Search Documents

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500' to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast' reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957

By D. R. Knowlton

IF I were a minister, and this were a sermon, and such a passage appeared in the Bible, I would choose for my text: "From whence cometh the oil for our war?" And no preacher was ever more serious than I am. You petroleum engineers recognize that the producing branch of the industry is passing through an era of plenty and inflated potentials into an era of scarcity and unmet allowables. Not too long ago the oil operators of Kansas, California, and Texas were appearing before operators' meetings and regulatory authorities asserting that these States were capable of producing at rates far in excess of what the demand at that time would absorb. Today every oil-producing area in the United States except the Texas Gulf Coast and West Texas is producing close to or in excess of its maximum efficient rate.

Jan 1, 1943

By Carl W. Volz

NORWAY'S metallurgical development, which has extended over many centuries, is intimately associated with that country's unique topography and climatic conditions. It is a rugged mountainous country, with a most irregular shore line, bordered by thousands of islands forming a natural protection for shipping. There are an endless number of lakes, and innumerable rivers and waterfalls, many fed by glaciers and melting snow. Rainfall is abundant. Though half of the country is north of the Arctic Circle, it is warmed by the Gulf Stream, so that the average temperature is about 45°, or 20° higher than other parts of the world in the same latitude. A sub-

Jan 1, 1935

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By R. C. Canby

JUDGE GRANT, in a delightful satire of his, says: "Boston is a state of mind." I think that this same statement might well be made of the metallurgy of lead. I was particularly impressed with this when about thirteen or fourteen years ago I prepared a paper on "Development of the American Water- jacket Lead Blast Furnace." Dividing the time, as I did into ten-year periods, from the commencement of lead smelting at Eureka, Nev. (1870), and showing the tendency for each of the five decades it was evident that the progress had been through a succession of states of mind from the rule of thumb through the ultra scientific, or from what I might call the slag type period up to the present highly developed art. Conservatism has been characteristic of the metallurgist. This may have been most natural, especially with the lead metallurgist, the development of whose art was so entirely in the custom smelting plant, where the metal contents of his ores were paid for in cash and therefore excessive metallurgical losses could mean nothing short of financial bankruptcy. The metallurgist himself was held to a personal account, in these smelting plants. It was the metallurgist who was accountable. In the concentrating plants, if undue losses occurred remodelling of the plant was discussed, but if there were excessive metallurgical losses in the custom smelting plant, a new metallurgist was considered as the remedy. For this reason the tendency was to adhere to recognized practice and to be wary of unusual methods, using the word unusual in the sense in which it is used in Article VIII of the Constitution of the United States, as to punishments and modes of death. This conservatism of the metallurgist was reflected as other branches of metallurgy were developed. We have heard of the wonderful development of flotation, but it had to be introduced over the dead metallurgical bodies of its opponents.

Jan 1, 1926

By Harlowe Hardinge

AN extensive recent trip throughout the mining districts of the Southwest, Central West, an Northwest,' reveals a numbes of interesting conditions that have influenced operators, in both large and small mills, to modify their flow sheets insofar as they pertain to crushing and grinding. The changes made and planned for the future should be of interest. It is interesting to note when traveling through the country, how ideas change and practice is modified, and it is rather amusing to see how milling methods seem to run, more or less, in cycles. New ideas and developments are brought about which run through the industry and are taken up by many of the best and most well informed operators. Some of them will change, sooner or later, back to their old practice; for, like everything .else, what will work well in one place will not necessarily be suited to another. On the other hand, it is often difficult to establish. other practices known to be of value, owing to the natural resistance to make a change, but on the whole, the western mill men seem to be more alive to possible benefits of various modifications than any other engineers with whom I have come in contact in all parts of the world. Mill men in other parts of the world always keep in con- tact with what is being done in the western part of the United States, but it does not necessarily follow that those in the western part of the United States are always right. Some of these changes that have been made and afterward abandoned will be referred to later.

