Search Documents

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

THE name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. GEOLOGY The ore deposits of Copper Mountain are related to the Copper Mountain stock, which is an ideal example of the magmatic differentiation in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanics and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial granitization of some of the volcanics. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. THEORETICAL ESTIMATE OF STOPING WITH THE DIAMOND DRILL After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping. Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1945

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By Roswell H. Johnson

The principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method. The following reasons might be advanced for the adoption oi cumulative royalties: 1. To distribute the burden in accordance with the capacity to pay. This principle is a unique one in business, although familiar in taxation. This is because it does not distribute reward in proportion to efficiency.

Jan 1, 1916

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical specifications, color demands must also be met. The firm of which I have the most knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By A. E. Moss, J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing. By 1954 iron ore will begin to move towards American blast furnaces, and shortly thereafter the annual rate of production is expected to reach 10 . million tons. To bring this vast project into being over $200,000,000 will have been spent for exploration and development, mining equipment, hydro plants, townsites, the building and the equipping of . a 360-mile railroad, and the construction of docks and ore-handling facilities. The most important iron ore deposits are located over 300 miles from tide water, see frontispiece and also Fig. 1. The frontispiece shows principal sources of iron ores and manganiferous iron ores for the U. S. and Canadian steel industry, and the major smelting districts are shaded on the map. No navi- gable rivers lead into the interior. When work was . commenced on this project there were no roads, no railroads, no communication ,system, no inhabitants, and no adequate maps either topographical or geological. The geological field season was limited to approximately 100 days per season. The obstacles facing this enterprise were many and varied. Its success will be due to the integrated team work of people of diverse skills. Explorers, Indian guides, prospectors, geologists, surveyors, mechanical, civil, electrical, and mining engineers,

Jan 1, 1954

By B. G. Klugh

In a paper before the Institute at Wilkes-Barre, Pa., June, 1911,' Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author² described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some techuical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taker] from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, slid its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sinterecl is intimately nlixed with

Jan 1, 1913

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

By A. R. Kaufman, P. Gordon

THE large-scale manufacture and use of uranium in conjunction with the atomic energy development during the war led to a need for knowing the equilibrium diagrams of uranium with various other metals. The alloys of uranium with aluminum and with iron were among the first that were studied for this purpose. Much of the work was done in the manner of a survey since it was necessary to determine the important features of the phase diagrams rather than to obtain completely detailed results. For this reason no attempt was made to locate exactly such features as liquidus lines, solid solubility limits and compound and eutectic compositions. It is believed, however, that there are no great inaccuracies in the diagrams reported here and that no important points were overlooked. Earlier work on alloys of uranium with aluminum and iron is almost nonexistent and in each case is considered to have been of little value by M. Hansen. It is interesting to note, however, that the compound UAl3 was first reported in 1902 by L. Guillet. Experimental Procedure Materials: The uranium used for making most of the aluminum alloys was obtained from material prepared by Metal Hydrides, Inc., and melted in vacuum at M.I.T. Because of the lack of an adequate supply of metal, it was necessary to use material from several different batches and hence it is impossible to state an exact analysis. However, a few results indicated about 0.01 to 0.03 pct iron and probably about 0.03 to 0.05 pct carbon. Toward the end of the work a small amount of metal was obtained from Brown University and from Iowa State College and this was used in determining the transformations in pure metal and in some dilute alloys. All of the aluminum used in this investigation came from a supply of high purity metal (greater than 99.9 pct aluminum) which was obtained through the courtesy of Dr. Mehl of the Carnegie Institute of Technology. The uranium used for making the alloys with iron was produced by the bomb reduction process which has been described by J. Chipman.² This metal, after vacuum melting, contained about 99.9 pct uranium by weight with carbon and iron as the chief impurities. Electrolytic iron containing about 0.012 pct carbon, 0.020 pct nickel and 0.009 pct copper was used in making the melts. Melting Equipment: The melting of the alloys went through a stage of development which culminated in the use of beryllia or beryllia-lined crucibles and in the use of high frequency heating in either vacuum or in an atmosphere of argon. It was found that uranium at a few hundred degrees above its melting point would pick up aluminum and to a lesser extent silicon from an alundum thimble while aluminum above 1000°C would extract silicon from the impure alundum. No reaction of either metal with beryllia was noted at temperatures as high as 1800°C. The distillation of aluminum from the aluminum-rich alloys was quite troublesome at temperatures above about 1300°C and was only partially avoided by the use of argon instead of vacuum. Melting in resistance furnaces,

