Search Documents

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations. Geology Composition and Morphology Diatomaceous silica qualifies as a. mineral of organic origin in much the same way that aragonite and collophane do. The silica of the fossilized diatom skeleton closely resembles opal or hydrous silica in composition (SiO2 • nH2O) .4, 12, 203 The silica is of acute biological significance, not only for the cell wall component, but also for the basic life process.45, 51 Without silica, cell development ceases .31 In addition to bound water, varying between 3.5 and 8%, the siliceous skeleton may also contain, in solid solution, or as part of the Si02 complex, small amounts of associated inorganic components-alumina, principally-and lesser amounts of iron, 46, 49, 55 alkaline earths, alkali metals, and other minor constituents.59, 63, 67 Boron is reported to be an essential element for diatom growth .52, 58 Since diatomaceous silica is not pure hydrous silica but contains other intimately associated elements, there is good reason to consider it a distinct type or variety.4 Associated with the diatomaceous silica, and integrated as part of the diatomite, may be variable amounts of organic matter, soluble salts, and particles of rock-forming minerals that were syngenetically deposited or precipitated with the diatom frustules. Sand, clay, carbonate, and volcanic ash are typical common contaminants. Other contaminating minerals may be present, such as feldspar, mica, amphiboles, pyroxenes, rutile, zircon-the result of weathering, then transporting, and subsequent redeposition of surrounding land masses. Commercial diatomite may also contain fragments and particles of

Jan 1, 1983

By Molly Gleiser

The standard free energies of formation of some gaseous metal oxides together with those of their condensed oxides have been plotted against temperature. The heats of formation of the gaseozcs oxides are tabulated. An explanation is given of the use of the data to predict the importance of the gaseous metal oxides at high tenzperatures. RECENT mass spectrometric work1 has resulted in the detection of several hitherto unknown gaseous oxides and the measurement of their free energies of formation. Of especial interest is the fact that several of the refractories in common use either as crucibles or furnace tubes, and metals used in Knudsen cells and in furnace windings, have been found to have one or more stable gaseous oxides. In view of the present emphasis on high-temperature techniques, the development of vacuum metallurgy.z heating by electron bombardment and plasma jets, and the resultant shift to ever higher temperatures, it is no longer possible to plan experiments without taking into consideration the significance of the presence of these gases in the system, the reactions they undergo. and their contribution to the vapor pressure. A good example of what went wrong in earlier work, when the existence of these gaseous molecules was not yet known, is presented by the work of Hoch, Nakata, and Johnston. Hoch and coworkers attempted to measure the vapor pressure of solid ZrO2 by letting the vapor in equilibrium with zir-conia effuse from a tantalum Knudsen cell. The free energies of formation of solid zirconia and tantala are such that a short calculation showed that the reaction

