Search Documents

By Charles M. Romanowitz

The motivation for the art of dredging for placer mining can be compared in a slight degree to the spread of civilization which started in the Near East and spread both east and west. Dredging started with the "bag and spoon" dredge in the lowlands of Europe reportedly about 1565, went southeast to New Zealand where designs were developed for a bucket-line mining dredge known as the New Zealand type, and westward to the eastern United States where a dredge was developed and used exclusively for excavating. Then it moved to Montana, where it was first used for mining in 1895. The New Zealand-type dredge was imported into California in 1898 (Fig. 1) and was followed shortly by the Montana design. As today, these early dredges were equipped with continuous bucket- line chains, a treatment plant, and a means of waste disposal mounted on a wooden hull. Both types of dredges are complete mining units: they dig the formation, transport the dug materials, and concentrate the valuable ore. After sizing, the fines containing the ore are passed by gravity to the treatment unit, while the barren materials are discharged overboard. By digging the materials to be treated at the bow and depositing all the waste, at the stern, the dredges automatically advance to new reserves without presenting any transportation problems. The main differences between the two types are in the method of holding the dredge in the digging position and in the disposal of the tailings to the rear. The New Zealand type (Fig. 2) uses the headline system with a bow anchor for holding the dredge in the digging position and long tailing flumes or short stackers off the stern for disposal of the barren materials. The California type (Fig. 3) uses box girder spuds projecting into the ground in a vertical position at the stern of the

Jan 1, 1969

By L. E. Wemple

Previous to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, ie., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, z.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was predetermined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into grades suitable for bras4 was that of redistillation.

Jan 1, 1918

By James Gayley

The atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantitiee. At no time since the blast-furnace became an important and widely used apparatus—even when it was operated in the most crude manner—have the variations in composition of the raw materials used been as frequent and as great as the variations in humidity of the atmosphere. Important improvements have been made in the blast-furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing-engines, the increased protection given to the bosh-walls, and the careful preparation of the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least, a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humidity as variable to-day as when first blown into a primitive blast-furnace, appeared to stand as a barrier to

Jan 1, 1905

By William H. Grady

FactoRs entering into the market value of coal are its grade, and the cost of labor, material, and capital. Reduction in these costs cannot be expected in the future, and it therefore follows that greater economy in their use must be accomplished if it is desired to hold the present markets; more tons of product per unit must be obtained in a given time from both men and material, and means devised for increasing the percentage of lump and domestic sizes. This paper is presented for the purpose of inviting discussion and stimulating thought in regard to the influence of methods of procedure and plans of mining, upon the quality of coal, the economical use of labor, material, and capital, and the cost of production. Even the better methods of the present day leave much to be desired, and a review of the reasons and necessities for their use may be of value in pointing the way to more economical mining. The writer does not attempt to discuss untried methods of mining, but rather to state clearly and concisely a summary of the results obtained under the several methods of procedure that have been adopted. In some instances a high degree of concentration has been effected, and comparisons of the results obtained with the results of lesser degrees of concentration form an interesting study. It is believed that much may be accomplished in improving the quality, and in the more economical use of labor, material, and capital, by concentration, and it is to concentration in particular that your study is invited. The writer, who has occasion to visit many mines, most of which are under different management, has been inclined to the opinion that improvement has been retarded in many ways and that mining has not as yet been entirely freed from the early-day practices which were forced upon it. Practices resulting in lack of concentration, to which reference will be made, are: The absence of robbing, necessitating the frequent interposition of barrier pillars; lack of system and of proper supervision, resulting in losses of life and coal. These practices could not well be