Jan 1, 1951

By W. P. Sykes

In connection with a study of tungsten steels, Honda and Murakamil reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. Materials The iron powder used in preparing the alloys was obtained as follows : Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000" C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 per cent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon. The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly for several days at temperatures up to 1500' C. and for shorter periods

Jan 1, 1926

By Joseph W. Roe

MaNY questions arising in the work of the mining engineer may be solved quickly and with suffcient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of " innocuous desuctude " may lie in the uifortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer's attenti011 in terms of' every-day use they may prove of practical hearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in ally way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To Find the Strike. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It mill be assumed for the present that the rein is a plane.

Jan 1, 1911

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann' indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.'- "articular attention has been given to

Jan 1, 1958

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By Allan J. Clark

It is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper1 read before the Institution of .Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders. In the same way, as attesting the usual balance of such variations of different ores, it may be noted that the needle-like fibers of hornblende (cummingtonite), interlacing throughout the mass, render the ore more difficult to crush than would be anticipated, but on the other hand assist

Jan 1, 1916

By Fred W. Gordon

Apart from the character of pig-iron to be manufactured, other than that it shall be well reduced and open-grained, the selection of the materials should be such as to produce it at the lowest cost. As a rule, the sources of fuels and limestones are not so extensively varied as those of the ores. Many Eastern furnaces are now using Lake Superior ores, and but recently a part of the supply came from foreign ports. It is, however, of the highest importance that the character of fuels and limestones, as well as ores, should be carefully considered in determining their value and making judicious selection among those available. The formulas here offered are based upon the assumption that the heat-requirements for a given mixture are measured by a constant required by the oxide of iron, added to that required for a unit of slag, multiplied by the weight of that slag per unit of iron. The heat-requirements for oxide of iron per unit of pig-iron made are assumed to be 2854 centigrade units. This is taken from the careful analysis of Sir Lowthian Bell, and, so far as the writer is able to determine, is very nearly correct. Dividing this by the quantity of heat that may be evolved and utilized within the furnace per unit of carbon, determines the quantity of carbon required per unit of pigiron ; and if to this be added the quantity of carbon absorbed by the pig-iron, the total requirements in carbon are determined, on the assumption that pure oxide of iron is reduced with pure carbon by the ordinary process of the blast-furnace. Calculating the quantity of slag that would be made from a given mixture of ores, smelted with a given impure fuel and fluxed with a given impure limestone, multiplying this weight of slag by the heat-requirements of its unit (taken at 1050 C. H. U.), and dividing the product by the heat-units evolved and utilized within the furnace per unit of carbon, will determine the quantity of carbon required per unit of pig-iron for the slag.

Jan 1, 1893

By Thomas Wilson

IN a single-crystal cube of iron the arrangement of the atoms is that characteristic of iron at room temperature: the body-centered cubic lattice. X-ray investigation has shown this structure to be characteristic of iron, as it has shown the atomic arrangement of other metals to be characteristic of those metals also. Rarely do substances have more than one characteristic atomic arrangement. Many physical properties of metals are directly connected with their atomic arrangements, so that changes of arrangements produce changes of properties. Only chemical change influences atomic arrangement. If a difference in the physical properties of a metal is caused by a process which involves no chemical change, the cause of the difference in properties must be sought elsewhere than in the atomic arrangement. Frequently this cause can be traced to alteration of crystal orientation. The orientation of a crystal may be defined as the relationship which the crystallographic axes bear to some quantity of reference. A cube of iron appears cubic whether it is regarded from a face, an edge, or a corner. Yet these three positions represent three different orientations of the cube with respect to the observer. It is evident that the orientation of this cube of iron, unlike the atomic arrangement, is not characteristic of iron but is entirely dependent on the previous history of the cube. Most of the processes of metal working, such as wire-drawing, rolling, and bending, change the orientation of the crystals present in the worked metals. These processes usually tend to produce rotation of the crystals into positions approaching a mean. Specimens of metals show-ing this characteristic are said to possess a preferred, orientation. Tensile strength, ductility, and many other properties are influenced by orientation changes; therefore two specimens of the same metal may show different values of these quantities. In metal specimens possessing a narrowly limited preferred orientation, these quantities will vary in magnitude in different directions throughout the specimens. The investigation of the influence of manufacturing operations upon crystal orientation, and hence upon physical properties of metals, is an important

Jan 1, 1929

By C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble copper from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976