Jan 1, 1962

By J. P. Boisseau, C. N. J. Wagner, E. N. Aqua

An analysis ulas made of powder-paltern peaks from cold-rolled polycrystalline copper and from copper powders, compacted into briquets (1 in. diameter) with pressures up to about 106 psi. Powder-pattern peaks from both contact faces were measured with a diffractometer and CuKa radiation. Laltice-parameter measurements indicate the presence of residual stresses in the bulk specimen of the order of a - -10 kg per sq mm after 93 pct reduction in thickness, and give some evidence for the occurrence of deformation stacking faults (probability a - 0.003) in both bulk and powder samples. Fourier analyses of the line profiles were carried out on the (111) - (222) and (200) - (400) Pairs of reflections. The particle sizes decrease rapidly with increasing deformation and reach asymptotic values of De (111) = 550A and D, (200) = 350A at about 25 pct reduction in thickness or 80,000 psi pressure for compaction. The anisotropy of the particle sizes indicates the presence of microtwins and stacking faults on (111) planes. The rms strains increase also with deformation and reach limiting values of 2 x 10-3 in the [100] direction and 1 x 10-3 in the [Ill] direction at a distance L = 100A normal to the reflecting planes. THE diffraction of X-rays in cold-worked, polycrystalline, fcc metals and alloys yields Debye-Scherrer patterns in which the individual (hkl) lines may show a broadening, a shift, and an asymmetric shape.' These effects can be explained by the fragmentation of the small, coherently diffracting domains, the presence of residual elastic strains in the lattice, and the formation of stacking faults. X-ray studies of stacking faults in fcc metals and alloys have been methodically performed during the last few years, but so far most of the investigators dealt with cold-worked powder specimens obtained by filing.2-8,10-19 In such specimens, the crystals are randomly oriented and the average elastic strains are assumed to be zero, so that the observed peak shifts are due to stacking faults only. The agreement between X-ray diffraction theory1,20 and experiment is generally good. On the contrary, cold-worked, polycrystalline bulk specimens (after wire drawing, rolling, plastic deformation by tension or compression, etc.) contain residual elastic strains, which may not average to zero in the surface of the specimen and show very strong preferred orientation of certain lattice planes (texture) parallel to the specimen surface. Nonzero elastic strains also produce peak shifts, the magnitudes of which depend upon the crystallographic orientation of the reflecting lattice planes in elastically anisotropic materials as well as on the type of plastic deformation and which have to be taken into account when measuring stacking-fault probabilities in deformed bulk specimens.21-23 The purpose of the present investigations was to perform a detailed X-ray analysis on a bulk specimen of a fcc metal deformed by rolling at room temperature and on powder of the same material deformed by compaction, and to compare these results with those previously obtained on cold-worked filings.18 Pure copper was chosen for this study since it is known to produce only a small quantity of stacking faults by filing at room temperature.3,16,17,19 The residual elastic strain in the surface of the bulk copper should be the predominant factor determining

Jan 1, 1965

W. H. BASSETT, * Waterbury, Conn.-Manganese should not be expected to remedy all the defects that are due to poor melting practice. It is undoubtedly valuable in helping to eliminate porosity in many of the alloys. In the copper-nickel alloys, its use is becoming almost universal, for, beside helping to make sound castings, it tends to hold the carbon in solution in the solidified alloy. GWILLIAM H. CLAMER,? Philadelphia, Pa.-I have found that manganese copper is satisfactory for eliminating sulfur and that it works very well in the crucible and when you have reducing conditions; but in a large reverberatory charge, where the conditions are oxidizing, we were not able to eliminate the sulfur.

Jan 1, 1919

By Frederick T. Williams

The purpose of this paper is to discuss the relative merits of the large 31/8-in. machine and the small 2 1/4-in. tappet machine in driving development-headings; and although the data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winzing. Recently we drove two parallel cross-cuts through the same formation, using a 3 1/8-in. machine at the breast of one crosscut, and a 2 1/4-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties, the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, the air-pressure or the experience of the operating crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to "pull " the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated andesitic or pho-nolytic breccia, true massive andesite, trachytic phonolyte, tuffs, and along dikes of decomposed basalt and hard phonolyte. In every instance a satisfactory record was made. The headings here describe? mere driven through highly indurated andesitic breccia, having a hardness of from 5.2 to 7.2 and a sp. gr. of from 2.2 to 2.8. The action of the breccia under the drill was not materially different from that of ordi-

Jan 1, 1907

HAVING promised you to write concerning the nature of ores in particular, I must tell you some general facts, especially those concerning the places, kinds, and manner of their existence as well as the tools which are used. However, you must know that according to good investigators these ores are found in many parts of the world. They show themselves almost like the veins of blood in the bodies of animals, or the branches of trees spread out in different directions. Indeed, careful investigators of minerals, wishing to show by analogy how ores are located in mountains, have drawn a large tree with many branches, planted in the middle of the base of a mountain. From its principal trunk extend various branches, some thick, some slender, exactly like real trees in mature forests. They think that these grow and enlarge continually and draw themselves toward the sky, ever converting into their own nature the most disposed adjacent materials so that finally the tips arrive at the summit of the mountain and emerge with clear sign, sending forth, in place of leaves and blossoms, blue or green fumosities,* marcasites with small veins of heavy mineral, or other composition of tinctures. From these things, when they are found, it is possible to make certain inference that such a mountain contains ores, and as the signs are more or less, so are the minerals plentiful and rich or poor. For this reason the prospectors for these things take heart according to the manifestations that they find, and with hope and certainty of profit they take all possible pains to mine with skill and expense those things that the signs have indicated. Often there are ores of such a kind and quality that they raise a man in wealth to the skies. For this reason men penetrate with eyes of appraisal and judgment within the mountains and see almost exactly the places where there is ore and the

