Search Documents

By H. M. Rutherford

THE reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is .to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the sur-rounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently(7) ? regarding either the method or the results. The dis-covery of several oil fields is now attributed to the use of the reflec-tion method. Reflection methods have been used by the Germans to find the thick-ness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refrac-tion and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1932

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967

By J. J. Tietien, R. O. Clough

A technique previously used to prepare alloys of InAs1-xPx and GaAsl-x Px, miry: the gaseous hydrides arsine and phosphine, has been extended to grow single -crystalline GaAs 1-x Sb x by replacing the phos-phine with stibine. Procedures were developed for handling and storing stibine which now make this chemical useful for vapor phase growth. This represents the first time that this series of alloys has been grown from the vapor phase. Layers of P -type GaSb and GaSb-rich alloys have been grown with the carrier concentrations comparable to the lowest ever reported. In addition, a p-type alloy containing 4 pct GaSb exhibited a mobility of 400 sq cm per v-sec which is equivalent to the highest reported for GaAs. RECENTLY, interest has been shown in the preparation and properties of GaAs1-xSbx alloys, since it was predicted1 that for compositions in the range of 0.1 < x < 0.5, they might provide improved Gunn devices. However, preparation of these alloys presents fundamental difficulties. In the case of liquid phase growth, the large concentration difference between the liquidus and solidus in the phase diagram, at any given temperature, introduces constitutional supercooling problems. It is likely that, for this reason, virtually no description of the preparation of GaAs1-xSbx by this technique has been reported. In the case of vapor phase growth, problems are presented by the low vapor pressure of antimony, and the low melting point of GaSb and many of these alloys. In previous attempts1 at the vapor phase growth of these materials, using antimony pentachloride as the source of antimony vapor, alloy compositions were limited to those containing less than about 2 pct GaSb. This was in part due to the difficulty of avoiding condensation of antimony on introducing it to the growth zone. A growth technique has recently been described2 for the preparation of III-V compounds in which the hydrides of arsenic and phosphorous (AsH3 and pH3) are used as the source of the group V element. With this method, GaAs1-xPx and InAs1-xPx have been prepared2&apos;3 across both alloy series with very good electrical properties. Since the use of stibine (SbH3) affords the potential for effective introduction of antimony to the growth apparatus, in analogy with the other group V hydrides, this growth method has been explored for the preparation of GaAs1-xSbx alloys. In addition to GaSb, these alloys have now been prepared with values of x as high as 0.8. In the case of GaSb, undoped p-type layers were grown with carrier concentrations equivalent to the lowest reported in the literature. Thus it has been demonstrated that, with this growth technique, all of the alloys in this series can be prepared. EXPERIMENTAL PROCEDURE A) Growth Technique. The growth apparatus, shown schematically in Fig. 1, and procedure are virtually identical to that described2 for the growth of GaAs1-xPx alloys, with the exception that phosphine is replaced by stibine.* HCl is introduced over the gallium boat to *Purchased from Matheson Co., E. Rutherford,N+J. transport the gallium predominantly via its subchlo-ride to the reaction zone, where it reacts with arsenic and antimony on the substrate surface to form an alloy layer. The fundamental limiting factors to the growth of GaAs1-xSbx alloys from the vapor phase, especially GaSb-rich alloys, are the low melting point of GaSb (712°C) and the low vapor pressure of antimony at this temperature (<l mm). Thus, relatively low antimony pressures must be employed, which, however, imply low growth rates. To provide low antimony pressures, very dilute concentrations of arsine and stibine in a hydrogen carrier gas were used. Typical flow rates (referred to stp) were about 4 cm3 per min of HC1 (0.06 mole pct)+ from 0.1 to 1 cm3 per min of ASH, (0.002 to 0.02 mole pct), and from 1 to 10 cn13 per min of SbH3 (0.02 to 0.2 mole pct), with a total hydrogen carrier gas flow rate of about 6000 cm3 per min. Although no precise data on decomposition. kinetics exist, it is known4 that stibine decomposes extremely rapidly at elevated temperatures. However, the high linear velocities attendent with the high total flow rate (about 2000 cm per sec) delays cracking of the stibine until it reaches the reaction zone and prevents condensation of antimony in the system. To improve the growth rates of the GaSb-rich alloys, growth temperatures just below the alloy solidus are main-