Jan 1, 1929

TITANIUM is one of the most abundant elements in the minerals that make up the earth's crust but its use in industry is only a generation old; yet probably no other important commercial mineral raw material (except possibly magnesium) has undergone more changes and developments in sources of supply, in processing techniques, in uses and applications, in the past 10 years, or stands on' such a threshold of still more advances. Its outstanding use today is as the oxide, and because of its extreme whiteness, high refractive index, chemical stability, and relative cheapness, it has become the white pigment used in the largest volume. New developments in the uses of titanium metal, potential and actual, may surpass the pigment use of the oxide before many years. TITANIUM-BEARING MINERALS Although a number of minerals contain titanium as the principal metal, only a few are of commercial importance. These are arizonite, ilmenite, and rutile. The other oxides, brookite, pseudobrookite, and anatase, occur in a few deposits, one at least of minor importance. The silicate titanite, and the double oxide of calcium and titanium, perovskite, occur in a few deposits in quantities sufficient to be considered as potential ores were not richer deposits of the oxides available elsewhere. Arizonite is a name given by Palmer46a to a mineral found some years ago in minute quantities in Arizona, which has the formula Fe203.3Ti02. Unexpectedly, it was found that the black titaniferous iron oxide found in large quantities on the beaches of many continental land masses corresponds in chemical composition to this formula (although ferrous oxide is always present). No one has yet been able to prove that the commercial mineral on the beaches is truly arizonite, or an allotropic modification of it, since X-ray investigations by Howard Carl and A. F. Gabriel, of the U. S. Bureau of Mines, and by the X-ray laboratory of the Chemical Department at the Experimental Station of the du Pont company, have shown only that the sand mineral gives just a jumble of lines, rather than an identifiable pattern. Lack of a better name,

Jan 1, 1949

By A. V. UDELL

OF all the metals that have from time to time been called the "Wonder Metal," mercury, often called quicksilver, is probably the most deserving of this designation. A wonder metal it must have been to those workers of an earlier day who named it after that Latin god of commerce and gain, characterized as the fleet messenger of the gods and the conductor of souls to the lower world. The word mercury has been used to indicate a carrier of tidings, a bearer of news, a nimble or clever person, a hawker, and a skillful thief. All of these attributes, and more, are recognizable in this metal, the technical terminology of which is "Hydragyrum," meaning water-silver, and from which the chemical symbol "Hg" is derived. Fickle in its occurrence in nature, simple in its metallurgy, illusive in captivity, it serves man in life or death, in war or peace, in commerce, science and arts, in mining, agriculture, and forestry with a versatility found in no other element.

Jan 1, 1929

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By Edward P. Barrett

DURING the past few years numerous references have been made in the technical press and Bureau of Mines Bulletin 270 to sponge iron' and so-called "direct metal" processes. The idea has been prevalent that sponge iron and "direct metals" are cheap commodities. In many instances it has been proposed that these processes be used to treat low-grade ores, utilizing low-grade coals as reducing agents. It is questionable whether or not high-grade sponge iron can be made from low-grade materials. Particles contain¬ing iron oxide and gangue become, upon almost complete deoxidation, particles containing metallic' iron and gangue. The possibility of mechanically separating the metallic iron from the gangue in these particles depends . on the physical characteristics of the particular ore under treatment. Some ores, in which the minerals constituting the gangue break free from the iron oxide upon crushing, may be concentrated magnetically after the iron oxides have been reduced to metal. The finely disseminated ores are least amenable to concentration. In general, high-grade sponge iron can only be made from high-grade raw materials. Sponge iron containing small amounts of sulfur can only be made from raw materials containing small amounts of sulfur or by

Jan 1, 1930

By Lysle E. Shaffer

INCREASING attention has been given in the last decade to the possibilities of mine leasing in the West. The practice as described in this article does not refer to the leasing of entire properties for corporate operation. It is intended to deal rather with the advantages and problems incident to leasing portions of properties to individuals who themselves, individually or in groups, do the actual mining and transportation of the ore. These individuals are sometimes called "leasers" and sometimes called "tributors." The contracts under which they work set up an independent relationship of lessor and leaser, between themselves and the mineowner or operator. This relationship has many advantages to both sides over those created by the ordinary relationship of employer and employe. From the standpoint of the owners there is no liability on independent contractors for industrial injuries, social security taxes, unemployment taxes, or the manifold restrictions of the Federal Labor Relations and Wage Hour Acts and similar state acts where they exist. As the leaser's income depends on the quantity and quality of ore produced, there is a distinct incentive for maximum production of a good grade of ore. This in turn promotes careful mining of the areas under lease. Ordinarily in mining, labor cost is a high percentage of the total cost of operation. Under a leasing system, even if the leasers be allowed to retain half of the gross values that they produce, and the owner or operator gets half, in the case of marginal ore bodies this is ordinarily more than the lessor would realize if the property were worked by day labor. In some instances mineral deposits under a leasing system may become ore, whereas under a day-labor system they would