Jan 1, 1942

By C. E. Taylor, L. V. Fegan

With on-stream electrical-resistance measurement as a basis, Bethlehem Steel developed a system for the completely automatic control of moisture in the feed to pelletizing. This system was later successfully adapted to the sintering process, with automatic control of moisture serving to maintain the air permeability required for effective burnthrough. Control of moisture content is an important factor in the agglomeration processes by which iron ores are converted into either pellets or sinter for use in blast furnace burdens. In both pelletizing and sintering the iron ore feed must be mixed with the proper amount of water so that capillary attraction and surface tension forces can be utilized to cause the ore particles to coalesce and form larger agglomerates. The success or failure of the entire pelletizing or sintering process depends on maintaining the proper moisture. Therefore, continuous automatic control of moisture is one of the conditions for the automation and optimum use of both pelletizing and sintering processes. In pelletizing, variation in moisture can cause ball size to change and is a common cause of cycling which results in a fluctuating feed to induration. Excessive moisture can cause lumps to form at the cutter bar and contributes to the formation of buildup on the green pellet screens. Green pellets with excess moisture deform and reduce bed permeability. In sintering, accurate control of moisture is also important because moisture must be within the limits that give the bed the required permeability for good burnthrough. In response to these problems, a moisture meter, based on the principle of electrical resistance measurement, was developed. This moisture meter has been a key factor in the development of systems for providing uniform feed of concentrates in most of Bethlehem's pelletizing and sintering plants. The automatic moisture control system for pelletizing was successfully plant-tested and resulted in the following: (1) Control of moisture in the green pellets to +0.2%. (2) Up to 50% reduction of bentonite consumption. (3) Control of unscreened green pellets so that 85% of the furnace product at Cornwall was within the size range of -5/8 +3/8 in. (4) Improved quality of product with a tumble test of 94 and a "Q" index of 90 as the result of feeding a consistently uniform feed to a shaft furnace. In sintering, where sinter-mix temperature change and variable feed could cause errors in moisture measurement, the system was designed to maintain the correct moisture under virtually all plant operating conditions. It was successfully plant-tested and is now in use in most of Bethlehem's sintering plants. The system achieves: (1) Control of moisture within the desired limits for optimum production. (2) Continuous measurement and control of moisture even with intermittent feeding of mix, so that attention by the operator is seldom required. The two automatic control systems provide smoother startup, minimize upsets and contribute to the consistent control of process variables in pelletizing and sintering. MOISTURE-CONTROL SYSTEM FOR PELLETIZING Fig. 1 shows the general arrangement of the system for automatic control of moisture in pelletizing.1 In this system a bin level controller, using a single probe which regulates filter speed, maintains a uniform low concentrate level in the bin.' The moisture meter, comprised of an analyzer and control components, continuously measures the moisture in the bed and adds water to adjust to the desired level. The meter is placed in an open-loop (feed-forward) control, i.e., water addition occurs downstream from the probes. Filter vacuum must be set so as to produce a filtercake moisture which is below the optimum for pelletizing. Bentonite is added after the

Jan 1, 1969

By Ali M. Heidarieh Zadeh, Raghu N. Singh

The paper presents a stability investigation of shaft intersections and pit bottom roadways in the vicinity of upcast and downcast shafts at a colliery in the U.K. Aschemeof instrumentation was aimed at monitoring the strata displacement surrounding the pit bottom roadways and shaft intersections with a view to ascertaining the origin of the strata movement and effectiveness of the control measures. The bore- hole instrumentation results together with a theoretical analysis suggested that the cause of instability could be attributed to the drivage of a roadway within the shaft pillar. A semi-empirical technique was used to calculate the amount of support resistance required to reinforce the pillar to take additional abutment load. A rock bolting system was designed to provide a required increase in thrust capacity of the roadway support. The results indicated that roadway closure was effectively controlled after installation of bolts indicating efficacy of the control measures adopted.

