Search Documents

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By AIME

HAPPILY, a large group of the non-ferrous fraternity have long valued a personal association with the new Chairman of the Institute of Metals Division. Many others who will meet him, either officially or unofficially this year, will find themselves sharing the enthusiasm with which he has been welcomed to his new office. Albert A. Smith, Jr., was born at Butler, N. J., on Dec. 28, 1904, and moved to New Haven in time to initiate his preparation for Yale University on the home grounds. After receiving a B.S. degree cum laude in 1926, he stayed on for graduate work at the Hammond Laboratory under C. H. Mathewson, and was awarded an M.S. degree in 1928.

Jan 1, 1948

By S. S. Raymond, C. R. Hayward

In reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment be carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired temperature throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treatment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-know tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels which, after tempering for periods varying from 15 min. to 2 hr., show no very great bifferences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 1, 1917

Discussion of the paper of M. B. YUNG, presented at the Pittsburgh meeting; October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2451 to 2458. T. T. READ, New York, N. Y.-I might .point out that this paper of Mr. Yung&apos;s is on a field that is comparatively little known. It is not as well known as the Kochiu tin field, of Yunnan, which is probably the third . in tin output of the world. This field under discussion is considerably further west and the tin which is produced here is, according to Mr. Yung, of somewhat higher grade than the Yunnan tin, and is used by the refiners at Hong Kong to improve the grade of the Yunnan tin. Most of you know that the tin from the Yunnan is shipped to Hong Kong, where it is refined and shipped to Europe. Mr. Yung points out that the Fu Chuan deposits are entirely alluvial and not found in any veins. They .differ in that from the Kochiu deposits, which Leclere says are "nullement alluvionels; leur origéne filonienne est de plus evidentes." Granite is the country rock here; doubtless the tin occurred in veins in the granite, and the deposits have resulted from the disintegration of the granite. This is a country of strong erosive agencies. The country is semi-tropical, and the rainfall is heavy, so that one would naturally expect deep surface erosion of this kind.

Jan 4, 1915

Executive Joseph L Gillson, Chairman, J W Woomer, Vice-Chatrman, John S Bell, Walter R Hibbard, Jr. R R McNaughton Finance John P Hammond, Chairman, James C Gray, J S Smart, Jr Investments Gall F Moulton, &apos;63, Chairman, Andrew Fletcher, &apos;62, John M Lovejoy, &apos;61, George I Brigden, ex off as AIME Treasurer, John P Hammond, ex off as Chairman, AIME Finance Committee Award Committees Grouped together at end of list Cooperation with the Canadian Institute of Mining and Metallurgy and the Mining Society of Nova Scotia R R McNaughton, Chairman, C Gerow, Sherwin Kelly

Jan 1, 1960

By T. M. Chance

THE term "low-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as 1 ½ per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low sulfur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, With few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 ½ per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous dis-tricts, it has been necessary to turn to the areas of higher-sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.-Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout

Jan 8, 1919

By Frank C. Roberts

Neglecting the hydrogen and hydrocarbons, 1 will assume the following analysis as a fair average composition, by weight, of the waste gases escaping from a coke-burning blast-furnace: CO2............17.25 CO,............25.25 N,.............57.50 100.00 The 25.25 CO requires for combustion 62.6 of air, or 11.398 of oxygen, necessitating the passage of 48.202 nitrogen into the products of combustion. The latter, therefore, have the following composition: CO2,,............ 56.9 N,............105.7 Tile total specific heats of these quantities of the respective gases are 12.31 and 25.79, giving for the combined product, 38.1 approximately. That is, the product of combustion will absorb 38.1

Jan 1, 1889

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.&apos; Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to &apos;85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

