Search Documents

By Klaus Schoenert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such subprocesses as: transportation of the particles to the zone where they are stressed; the stressing of particles to a level high enough for breakage; removal of the fragments that are smaller than the limit size from the grinding zone; and prevention of agglomeration of the fine fragments. Breakage phenomena of particles is the most difficult subprocess to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. Two important features of the "Science of Communition" are discussed: the fracture physics and crushing under controlled conditions with special reference to single particle crushing, packed bed crushing, measurement of energy needed for fracture, fragment size distribution, and new surface area produced. The important features of these aspects are detailed, namely, energy balance of a crack, influence of environment, specimen size problems, and energy utilization in single particle crushing.

Jan 1, 1973

By P. R. Sperry

Aluminum alloy 3S was examined to determine the relationship between the applicable phase diagram and the microstructures produced under conditions tending toward non-equilibrium as well as equilibrium. The only phases present in the alloy were aluminum, (Mn,Fe)A16, aAI(Mn,Fe)Si, and silicon. It was found that the alloy behaved essentially as though it belonged to the Al-Mn-Si system. The effects of various solidification rates and of various homogenization treatments were studied. Particular attention was given to a nonuniform precipitate distribution which reflected the solute distribution in the cast aluminum solid solution. Some possible explanations for the solute distribution based on characteristics of the Al-Mn-Si or AI-Mn systems were discussed. ALUMINUM alloy 3s (aluminum plus 1.25 pct Mn) is one of the oldest and the most widely used of the wrought aluminum alloys. In spite of this fact, there are some aspects of the metallography of 3s which have not been revealed or which have not been brought to the attention of the metallurgist working with the alloy. The purpose of this investigation was to demonstrate in general how some of the fundamentals of equilibrium phase diagrams may be applied to the study of an alloy and to show specifically the origin of certain metal-lographic features of aluminum alloy 3s. It is hoped that this information can serve as a basis for solving specific problems relating microstructure to such things as mechanical properties, recrystallization, grain growth, and surface finish. Literature Survey Considering that alloy 3s contains only one alloying addition, manganese, it seems reasonable that it would have characteristics pertaining to the A1-Mn system. However, those characteristics might well be altered by the impurities in the commercial alloy, especially iron and silicon. Therefore, not only the simple binary but also more complex systems had to be reviewed. One characteristic of the A1-Mn system worthy of mention is its sluggishness, which leads to conflicting solubility data1,'2 and makes it relatively easy to supersaturate the solid solution and shift the eutectic composition during rapid solidification.3'4 Another characteristic is the strong influence which small amounts of impurities, especially iron, exert in lowering the solid solubility of manganese. Undissolved manganese is ordinarily present in an intermetallic phase, MnAl,, having an orthorhombic crystal structure. A metastable precipitating phase designated as "G" has been reported but small amounts of iron and silicon suppress this phase entirely." Raynor has established that MnA1, can dissolve a considerable amount of iron by a substitution of iron for manganese atoms up to 50 atomic pct.'" Consequently, in the Al-Mn-Fe liquidus diagram, the eutectic valley separating the primary aluminum and (Mn,Fe)Al, fields is fairly close to a constant Mn + Fe content." This is an important consideration in regulating the composition of 3s and also other aluminum alloys with high manganese additions."

Jan 1, 1956

By George D. Roberts

INTRODUCTION CIVIL engineers are primarily interested in maximum core recovery. This is even more important in foundation work than in mining investigations where sludge samples are of some value. The soft materials, such as clay, gouge, or partially decomposed seams that are most readily ground up or washed away, are the materials that usually have the greatest influence on foundation and leakage conditions. Undisturbed samples of such materials should be obtained for detailed geological examination and laboratory tests. Therefore the attainable goal of sampling in connection with foundation investigations is the recovery of 99.9 pct of undisturbed core. FACTORS CAUSING CORE LOSSES The principal factors contributing to core losses are: (I) coring badly fractured or very soft material; (2) use of improperly designed coring equipment, including the use of bits of too small a diameter; (3) lack of the proper training and attitude on the part of the drillers and pertinent technical information on the part of the supervising personnel. Little can be done about the character of the material being cored but the other two factors contributing to unsatisfactory performance can be corrected. Although the title of this paper is the improvement and standardization of core barrels, it is believed that the drillers' shortcomings and the lack of pertinent technical literature are more detrimental to good core recovery than either of the other factors. USES FOR LARGE DIAMETER CORE BARRELS It is well known that the use of larger diameter bits and core barrels generally produce better cores, particularly when sampling soft or broken material. The use of larger and larger bit diameters and the insistence on better core recovery is well demonstrated by the change in practices of the various districts of the Corps of Engineers. Today NX core is the smallest diameter commonly permitted for investigational work and the more active districts are using coring bits up to 6 in. in diameter, as well as 36 and 40-in. calyx rigs. The latter size has proved to be just as economical because it provides more room for core removal and cleanup operations. The use of large diameter cores to replace the driving and jacking methods of obtaining soil samples is also increasing. The 5 7/8-in. Denison sampler, developed by H. L. Johnson to obtain samples from soft formations, is one example. The principal uses for bits larger than NX are: sampling soils and semi-consolidated rock; sampling decomposed rock or rock with soft seams; sampling concrete; obtaining samples for laboratory tests; drilling drainage holes, and other miscellaneous work. CORE DRILLING PRACTICES OF SEVERAL ENGINEER DISTRICTS Little Rock District The writer was employed in the Little Rock District from 1938 until 1942. Prior