Jan 1, 1982

By Francis N. Flynn

Many excellent papers, descriptive of the milling and smelting of every kind of commercial ores, the refining of virgin metals, the casting into various shapes demanded by the trade, the rolling into shapes best suited to the factory machinery and the making of composition alloys to suit every requirement have been issued by the many technical societies dealing with non-ferrous metals. It is a wonderful collection of papers, of which the mining and metallurgical engineers may well be proud, but strange as it may seem, metallurgists in general appear to take the stand that when they have delivered suitable alloys to the foundry and rolled products to the factory their duty to write papers has ceased, at least in so far as the A. I. M. E. is concerned. Still we read in the daily papers that the mining companies are absorbing metal-manufacturing industries. The purpose of this paper is to describe the reclaiming of non-ferrous scrap metals at manufacturing plants, taking as an example the automobile industry. Collection and Disposition of Scrap Until about five years ago, much of the factory scrap, with little or no preliminary treatment, was sold to secondary-metal smelters. Of late years the factory salvage department has become an important part, of the plant in reclaiming everything of value and incidentally does much of the work formerly done by the smelters. Like most good things, it is sometimes overdone, and much work is done at the factory with inexperienced men that could be done much better by experienced skilled labor at the custom smelting plants. Employees of the salvage department collect the waste products in all departments at the source and in that way avoid much contamination. Every reasonable precaution is taken to keep the scrap clean. It is hand-sorted, cut, burned, magnetized, concentrated, separated or compressed, as the case may be, preparatory for re-use in the plant or for selling to others.

Jan 1, 1930

By A. T. Peters

DURING an investigation concerning the use of large nozzles for pouring of low-carbon rimming steels, the practical details of which were reported elsewhere, it was noticed that increases of nozzle sizes were generally followed by improvements of slab surface quality. It is the purpose of this note to present the data available and some tentative opinions about this phenomenon. The problem of correlating pouring rates with the metallurgical performance of steels is complicated by several factors. The two most important are; 1) Variations of the steel pouring rate throughout a pour, these being due to the nozzle erosion, which enlarges the bore area, and the dropping ferrostatic pressure in the ladle. The pouring rate is lowest towards the end of a heat when the ladle is nearly empty. 2) Variations in the ingot pouring time due to the different ingot weights poured. Consequently, the use of the average pouring rate of a heat may not be exact, but in large-scale production it is not practical to treat ingots separately according to their pouring rates. The variations of ingot weights and sizes may be overcome by considering the rate of rise of steel in the mold. Hence, the average rate of filling of molds throughout the pour of a heat, inches per second, will be used in this note. Every ingot rolled at Inland is rated at the blooming mills prior to hot machine scarfing as being good, fair, or poor for cracks, scabs, and checking. The latter term refers to the network of breaks or lines associated with overheating or burning in the soaking pits. It is also known that thin-skinned steel is prone to show this defect if the subsurface blowholes are exposed during reheating or rolling. The experiences with the surface quality of slabs rolled from ingots poured at different rates are presented in Fig. 1. The data represent nearly 11,000 ingots. It appears that all three types of defects are in-

Jan 1, 1960

By H. N. Hall

Reservoir and producing characteristics can govern the decision to use either a one-, two- or three-dimensional model for making predictions for gravity-drainage reservoirs. Examples of conditions requiring one-, two- and three-dimensional calculations are given. In 1961 the author presented a method for predicting one-dimensional gravity-drainage performance. This work has been exrendcd to obtain a three-dimensional model, which is described and for which a sample problem is presented. Introduction Many papers on gravity drainage or gas-cap drive'-3 have been presented for conditions where the reservoir is treated as a single areal segment so that, in effect, only one-dimen-sional flow is considered. Other authors'-Q ave given evidence showing that the one-dimensional concept would be unsatisfactory to predict reservoir performance for certain types of reservoirs. Experience has indicated that specific reservoir and producing conditions govern whether one-, two- or three-dimensional concepts must be used as a basis for reliable reservoir performance predictioils. Previously the author presented a paper outlining a method for predicting the performance of gravity-drainage reservoirs.' That paper treated the reservoir as a single areal segment so that it was applicable for only one-dimensional flow. The work has been extended to obtain a three-dimensional model that can be used to predict performance of gravity-drainage reservoirs. Although capable of being three-dimensional, it can be used equally well for one- and two-dimensional predictions. This paper discusses those reservoir and producing conditions governing the choice of model, and also describes a three-dimensional model suitable for predicting reservoir performance in the more complex situations. Discussion The Choice of Model To predict reservoir performance, it is necessary to represent the reservoir by a physical model. A mathematical model, based on the assumed physical model, then is used to predict the movement of oil and gas within the reservoir. The word "model" is used here to connote the combination of both a physical model and a mathematical model based on the physical model. Certain types of reservoir situations may be predicted suitably with a one-dimensional model, whereas two- and three-dimensional models may be required for other situations. This section illustrates reservoir conditions associated with the use of a specific type of model. Many types of reservoir structures are such that gravity drainage possibly could be an important factor in oil production. Production practices, as well as the nature of the structure. can influence the type of model that should be used. obviously, it is impossible to discuss all combinations of reservoir structure and production practices that might be encountered in gravity-drainage reservoirs. The following are typical examples of conditions where a choice must be made among a one-, two- or three-dimensional model to predict reservoir performance satisfactorily. Conditions Requiring a One-Dimensional Model Fig. la shows contours for an asymmetrical anticline in which gravity drainage might be expected to be important. Fig. Ib depicts a cross-section along Line A-A in Fig. la. Existence of a gas cap is a good clue that gravity drainage will be an important factor in producing oil from this type of reservoir. However, it is not essential since a gas cap will form as oil is produced from the reservoir. If the proper combination of reservoir permeability and withdrawal rates is present, the reservoir will behave like a

