Search Documents

By R. M. Bird

Few persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry-sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co. A few years ago the so-called Albany sands were dug by simple methods and hauled by horsecart to railroad. Depletion of sand near railroad sidings and extended use of automotive power have appreciably extended the area from which sand is now being dug. It is not unusual to haul 5 miles to the railroad. As stripping is quite shallow, 6 to 18 in., and the banks of usable sand generally run from 12 in. to 4 ft., it is economical to work the bank by benches so narrow that the overburden can be thrown by hand shovel to the exposed bottoms. In effect the top soil goes back to where it was, but on a lower level. Consequently the general surface appearance of a mined acreage is the same as before. This condition is in fact cutomarily required when a farm owner sells his sand in the ground. After such replacement, in the course of 3 to 5 years the soil is no less fertile than it was before mining. The sand itself varies as to grain and bond vertically and also along the breast. No mechanical equipment has been developed to compete with hand shovels and no machine has as yet been devised that grades the sand as required. Uniformity of sand, as shipped, depends first, last and all the time on the man on the job. Mixing equipment can change the appearance of the sand and mask its lack of uniformity, but it will never correct wrongly graded sand, dug from the bank. Modern methods of testing are helpful in setting up standards against which the man in the bank can compare his sands, but a good bank foreman is the only assurance that the sand, as dug, matches the required sample.

Jan 1, 1926

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions prevail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes. CLASSIFICATION OF MOISTURE Moisture in coal can be classified as inherent and surface moisture. Inherent moisture is regarded as a part of the true coal substance, having been present in the original vegetal matter from which coal was

Jan 1, 1943

L. D. Ricketts, New York, N. Y.-In recent years the metallurgical field of the copper industry has expanded greatly, the copper ores have become lean and diverse in character, and we are obliged to treat such ores on a very large scale. On the commercial side, the operating and consulting staffs of ,the great mining companies have been enlarged and organized, and no great capital expenditure is decided upon until it has been investigated and recommended by a highly organized force of specialists as a committee. I believe that in the scientific field and in the most valuable proceedings of our various societies the old idea of one-man point of view and one-man treatment of principle and detail together has been. splendidly developed and should continue, but for the advancement of our art we should deliberately discuss subjects among ourselves in order to do away with the idiosyncrasies of the individual and to gain a composite view representing the best thought of many men. In the development of new ideas leading to the introduction of new methods, the societies could enlarge their present great field of usefulness if such discussion be had, and in my opinion further great good could be done if a number of men of different qualifications and experience would join in preparing a joint book, each dealing with his particular problem, but consulting the other men. In this way individualism would be preserved and various processes would be described, and if properly reviewed the paper would be palpably capable of analysis, and the student would have at his command the associated efforts of a group of qualified engineers.

Jan 4, 1915

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By George W. Bain

The good work of the surveys supported by the different branches of the government needs little mention to geologists but is underappreciated by people at large. Geologists and engineers realize their usefulness and yet even from this group one hears occasionally an undercurrent of discontent about their work or the distribution of it. The very fact that discontent arises within and without this group and has drawn attention of legislative bodies of the country in the present time of stress means that a large number of people do not receive or do not realize that they receive benefit from these public works. This seems to be a clear indication that more than the relations between government surveys and the mining industry is involved and that if the mining industry is interested in continuation of the work of these surveys on the past scale they must consider the other survey divisions and their activity. Also, relations between government surveys and certain specialized types of mining have not been as close as they should be. I have been employed in almost the entire range of fields offered to geologists and have studied closely the feeling of people towards geological service. Recently it has been a pleasure to be closely associated with men who were as deeply interested in civic welfare and affairs of state as in the financial success of a large industry developing natural resources. Previously I had seen service in a national survey, a state survey, summer employment by a large mining company exploring new property and detailed geological work for a large corporation. Major responsibility as a college instructor has left me free to view each of these assignments in unprejudiced fashion and at the same time study the relation of government surveys to large natural resource industries, average industrial and construction work and service to nongeologists and laymen. Considerations Governing Geologic Public Service Three groups of people must be satisfied by the surveys if dissatisfaction is to be dispelled. First there is a large group of people who pay taxes to support the government activities and must receive some service