Jan 1, 1915

By R. Ebeling, M. F. Ashby

The paper is in two parts. The first develops the formulae and method needed to calculate the size, nu)nber, spacing, and volume fraction of hard or inert particles in the interior of a specimen from measurernents made on an extraction replica; throughout, the spread of- particle sizes in a single specimen is taken into account, and the extraction efficiency of the replica is considered. A method for testing whether the particles are randotnly distributed in space is described, and the spacing of randomly distributed particles is discussed. The second Part describes the application of the method to copper containing spherical particles of silica; the description includes an estimate of the errors involved, and a comparison of this with alternative methods. All parameters except uolume fraction can be determined satisfactorily, and the method offers advantages over other electron-,rzicroscopic techniques when dealing with hard particles in a softer matrix, or inert particles in a chem-ically less inert matrix. 1 HE experimental measurement of sizes and numbers of discrete particles of a second phase embedded in a matrix material from opaque, plane sections has been considered by many authors, notably by Fullman.' It is assumed that, when the specimen is sectioned, the particles are also sectioned, so that the diameters of the circles of intersection of particles with the plane of the cross section ("surface diameters") are measured. It is difficult to derive the distribution of true particle diameters ("volume diameters") from measurements of the distribution of "surface diameters" on a plane section. The measurement of size and numbers of small second-phase particles by transmission electron microscopy through thin foils of matrix containing the particles has been described by Cahn and ~uttin~' and by ~illiard.~ Because of overlap and the fact that particles which intersect the foil surface may be sectioned whereas those in the bulk of the foil are not, it is again difficult to measure the true distribution of particle sizes. The use of replicas for this sort of measurement has not been analyzed in detail. A replica made from an opaque cross section, thus replicating the circles of intersection of particles with the plane of section, is analyzed by Fullman's method and suffers from the same difficulties. Under certain circumstances, however, extraction replicas can be used, and offer a special advantage in that they make the determination of the true distribution of particle diameters particularly simple. It is the purpose of this paper to describe this extraction replica method. Consider the example of an alloy consisting of SiOz particles, whose mean diameter is about 1000A, dispersed in a copper matrix. When the alloy is sectioned and mechanically polished, the particles are not sectioned, because they are much harder than the matrix, and so will be either left in the surface or pulled out whole, and because the particle size is smaller than the abrasive size of even the finest abrasive. The particles are chemically inert in solutions which chemically etch or electropolish the matrix, so that chemical treatments do not section the particles either. (Experimental measurements of particle shape in this alloy confirm this—truncated particles are never seen.) Small, hard or inert, particles are therefore not sectioned when the specimen is sectioned and polished. An extraction replica taken from this polished surface shows the true "volume" diameter of each extracted particle; the distribution of diameters seen on the replica is the surface distribution of true "volume" diameters, and the volume distribution of true "volume" diameters is easily derived from it. The extraction replica method is not subject to the difficulties associated with sectioning of particles, and avoids the problem of overlap from which the transmission method suffers. The method is well-suited for studying hard particles in a soft matrix. Examples are provided by internally oxidized alloys, oxide-dispersion strengthened metals like T.D. Nickel, and carbides, nitrides, and strong intermetallic compounds in metals. It should be possible to adapt polishing techniques in alloys containing softer but inert particles to avoid sectioning the particles (say by electropolishing or etching). The method is tested and illustrated in Sections 8 and 9 by applying it to a dispersion of spherical SiO2 particles in a copper matrix. I) SYMBOLS Symbols are defined where they first appear in the text. Volume fractions of particles are denoted by the symbol f, particle diameters by x, center-to-center particle spacings by D, and numbers of particles by N. Mean particle diameters and standard deviations about these means are denoted by x and a. Both arithmetic (subscript A) and geometric (subscript G) means are employed. In this paper we measure the distribution of true diameters of particles which touch or pass through a random-plane section of the specimen. We may want to know the distribution of particle diameters in the

Jan 1, 1967

By Albert Sauveur

(New York Meeting, February, 1913.) IT is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.1 The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance.

Jan 3, 1913

By Larry G. Hayes

Development of the Bowers-Campbell zinc deposit, located in the Shenandoah Valley two miles northwest of Timberville, Va., was commenced in 1956 by the Tri-State Zinc Co. The occurrence of lead-zinc mineralization in this area has been known for many years, but the first serious exploration program was initiated in 1951 by the geologic staff of Tri-State Zinc Co. Ordovician dolomites. The deposit is approximately 700 ft long, 100 ft wide, and 475 ft thick. Its projected plan has an elongated ovoid shape, where- as the profile appears boot-shaped with the upper portion outcropping. Vertical cross sections show the lense as having been thrust-faulted along certain bedding planes. The movement along these bedding thrusts varies greatly and in one case, has offset the deposit so as to divide it into an upper and lower orebody. The breccia lense strikes parallel to the N 34" E strike of enclosing strata.