Jan 1, 1969

By C. B. Post, G. V. Luerssen

It is generally recognized that non-metallic inclusions in steel come from two principal sources. First are the chemical reactions in the furnace, or in subsequent deoxidation, resulting in slag which does not free itself from the metal. Much information has been published concerning these chemical reactions and their control through proper attention to slag viscosity, composition of deoxidizers, and other qualities. The studies of this subject by C. H. Herty, Jr. and others through the medium of physical chemistry have yielded much information for the steelmaker. The second source is erosion of ladle refractories, such as lining brick, stoppers, nozzles and runners, causing entrapped particles of globules of fluxed silicate material. In contrast with the large amount of information available on the first source, relatively little has been published on the subject of erosion which, in the case of basic electric melted steel, is the principal source of nonmetallics. This is probably due to the fact that the problem was assumed to be one of simple mechanical erosion, which could be solved primarily by modification of ladle practices. Good improvements have been made by elimination of slurries in the ladle, better ladle and runner refractories, and more attention to pouring temperatures. It is doubtful, however, that this problem has been recognized in its true light since it is not one of simple mechanical erosion but rather one of chemical reaction between the metal and the refractories; and in this sense is as much a problem of physical chemistry as the reactions involved in the actual steelmaking process. The influence of ladle refractories on the resulting cleanness of steels was early recognized by A. McCancel who examined large inclusions in steels made by both acid and basic practices. His chemical analyses showed the large influence exerted by the manganese content of the steel on erosion of the ladle and nozzles used in those days. The presence of MnO in such inclusions led McCance to the hypothesis that both basic and acid steels react chemically with the ladle refractories so that small globules of fluxed refractories are carried in the stream into the molds. This early work of McCance was checked by one of the present authors on basic electric bearing-steel, and it was found that on steels containing as low as 0.40 pct manganese the fluxed surface of the ladle lining after delivering such a heat showed as high as 25 pct MnO by actual analysis. Furthermore, by lowering the manganese content of the steel to 0.20 pct, ladle erosion was decreased with a corresponding decrease in silicate inclusions in the steel. Limitations placed on the manganese content for the required inherent properties made it impossible to pursue this line further, and subsequent attention was concentrated on improved ladle refractories, care in keeping the ladle clean and free from loose refractories up to the time of tapping, and pouring the steel at optimum temperature. Our study of the chemical reactions at the metal-brick interface between steel and ladle refractories was revived in 1939 as a result of an experimental observation made on the cleanness of alloy steels of the SAE types. This observation showed that the relative cleanness of such steels made in basic electric arc furnaces of 12 ton capacity and poured in ingots ranging from 1100 to 2200 lb weight was determined to a large extent by the ratio of the manganese and silicon contents, provided other steelmaking variables such as tapping temperature, pouring temperature, pouring time, amount of aluminum added for grain size control, and degree of deoxidation in the furnace were kept reasonably constant. Detailed studies made on the deoxidation and slag practice during the refining period of basic electric furnace practice showed that these two variables exerted some influence on the resulting cleanness of steel in the form of bars and forgings. The important variable, the manganese-silicon balance, was not apparent until heats were made in succession by the best furnace practice kept under fairly rigid metallurgical control. Another observation pertinent to this work concerned the similarity in the microscope of slag particles causing magnaflux or step-down indications in subsequent rolled bars, and the patches of slag frequently seen on the surface of ingots. These patches are generally believed to come from the glassy metal-brick interface in the ladle and represent an entrapment of such glass (both from the ladle brick and nozzle) in the metal as it flows over the refractories in the neighborhood of the nozzle. These glassy particles are carried down into the mold with the liquid steel, and gradually coalesce into a slag "button" which floats on the surface of the steel as it rises in the molds. Periodically the button is washed to the side of the ingot where it is trapped between the surface of the ingot and the mold, later appearing as a slag patch on the surface of the ingot after stripping. Even though most of the small glassy particles coalesce into a slag button while the ingot is being poured, it is logical to suspect this step in the steelmaking process as being a source of slag lines large enough to cause trouble