Robert Carl Sticht, member of the Institute since 1886, an American metallurgist of world-wide reputation, died in St. Margaret&apos;s Hospital, Launceston, Tasmania, on April 30, 1922, after an illness of eleven months, against which he fought with the highest courage and characteristic fortitude. The news of his passing came as a great shock to a host of his friends and former associates here, but on account of his long absence from the United States, exact biographical details have been heretofore lacking. Throughout Tasmania, the expressions of public sorrow were many and impressive, and the flags were flown at half-mast in Queenstown, Zeehan, and the entire Mt. Lyell district, in honor of the man who had won his place in the community as a great captain of industry and a man universally admired and loved. Sticht had been connected with the Mt. Lyell Mining & Railway Co. in Tasmania throughout its entire productive period. He had originally been induced to go to Tasmania through the good offices of the late Dr. E. D. Peters, then professor of metallurgy at Harvard University, who after personally examining the undeveloped Mt. Lyell properties, recommended Sticht as the best possible man to work out the complex metallurgical problem which that great orebody presented. Sticht had already made himself the leading authority on pyritic smelting, having taken up the idea as suggested and partly worked out by Lawrence Austin and carried it through to a certain degree of perfection in the case of limited tonnages of special ores. After studying the situation at Mt. Lyell, Sticht found the conditions there to be almost ideal for pyritic smelting, and he had the courage to adopt as the basis for a permanent, and eventually successful, solution of the metallurgical problem, a process that was then little more than a theoretically interesting possibility. The thorough studies and remarkable results attained at Mt. Lyell were published as chapters in Doctor Peters&apos; various publications on the metallurgy of copper, Doctor Peters giving full credit to Sticht for their authorship. These chapters by Sticht practically constitute the: best literature of the art of pyritic smelting. The accuracy of observation,

Jan 1, 1923

Robert Carl Sticht, member of the Institute since 1886, an American metallurgist of world-wide reputation, died in St. Margaret&apos;s Hospital, Launceston, Tasmania, on April 30, 1922, after an illness of eleven months, against which he fought with the highest courage and characteristic fortitude. The news of his passing came as a great shock to a host of his friends and former associates here, but on account of his long absence from the United States, exact biographical details have been heretofore lacking. Throughout Tasmania, the expressions of public sorrow were many and impressive, and the flags were flown at half-mast in Queenstown, Zeehan, and the entire Mt. Lyell district, in honor of the man who had won his place in the community as a great captain of industry and a man universally admired and loved. Sticht had been connected with the Mt. Lyell Mining & Railway Co. in Tasmania throughout its entire productive period. He had originally been induced to go to Tasmania through the good offices of the late Dr. E. D. Peters, then professor of metallurgy at Harvard University, who after personally examining the undeveloped Mt. Lyell properties, recommended Sticht as the best possible man to work out the complex metallurgical problem which that great orebody presented. Sticht had already made himself the leading authority on pyritic smelting, having taken up the idea as suggested and partly worked out by Lawrence Austin and carried it through to a certain degree of perfection in the case of limited tonnages of special ores. After studying the situation at Mt. Lyell, Sticht found the conditions there to be almost ideal for pyritic smelting, and he had the courage to adopt as the basis for a permanent, and eventually successful, solution of the metallurgical problem, a process that was then little more than a theoretically interesting possibility. The thorough studies and remarkable results attained at Mt. Lyell were published as chapters in Doctor Peters&apos; various publications on the metallurgy of copper, Doctor Peters giving full credit to Sticht for their authorship. These chapters by Sticht practically constitute the: best literature of the art of pyritic smelting. The accuracy of observation,

Jan 1, 1923

By Dr. O’Neil Thomas J., Donald W. Gentry

"Who is the man who views the mines and promptly turns them down? Who is the one that thinks this is the short cut to renown? Who is it gives the bum advice to the innocent financier? The knowledge-feigning, theory- straining mining engineer." -Anonymous INTRODUCTION Taxes levied against mining properties and operations are a critical cost in the economic evaluation of mining investments. Indeed, taxes represent a substantial cost of doing business in the minerals industry and often have a significant impact on corporate investment decisions. A good example was the postponement of mineral development in the state of Wisconsin, primarily because of what was perceived to be excessive taxes imposed by that state. In many respects mining investments are no different from other industrial investments. Astute taxing authorities should recognize that geologic endowment is a necessary but clearly not a sufficient condition for mineral investments. The fact that a mineral deposit exists does not necessarily mean that it will ultimately be developed-a point that many taxing authorities fail to recognize. While it is true that ore deposits are not mobile in the sense that they cannot be physically moved to a district having more favorable taxes, corporate investment capital certainly is mobile and flows to ventures which maximize wealth to the firm. In short, higher taxes reduce project yields and tend to drive investment capital elsewhere. The appropriate type and level of taxation imposed upon the mining industry continues to be a very controversial and emotion-charged topic. Mining activities have been taxed at various levels over the years due to widely differing taxation philosophies. Location has also influenced taxation policies, as evidenced by the diversity of tax laws and assessment procedures applied to mineral deposits by the various states. Indeed, mineral taxation varies from state to state, from county to county, and from one mineral commodity to another. Whether or not a given tax is appropriate for a specific mineral deposit, or even an industry, is a difficult problem to assess. First, the type or kind of tax which should be imposed must be considered. Second, it is most important to define a fair and unambiguous base against which to levy the tax. Finally, one must consider the tax rate to be applied to this base. It is the combination of these two components

