Search Documents

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By Oliver Bowles

AMONG mining men as well as in the popular mind the conviction has held sway that mining is pre-eminently a western industry. True it is that gold, silver, copper and other metals have made the States of California, Colorado, Montana, Utah. Nevada and Arizona famous. The prominence attained by these States as mineral producers is, however, not measured alone by the money value of the products of their mines. While the metals are without doubt indispensable in industry, the glamour of the precious metals, and the lure of copper, lead and zinc have given to their ore deposits a sentimental interest that often quite out-weighs their commercial importance. Today a great group of more commonplace minerals are finding a place in commerce and industry rivaling that of the metals, but there is little sentiment attached to them, and,. therefore, they attain relatively little publicity. This is the great group of the non-metallic minerals, exclusive of fuels and oils, including stone, sand and gravel, cement, lime, gypsum, asbestos, mica, phos-phate rock and many others. Almost unnoticed they have grown in production to almost unbelievable pro-portions. The estimated value of metal production for 1925 is given as $1,380,000,000, of the non-metals (ex-cluding fuels) $1,294,000,000. The non-metallic industries are not new, many of them date back almost to pre-historic times; but, as the greatest of them (on a tonnage basis) provides raw materials for the construction industries, it required the activities of the present age of construction to bring about their enormous development. Many of them enter manufacturing as well as con-struction. Non-metallic minerals constitute the back-bone of our great chemical industries. While construction and manufacture reach to all parts of the country their widest development has been in the great industrial centers of the eastern Seaboard and the middle West. Consequently the raw materials of mineral origin required for these great industries have attained a remarkable growth in the eastern half of the- United States. In compiling figures of mineral production for 1924, for which more complete data are available than for later years, the surprising fact is brought to light that the non-metallic mineral produc-tion alone of some of the eastern and middle-western States exceeds by a substantial margin the total min-eral production of some of the western States that have been classed as essentially mining States. Thus the non-metallic mineral production, exclusive of coal and petroleum, of the State of Ohio, was approximately $150,000,000; of Pennsylvania $175,000,000; and of New York $107,000,000. For the same year, 1924, the total mineral production of Utah was $84,357,000; of Montana $70,632,000; of Colorado $61,488,000; and of Nevada only $26,226,000. Even Minnesota, with its enormous iron ore production, reached only $107,845,-000, or a sum about equivalent to the non-metallic min-eral production of the State of New York.

Jan 8, 1927

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

(Members are urged &apos;to, send in for this column any notes of interest concerning themselves or, their fellow-members.) Members and guests who registered at Institute headquarters during the period Sept. 10 to Oct. 10, 1915: George H. Blakemore, Sydney, N. S. W. W. B. A. Dingwall, San Antonio, Tex.. H. Haege, Sydney, N. S. W. R. H. Jeffrey, London, England. C. A. Filteau, New York, N. Y. H. S. Emlaw, Spring Lake, Mich. Myron R. Walker, Cerro de Pasco, Peru. Y. T. Woo,&apos; Tientsin, China. William R. Grunow, Morenci, Ariz. A. L. DeDeken, LouVain, Belgium. E. DeGolyer, Norman, Okla. K. P. Swensen, Tokyo, Japan. William W. Elmer, Tuttletown, Cal. Charles Enzian, Wilkes-Barre, Pa. Huntington Adams, Iquique, Chile. C. F. Schnepp, Cobalt, Ont., Canada. W. Ray Cox, for several years Mineral Inspector of the General Land Office at Portland, Ore., has been appointed Professor of Mining and Metallurgy in the School of Mines, Oregon Agricultural College, Corvallis, Ore.

Jan 11, 1915

The Second Pan-American Scientific Congress will be held under the auspices of the United States Government in Washington, D. C., Dec. 27, 1915, to Jan. 8, 1916. The organization officers are John Barrett, LL. D., Director General of the Pan-American Union, Secretary General; Glen Levin Swiggett, Ph. D., Assistant Secretary General; the headquarters of the Congress are the Pan-American Union, Washington, D. C. The program of the Congress is divided into nine main Sections, which are given below with the name of the Chairman of each Section: 1. Anthropology, William H. Holmes, B. S., Smithsonian Institution, Washington. 2. Astronomy, Meteorology, and Seismology, Robert S. Woodward, Ph. D., Carnegie Institution, Washington, D. C. 3. Conservation of National Resources, Agriculture, Irrigation and Forestry, George M. Rommel, B. S., Bureau of Animal Industry, Department of Agriculture, Washington, D. C. 4. Education, P. P. Claxton, LL. D., Bureau of Education, Washington, D. C.