Jan 1, 1950

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman' for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man' has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman's model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman' derives the constraint on the linked-central force distortion on the basis of application of Pauling's relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By Jerry H. Service, F. L. Partlo

The following investigation was undertaken to develop a method for determining with reasonable accuracy the depth of overburdens of 100 ft. or less. Seismic methods seemed to offer good possibilities. The problem differed from that of the familiar salt-dome location in that the depth of overburden to be determined is much less than is encountered in oil prospecting. This means that a much shorter time interval must be measured with accuracy. Refraction methods seem at present to offer greater possibilities than reflection. The air sound persists for from 0.1 to 0.5 sec., because of echoes, and seismic reflections coming during this time are difficult to detect. A seismometer sensitive to vertical vibrations only offers possibilities and has been used here with some success. It is hoped that the application of this type of seismometer to reflection shooting in this region may be investigated still further. The apparatus used consisted of a carbon-button seismometer followed by a three-stage, transformer-coupled, vacuum-tube amplifier and a General Radio string oscillograph. Time marks are provided by a 1000-cycle, 600-r.p.m., synchronous motor provided with five spokes which intercept the light to the camera at 1/50 sec. intervals. This motor is driven by a two-stage vacuum-tube amplifier of 3 watt output, actuated by a tuning fork. The power supply for the seismometer amplifier is one 2-volt storage and one 45-volt B battery. The motor amplifier is powered by a 6-volt storage battery and 6 to 225-volt, 15-watt motor generator. The temperature-frequency characteristics of the tuning fork have been determined and for ordinary working temperatures the error in time that would be introduced is less than M millisecond for time intervals up to 100 milliseconds. The impact is produced by a sledge blow for surface distances less than 100 ft. and dynamite for greater distances. Two steel balls with wires attached form an electric circuit through a 1-ft. piece of railroad rail upon which they rest. When the rail is struck by the sledge the balls rebound, opening the circuit and indicating the time of impact by a break in the oscillograph record line as at A, Fig. 3. When dynamite

Jan 1, 1934

By Ralph Nichols

The mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are the Pittsburg Idaho Co., Ltd.; the Latest Out Mining & Smelting Co., Ltd.; and the Oilmore Mining Co., Ltd. Besides the above propertiea, there are a number of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course and a dip to the west of from 40' to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine. Character of Ore. The ores of the district are oxidized, carrying an excess of iron over the silica (insoluble matter). The vein filling is a mixture of limonite and hematite, which is replaced by shoots of lead-silver ores. The lead minerals consist of carbonate of lead principally, but with small quantities of sulphide, sulphate, and other lead minerals.