Jan 1, 1948

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By Eugene McAuliffe

AS this is written, the probability A is that the bituminous coal out- put for 1936 will approximate 420,000,000 tons (of 2000 lb.) with an average working time for all mines of 205 days. The results for 1935 approximated 369,224,000 tons, with the mines working about 185 days. The increase in production of 14 per cent is heartening. In anthracite, it is probable that the preliminary figures covering output for 1935, 51,- 003,000 tons, will be exceeded this year although the percentage of in- crease will almost certainly be small. The substantial tonnage of anthracite illegally mined, estimated to be 3,600,- 000 tons in 1935, with a similar large Lonnage in 1936, is in addition to the figure given above; it represents an open and flagrant disregard of law and property rights. It is hard to understand why the officials of the State of Pennsylvania do not enforce the laws against theft and brigandage, more so when the legitimate employees of the established producing proper-

Jan 1, 1937

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By A. C. Stevenson

IN OUTLINING the various steps taken and the exigences met during the time of unwatering and rebuilding the burnt top equipment at the Hecla mine, the major portion of the detail is omitted and a general description of the experience only is given. All the electrical power lines were out of commission, as were the mine feeder cables. The first effort, there- fore, was to restore electrical connections. The Washington Water Power Co. immediately put a crew to work restoring the power line, it being necessary to rebuild about 4000 ft. of 66,000 volt transmission and about 2000 ft. of 2200 volt feeder. This work was rushed and power was again available at the mine sub- station about 26 hours after the fire. During the same time temporary lighting lines were strung and transformer equipment obtained, so that when electrical connection was resumed the lights were turned on and the dump well lighted that night.

Jan 1, 1924

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

By AIME AIME

AT bottom of this page is a photograph recently taken by a student-John E. Stewart-of the most northerly situated college in the world, the Alaska Agricultural College and School of Mines. It is situated at College, near Fairbanks, Alaska, approximately on the 65th parallel of latitude, and therefore just south of the Arctic Circle. It is farther north than Hudson Bay, and in about the same latitude as southern Greenland.

Jan 1, 1932

By Clyde E. Williams, V. N. Krivobok, C. H. Herty

THE extreme effect of the depression on the steel industry is well illustrated by the fact that the amount of iron ore shipped from the Lake Superior district was the lowest in 47 years. Something over 3 1/2 million tons of ore was shipped in 1932, compared with over 65 million tons in 1929. It is not surprising then that practically no advancement in iron ore beneficiation has been made. Improved research and development work, however, was continued at the Michigan College of Mines in the survey of the lean iron ores of Michigan with reference to the possibility of their concentration; at the University of Minnesota in its large-scale jigging studies of Lake :Superior ores; and at Battelle Memorial Institute in the development of improved jigging of iron ores. The successful operation of the new Hadsel mill at a gold property in California gave such low grinding costs on a quartz ore as to give much encouragement in the iron ore industry for a cheapening of the cost of grinding lean ores for concentration.

Jan 1, 1933

By William R. Chedsey

ALTHOUGH few changes can be reported in educational methods at the mineral technology schools during 1940, other events have taken place of direct interest to, and that will have a profound effect upon, mineral industry education on the United States. In the erection of new buildings, some notable changes have been made on the campus, The U.S. Bureau of Mines Experiment Station at the University of Utah, Salt Lake City, was dedicated on May 20. The construction and equipment of this building cost between $300,000 and $400,000. It will be the general headquarters for the metallurgical division of the Bureau and will have a pronounced effect upon the mineral industries research program at the University.

Jan 1, 1941