Jan 1, 1947

By J. H. Yang, K. E. Gray

Results of single-blow bit-tooth impact tests on saturated rocks under elevated confining pressures and zero pore pressure were reported in a previous publication.1 This paper presents an extension of the earlier work to include a study of crater formation during tooth impact on both gas- and liquid-saturated Berea and Bandera sandstones at elevated confining and pore pressures. The basic data obtained were force-time, displacement-time, velocity-time and force-displacement curves during crater formation. Crater volume was also measured and the mode of crater formation determined. Bit tooth geometry, depth of penetration and velocity of impact were held constant. Results indicate that, with pore fluid present in the rock, failure trends from brittle to ductile as pore pressure is increased at constant confining pressure (pore pressure and borehole pressure were equal) For a given rock type, the mode of crater formation was dependent not only upon the nominal effective stress, but also upon the fluid which saturated the rock pore space. When confining pressure and pore pressure were equal (zero nominal effective stress), bit-tooth impact resulted in brittle failure for nitrogen-saturated Berea, and brittle to transitional failure for nitrogen-saturated Bandera; when saturated with liquid both rocks failed in a ductile manner at zero nominal effective stress. INTRODUCTION Dynamic wedge penetration tests have been conducted by investigators in several fields, but the failure mechanism of rock under dynamic stresses is not understood completely. The complex action of drilling bits, even considering the action of a single tooth, may be considered as a combination of drag bit and rolling cutter action. Thus, as a first step in understanding rock breakage in oil well drilling, single chisel impact and rock planing are of fundamental importance. For example, Gray 2 and Crisp3 studied drag bit cutting action at brittle stress states. Simon4 and Hartman5 studied the reaction of rocks to vertical impact by means of drop tests. The depth of penetration, crater volume and force-vs-time curves during crater formation were observed. The significance of indexing single-bit impacts has been noted.4,6-8 Gamer et al,9 reported impact tests on impermeable Leuders limestone at atmospheric and elevated confining pressures. In all cases the tests were accomplished on dry rock and pore pressure was considered to be zero. The importance of both confining pressure and pore pressure on the failure characteristics of rock was described. 10-12 It was found that the yield strength and ductility of porous rock depend on the state of stress under which the sample is tested. The importance of pore pressure on drilling rate in microbit experiments was noted by Cumingham and Eenink. l3 Robinson 12 also pointed out that in drilling the most important parameter in rock failure is the effective stress, where effective suess is defined as confining pressure pc minus pore pressure pp. The effect of pore pressure and confining pressure on rock strength was also noted by Serdengecti and Boozer 14 in strain rate tests, and by Gardner, Wyllie and Droschackl5 in elastic wave studies. Until recently all reported wedge impact studies under simulated wellbore stress states have been conducted on dry rock. Maurer 16 reported impact tests on samples saturated with deaerated water. Borehole and formation fluid pressures were equal in these tests except when mud was used in the borehole. With mud in the borehole and a high borehole-to-formation fluid pressure differential. Maurer observed "pseudoplastic" crater formation. Podio and Grayl reported impact tests on Berea and Bandera sandstone saturated with pore fluids having wide ranges in viscosities. In Podio and Gray's tests, confining pressure was elevated, but pore pressure and borehole pressure were held fixed at atmospheric pressure. The presence of

