Search Documents

By Hiroshi Oikawa, R. G. Blake, A. G. Guy

An equatzon has been derivedfor conveniently calculatzng the couvse of homogenzzation in a three-corviDonent solid solutiorz. The necessary assumptions are that the initial distributions of concentration are sinusoidal and that the four interdiffusion coefficients are constant. Employed in the deriuation were the Laplace transform and the fouter Fourier sine transfovwz. The final equation is shown to be in good agveetnent with the experimental results of Kirkaldyet al. on Cu-Sn-Zn alloys. COMMON boundary conditions for representing physical problems are those of the finite solid and of the infinite solid. Many metallurgical phenomena, however, have the geometrical form of a finite pattern reproduced throughout an infinite solid. Precipitation within a uniform matrix and segregation during solidification are examples. The purpose of this treatment is to show that a convenient and useful mathematical analysis is possible in those cases in which the finite pattern can be approximated by a sine function. The particular topic to be considered here is the elimination of segregation by diffusion, but the mathematical model has applicability in many other areas. It should be recalled that the mathematical solution of a typical problem involving a finite solid, such as diffusion into a thin layer, is quite involved.' Various types of solutions are used depending on the degree of advancement of the diffusion process and on the initial conditions. A step function is the simplest initial condition, but even in this case the general solution has the form of an infinite series. Kirkaldy et a1.2 have

Jan 1, 1968

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during January: A. Neustaedter, Jersey City, N. J. William Jones, Kent, England. A. J. Sweetser, Boston, Mass. Percy E. Barbour, Candor, N. C. Algernon Del Mar, Los Angeles, Cal. Herbert S. Kohlberg, El Paso, Texas. W. B. Cogswell, Syracuse, N. Y. I. N. Knapp, Ardmore, Pa. R. E. Chambers, New Glasgow, N. S.

Jan 2, 1914

Iowa State College Ames, Iowa Iowa State Mining Society CARL S. NELSON, President NORMAN S. GEIST, Secretary K. A. PHILLIPS, Faculty Sponsor C. G. DRESSER, Counselor University Of Kansas Lawrence, Kansas University of Kansas Student Chapter of A.I.M.E. WALTER CROOK, President EDWARD C. MISHOU, Secretary E. A. STEPHENSON, Faculty Sponsor GEORGE M. FOWLER, Counselor K. A. SPENCER, Counselor .

Jan 1, 1942

By James Paul

BEGINNING in December, 1933, and continuing to the close of April, 1934, large sums of money were expended in the states of Pennsylvania, Ohio and West Virginia through the conduct of Federal and State Civil Works Administration, financed by the Government as a part of the President's recovery program to furnish employment to mine employees idle as a result of the economic depression. PURPOSE OF THE PROJECT The protection of the public health against the pollution of public water supply by acid mine drainage was the incentive that prompted the request that the sealing of abandoned bituminous coal mines be made a Federal project. A paper before the Central Section of the American Water Works Association, Wheeling, W. Va., on Aug. 24, by E. S. Tisdale, Chief Engineer of the West Virginia Department of Health, tersely says: In October, 1933, the combined experience of the U. S. Bureau of Mines and the U. S. Public Health Service and the States of Pennsylvania, Ohio, West Virginia and Kentucky resulted in a report being filed in Washington, first with the Public Works Administration and later with the Civil Works Administration, where it was favorably acted upon, calling for these governmental agencies under the direction of the U. S. Public Health Service to expend $1,500,000 in a unified effort to seal abandoned coal mines in Pennsylvania, Ohio, West Virginia, Kentucky and six other states farther down along the Ohio river. The report referred to was embodied in a petition that was signed by the chief engineers of the State Departments of Health of the several states contiguous to the drainage area of the Ohio River. The project as established under Federal supervision became interstate with respect to the several states involved, and upon the termination of the Federal project on Feb. 15, it was authorized as a State C.W.A. project, effective Feb. 20, under the supervision of the State Departments of Health and the State C.W.A. Administration, which continued to March 29, and was succeeded by the S.E.R.B. of the R.W.D. from April 2 to April

Jan 1, 1935

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.' Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts' Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg's method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965