Jan 1, 1914

By R. A. Flinn, R. D. Pehlke, D. R. Glass, P. O. Hays

Knowledge of the depth of penetralion of an oxygen jet into the bath of the oxygen converter and of the correlation of penetration with driuing pressuve, lance heighl, and nozzle throat area is vital to the understanding of converter operation. If the penetration is too shallow, then severe and hazardous slopping takes place. On the other hand, if the jel penetrates entirely Lhvough lhe bath for an apprcciublc period of time, bottom damage occurs. In addilion to measurement of the penetralion of the jel, knou~ledge of the circulatory movement in the bath is also of interest in order to evaluale various theories oj-concerter operating behavior which have been published. In this investigation, experimental converters were buill of IOU- , 300-, and 4000-lb capacity. Four independent methods were used to determine penelralion: the onset of bottom marking, a nitrogen bubbler probe, observation througlt an optical syslew built into the oxygen lance, and direcl viewing of the jet issuing from the bottom of the vessel. Good correlation zuas obtained, and empirical relalions for pvedicling perletration were found. These relations were conjzrmed by bottom marking tests in 55- and 110-ton vessels. Within the operaling conditions employed in these tests, the depth to which a single oxygen jet penetrated zuas found lo vary according to the relatiorl ThE technical literature is replete with data concerning the successful use of the basic oxygen furnace or converter in steelmaking. Experimental data are lacking, however, on the vital factors of the depth of penetration of the jet into the bath and the induced circulation. Commercial operating conditions usually have been the result of cut and try experiments in lance manipulation until satisfactory results were obtained. There have been, however, two hotly argued opposing theories concerning desirable depth of penetration and these are exemplified by the Schwarz and Miles patents1,2 on one hand and the Suess patent3 on the other. The Schwarz patent teaches that the jet, issuing from the nozzle at supersonic speed, penetrates deeply "so that the reactions between the iron and the oxygen and between the oxygen and the rest of the smelting components take place in the center of the bath". Specific operating suggestions are given by Miles.2 By contrast, the Suess patent calls for surface Circulalion was investigated by lour methods: by direct observation in 200-lb open baths, by the use of graphite rudders in the 300- and 4000-lb converlers, by direct observalion through an oplical system in the lance, and by various models al room temperature. All were in excellent agreement and indicated that the motion of the bath ulas up at the center, radially outluavd at the surface, and down at the sides. Experi-ments in small and in commercial vessels indicate that it is essential to operate with a jet penetration of approximately 50 pct of the bath depth. Surface blowing results in low oxygen eficienty and in hazardous conditions which may render the process inopeuable. RejYactory dartzage al the bottom of the vessel is only encountered when the jet penetrates to the bottom, and this can be avoided by properly applying the penetration formula. The application of this en/pirical formula in commercial peraations is best when limited to combinations of lance size, pressure, and height which are typically encounteved in the use of a single-hole lance. blowing so that "...the oxygen jet does not penetrate deeply into the molten metal bath and is confined to an impingement area at the central portion of the bath surface". These references are given merely to illustrate the basic differences between the two schools of thought and to point out the need for measurement of penetration for the sake of the operator. For example, it is shown later that inefficient and even dangerous conditions can arise if improper blowing conditions are used. Differences are also evident between the two schools of thought as to the mixing, circulation, and agitation which is to be accomplished by the jet. The Schwarz patent states that "surface contact is not sufficient in most cases to bring about quick reaction, the same as the blowing of the gas over the bath surface or the mere blowing of the gas onto the bath surface". The patent goes on to call for active mixing. In contrast the claims of the Suess patent call for "discharging a stream of oxygen ... to an extent to avoid material agitation of the bath by the oxygen stream". In this patent the circulation is said to be downward in the center and up at the sides of the vessel. A number of investigators4-12 have explored penetration and circulation in transparent models. In general, it is agreed in these tests that the circulation is upward at the center (along the sides of the jet cavity),