Jan 9, 1960

By E. A. Anderson, M. L. Fuller

The copper-zinc phase equilibrium diagram has been the subject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100' to 400' C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the composition at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical conductivity and microscopical methods mere used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-composition relationship. The microscopical method distinguishes, by direct inspection, between the homogeneous solid solution alloys and those having a secondary constituent in addition to the solid solution phase, and thus indicates from the examination of a series of alloys the solid solubility limit.

Jan 1, 1934

By Norman B. Pilling, George P. Halliwell

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. Tin is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper—i. e., copper containing from 0.03 to 0.10 per cent. of oxygen—apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 1, 1926

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By M. B. Ramachandra Rao

THIS paper records the results of the earth resistivity surveys made in the Godavari river in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented.

Jan 1, 1947

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By R. V. Smith

The theoretical background for calculating friction factors for flow in gas wells by two methods is presented. The first method, requiring pressures, temperatures and specific volumes of the flowing fluids at various depths in the well bore, shows how the mechanical-energy-balance equation for vertical flow may be graphically integrated over the actual path of the expansion of the fluid in the well. Thus, assumptions regarding the effective temperature and effective compressibility of the fluid in the well are avoided. The second method presents an equation derived on a basis of the assumptions that both the temperature and the compressibility are fixed at constant effective values throughout the flowing column of gas. The second method provides a convenient and practical means of calculating friction factors for gas wells and lends itself readily to the problem of calculating subsurface pressures in a flowing gas well. The application of both methods to actual test data taken on a flowing gas well is illustrated in the paper. INTRODUCTION As friction factors for the producing strings of flowing gas wells cannot be measured directly and must be calculated from flow-test data, study of the methods of arriving at friction factors is a necessary adjunct to understanding the characteristics of flow in gas wells. There are two methods of calculating friction factors for gas wells; they differ from one another mainly in the treatment of the path of expansion of the fluid in the well. In the flowing well, the energy consumed in lifting the fluid from the bottom to the top of the well, overcoming the friction between the moving fluid and the pipe walls, and increasing the velocity of the fluid as it flows up the producing string is supplied by expansion of the flowing fluid. The available energy is determined by the expansion of the fluid that follows a path determined by conditions of temperature, compressibility and phase changes of the fluid during the expansion. A means of evaluating the available energy in a flowing gas well and determining the proportion of the available energy used in lifting the gas, overcoming friction, and increasing the velocity of flow is developed in this report. Knowing how much energy is consumed in overcoming friction makes it possible to calculate friction factors for given flow rates in given sizes of pipes in wells. Friction coefficients, as used in this report, are dimension- less proportionality multipliers used in the flow equations to satisfy the equality between the terms of the equation. The square root of the reciprocal of the friction coefficient is termed the friction factor. It has been known for many years that friction factors may be computed directly from mathematical formulas based on certain assumptions regarding the temperature and compressibility of the moving fluid in a well. A general equation is presented in this report without assumptions for vertical flow of fluids and a conventional-type equation is derived on the basis of assumptions that fix the temperature and compressibility at constant values. Accurate pressures at the sand faces in wells are required in the method of determining the productivity of gas wells, as outlined by Rawlins and Schellhardt1 in Bureau of Mines Monograph 7. Where measurements are not made with subsurface-pressure gauge; or static gas columns are unavailable, flowing pressures customarily are calculated at the sand face in the well by the use of the well-known Weymouth formula1. Natural gas engineers have realized that errors introduced by the use of friction factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; they also know that such factors are important considerations in testing large-capacity gas wells. Accordingly. present research on the productivity of gas wells at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla., is being directed toward measurement of the pressure loss due to friction in flowing gas wells. It is beyond the scope of this report to show how friction factors vary with rate of flow and in pipes of different diameters, as it is intended only to develop and illustrate the use of mathematical expressions for calculating friction factors from flow-test data. The equations presented apply only to turbulent flow in circular pipes. ENERGY RELATIONS FOR FLOW OF FLUIDS2 The concept of conservation of energy is usually the basis of any study of fluid flow through vertical pipes as in gas wells, horizontal pipe lines, or orifices. In deriving equations, the following symbols are used:

Jan 1, 1950

On the following pages are abstracts of papers published by the Institute during the year 1931 as Technical Publications, Preprints, and in bound volumes. For abstracts of papers that appear in bound volumes in 1931 but that were published as Technical Publications in 1930, see the Transactions, 1930. Papers that appear in the volume in which this list is printed are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 616. The abstracts are grouped as follows: Page Page Metal Mining....................... 578 ing and Metallography of Non-Milling and Concentration........... 578 ferrous Alloys)................586 IronandSteel...................... 580 Coal Division.. ................ 592 Petroleum and Gas.............. 598 Mctallurgy......................... 585 .............. 613 Institute of Metals Division (Found- Geophysical Prospecting......... 613 Metal Mining Use of Models for the Study of Mining Problems. By Philip B. Bucky. (Tech. Pub. No. 425, 12,000 words.)—This paper describes a research project undertaken to provide a means of studying the behavior of weighty structures such as mines, dams, foundations, etc., with models of the same material in the laboratory. The paper shows that in general it can be done. The underlying theory is explained, the apparatus which was developed and built to do this is described, and the results of laboratory experiments with sandstone mine structures are given. There is discussion of the accuracy of results with the present equipment, the model size necessary, and of the size and type of equipment necessary for the obtaining of results of practical value in the field. Milling and Concentration Ball Mill Studies, I. By A. W. Fahrenwald and Harold E. Lee. (Tech. Pub. No. 375. 25,000 words.)—This paper presents the results of an extensive experimental study of some of the numerous elements entering into ball mill grinding. All apparatus used was equipped with ball bearings. Every experiment was accompanied by a power measurement accurate to 0.005 hp. Quartz was used. Each element studied, such as ball load, was varied systematically. Power curves were obtained for the mill for three general sets of conditions; namely, (1) balls only (2) balls and quartz and (3) balls, quartz and water. For each general condition, power curves were obtained for various mill speeds, ball loads and ball sizes. For conditions 2 and 3, feed sizc and weight and pulp dilution also were studied as variables. The mill output, in grams of finished product per unit of time, was obtained for each test. In a general way, output (mill capacity) paralleled the power data and this attached

Jan 1, 1931

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing acid shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subse-quently mineralized by sulphides and barite.

Jan 1, 1937

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the ' alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

By R. T. McLamore

Lack of sufficient native permeability or skin damage caused while drilling wells for in situ leach mining projects may necessitate stimulating injection and production we1ls to increase the leaching rate to economic levels. Such stimulation processes could include acidization, hydraulic fracturing, or explosive fracturing. This paper describes an explosive fracturing process that is being developed primarily to stimulate the production of oil and gas wells, but may be useful in in situ leach mining projects as well. The process utilizes a liquid explosive that has unique safety features. The chemicals that form the explosive are subdivided into two pumpable, non- detonable components. Technology has been developed to pump these two components independently but simultaneously into the well and blend them together downhole to form the explosive. As such, surface facilities and personnel are not exposed to explosive hazards. The explosive formulations utilized in the process have been subjected to numerous safety and characterization tests and been qualified for use in deep wells with temperatures and pressures up to 250°F and 10,000 psi. The explosive composition can be varied to produce an explosive ranging, energetically, from a blasting agent to a high explosive that can be detonated after injection into a borehole, a porous media or into thin naturally occurring fractures within the roc

Jan 1, 1974

By James Douglas

The Copper Queen mine was opened in 1880 by Messrs. Martin, Ballard & Reilly, and the first copper-furnace was blown-in on August 20th of that year. Prior to that summer nothing but prospect-work had been done on the copper Queen and on a number of adjacent claims. In fact, it was a small deposit, not of copper-ore, but of cerussite, which still remains undeveloped, on the western slope of the Queen hill, which

Jan 1, 1900

By J. D. Price, G. V. Woody

MANY producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. OVERCOMING DEFECTS IN COKE FROM COLORADO COALS Colorado coking coals are all of the high-volatile type and were all laid down during he Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Pocahontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-volatile coal was developed through low-temperature carbonization-or, more correctly speaking, through the partial devolatilization-of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944