Jan 1, 1970

By C. D. Rugen

GROUND raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grindability characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. CHARACTER OF GROUND RAW MIX (KILN FEED) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size, whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1945

By Robert F. Mehl

THE purpose of a symposium, I take it, is to gather together a group interested in a common intellectual field, in order to exchange views, and to appraise the state of knowledge. Symposia are the more successful, the greater the activity in the chosen field and the wider the range of applicability of the information gained. From time to time, as emphasis changes from one field of research to another, a given subject may enjoy popularity and later retire into a scientific somnolence, for fashions change even among engineers and scientists. The subject of this symposium, however, enjoys the advantages of wide applicability and of high current interest and productivity in results. It is a timely subject for a symposium; with much new information, surely metallurgical engineers should now devote an increasing attention to its application to practice. In beginning the symposium, I shall attempt briefly to appraise our basic knowledge in the field, to survey instances of practical usefulness, and to suggest where new work might be most productive of useful results. There are many examples of direct practical application of diffusion knowledge, and it is the purpose of the several papers in this symposium to review these. In this introduction I shall attempt to take a broad view, which, while it will but poorly serve the engineer in the solution of any given problem, may perhaps be of some use in assessing the state of knowledge in this field. RATE OF DIFFUSION Liquid Metals The process of diffusion among liquid metals, of gases in liquid or solid metals, or among solid metals, is ubiquitous, to say the least. The manufacture of alloys by the intermelting of metals, the addition of ferroalloys to molten steel, the deoxidation of molten alloys, all involve diffusion in the liquid state. The oxidation of molten copper for purposes of purification, the unsought oxidation of alloys generally during melting and casting, the reaction of liquid steel with oxidizing slags in the open-hearth furnace, the absorption of nitrogen by liquid steel, particularly in the bessemer furnace, all operate by the diffusion of gases in liquid metals. These processes have not been studied much from the viewpoint of rates of diffusion. Alloys are made by melting metals with stirring and with allowance of time for mixing (which is diffusion) but I know of no studies that seem to define the necessary times, and though in only very rare cases can faulty properties of the finished castings be ascribed to inadequate mixing, and though certainly in most cases, with stirring, the rate of diffusion is adequate to give sufficient mixing, a more quantitative treatment would be good to have. It is not wholly certain that thorough and sufficient mixing is at all times attained, for I suspect that ferroalloy additions to steel, and that additions of aluminum to steel as a deoxidizer, especially in the sampling of steels