Jan 12, 1915

Page McGREGOR, A. G.-Features of the New Copper Smelting Plants in Arizona. Discussed by L. D. Ricketts, E. P. Mathewson 2145 HOWARD, L. O.-The Basic-Lined Converter in the Southwest. Discussed by Walter Douglas, E. P. Mathewson, Kuno Doerr 2145 SAMUEL, J. MOORE-Determination of Dust Losses at the Copper Queen Reduction Works. Discussed by Walter Douglas, E. P. Mathewson, S. J. Jennings, C. E. Arnold, A. G. McGregor, L. D. Ricketts 2148 MORSE, H. W., AND TOBELMANN, H. A.-Leaching Tests at New Cornelia. Discussed by H. W. Morse, Lawrence Addicks, G. D. Van Arsdale, S. J. Jennings, F. S. Schimerka, C. G. Grabill, F. N. Flynn, Stuart Croasdale 2151 LAIST, FREDERICK, AND ALDRICH, HAROLD W.-The 2,000-Ton Leaching Plant at Anaconda. Discussed by F. N. Flynn, E. P. Mathewson 2159 ADDICKS, LAWRENCE-Possibilities in the Wet. Treatment of Copper Concentrates. Discussed by F. N. Flynn 2160

Jan 12, 1916

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Oct. 10 to Nov. 10, 1914: Jintaro Kojima, Ashio, Japan. E. R. Hinckley, Seoul, Korea. J. Homer Stover, Trenton, N. J. S. A. Taylor, Pittsburgh, Pa. Kirby Thomas, New York, N. Y. Lawrence Addicks, Douglas, Ariz. Keijiro Nishio, Tokyo, Japan. Noel Cunningham, Bethlehem, Pa. Alexander K. Hamilton, Chicago, Ill. E. C. Vigeon, London, England. Harold N. Lawrie, Portland, Ore. S. E. Fairchild, Jr., Philadelphia, Pa. C. Spence Thomas, Cardiff, Wales. W. C. Schmidt, Jr., New York, N. Y. Henry Tackmann, New York, N. Y. Kenneth C. Browne, New York, N. Y. Dr. David T. Day has resigned his position with the U. S. Geological Survey and opened an office at 1331 F Street, N. W., Washington, D. C., for practice as a consulting engineer.

Jan 12, 1914

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Carl Wagner

AT elevated temperatures. most metals react with oxygen, sulphur, or halogen rather rapidly, although a coherent layer of the reaction product is formed and separates the two reactants from each other. The reaction proceeds, since one of the reactants or both dissolve and diffuse across the reaction product. In many cases the rate is diffusion-controlled as is indicated by the validity of the parabolic rate law of Tammann&apos; and Pilling and Bed-worth. wott and Gurney&apos; have suggested that diffusion processes also play an important part in the case of reduction reactions. This is confirmed by observations reported below. In general, however, the rate of reduction reactions is determined not exclusively by diffusion processes. Reduction of Silver Sulphide Above 179°C silver reacts with liquid sulphur very rapidly. Since the volume of silver sulphide is much greater than that of the equivalent amount of silver, a coherent layer of silver sulphide is formed in accordance with a rule established by Pilling and Bedworth.&apos; According to Wagner&apos;,&apos;&apos; silver ions and electrons migrate from the Ag-Ag,S interface across the silver sulphide layer to the Ag,S-S interface where the following chemical reaction takes place: 2 Ag +2 e + S Ag,S If silver sulphide is reduced by means of hydrogen, the equivalent volume of the reaction product, silver, is less than that of the initial substance. Accordingly, no coherent layer of silver is formed. Instead, fine filaments of silver grow from the silver sulphide surface into the ambient gas. This phenomenon has been investigated by many authors, especially by Kohlschiitter," who has also reviewed previous literature. Kohlschiitter has interpreted the observed phenomena by migration of "silver" dissolved in silver sulphide. According to Wagner,&apos; silver ions and electrons are the migrating particles. The sequence of consecutive steps involved in the reduction of silver sulphide is shown in Fig. 1. Every- where at the silver sulphide surface, hydrogen reacts with sulphur so that excess silver ions and electrons are formed, which migrate at random until they are captured by a nucleus of metallic silver. If such a nucleus lies on the surface and material is furnished only from the base, the original nucleus is pushed outward and thus a filament grows. Removal of sulphur and formation of metallic silver may also take place at different points when silver sulphide is reduced by copper. The reaction is usually formulated as: AgL,S + 2 Cu = Cu.S + 2 Ag but the actual reaction products are silver and a solid solution of the two sulphides. Primarily, excess silver and electrons dissolved in silver sulphide are formed. After a certain degree of supersaturation has been reached, nuclei of metallic silver may form. If, however, a silver foil is in contact with the silver-sulphide phase, as is shown in Fig. 2, silver ions and electrons will migrate to the Ag,S-Ag interface where they are captured. To confirm this scheme, a composite sample, with the geometry shown in Fig. 2, was made by pressing silver sulphide tablets 0.6 cm in diam and 0.4 cm high together with a copper cylinder and a silver foil in crucibles of iron, which does not react appreciably with silver sulphide at 400°C. After heating for 3 to 7 hr at 400°C. the specimens were cut normal to the phase boundaries. It was found that the thickness of the silver foil had increased from 0.01 cm as initial value to a maximum value of 0.06 cm. In the interior of the silver sulphide tablets only traces of metallic silver were observed. These observations show clearly that silver ions and electrons may migrate over distances of several millimeters before they form metallic silver. Reduction of Cuprous Sulphide by Iron The behavior of cuprous sulphide is very similar to that of silver sulphide, since the lattices of the high temperature modifications are identical, but in Cu.S there is a variable deficit rather than an excess of metal. To investigate the displacement of copper by iron, cuprous sulphide powder covered by a copper foil was pressed in iron crucibles and heated up to 800 °C for 3 to 7 hr. The thickness of the copper foil increased from an initial value of 0.005 cm to a nlaximum value of 0.029 cm. In the interior of the

