite. It was thought that the ferrite grain structure of spheroidite from martensite might depend to some extent upon the grain size of the prior austenite. The austenite grain boundaries limit the maximum attainable size of the martensite needles and thus of the ferrite grains in the derived spheroidite. In order to evaluate any possible influence of prior austehite grain size, spheroidites were to be prepared from martensites that had been formed from fine-grain austenite and also from coarsened austenite. As the carbide particle size and distribution were to be essentially alike in the various spheroidites, the difference would be in the ferrite grain size and shape. Thus any marked difference in transition temperature could be attributable to the character of the ferrite grain structure. There are certain considerations in assuming that these spheroidites would be equivalent in all respects except ferrite grain structure, and an attempt was made to take them into account. One of the considerations was the choice of the carbon content of the steel. An approximately eutectoid steel was selected for two reasons. First, the pearlitic structure would contain no proeutectoid ferrite which might complicate the picture by producing a non-uniform ferrite grain structure in the resulting spheroidite. Then, too, the high-carbon content would inhibit ferrite grain growth during the sub-critical treatment. Another factor to be taken into account was the choice of an alloying element to assure a martensitic structure throughout on quenching the impact specimens. Nickel was chosen, because it is a common alloying element and resides in the ferrite both upon its formation from austenite and throughout tempering. The formation of alloy carbides, or even a large solubility of the alloying element in cementite, would have complicated the interpretation by changing the composition of the ferrite .during spheroid-ization. The possibility of temper brittleness was minimized insofar as possible by using a tempering temperature as high as consistent with the 1 pct of nickel in the steel, namely, 1150°F. While it certainly is not claimed that no difference other than ferrite grain structure could exist between the spheroidites, nevertheless, reasonable precaution has been exercised within the limits of steel metallurgy. It is believed that any large difference in transition temperatures would reflect the difference in ferrite grain structure and that relatively good ductility in the spheroidites from mar-

Jan 1, 1951

By Harlan N. Barton

A commercially available, portable X-ray spectrograph, lightweight and rugged for vehicle or field camp use, was used to determine Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geochemical samples. Investigations showed a relative standard deviation of 1-3%, detection limits of approximately 100 pg/g and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic-absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1983