Jan 1, 1944

By N. A. D. Parlee, I. D. Shah

The solubilities of oxygen in liquid Ag-Au, Ag-Pt, and Ag-Pd alloys have been determined in the range of 940° to 1200°C at 1 atm pressure of oxygen using an improved Sieverts technique. The additions of gold (0 to 57 pct), platinum (0 to 27 pct), and palladium (0 to 22 pct) to liquid silver continuously decrease the solubility of oxygen in liquid silver. Activity coefficients and interaction coefficients of oxygen in these alloys and have been calculated. The interaction coefficientscan be described by the following equations: Approximate second-order interaction coefficients (pM have been calculated. The contribution of the product, pMxNM, to In yo only becomes significant at high alloy concentrations. RECENTLY several investigators1"3 have redeter-mined the solubility of oxygen in liquid silver. In general the recent findings1" for Po, = 1 atm are in good agreement with the equation:4 log %O = 695.4/T + 1.086 [1] It is established1, 2 that the solubility of oxygen follows Sieverts&apos; law reasonably well, at least up to 1 atm partial pressure of oxygen. It should be noted that a very slight deviation from Sieverts&apos; law has been reported by Lupis and Elliott.3 Only recently has the solubility of oxygen in Ag-X binary liquid systems received much attention, and only the Ag-Cu, Ag-Au, Ag-Pt, and Ag-Pd systems have been studied. Par lee, Sacris, and zoellners reported that the solubility of oxygen in liquid silver increases progressively with the small additions of copper (0 to 0.5 pct) up to the point where the copper oxide phase appears. Lupis and ~lliott~ have reported that the solubilities of oxygen in liquid silver decrease progressively with the additions of gold, platinum, and palladium. However, their investigation was limited to 0 to 5 pct of these alloying elements, a range too limited to satisfy the requirements of the research program of this laboratory, where the solubilities of oxygen in the range of 0 to 30 pct were required for the calculation of chemical diffusion coefficients of oxygen in these alloys. The present paper deals only with the solubilities of oxygen in these alloys while another paper will deal with the diffusion of oxygen in these alloys. EXPERIMENTAL METHOD A Sieverts technique was employed which involved an improved design of the reaction tube, Fig. 1, as described briefly in a previous communication.4 Liquid melts (70 to 100 g) were held in Norton Alun-dum crucibles. The induction furnace used had a maximum output of 2.5 kw with very fine control. This induction system had excellent stability and the final equilibrium temperatures measured by calibrated Pt-Pt, 10 pct Rh thermocouples are believed to be within ±2C. These thermocouples were checked against the melting point of pure gold wire, and the results agreed with standard tables (±l°C). Each run involved a careful sequence of operations. The sample was heated to and held at about 900°C in vacuum for 3 to 4 hr with the thermocouple in a retracted position. After melting, the melts were usually exposed to a small amount of oxygen (0.5 to 2.0 cu cm) and then degassed slowly for 1 to 2 min to remove any oxidizable volatile impurities such as carbon and sulfur as CO, CO2, SO2, and SO forth. Argon gas was then allowed to enter the system. The protection tube containing the thermocouple was then

Jan 1, 1969

By J. G. Baragwanath

CUBA&apos;S lateritic iron ores, occurring on the northern coast of that island, though known to the Spaniards. did not receive any general attention until the close of the Spanish-American War. Preliminary studies of these deposits at that time indicated that the limonite contained small percentages of nickel and chrome, and it ryas subsequently discovered that although the average nickel content was only approximately 0.6 per certain limited areas of ore were suffiniently high in nickel to be considered commercial provided a suitable process fur its recovery could be developed. Early in 1937, Pardners Mines Corp. began a series of investigations which led to the development of such a process. Coincidentally, this company acquired option&apos; on certain properties in the Levisa Bay and Moa Bay regions and conducted a systematic campaign of exploration by test pits and hand-auger holes in the course of which an aggregate of 90.000.000 tons of ore was developed in eight deposits.