By Gregory Comstock

THERE is a growing interest in the possibilities presented by the manipulation of metal powders, which justifies an attempt to summarize their character and potential value. A summary of this kind presents an opportunity for making a classification of metal powder products into several general types. Our present knowledge of the finer and more abstract aspects of many of the principles involved in metal powder technique is extremely limited. Any conclusions as to the ultimate value of the process will, therefore, for the present at least, be of doubtful value unless they are substantiated by its products. The number of such products is increas-ing. A study of their diverse and unusual characteristics; an examination of the methods by which they ale made, and a consideration of the reactions that take place during their fabrication, in so far as we can define them, should afford as good an evaluation of this interesting development as it is possible to make at this time. A critical study of this kind results in a formidable list of special attributes, which apparently are characteristic of applied powder metal-lurgy. A comparison of these special effects with the end products and well defined limitations of the melting and casting process indicate that often they may very well be considered as being special advantages. They are subject, of course, to certain not as yet so well defined limita-tions of their own. Based on current products only, a necessarily con-densed summary of the more striking special attributes of the metal powder process follows.

Jan 1, 1938

By Cleland N. Conwell

APPLICATION of seismic methods to the location of buried channels in placer mining is fairly common knowledge, yet some of the facets of seismic refraction surveys have remained obscure in their application to mining. This description by a member of the U. S. Bureau of Reclamation team investigating bedrock at the Oso Dam site, may offer a lead to wider application of the method for bedrock determinations in engineering of mine and mill plants, tailing disposal, and water supply. It may also offer assistance in planning geological exploration in areas covered by overburden. Pertinent, and perhaps more than passingly significant, is that the seismic survey of the Oso dam site started at noon and was completed the afternoon of the next day. Location Oso dam site is on the Navajo River, Archuleta, County, Colo., 30 miles southeast of Pagosa Springs, Colo., 10 miles northwest of Chama, N. M. Bedrock at the proposed dam site is Mesa Verde Formation, Cretaceous age sandstone. The nearest good sandstone exposure is about 5/8 of a mile upstream from the location of the seismic determinations. The material above bedrock is sand and gravel with sandy loam soil covering benches above the river. The site appeared favorable, after a geologic and topographic reconnaissance, but overburden thickness was unknown. Exploratory drilling was not contemplated in the near future so a short seismic investigation was selected as the most suitable method of determining depth to bedrock. Field Procedure Geophysically, a seismic depth investigation is simply the measurement of depth from ground surface to the top of a layer which transmits seismic waves at a higher velocity. In this case the high-velocity seismic layer tentatively correlates with the Mesa Verde sandstone. Field procedure required a seismic explorationline or "spread" with 12 geophones set at measured intervals. Explosive charges were buried at few feet in the ground and detonated at shotpoints near the ends of the spread, and at intermediate points. The time of travel of the seismic waves from the shotpoints through the ground to each of the geophones along the spread was measured and recorded photographically with equipment housed in a field truck. The seismograph on each spread provided a time-travel graph. From it were computed the speed of seismic waves in various layers below the surface and depth to each different seismic layer below the shotpoint. In the case of the Oso dam site it was possible, in addition, to determine the depths below certain geophones, because there were only two seismic layers involved. Interpretation In seismic exploration waves are refracted from the top of layers which often correspond to divisions between subsurface formations. When drill holes are available the geologic logs offer a means of correlating stratigraphic breaks with seismic layers, improving reliability of seismic interpretation in terms of depth to bedrock or other geologic terms. There were no drill holes available in the case of the work at the Oso dam site. Geologic conditions appeared favorable for seismic technique because of excellent contrast in seismic wave velocity between the overburden and the Mesa Verde formation. The upper layer had a velocity of approximately 2500 fps and was interpreted as overburden, the lower layer had a velocity of approximately 9000 fps and was assumed to be the sandstone. These velocities are of the order expected in these materials. The seismographs obtained at the Oso dam site were excellent. The energy from the shot came in strongly at each geophone, giving an easily read record. Time-travel graphs plotted from wave arrival times were uniform and made interpretation comparatively easy. In Spreads 1 and 2 near the river the lower velocity layer was 12 to 15 ft deep. For the spreads on higher ground, or the bench south of the river, it was from 15 to 29 ft deep.