Jan 1, 1935

By George W. Bain

The good work of the surveys supported by the different branches of the government needs little mention to geologists but is underappreciated by people at large. Geologists and engineers realize their usefulness and yet even from this group one hears occasionally an undercurrent of discontent about their work or the distribution of it. The very fact that discontent arises within and without this group and has drawn attention of legislative bodies of the country in the present time of stress means that a large number of people do not receive or do not realize that they receive benefit from these public works. This seems to be a clear indication that more than the relations between government surveys and the mining industry is involved and that if the mining industry is interested in continuation of the work of these surveys on the past scale they must consider the other survey divisions and their activity. Also, relations between government surveys and certain specialized types of mining have not been as close as they should be. I have been employed in almost the entire range of fields offered to geologists and have studied closely the feeling of people towards geological service. Recently it has been a pleasure to be closely associated with men who were as deeply interested in civic welfare and affairs of state as in the financial success of a large industry developing natural resources. Previously I had seen service in a national survey, a state survey, summer employment by a large mining company exploring new property and detailed geological work for a large corporation. Major responsibility as a college instructor has left me free to view each of these assignments in unprejudiced fashion and at the same time study the relation of government surveys to large natural resource industries, average industrial and construction work and service to nongeologists and laymen. Considerations Governing Geologic Public Service Three groups of people must be satisfied by the surveys if dissatisfaction is to be dispelled. First there is a large group of people who pay taxes to support the government activities and must receive some service

Jan 1, 1935

By G. K. Manning, A. R. Elsea, A. B. Westerman

A considerable number of high-tem-perature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. .4t the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in vitalliurn after various heat treatments. Howcver, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chro-mium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja and Guertler2 indicated that cobalt and chro-mium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to 85 pct chromium undergo a transformation at [zoo to 12 50 c More recently, Wever and Haschimoto,3 Wever andLange,4and Matsunaga5 carried Out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallogra~hic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Mat-SUnaRa. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these excep-tions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data arid the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitalhum by deter-mining the diagram for the cobalt-chro-mi~m system- Experimental Work For the convenience Of the reader, the diagram as determined by the present investigation is presented in Fig 3. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the melting point for pure chromium is the

Jan 1, 1949

By T. V. Moore, H. D. Wilde

In many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas-lift has been published by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken, slippage must be determined empirically. This paper presents the results of some work carried on to measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is more efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves arc of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By J. E. 214-000-000-010 Warren, M. R. J. Wyllie, T. Meidav, L. Scharon, R. Uhley, A. J. deWitte

By considering the stoichiometry of the underground combustion process, an equrztion was derived relating the point velocity of the combustion front as a function of the air flux, fuel content, efficiency' of oxygen uitilization, hydrogen:carbon ratio, and ratio of carbon dioxide In carbon monoxide produced. In addition, an equation for cnlcrllating the amount of injected air necessary 10 produce the oil from I Cu. ft of reservoir space was derived. This equation has a direct bearing on evaluating compression costs for the process. Values calculated from these equations are in good agreement with experimentnlly obscrvcd values obtained from laborator) tube runs reported in the literature. The equations are also u\eful for atlcrlyzinf: experinlental data for inconsistencie.r.. I NTRODUCTION The injection of energy in the form of heat into an oil-bearing formation as a means of increasing the recovery of oil has been the subject of much discussion and experimentation as far back as 1920. The ideas have ranged from the injection of steam to the direct use of electricity as a means of getting thermal energy into a formation. However, most laboratory and field studies have been confined to the process whereby a portion of the crude in the reservoir is burned to generate the necessary heat to increase the mobility of the oil by reducing its viscosity. A recent paper by W. L. Martin, et al.', described the results of a number of laboratory experiments in which the combustion process was studied in a sandpack. Studies such as this indicate that with the temperatures involved, the oil is partially coked in this process and it is this coke which provides the fuel for combustion. The combustion of this residual coke can be analyzed theoretically by applying simple stoich-iometric principles to the combustion process. It is the purpose of this paper to compare the results reported in these experiments with those obtained from theoretical considerations. The variables studied by Martin, et al, among others, include combustion front velocity, air flux, oxygen utilization, fuel concentration, ratio of carbon dioxide and carbon monoxide in combustion gases, and the hydrogen:carbon ratio of the residual fuel. All these variables come into consideration when the stoichiometry of the combustion process is studied. The experimental conditions and results are tabulated in Tables 3 and 4 of Ref. 1. For purposes of comparison with calculated results, it was necessary to change the units of a number of the variables. UNDERGROUND COMBUSTION STOICHIOMETRY The combustion or oxidation of the carbonaceous residue or "coke" on the sand can be described in terms of the equation: where n is atomic ratio of hydrogen to carbon, m is ratio of moles of CO2 to CO produced, and CH. is taken as the unit molecular weight, realizing that actually the coke has a large range of high molecular weights. Assuming that all the fuel laid down in the sand is burned, the ratio of moles of oxygen consumed to moles of coke can be written as follows. Moles 0MolesMolescoke In terms of moles O2 per pound of coke, where 12 + n is the molecular weight in pounds per mole. If the 0, consumed is measured in standard cubic feet (60°F and 1 atm) and the coke in pounds per cubic foot of formation, 2, then:

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

I BELIEVE that my work would surely be host a seed without fit and that I would fail in that cause which disposed me to satisfy your request to write and form this work [75] if while laboring on it I did not tell you of the art of casting, since it is a necessary means to very many ends. I realize even more that I must tell as much as seems necessary since I have already demonstrated the methods of recognizing the natures and locations of the metals, of smelting and reducing them to their ultimate perfection, and finally have taught you to make their associations and alloys. It is especially necessary since this art and work is not well known, so that no one can practice it who is not, so to speak, born to it, or who does not have much talent and good judgment. For this reason and also because it is closely related to sculpture, whose arms are the support of its life, it is very highly esteemed. In order to describe the whole art in every part, I say that the greatest labors of both mind and body are required for its operations in the beginning, middle, and end. It is indeed true that these labors are endured with pleasure because they are associated with a certain expectation of novelty, produced by the greatness of art and awaited with desire, particularly since the artificer sees that it is an art pleasing and delightful even to ignorant men. As a result, as if ensnared, he is often unable to leave the place of work. To conclude: The outcome of this art is dependent upon and subject to many operations which, if they are not all carried out with great care and diligence and well observed throughout, convert the whole into nothing, and the result becomes like its name [cast away]. Therefore, having considered this work many times, with its extraordinary obstacles and the bodily labors heavy as a stevedore's, instead of exalting it with praise, I wish to say that it is such that a man of noble birth, even though he be gifted or be drawn to it by pleasure, should not practice it and could not unless he is accustomed to the sweat and many discomforts which it brings. He must suffer the great natural heats of summer as well as those excessive and continuous ones from the enormous

Jan 1, 1942

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of' these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By J. C. Wilhoit, E. M. Galle

A three-dimensional photoelastic study was made to determine the stress state around the wall and bottom of a wellbore due to fluid pressure within the wellbore and unequal principal geostatic stresses. Models simulating the wellbore were made from a phthalic anhydride-cured epoxy resin. The frozen stress technique of three-dimensional photoelastic-ity was used to determine the stresses within the model. Two separate problems were solved: (1) hydrostatic pressure on all sides of the model with the exception of the inside of the hole, and (2) uniaxial compression perpendicular to the center line of the hole. The results are presented in the form of contour curves for each stress component. The curves cover a region which extends several hole radii from the bottom and wall of the hole. By proper use of these results, the state of stress may be calculated for any point on the wall or bottom of the hole, as well as for any point within the material that surrounds the hole. A systematic method is given for calculating these stress components for any combination of fluid pressure within the wellbore and system of unequal principal geostatic stresses, provided one of the principal geostatic stresses is parallel with the wellbore. The results show that stresses around the wall and bottom of a wellbore, induced by an uneyual system of principal geostatic stresses, are appreciably different from those induced by geostatic stresses that are hydrostatic. For uneyual principal geostatic stresses, the experimentally determined stresses on the wall of the hole several radii from the bottom are in good agreement with the stresses calculated by elastic theory. INTRODUCTION Interest in the problem of determining the stresses around and near the bottom of a wellbore, due to geostatic loading and fluid pressure within the wellbore, originated in the petroleum industry. The stresses on the wall of the wellbore are of interest due to their relation to lost circulation during drilling, the fracturing of formations during squeeze cementing and hydraulic fracturing of producing formations. The stresses on the bottom of the hole are of interest to the drilling segment of the industry because to produce a hole in the earth it is necessary to remove material from the bottom of the hole. This removal of material is produced by structural failure of the rock, whatever the criterion for failure may be. Cunningham and Eeninkl have shown that for certain conditions the effect on drilling rate of the bottom-hole stresses caused by a hydrostatic overburden pressure is small compared to other effects. This question, however, needs further experimental and analytical investigation. Much information concerning the stresses on the walls of wellbores has been published considering both equal and unequal principal geostatic stresses. The problem of determining the stresses around the bottom of the wellbore is considerably more complicated. However, previous investigators have obtained numerical and experimental solutions to the problem for equal principal geostatic stresses. whitworth2 and woods3 have obtained numerical solutions. word415 obtained a three-dimensional photoelastic solution, Durelli and Deily 6 obtained surface stresses only by photoelastic means, and Cheatham and Wilhoit7 determined the stresses around the bottom of a short cylindrical cavity. While Miles and McGuire, Harrison and Kieschnick and Hubbert and Willis 10 obtained the stresses on the wall of a wellbore for unequal principal geostatic stresses, they did not concern themselves with the stresses near the bottom of the hole. The estimates made by Hubbert and Willis of the differences between the principal geostatic stresses indicate that, to obtain a satisfactory solution for the stresses around the bottom of a wellbore, unequal principal geostatic stresses should be considered. This work is directed toward obtaining such a solution. The materials in the earth's crust are nonhomo-geneous, permeable and anisotropic. Previous