Jan 1, 1945

By Dorsey Hager

North Central Texas has recently become a center of interest for the oil men of America. The bringing in of the McClosky well at Ranger, Eastland County, and the shallow pool at Brownwood, Brown County, in 1917, has stimulated interest in this area to fever pitch. Oil men from all over the United States are now investing there. The area of present interest is shown by the accompanying map (Fig. 1). The money spent in leases runs into millions of dollars. It is no exaggeration to say that a strip of country 200 miles (321 km.) long and 125 miles (201 km.) wide, comprising some 15,000,000 acres (6,070,310 ha.), has been leased practically solid at a cost for rentals and bonuses of at least $1 per acre. The test holes contracted for will certainly number 400, at a cost of at least $5,000,000. From what has been done in the past six months, $20,000,000 at least will be spent. To pay returns on this amount of money, new production to the extent of at least 12,000,000 bbl. must be obtained. At present, the production from new fields will not average over 5000 bbl. per day; three wells at Ranger are producing 3000 bbl.; 250 wells at Brownwood produce 1000 bbl.; and the Gray well, Coleman County, is as yet an unknown factor. However, at Ranger there is every indication of developing a good pool covering from 1500 to 2000 acres (607 to 809 ha.), more or less, but the wells are deep, 3400 to 3800 ft. (1036 to 1158 m.), and cost $35,000 to $40,000 to drill. Large wells are necessary to pay for such expensive holes. As new wells are drilled, the gas pressure will be lowered rapidly, and large production need not be expected. For those oil men who expect a second Cushing or an Eldorado, Ranger holds little of promise. At Brownwood, Brown County, there are some 250 shallow wells (depths from 200 to 350 ft.) averaging 4 to 7 bbl. per day. There is a chance of an extensive producing area for these shallow sands to the southwest, and the opening of several thousand acres of shallow oil territory, and also some promise of deeper oil horizons in the Ranger horizon, but probably all under 2500 ft. At present, the lease brokers and speculators, and only a handful of oil men, have made any money. More fields must be developed, and it is more particularly with these possibilities that this paper deals. Lack of water for drilling purposes has undoubtedly held back development so far this year; this part of Texas has had a drouth for two years and there is an actual scarcity of water. Geological investigations so far undertaken cover nearly all the area outlined, and while pakt of the

Jan 1, 1920

By Ferit Gurses

EXTENSIVE coal and lignite deposits exist in Turkey. Bituminous coal is the nation&apos;s principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.1 It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. BITUMINOUS COAL The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total production of the basin was 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. AREA AND GEOLOGY OF THE COAL BASIN The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30° south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ½ ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By G. T. Brookman, P. B. Katz, D. K. Martin, J. A. Ripp

With the increasing emphasis on using American fossil fuel resources, more facilities are evaluating coal conversion. In addition, those facilities now using coal are considering better coal storage procedures to minimize negative environmental impacts. For example, rainfall and snowmelt on a coal pile produce a drainage stream high in acidity, suspended and dissolved solids, iron, sulfate, and trace metals. Usually, the characteristics of the runoff stream do not allow for direct discharge to streams and lakes. Detention in a holding pond and pH adjustment are traditional methods of treating coal pile runoff before discharge. Historically, this treatment methodology has been performed inefficiently without a good data base to assess how much runoff treatment is needed to meet effluent guidelines. A model was developed to simulate runoff volume and pollutant loadings under different rainfall conditions. This model will be used to size and design treatment works for coal pile drainage. The Ohio State University (OSU) version of the Stanford watershed model was selected as the base model. The OSU model simulates overland runoff in a rural area. It includes factors such as soil moisture, depression storage, infiltration, and flow to a ground water reservoir. TRC also used the OSU co-model for acid production in coal refuse piles as the basis for qualitative modeling work. A number of modifications were made to the OSU models to make them applicable to coal storage piles. The physical/chemical reactions included in the models are described in more detail in the project report. In addition, the models were altered so that a standard NOAA magnetic tape of historical meteorological data can be used as data input instead of requiring the user to create a data file. The resulting TRC coal pile drainage model is actually two models - a quantitative model, termed H2OTRC, and a qualitative model, TRCCOAL.