Jan 1, 1952

By Frank Firmstone

It is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

1. What Is a Rock Burst? . . . . 569 Jack Spalding . . 569 A. F. Robertson . 569 W. R. Crane . 569 G. S. Rice......569 P. J. Shenon........... 569 L. C. Graton........... 569 2. What Are the Causes of Rock Bursts? 573 Jack Spalding..........573 A. B. Yates and P. J. Shenon 574, 578, 592, 596 A. F. Robertson . . . . . 575, 595 W. R. Crane. ... 579 G. S. Rice.........582 Oscar Weiss .........582 P. B. Bucky..........582 P. H. Bird.....588, 592, 593, 595 M. K. Hubbert.........593 G. Wheeler.......... .593 B. F. Tillson........593, 595 T. T. Read............594 3. How Can Rock Bursts Be Prevented?. 597 Jack Spalding..........597 A. B. Yates and P. J. Shenon ... 598 A. F. Robertson.......599 W. R. Crane....... .602 G. S. Rice............602 Page 4. How Can Rock Bursts Be Predicted?. 602 Jack Spalding.........602 A. F. Robertson.......602, 603 A. B. Yates and P. J. Shenon ... 602 W. R. Crane......602 G. S. Rice......602 B. F. Tillson...........603 5. How Can Rock Bursts Be Controlled? 603 Jack Spalding..........603 A. F. Robertson.......603 W. R. Crane...........604 A. B. Yates and P. J. Shenon 604 Oscar Weiss........605 G. S. Rice......- 604, 609 R.D.Hoffman..609, 610 R. D. Hall..........609 R. H. Cromwell . . 609 P. J. Shenon...........609 P. B. Bucky......609, 611 B. F. Tillson.........609, 611 A. B. Yates...610, 611 P. H. Bird.......610 6. General Discussion........ 611 Jack Spalding.......... 611 R. D. Parker....... . 616 C. Baring Horwood........ 618 P. B. Bucky........... 619 Foreword This symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge, which, if successfully met and overcome,

Jan 1, 1946

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By Ronald J. McGregor, Anton R. Hendriksz

INTRODUCTION The NIMCIX contactor was developed in the late sixties at the National Institute for Metallurgy in South Africa, for the main purpose of extracting uraniuy from relatively low-grade uranium solutions. ' The concept was sufficiently developed by 1974 to permit the operation of a 1500 litre per minute column to treat unclarified urgnium-bearing solution under industrial conditions. The plant operated so successfully that several large-scale units have subsequent18 teen constructed and are operating efficiently. ' Total resin consumption figures as210w as 3 per cent per annum have been reported, and the extraction efficiencies of the installations have been exceptionally good. All the solutions treated have been acidic in nature and in every case have been of such a nature as to significantly depress the maximum uranium loading on the resin beads. The chemical constituents of the leach solution fed to the loading column determines the ease with which the soluble uranium can be absorbed by an ion exchange resin. The concentration of competing ions and various resin foulants define the nature of the continuous ion exchange equipment required for efficient extraction performance. The basic NIMCIX concept is retained in these various alternate designs, but batch or continuous elution methods with fully automated or manual control systems may be selected for the different process solution conditions. BRIEF DESCRIPTION OF THE NIMCIX CONTACTOR The NIMCIX ion exchange column is a multi-stage fluidized bed contactor which is designed to permit a counter-current flow of solution and resin in order to maximize extraction efficiency. The flow o resin is periodic, based on the Cloete and Streat 5 principle of reverse flow. The basic operating cycle can be divided into five periods, as illustrated in Figure 1. For the purposes of describing the cycle, the loading column is considered; how- ever, a similar sequence may be applied to the operation of a NIMCIX continuous elution column. S'I'EP 1: During the forward flow period, Solution flows up through the column and fluidizes the resin contained in each stage. The uranium depleted solution overflows the upper flared-section of the column as the tail solution. Step 2: The flow of solution to the column is temporarily stopped and the resin is allowed to Settle onto the plates in the column. STEP 3: During the reverse flow period, a fixed volume of solution is drained from the column to the transfer vessel. This flow causes resin transfer to occur from stage to stage and also out of the bottom stage. At the end of this period, which expires when the low level switch (LS) is actuated, some of the resin is left in the conical section of the column and the pipe interconnecting the column and the vessel. STEP 4: The cone flush period ensures that all the resin left in the cone of the column and the pipe is transferred to the transfer vessel before forward flow commences. STEP 5: The loaded resin in the transfer vessel, which has been isolated from the column, can either be hydraulically transferred to the top of the elution column or eluted in the vessel before being transferred to the top of the loading column. The major advantages associated with the NIMCIX concept are: (i) Simple method of operation (ii) Contactor can readily be scaled up to large diameters. (iii) Because the resin does not pass through pumps or airlifts, and valves cannot be closed on resin beads at any time, the resin losses are exceptionally low. (iv) Operating costs are low. (v) Relatively few valves in the system. (vi) Stable operation is achieved over a wide range of feed rates and concentrations.