Jan 1, 1953

Reginald S. Dean (Manganese Extraction by Carbamate Solutions and the Chemistry of New Manganese-Ammonia Complexes, P. 55) was born in Rolla, Mo. and attended the Missouri School of Mines. Mr. Dean has worked as metallurgist with Western Electric Co. from 1920 to 1929 and with U. S. Bureau of Mines from 1929 to 1946 as chief metallurgist and assistant director, and has been a metallurgical consultant in Washington, D. C. since 1946. An AIME member, Mr. Dean has presented at least 50 papers before the society. Mr. Dean is a member of American Society of Metals, American Chemical Society and Electrochemical Society. C. O. Dale (Illinois Operations of the Eagle Picher Mining and Smelting Co., co-author with W. J. Rundel, P. 72) was born in Twin Bridges, Mont. and attended Montana School of Mines and received his B.S. in mining engineering in 1944. Mr. Dale was with U. S. Navy Air Corps. as an electronics technician and worked as an engineer with C. O. Dale & Sons, Anaconda Copper Mining Co. and with Eagle Picher Mining & Smelting Co. At present he is Wisconsin manager of Eagle Picher Mining & Smelting Co. The application of machinery to mining is of special interest to Mr. Dale. A member of AIME, Mr. Dale is on the Room and Pillar or Stope and Pillar Committee of Mining Subdivision for 1951 to 1952. Mr. Dale is a member of Montana Society of Engineers and Lions Club. Golfing, fishing and wood working are his hobbies.

Jan 1, 1952

By W. Spencer Hutchinson

THE purpose of this account is to introduce to other engineers and geologists who use photography a means of interpreting topographic and geologic structure with the stereoscope. Anyone who finds this of sufficient interest to read it at all must cut out the pictures shown and have a good look at them through the stereoscope; there is no other way to appreciate what is meant. Most of us have been disappointed by the flatness of mountain pictures and by the lack of perspective in photographs taken to illustrate topographic and geo- logic features. The use of the stereoscopic principle was suggested by the work of the photographic division of the Air service during the war. Photographs of the battle line, taken from air planes, were mounted for stereoscopic study, with most remarkable development of topography, penetration of camouflage and, by the matching of pictures with a time interval between, sure revelation of new work by the enemy. Thus, two views taken from a plane flying at 10,000 ft., both of the same terrain but from different points, are mounted in proper relation and put into the stereoscope. If the distance between the two positions of the camera was 200 ft., the observer then sees the topographic and military features as though his eyes were 200ft. instead of 235 in. apart.. The result is startling in its revelation of features that are flat and unintelligible when viewed by the unaided eye or in a single photograph. The technic of the work, as developed during the war, was quite complex and

Jan 1, 1921

By Richard L. Gordon, Charles J. Johnson

Electric power demand doubles about every ten years, and because of the associated burgeoning fuel requirements, power stations absorb over half of the coal output in the United States. Throughout the 1960&apos;s, demand for coal utilized to generate electricity grew at an average annual rate of 6.5% but coal producers held back greater expansion because they expected nuclear plants to proliferate faster than they actually did. Even so, the growth rate is expected to continue at the 1960&apos;s rate until at least 1976. The continuation of the 6.5% growth rate beyond 1976, however, will require additional orders for coal-fired plants during the early 1970&apos;s. In fact, plants consuming a total of 130 million tons of coal must be ordered in the next few years. If the requisite plants materialize, total 1980 coal output for electrical power generation will be approximately 600 million tons.