Jan 1, 1984

By J. D. Vincent, Pierre R. Hines

INTRODUCTION OF FROTH FLOTATION INTO THE UNITED STATES "The introduction and development of the flotation process have proved to be of such momentous importance to the mining industry of the United States that they deserve to be considered historically ." T. A. Rickard l James M. Hyde installed the first froth flotation process in the U. S., about Aug. 1, 1911, at the Basin Reduction Co. plant, Basin, Mont., which was then under lease to the Butte and Superior Copper Co.2 Two months later, the Minerals Separation Ltd.. filed suit in the U. S. District Court of Montana against Mr. Hyde char& him with infringement of their Patent 835, 120/1906. The U. S. District Court decided in favor of Minerals Separation Ltd. on July 28, 1913. This decision was reversed by the Ninth Court of Appeals in San Francisco on May 4, 1914. Then the U. S. Supreme Court, on Dec. 11, 1916, upheld the patent on three counts only but restricted it to &apos;the use of less than one percent of oil.” The Miami Copper Co. was sued by Minerals Separation on Oct. 10, 1914, for infringement of Patents 835,120 and 962,678, and 1,099,699. The Miami Copper Co. was operating under John M. Callow&apos;s froth flotation process Patent 1,104,755/~uly 23, 1914. Miami lost this suit in the District Court of Wilmington, Del., and appealed to the Court of Appeals, Third Circuit, Philadelphia. The Third Court of Appeals decided against Miami, May 24, 1917. The case was referred to a Master and hearings to determine profit and damages were not settled until 1923. Nevada Consolidated Copper Co. was sued Sept. 9, 1919, and Magma Copper Co. was sued Jan. 10, 1920. Thus, the first ten years of froth flotation in the U. S. were beset by patent litigation. This litigation suppressed the free circulation of new discoveries or useful information that might be cited in a patent suit against the originator; it accounts for many of the blank spaces in the historical record. T. A. Rickard3 has reviewed the history of flotation and has given the chain of discoveries, patents, and processes that resulted in froth flotation. He has re- ported also on the patent litigation beginning in 1911 and ending in November 1923, when Minerals Separation&apos;s Patent 835,120 expired. He comments on

Jan 1, 1962

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

By T. F. Witherbee

IN a paper read at the Lake Superior meeting, August, 1880, an account was given of the successful use of Rendrock and Monaky powder upon a scaffoldn and salamander in the furnace. On April 5th, 1881, the same trouble called for like treatment, which, though not so immediately. successful, was on the whole more instructive than the first trial, and points, I trust, to a reasonably sure remedy for all such difficulties. Up to December 4th, 1880, foundry and mill iron were made from Old Bed and New Bed magnetite, and Kearneyy red hematite, when a return was made to Bessemer iron, from an inferior quality of New Bed ore as compared with that used during first blast. January 18th, 1881, New Bed, Chateangay, and East-shaft, a newly-opened Bessemer deposit of Messrs. Witherbee, Sherman & Co., were first used, and continued up to February 13th, on a fuel charge of 80 per cent. anthracite and 20 per cent. coke, the product on the three ores being about 10 tons more per day than on New Bed alone. From this time until March 11th all coal was used, and New Bed, Chateangay, and East-shaft ores, up to February 22d, and from that date Chateangay and New Bed, the product falling off 9 6/10 tons per day as a result of not using coke. It is fair, however, to state that the furnace was not in good condition during&apos; this period, being over-burdened, and the New Bed ore was, temporarily, uncommonly poor, for reasons of no particular interest here.. It required to properly flux it at least 140 per cent. of limestone; and 101 per cent was actually used. March 11th, all Chateangay ore and 80

Jan 1, 1882

By G. E. Anderson

The Asientos-Tepezala district is in the north of the State of Aguasca-lientes, about 30 miles north of the city of Aguascalientes, the capital. The district is reached by a standard-gage railway on the west side through the junction, Rincon de Romos, which is on the main line of the National Railways of Mexico from El Paso to Aguscalientes. The terminal is Tepezala. On the east side a narrow gage connects Asientos with the junction, San Gil, on the main line, Asientos to San Luis Potosi. Tepezala on the west side of the Asientos hills is about 2 miles from Asientos on the east side. The area between the two mining centers is separated by a low subdued divide which forms the central part of the hills. The district is in a group of isolated hills surrounded by characteristic bolsón plains. The hills rise above the surrounding plains about 6500 to 10,000 ft.; the highest peak is Alta Mira. The two mining districts lie somewhat upon the flanks of the hills at about the same elevation, 7200 ft. The district is an old one and has been known since early in the 17th Century when the mines were worked by the Franciscan Monks. Their mining operations, which were limited to the oxidized ore above the water level, consisted chiefly in extracting silver from the Santa Francisca vein. To judge from the old workings and the remains of surface plant, the operations were on a large scale. By modern mining operations since about 1900, the various mines of the district have been one of the principal sourees of ore for the smelter located at Aguascalientes. Topography The topographic features of the Asientos hills are largely controlled by the character of the underlying rocks. During the Tertiary period, the entire group of hills was probably covered by extrusive volcanic material in the form of cones and lava flows. The central part of these have since been carried away by erosion, so that remnants have been left along the borders of the hills. These remnants form rather conspicuous peaks,