By C. H. Li, R. D. Carnahan, R. J. Stokes, T. L. Johnston

When silver chloride deforms by pencil glide at temperatures of 26ºand 72°C, grain size has no effect upon the proportional limit and the material necks down to a knife edge under tension. At -196ºC, deformation takes place on fewer slip systems to produce straight slip traces, the flow stress becomes sensitive to grain size and fracture occurs by cleavage from an intergranular source without any reduction in area. THERE are significant differences between the appearance of the slip bands formed in silver chloride and in the alkali halides at room temperature. The bands in sodium chloride, e.g., are fine and geometrically straight, whereas in silver chloride they are coarse and wavy.' Such differences in the slip behavior prompted us to inquire what the effects of grain boundaries might be on the mechanical properties of these solids. As an introduction to a general study of ionic poly-crystal behavior, we have investigated the effect of grain size on the stress-strain relationships in silver chloride at different temperatures. We have chosen silver chloride chiefly because polycrystals can be easily prepared free from cracks and macroscopic voids by conventional techniques. Moreover, as we shall see, the slip behavior can be readily modified by changing the temperature. It will be shown that the effect of grain size on the yield stress of silver chloride is strikingly dependent upon the temperature of deformation and that this temperature effect comes about through a change in the number of slip systems which operate at the onset of plastic flow. EXPERIMENTAL PROCEDURES Polycrystalline tensile specimens were made by recrystallizing cold-rolled AgCl sheet. Thirty-gram quantities of AR grade silver chloride powder were melted in a low heat capacity furnace, cast into cylindrical forms 3/4 in. in dim and approximately 1 in. in length and then extruded with a 16:l reduction ratio into rods 3/16 in. in dim. Extrusion temperatures were varied from room temperature to 350°C. In order to impart various degrees of cold'work to the extruded rod. All extrusions were then cross rolled to sheet 0.040 in. in thickness at room temperature and machined to form tensile specimens having a gage length of 0.750 in. with a width of either 0.250 or 0.145 in.* Annealing was carried out in an air oven at 200°C for periods up to 20 hr. specimens having average grain diameters ranging from 0.024 to 0.40 mm were prepared by varying the extrusion temperature and annealing time in the conventional manner. To obtain specimens with grain sizes larger than 0.40mm, lightly deformed thin prisims of silver chloride single crystals (supplied by Harshaw Chemical Co.) were recrystallized. Grain size determinations were made by an intercept method and revealed that the grains were equi-axed. Laue back-reflection X-ray patterns showed little tendency to form a preferred orientation texture. Specimens which were to be used for the slip band studies were polished by immersion in fresh boiling concentrated NH,OH for 60 sec. They were then etch polished for 10 sec on each side by hand lapping on a stationary velveteen lap wetted with a dilute Hypo solution (5 g of Kodak Acid Fixer in 100 cc H20). Finally the specimens were rinsed in warm water and alcohol, blown dry and carefully mounted in the tensile machine for testing. Tensile tests were performed at three temperatures, namely, 26º, -72º, and -196°C. A screw-driven hard tensile machine was used at a constant strain rate of 0.006 in. per in. per min. Loads were determined with a light- proof ring fitted with A-18 strain gages and extensions were measured with a 0.0001 in. dial gage. Constant level baths of alcohol with dry ice and liquid nitrogen were used to maintain the two lower test temperatures. EXPERIMENTAL RESULTS Reproducibility—In view of the light sensitivity and reactive nature of silver chloride, it was necessary to determine whether reproducibility depended upon either exposure to light or to the condition of the surface. However, during the course of the work it became clear that variation of laboratory lighting

Jan 1, 1962

By A. L. Mular

lnput energy-size modulus relation at small reduc-tion ratios is expressed by Et = (M, -Mt) k;. In some cases 13 is close to Schuhmann's distribution modulus a in value. Experimental results in conjunc-tion with the equation demonstrate the fact that energy input which produced fracture is not expended on unbroken starting material inside the mill at any time. Recently, schuhmann1 derived the Charles equation2 using the postulate that complex com-minution operations can be considered as a summa- tion of many comminution events. The fragments resulting from each event are assumed to follow the Gaudin-Schuhmamn distribution. In his derivation, Schuhmann implies that the size distribution of the total mass of a material is determined by the fraction of that mass actually subjected to comminution. Consider a feed to contain a volume, Vo, of uni- formly sized homogeneous material. After t seconds of grinding, let the volume of broken material be Vo - Vt where Vt is the volume of starting material not yet broken. The size distribution of the broken material is given by: where V is the cumulative volume less than size X, and k, is the size modulus of the broken material at time t. The distribution for the total volume at this

Jan 1, 1962

By Wayne L. Dowdey

With proud humility and keen anticipation, I accepted the office of President of the Institute one year ago, and it is with a great deal of pride in you-our membership that I make this report. You are the reason for a productive and prosperous year for AIME. Superior, good or satisfactory results were experienced in 1978 from almost everything we did as a leading engineering technical society. I recognize and pay tribute to the WAAIME organization. Their work is vital to our efforts, and their programs have proven effective. WAAIME can depend upon our continuing support.

Jan 6, 1979

By George W. Mitchell

THE property of Eureka Corp. Ltd. is located in the approximate geographic center of Nevada, 2 miles from Eureka, the county seat. The great sources of power, the Colorado, Snake, and Salmon Rivers and the rivers of northern California, are 300 to 500 miles distant, and no lines serve areas closer than 150 miles. Fuel for diesel and steam generation is available in Utah, 300 to 400 miles to the east. Eureka's railhead is 80 miles north where two trunk lines cross the county. A spur line serves Ely, 77 miles east. Good highways connect Eureka to the railheads.

Jan 8, 1953

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927