Jan 1, 1971

By D. L. Rainey, E. R. Goter, W. R. Hudspeth

THE area in which spodumene-bearing pegmatites occur extends from Gaffney, S. C., in a northerly direction to Lincolnton, N. C., a distance of about 16 miles. The zone averages 2 miles in width. Interest in this area was first aroused by the discovery of small amounts of cassiterite in the pegmatites and in greissen which occurs on the walls of some of the pegmatites. Attempts were made from 1880 into the 1920&apos;s to mine and concentrate cassiterite, but there were no successful operations. In 1935 L. M. Williams became interested in the area and began prospecting by trenching and sinking several small shafts. He gradually gained control of a considerable acreage south of the city of Kings Mountain, N. C. Mr. Williams states that he produced some ore from a shaft which he shipped to the Maywood Chemical Co. in the late 1930&apos;s. In 1937 G. H. Chambers of the Foote Mineral Co. visited the area and examined several properties, but the lithium market was too small to support the necessary concentrating plant.

Jan 9, 1953

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By August J. Breitenstein, W. Spencer Hutchinson

The outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations are shown for the years 1900, 1930 and 1950 in Table 1. Method or Preparation and Interpretation of Statistical Data The fuels comprised in this study are: (1) the coal group including both bituminous and anthracite coal; (2) the petroleum group, taking in not only petroleum but natural gas and natural-gas gasoline. Natural gas for many years has been used in localities relatively near the wells but statistics were found no earlier than 1910. Demand has rapidly

Jan 1, 1934

By F. W. McNair

WITHIN the last twenty-five or thirty years the actual operations of the great mining industry have passed almost wholly under the charge of men trained in the technical colleges. It follows that the industry is profoundly influenced for good or ill by the character of the training which the college graduate receives, and the relations existing between the industry and the colleges. This fact seems to be generally recognized, as evidenced, for example, by the existence of a Committee on Technical Education created some two or three years ago by the Mining and Metallurgical Society of America. In 1921 this committee rendered a very able and. extremely well poised reports of technical education as applied to the prospective mining engineer. It deserves the attention of every one interested in the effectiveness of engineering training. That the importance of the relation between the mining industry and the engineering colleges is recog-nized is evidenced also by the mass of criticism, usually adverse, which is proffered to and often hurled at the colleges by those in the industry. The man inn the field sometimes goes so far as to say that engineering educa-tion is hopelessly inefficient and its product worthless, while the college worker sometimes complains that the demands of the industrialist are too numerous and conflicting to be met, and adds that they would&apos; best be ignored. Between these extremes, there seems to be a general consensus of opinion that the training of the would-be engineer can be, and. ought to be, made much better than it now is.

Jan 4, 1923

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor-including metal, mineral, and fuel technicians-to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world&apos;s less extensively explored areas. During the war and afterward, the task of supplying the nation&apos;s mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support.

Jan 11, 1958

E. K. Landis, Philadelphia, Pa. (communication to the Secretary) : Mr. Firmstone&apos;s paper is of great interest; but he has unfortunately otnitted to state the most important point, viz., the percentage of sulphur in the two materials he compares; and this omission vitiates the conclusions which he draws. Comparing by grade, instead of silicon-contents (as in his Table III.), the iron made using limestone with that made using dolomite, we find for gray-forge the average of four analyses under limestone to be, Si, 0.644; S, 0.089 ; while one analysis under dolomite gives Si, 0.508 ; S, 0.070. For No. 2 iron, the limestone flux gives, as an average of 19 analyses, Si, 1.107; S, 0.051; while the average of 4 analyses made with dolomite flux gives Si, 0.630; S, 0.056. It will be observed, that no No. 1 pig is given under limestone, while 14 analyses appear under dolomite, averaging Si, 0.950 ; S, 0.028. As nothing is said about changed conditions, it is Fair to presume that the ore and fuel, as well as the blast-temperature (which is stated to have been uniform at about 750&apos; F.) remained practically the same; and since the sulphur in the two fluxes is not given, it is impossible to know whether the lower sulphur for equal silicon-contents is due to the use of dolomite or to other conditions. The use of dolomite would produce a more fusible cinder, and the furnace would be hotter than when using limestone; therefore, we might expect to see a grayer iron. The amount of So. 1 iron made with dolomite seems to confirm this supposition; and, under these conditions, we might expect more of the sulphur to be volatilized, and to pass off in the gases. The easier fusibility of the cinder would also permit more rapid driving; and this should reduce the amount of silicon and sulphur in the iron, as the amount of reduced metalloids in the pig is directly proportional to the length of time it remains in the reducing-zone.

Jan 1, 1895