Jan 1, 1927

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By T. F. Witherbee

In a paper read at the Lake Superior meeting, August, 1580, an account was given of the successful use of Rendrock. and Monaky powder upon a .scaffold- and salamander in the furnace. On April 5th, 1881,&apos; the same trouble called for like treatment, which, though not so immediately successful, was on the whole more instructive than the first trial, and points, I trust, to a reasonably sure remedy for all such difficulties. Up to December 4th, 1880, foundry and mill iron were made from Old Bed and Sew Bed magnetite, and Kearney red hematite, when a return was made to Bessemer iron, from an inferior quality of New Bed ore as compared with that used during first blast. January lath, 1881, New Bed, Chateangay, and East-shaft, a newly-opened Bessemer deposit of Messrs. Witherbee, Sherman $ Co., were first used, and continued up to February 13th, on a fuel charge of 80 per cent. anthracite and 20 per cent. coke, the product on the three ores being about 10 tons more per day than on New Bed alone. From this time until March 11th all coal was used, and New Bed, Chateaugay, and East-shaft ores, up to February 224 and from that date Chateaugay and New Bed, the product falling off 9,8, tons per day as a result of not using coke. It is fair, however, to state that the furnace was not in good condition during this period, being over-burdened, and the New Bed ore was, temporarily, uncommonly poor, for reasons of no particular interest here. It required to properly flux it at least 140 per cent. of limestone; and 101 per ent. was actually used. March 11th, all Chateaugay ore aid 80

Jan 1, 1882

By Foster Bain

THE outstanding characteristic of the last hundred years has been the world-wide rise in the standard of living. Man&apos;s dominion over nature is increasing with an accelerating pace and more and more the forces and materials of this world are being made to serve man&apos;s necessities and his convenience. We demand both quantities and varieties of goods that were beyond the dreams, to say nothing of the reach, of our fore-fathers, and our possession of them has become so much a matter of course that they excite no remark. Literally, thousands of young folks have required an explanation of a recent popular song, "Thanks for the Buggy Ride," for the reason that their own experience does not extend back into the pre-flivver age. This transition from the use of vehicles made mainly of wood and drawn by animal power, to metal made cars propelled by mineral fuels is all but complete and the memory even of older conditions is already fading. This is symbolic of what is happening all around us. In a recent book, Dr. Frank J. Goodenough, president of Johns Hopkins University, referred to Chinese civilization as a ?vegetable" civilization meaning thereby that the Chinese depend mainly upon the plant world for food, clothing and other necessities and luxuries. Our own people did the same hardly more than a hundred years ago. In 1820, this country produced and used only 5 lb. of pig iron per capita, but a quick and enormous change was wrought in the hundred, years that followed, and in 1920 the amount was 119 times as much, or 597 lb. It has since increased even beyond this and touched a peak of 809 lb. in 1923. In that year our output was more than twice that of 1903 and nine times that of 1883. This increase in production