Jan 1, 1984

By H. H. Stoek

Mine models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them haw been lost, or have been stored away in some mining company&apos;s office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 1, 1918

By AIME

The following corrections (in italics and bold face) were received too late for the September issue of Transactions: Page 270, Abstract, line 1, spelling should be goethite. Page 270, column 1, authors&apos; box, authors&apos; affiliations should read: L. A. BAKER, formerly Principal Research Scientist, is Pellet Plant Superintendent, Cliffs Western Australian Mining, Cape Lambert, W. A., Australia. C. G. THOMAS is Experimental Officer, Minerals Research Laboratories, C.S.I.R.O., North Ryde, N.S.W., Australia. R. J. CORNELIUS and K. S. LYNCH are General Superintendent, Product and Process Development, and Superintendent, Pellet Plant, respectively, Hamersley Iron Pty. Ltd., Dampier, W. A., Australia. G. J. ARMSTRONG, formerly Chief Metallurgist, Hamersley Iron Pty. Ltd., is Mill Superintendent, Samin Ltd., Burra, S. A., Australia. Page 271, column 2, line 41, should read "highest possible spalling temperature and to adjust the. . :&apos; Page 275, column 1, line 1, should read "(LOI) figures are shown in Table 1 and vary from 2.61..." Page 275, column 1, line 16, spelling should be goethite. Page 276, column 2, line 6, should read "Predicting Grate Speed and Production Rate: The cor-..." Page 276, column 2, line 8, should read "basis of Blends A, B, C, D, and Plant Ore 1, shown in Table..." Page 276, Table 3, heading under "Prediction Method" should read Blend E. Page 277, column 1, line 38, should read "=293 tph of specification pellets (see Table 1 for loss-..." Page 277, column 2, replace caption for Fig. 14 with the following: Fig. 14-Example of calculation of hood temperature profile during downdraft free-water drying, given plant free-water drying time. Page 277, column 2, replace caption for Fig. 15 with the following: Fig. 15-Example of calculation of hood temperature profile during drying, given plant goethite drying time.

Jan 1, 1974

(The paper by L. H. De Wald-Tech. Pub. No. 429 was presented at the Boston meeting, September, 1931.) W. A. SCHEUCH, Chicago, Ill.-Since starting up our Hawthorne copper wire plant we have found that wire bars from certain suppliers perform quite differently from those of other suppliers. In attempting to evaluate these bars, we made cross-sections, and in making these cross-sections we found considerable variation in the crystal structure. Indications were that there was some preference in the type of crystal structure. In attempting to find the reason for that we discussed it with the various producers and-also reviewed the literature. Mr. DeWald was assigned to determine the various factors that enter into copper wire bar crystal structure, on the basis that the product was a horizontally cast wire bar of practically identical composition and of recognized good composition for the present quality product sold in the market. Mr. DeWald has asked me to say that he should have made reference to Mr. Dalzell&apos;s paper on a theory concerning gases in refined copper. D. K. CRAMPTON, Marion, Conn. (written discussion).-Mr. DeWald has set forth an interesting and thorough exposition of the factors controlling macrostructure of this material. It is particularly interesting to us as it somewhat parallels work we have done on macrostructure of round copper billets for piercing into tubes. Our findings as to the effect of the several variables on macrostructure check Mr. DeWald&apos;s. The general principles underlying the two are precisely the same. The fact that we worked with copper deoxidized with phosphorous instead of tough-pitch copper, and round billets cast on end instead of wire bars, does not influence the results. We have found that round billets cast so as to produce large radial grains have greater soundness and density than those with a fine macrostructure. Further, and more important, we have found that the billets with large radial grains show markedly different performance on piercing from those having a fine equiaxed structure. With a given temperature of billet and adjustment of piercing machine, the coarse-grained material requires appreciably lower power for piercing and goes through the operation inn appreciably less time. These two differences are of sufficient commercial importance to warrant exercise of great care in maintaining the coarse structure. It seems probable that much the same phenomenon should hold in the hot rolling of tough-pitch wire bars. We would expect that, other things being equal, the coarse-grained wire bars would roll more readily and require less power than fine-grained ones. Moreover, we believe the differences in initial structure of the wire bars should be largely eliminated in the hot rolling process and during the subsequent drawing and annealing, of wire would be entirely eradicated.