Jan 1, 1980

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,' shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,' shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication' did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

By Charles Catlett

Probably no one has had occasion to examine an undeveloped coal property without hearing some hopeful or interested party insist that the bed will improve when opened some distance under cover. When the bed is already in good condition, the opinion is usually advanced that the same character may be expected, at least to the bounds of the hopeful individual's holdings. My attention has been called in this way to the extent to which a bed is affected by its outcrop at the surface ; and having had opportunity to examine a number of openings immediately at the surface, and also a short distance under cover, I submit some observations bearing on this question. Whatever may have been the original variations, we may assume that coal-basins presented in comparatively modern times approximately parallel beds interstratified with fire-clay, slate, sandstone, etc., as represented by Fig. 1. Under the effect of erosion, Fig. 2 would be formed. It is obvious that along the line A, B, C, in Fig. 1, the beds exist under conditions differing from those at A', B', C', or again at A", B", C", in Fig. 2, in their exposures to atmospheric agencies, pressure and erosion. The effect of the first is to decompose and soften many of the strata; of the second, when presented unequally, to cause the movement of such material as was at all plastic towards the point of least pressure ; and of the third, to remove the strata in whole or in part. It

Jan 1, 1901

By S. P. Sharples

Having occasion a few weeks ago to investigate the subject of black band iron ore in West Virginia, I was surprised at being met at the outset with a denial of its existence. One gentleman went. so far as to offer one hundred dollars an acre for any land in West Virginia that contained a seam or vein of even a single foot in thickness, and when shown the ore he acknowledged that it was genuine, but declared it had been imported. That black band does occur in West Virginia is to-day well known to a number of persons. There is a seam on the Gauley River of about a foot in thickness of good ore, which I understand Mr. Lewis and others are making preparations to work. The great trouble with black band ores as heretofore found in this country has been their limited extent. At Fort Washington, for instance, they had a very fine show ing of ore, but it soon gave out. It has also been asserted that the black band ores of the Western Coal Measures were worthless in the furnace, and Fort Washington has been pointed out as an example of the fate of any one who should undertake to work them. But they have been successfully worked at Youngstown and in other parts of' Ohio, and I am assured by old furnace-men from Ohio that there is not the slightest difficulty in. working them if properly managed. The deposits to which I wish to call the attention of the Institute,

Jan 1, 1882

By S. P. Sharples

HAVING occasion a few weeks ago to investigate the subject of black band iron ore in West Virginia, I was surprised at being met at the outset with a denial of its existence. One gentleman went so far as to offer one hundred dollars an acre for any land in West Virginia that contained a seam or vein of even a single foot in thickness, and when shown the ore he acknowledged that it was genuine, but declared it had been imported. That black band does occur in West Virginia is to-day well known to a number of persons. There is a seam on the Gauley River of about a foot in thickness of good ore, which I understand Mr. Lewis and others are making preparations to work. The great trouble with black band ores as heretofore found in this country has been their limited extent. At Fort Washington, for instance, they had a very fine show ing of ore, but it soon gave out. It has also been asserted that the black band ores of the Western Coal Measures were worthless in the furnace, and Fort Washington has been pointed out as an example of the fate of any one who should undertake to work them. But they have been successfully worked at Youngstown and in other parts of Ohio, and I am assured by old furnace-men from Ohio that there is not the slightest difficulty it working them if properly managed. The deposits to which I wish to call the attention of the Institute,

Jan 1, 1882

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li2O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication' did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949