Jan 10, 1926

By R. G. Hawthorne

This report is concerned with fluid displacement in porous media, in those cases where viscous and gravitational forces control the displacement. Such a system would usually be found in a sand body of large physical dimensions such as an oil reservoir, although it is possible to create such a system in the laboratory. It is shown that the position of the fluid interface can be predicted by numerical calculations using a basic idea presented by Dietz. Fluid flow is considered in a vertical plane in a homogeneous, porous medium of sufficient thickness that the capillary transition zone is small in comparison with the total reservoir. A theory developed by Dietz&apos; is used to make numerical calculations of the position of the fluid interface. The results for several conditions are compared with scaled model experiments. The results show that, for gas drive in a reservoir of steep dip, a relatively low flow rate can displace large volumes of oil before gas breakthrough. On the other hand, water injection at favorable mobility ratio and low dip may show best performance at high rates. Water tends to underride the oil and, given sufficient rime, will break through without much oil displacement. For certain conditions, which include relatively low flow rate, the interface is a straight line and its behavior is simple to calculate. At higher flow rates, the interface is unstable, and a numerical solution was programed for an automatic computer. In general, good agreement is shown between the fluid model and the computed results so long as gravitational forces have control. For a water drive at very unfavorable mobility ratio, many small water fingers appear. These viscous fingers are not controlled by the relatively small gravitational forces. When viscous fingering becomes the controlling factor, the mathematical model is oversimplified, and results do not check the fluid flow model. INTRODUCTION Present methods of reservoir analysis depend upon certain simplifying assumptions to obtain mathematical descriptions of practical use. Material-balance methods (Muskat2 or Tarner2) assume uniform fluid saturations in the entire reservoir, or in a few subdivisions of the reservoir. An unsteady-state flow calculation by West, er at considered pressure and saturation changes in flow to a well during solution gas drive, and neglected gravity effects. Results showed only a 4 per cent difference for ultimate oil recovery by the Muskat method, even though the case chosen for study was one in which unsteady-state effects should be high. The Buckley-Leverett5 method commonly assumes a one-dimensional flow system. It is applicable at high flow rates where viscous forces predominate over gravity forces. Simultaneous, parallel flow of the two fluids is assumed, and the concept of a fluid interface is not introduced. Permeabilities to each fluid for a given saturation must be known. The method is not applicable for a two-dimensional system where cross flow becomes possible. Less well known is the displacement equation derived by Dietz. This method is designed for two-dimensional flow systems and assumes a definable fluid interface within the porous medium. Dietz showed that, for a range of low flow rates, the interface would be stable. straight and at an angle of inclination which could be simply calculated. At a certain critical flow rate, the calculated interface tilt would equal the formation dip. For higher flow rates, a finger of displacing fluid would invade the displaced fluid. Dietz indicated that his method applied only to macroscopic reservoir behavior, while the Buckley-Leverett method applied to the small transition zone at the fluid interface. The examples worked out in this report are based on the fluid-displacement theory of Dietz. It is shown that the Dietz theory may be used to derive equations analogous to the Buckley-Leverett equations. In contrast to the Buckley-Leverett method, flow is considered in a plane rather than being limited to a line. Rather than a frontal advance, the movement of a fluid interface is followed. For flow rates substantially exceeding the critical rate and for high viscosity ratio, many fingers of invading fluid occur-—rather than the single finger assumed by Dietz. On the other hand, so long as some gravitational influence remains, the flow is not entirely parallel to the bedding planes as assumed by Buckley and Leverett; therefore, both methods fail to give an adequate descrip-

This discussion of the paper of Chester W. Washburne should have been printed following the remarks of H. A. Wheeler, in Bulletin No. 100, April, 1915, pp. 835 and 836, but was inadvertently omitted. ROSWELL H. JOHNSON:-There is one reason why the hydrostatic interpretation of gas pressure is not wholly acceptable. As we go clown in the sands we seem to get excesses of gas. Particularly in this field it becomes excessive in quantity relative to the amount of water in the sand. If this holds in other fields as well it must mean that there has been an ascension of water, because these sedimentaries when laid down, were filled with connate water. If we do get an ascension of connate water, produced by some such phenomena as its expansion by heat or by the formation of new gas by pressure upon organic materials at great depth, we can hardly expect the pressure to be controlled merely hydrostatically. * In reply to Mr. Wheeler&apos;s inquiry as to gas wells with pressure higher than hydrostatic pressure, I would cite the original wells given by Orton on which he based the hydrostatic theory. He used in his calculation a head of 600 ft. above tide, assuming the outcrop of the Manitoulin Islands to be in Lake Superior, whereas the Trenton does not outcrop at Lake Superior. The Manitoulin Islands are in Lake Huron, the level of which is 580 ft. above tide. No allowance is made for the lower density of the fresher water near the outcrop, the weight taken for the whole column being the water of high density found at the wells.