Jan 1, 1932

By Charles Pack

DIE castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into threee groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. CASTING MACHINES The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly. apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings.

Jan 2, 1919

By J. R. Campbell

In order to discuss the subject intelligently, it will be necessary to touch briefly on the forms in which sulphur is supposed to exist in coking coal to be carbonized in beehive or byproduct ovens. Sulphur is known to exist in coal as sulphides and sulphates, as can be determined experimentally. Then there is the so-called organic sulphur, i.e., sulphur in combination with the carbon, &apos;hydrogen, and oxygen of the coal, about which much has been written, but nothing definitely proven in an experimental way. In fact, so far. as we know, there never has been developed a satisfactory and conclusive method in the laboratory for the direct determination of organic sulphur. For most coking coals, it can be safely assumed that the preponderance of sulphur is in the form of pyrite (FeSz). When exposed to comparatively low temperatures during the coking process, it loses its sulphur according to the following chemical reaction: 7FeS2 = Fe7Ss + 6S. It will be seen, therefore, that six out of the 14 atoms of sulphur (or 42.8 per cent.) are expelled, or volatilized. FelSa remains in the coke as pyrrhotite, or magnetic sulphide of iron; this accounts for the highly magnetic properties of the powdered coke. A more commonly accepted reaction is FeS2 = FeS f S, in which the straight sulphide of iron is produced with 50 per cent. volatilization of sulphur. In the beehive methods of coke making, air is introduced in sufficient amounts to carry on the distilling and the coking processes, and the sulphur is oxidized along with the other volatile products: First, into sulphur dioxide (SO2), known by the pungent andsuffocating odoremitted from the trunnel head; second, into sulphuric anhydride (SOa); and, finally, into sulphuric acid, as it comes into contact with the air and moisture. In a properly regulated draft on a beehive oven, there is never complete combustion of the gases. In other words, the coking process should be carried on in a reducing atmosphere, and a low-grade producer gas kept issuing from the trunnel head. For coals of about 30 per cent. volatile matter, the ratio of air to gas is 3½ to 1. In complete combustion, the ratio is 6 to 1, producing an extremely high temperature

Jan 1, 1916

By Frederick M. Becket

DoctoR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering&apos; this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur&apos;s prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanicd. Several of the previous lecturers had the good fortune to attend the classes of Professor Howc and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe&apos;s book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world&apos;s pioneers in metallography, I was curious a few days ago to learn the nature of Howe&apos;s early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe&apos;s ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and scienees. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By Frederick M. Becket

DoctoR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering&apos; this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur&apos;s prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanicd. Several of the previous lecturers had the good fortune to attend the classes of Professor Howc and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe&apos;s book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world&apos;s pioneers in metallography, I was curious a few days ago to learn the nature of Howe&apos;s early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe&apos;s ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and scienees. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By R. W. Raymond

The death of Mr. Stetefeldt, which occurred at Oakland, Cal., March 17, 1896, was a surprise, as well as a sorrow, to many of his friends and professional colleagues. In the Engineering and Mining Journal of March 28th, I published an obituary article, the substance of which, modified and enlarged by later information, forms the basis of the present biographical notice. I am indebted to Mr. Albert Arents, Alameda, Cal., and Mr. 0. H. Hahn, Monterey, Mex., life-long friends, and to Miss Pauline Anacker, of Gotha, Germany, a cousin of the deceased, for details which I could not have obtained elsewhere. Carl August Stetefeldt was born September 28, 1838, in the village of Holzhausen, in the duchy of Gotha, Germany, where his father was a Lutheran pastor. He was an only son, and (after the early death of a sister) an only child. In his boyhood he is reported to have been physically delicate, but mentally precocious. In 1847 his father was transferred to Hörselgau, near Waltershausen, where, besides discharging his pastoral duties, he kept a select private boarding-school, in which a few pupils received a training preliminary to the " gymnasial" course. Among these pupils (one of whom was the now famous Dr. Knorr, the discoverer of antipyrine) he included his own son, who, thus carefully prepared, entered in 1852, at the age of fourteen, the gymnasium at Gotha. The records of the gymnasium bear witness that his conduct in and out of school was " blameless," and his attention to study good." But his career as a "gymnasiast" was marked by an act of rebellion probably more startling then than it would be now. Being much more strongly attracted by the natural sciences than by the dead languages, he conceived a special aversion to Hebrew, and engaged in a conflict with the professor in that department, out of which he seems to have come victorious. At all events, he was not obliged to pursue further

Jan 1, 1897