By A. C. Richardson

TROUGHS or launders are probably the oldest machines used for ore. concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean: coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four troughs placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratifica-tion. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and. fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder.

Jan 1, 1938

By H. L. Hartman

The estimation of the magnitude of pressure changes which occur in mine ventilation circuits is of primary importance to the mining engineer in making changes in an existing mine or in projecting the ventilation requirements of a new mine. It is a formidable task in many cases, because no adequate theory is available and empirical data are unreliable or even lacking. The common practice of increasing one's estimate of the mine static pressure by an arbitrary "safety factor" to compensate for the unknown is a poor substitute for accuracy. Generally little difficulty is encountered in calculating friction losses in mine airways. As long as the friction factor can be reliably estimated, the well-known Atkinson formula gives accurate results. However, it is in the determination of shock losses that the ventilation engineer encounters difficulty and is apt to resort to an arbitrary allowance. Shock losses may constitute as little as five or as much as twenty-five percent or more of the overall pressure drop in the mine, and such allowances are generally completely unsatisfactory. Since other shock losses have been covered by McElroy (1), this paper deals with a long-neglected source of shock and pressure change in ventilation circuits, divergence and convergence of airflows, here referred to by their more common mining terms, splits and junctions. PREVIOUS WORK There is practically no fundamental information available in ventilation literature on the splitting and junction of airflows, either in mining or mechanical engineering periodicals or handbooks. Fluid mechanics textbooks seemingly avoid the subject of divergence and convergence, except for brief empirical treatment. The only investigation reported for mine ventilation systems was by Weeks, et a1 (21), in 1933. Although applicable to the case of line brattices in coal mines, it cannot be applied to the general case of mine splitting and junctions involving change of direction with little or no area change. In dealing briefly with the subject of shock losses at splits and junctions, McElroy (1) suggests only that they be considered comparable to bends, with losses at junctions being increased 50 pct to allow for interference of merging streams. He recognizes the importance of quantity ratio but concludes that exact quantitative data are lacking to compute losses at splits and junctions. A very capable summary and analysis of the state of knowledge in industrial ventilation and fluid mechanics regarding losses due to divergence has recently been reported by Gilman (3). In considering all earlier work dealing with both air and water as fluids, he compares results on a common basis and obtains good empirical agreement. For divergent flow, the controlling variable in each branch is the quantity ratio, although the deflection angle is of secondary importance. Empirical equations are presented for straight and 90-deg branches with varying velocity ratios, assuming branches smaller than the main duct. These formulas are modifications of the Borda equation for abrupt contraction and expansion. The only information available on shock losses in convergent flow are approximate experimental data presented by Alden (4) and the Manual of Recommended Practice for Industrial Ventilation of the American Conference of Governmental Industrial Hygienists. Alden considers the effects of both quantity ratio and deflection angle. The data indicate an effect opposite to that observed in divergence, the shock loss varying directly with quantity ratio. SHOCK LOSS THEORY Because pressure losses due to shock have been found to bear a constant relation to the mean velocity of flow in a given conduit, they are frequently expressed as a dimensionless function of the velocity head, termed the shock loss factor. For airflow in ducts and mine airways, the shock loss may be represented by the formula (1): Hx - XHv, (1)

Jan 1, 1961