Jan 5, 1915

By E. H. Snow, B. E. Deal

Instability effects in semicanductor devices have long been attributed to the motion of charges on or within oxide layers on the surface. These effects are of critical importance in metal-insulator-semiconductor MIS) field-effect devices. For this reason, the capacitance-voltage or the conductance-voltage characteristic of these devices can be used as a sensitive detector to study charge transport and polarization effects in the oxide or insulator. A review is given of the results of such studies of thermally grown SiO2 as well as of other insulating films of importance in silicon technology. Three types of effects are distinguished. The first of these is the drift of mobile cations within the dielectric, examples being thermally grown SiO, which is often contaminated with sodium ions, and a variety of other glasses in which the mobile ions are a part of the glass composition. The second effect is a dipole-type polarization which occurs in phosphosilicate glass films obtained by reacting P2O5 with thermally grown SiO2. The third effect involves the transfer of charges between the dielectric and the silicon electrode. This occurs in silicon nitride and other deposited dielectrics. It is concluded that MIS studies have provided a powerful technique joy the study of charge transport and polarization effects in insulating films. The knowledge gained from these studies has led to an understanding of surface effects on conventional transistors and diodes as well as making possible stable MIS transistors. THE metal-insulator-semiconductor field-effect transistor is conceptually the oldest type of active semiconductor device.&apos; The earliest attempts at making this device were frustrated because of high surface state densities at the interface between the semiconductor and the gate insulation.&apos; However, by using a silicon substrate with thermally produced silicon dioxide as the gate insulation, this problem was solved and metal-silicon dioxide-silicon devices with good characteristics were made as early as 1960. 3 Yet it was still over 5 years before these devices became a commercial reality. This delay was largly due, not to surface states, but to stability problems associated with polarization effects within the insulating layer which caused the threshold voltage of the device to drift under temperature and bias treatments. The solution to these problems has not only made possible stable MIS devices, but it has added immensely to our understanding of failure mechanisms in conventional bipolar transistors and has added to the reliability of ali types of planar devices. In this review, we shall first describe the effects of various types of polarization phenomena on MIS device characteristics. Then, since thermally grown SiO, is by far the most important insulator used in these devices, we shall review historically the type of instabilities which have been observed in thermal oxides, the attempts at understanding and eliminating them, and the present status of the problem. We shall then turn our attention to the various deposited insulators which have been used, including lead glasses, phosphosilicate glass, vapor-deposited silicon oxide, and silicon nitride. Interestingly enough, many of these materials show polarization effects which are quite different from those generally observed in thermally grown SiO2. THE EFFECTS OF POLARIZATION PHENOMENA ON MIS CHARACTERISTICS The simplest MIS device and the one which has been most frequently used in the study of polarization effects is the MIS capacitor. Two modifications of this structure with single- and double-layer dielectrics are illustrated in Figs. l(a) and (b), respectively. The capacitance of this structure as a function of voltage applied to the metal gate electrode is plotted in Fig. 2 for the case of an n-type silicon substrate. When the silicon surface is accumulated (positive bias) the measured capacitance is just that of the insulating layer C. When the surface is inverted (negative bias), the capacitance is that of the insulator and a silicon depletion layer in series CoCs/(Co + Cs). Indicated on the horizontal axis of Fig. 2 is the voltage VT at which the silicon surface becomes strongly inverted. This voltage corresponds to the threshold or turn-on

Jan 1, 1969