Jan 1, 1968

By Ralph H. Sweetser

C. H. Herty, Jr.,* Pittsburgh, Pa.—The procedure of the Open-hearth Committee in studying pig iron and its effects in the open hearth has been influenced by the discussions at a number of meetings of the Committee. Those discussions have brought out very clearly that, as far as the pig iron affects the quality, interference with quality should be studied for three definite types of pig iron: (1) low-silicon pig iron; (2) very high-silicon pig iron, and (3) pig iron in which the silicon varies over a wide range in short periods, such as 1 to 3 casts. If a blast furnace is running steadily at 1 per cent. silicon iron, practically no trouble, apparently, can be traced to the pig iron, but if the furnace is running from 0.60 up to 1.50 and then down to 0.60 per cent., trouble in the finished steel is liable to occur, which apparently cannot be corrected by open-hearth practice. The open-hearth discussions have shown fairly definitely that with low-silicon iron, one type of trouble arises on the finished product and with the high-silicon iron, another. Our experience with the high-silicon is that any non-metallic matter that may form, does so when the pig iron is put into the furnace; that is, silicates immediately form which are more liable to be high in silica than would happen with low-silicon iron. I think Mr. Sweetser will agree with mc that if a blast furnace is very irregular, different points in the furnace may be working irregularly, in other words, the temperature gradient all over the furnace is not uniform. We have made many determinations on that point which indicate that a varying blast furnace causes hot spots and cold spots around the periphery. If some of those spots are hot and others are cold, although the analysis of the iron may be constant, then unreduced oxide, going through on one side, and good iron, going through on the other, may mix and the average temperature of the iron is not high enough to get completely rid of the oxides. So our method of attack is directly on that point; it is our first objective. Our procedure is to make a number of consecutive tests at a blast furnace, making a detailed study of the blast-furnace operation. We follow the iron through the open-hearth heat, being sure that we know just how much of each kind of iron gets into the open hearth, and take out specified samples at certain times during the process, working on steel where no finishing additions are made in the furnace. We are following one type of iron through the billet mills and into the finished product and are obtaining complete data on open-hearth operation. Besides the ordinary chemical analyses on the samples of slag and metal, we are running samples of the plg iron, the steel in the open hearth and the finished steel, for oxygen and silicates. We are going to find out whether or not oxygen, as silicates or oxides, has some connection with this trouble. If not, we may be able to locate some other factor. I am inclined to think that the silicates are responsible, judging from the indications in some other work that the Bureau of Mines is doing in Pittsburgh. We have laid out a very definite method of testing to which we will adhere at the different plants where we are now working and at others in the future. Our aim is to

Jan 1, 1927

By J. E. Pavlick, A. G. Guy

The total creep of tin alloys containing antimony in solid solution was observed to decrease with increase in antimony content. However, near the solubility limit an anomalous maximum in deformation was. found, in agreement with similiar observations by Bochvar. IT has long been recognized that alloys may deform more rapidly under stress if there is a tendency for a phase change or other structural change to occur simultaneously. However, the phenomena involved are complex and in some instances the opposite effect, strengthening, may result.' This area of research has not attracted much interest in the western world, and although Russian investigators have studied it for the past 15 years their work has not received due attention here. Recently diametrically opposing views on one aspect of this problem have been espoused by two Russian investigators, Kornilov and Bochvar. The question is this: in certain binary alloys tested in creep at the temperature where the solute is at the limit of solid solubility, does the incipient formation of the second phase strengthen or weaken the alloy? Korni-lov's arguments in favor of strengthening were presented at the 1954 Symposium at the National Physical Laboratory, =Creep and Fracture of Metals at High Temperatures.The most recent statement of Boch-var's theory of weakening is in Oding's new book on creep and rupture.3 Although Bochvar agrees that strengthening occurs in some alloy systems, he argues that in certain alloys an anomalous weakening is observed. However, the extensive work of Korni-lov's group on creep properties of alloy systems has not revealed any anomaly of this type, but instead has tended to refute Bochvar's theory. This clear-cut controversy offered a good opportunity for a simple experiment to resolve the problem. The experiment and its results supporting Bochvar are the subject of this paper. However, it will be helpful first to sketch the present status of the larger question of the effect of a phase change or other structural change on plastic deformation. PREVIOUS WORK One of the first researches in this area was by Pfei1,37 who investigated the creep resistance of an 80 Ni-20 Cr alloy containing varying amounts of titanium. He found that the resistance to creep increased rapidly as the solid solubility limit in the alloy at 775'c was approached and slightly exceeded. With further addition of titanium the creep resistance decreased, presumably because of precipitation effects. Bochvar's first work in this field was a study in 1945 of "superplasticity" in zinc alloys containing 15 to 25 pct Al.4 He found that alloys quenched from about 400 had anomalously low hardness when tested below this temperature. The following year, in a paper on the dependence of mechanical properties on the composition and structure of alloys,5 he extended some observations of Kurnakov to predict that at high temperatures of testing the hardness values for solid-solution alloys might be lower than those for the component metals. He also pointed out the influence of changes in solidus temperature in affecting curves of hardness vs composition, and he

Jan 1, 1962