By J. Parke Channing

WE are accustomed to think that we are efficient in the United States, particularly with respect to such things as mining and manufacturing. The conduct of the war has demanded in England and in France a complete readjustment of manufacturing methods and plans, and today England is probably as efficient a country as there is in the world, not even excepting Germany. This is all the more remarkable because it has been notorious for years that England has been inefficient in her manufacturing and the country has been flooded with things "Made in Germany." Today England is almost a socialistic community and the State is doing almost everything. England is now in such a position that practically everyone in the country is engaged in industry necessary for the conduct of the war, and this has been accomplished by increasing the efficiency both of her tools and of her man power. In the United States we certainly have been efficient so far as machines and perhaps so far as methods have been concerned, but we have not been efficient iii the utilization of our man power. Before the war, our labor was undoubtedly far more efficient than that of England, but it certainly was not so highly efficient as it should have been, and the problem that confronts us today, and will all the more confront us after the war, is to make our man power efficient. England has had a taste of what you may call State Socialism, and her laboring men are not going to be content to return to the old order of things. There is one feature of the labor problem in England which has permitted her to reach this condition of state socialism with comparative rapidity; this is that practically all of her laborers are English; she has little or no foreign population. While an Englishman may he a strong union man and ready to fight his employer tooth and nail, at heart he is still a British subject, and when his country was in danger he rose to the occasion.

Jan 5, 1918

By Bradley Stoughton

PROMINENCE has been given lately in engineering circles to the question whether an organisation with manifold interests can be as effective as one with a single aim, especially if that single aim be the furtherance of affairs of moment and the welfare of engineers in general. In its earlier days, the A. I. M. E. was forbidden by its constitution to engage in non-technical public affairs, but the members altered the constitution in this respect, in the year 1912, in response to the growing demand that engineers be more human in their interests and that the engineering societies represent them in this respect. Since that time, the activity of mining engineers in public affairs has been growing rapidly, and we are happy that the Institute has been able to render very valuable economic services. Doubtless the greatest public service rendered by engineers in a recent great emergency was the work of the Naval Consulting Board, without which the U. S. Navy would never have been able to enter promptly into service upon our entrance into the war, ,and both Navy and Army would have been a long time without the munitions that came at an early date. We can never forget that this Board was established through the direct activity of the then President of the A. I. M. E., with the hearty cooperation of other national organizations.

Jan 1, 1920

By J. E. Norton

PRODUCTION statistics show that during the period of emergence from the depres¬sion the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee + was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1939 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechaniza¬tion program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. SUMMER WORK An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the ac¬celerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con¬cerning the coal industry to the under¬graduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program - was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war badly scrambled the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid develop¬ment in some men. We could readily single out the men at the opposite ends of the scale of competence. COMPREHENSIVE TRAINING PROGRAM Having adopted summer work as a

Jan 1, 1946

The Anglovaal Group has released details concerning its new processes for recovering platinum group metals, stating that the Group's system, which involves batch processing and precipitation methods for these metals (PGM's), leads to faster recovery times, increased recoveries, and higher purities than the conventional process. Insofar as South Africa's Merensky Reef is concerned, the Anglovaal method of recovering palladium first (as opposed to platinum in the conventional process) enables it to use a much simpler process in the subsequent recovery of platinum and other metals. Because the processes give cleaner separations, the volume of material to be recirculated -and therefore the total volume of material in the recovery circuits- is reduced substantially.

Jan 3, 1976

By Thomas F. McLoughlin, David K. Hylbert

A new method of satellite imagery analysis has been developed during underground mine roof research. Landsat positive film transparencies were projected onto topographic base maps to scale and lineaments enhanced with a Ronchi grating (method A). Thirty-five millimeter slides of video-enhanced scenes were also projected onto base maps (method B). Both methods permit direct plotting of lineaments to scale and direct correlation with surface and subsurface data wing transparent overlays.

Jan 1, 1981

With only one certain exception coal was never used by the Indians, before white men came to America, for any purpose except as an ornament or for paint. Within the past few years it has been discovered that the Hopi Indians in Navajo County, Arizona, used lignite for burning pottery, about 1000 A. D., as dated by tree rings. They were able to obtain a clear color in their ware that could not be obtained with brushwood fires. The coal was mined by hammers from outcrop openings, some of which can still be seen, and the tools used have been found in them.1 (See also p. 376.) Small figurines made of splint or cannel coal have been found at various localities in western New York, in Ohio and possibly other places, evidently made for ornaments. There is no reason to think they are of any greater age, if as old, as that mentioned above. Some crushed coal was used by the Indians as a black pigment in painting themselves, but apparently the eastern Indians never used coal for any other purposes. Some think that several tribes of Indians in the Northwest, along the Missouri, used coal as fuel, the basis being a statement attributed to Radisson about 1660. In the Jesuit Relations of 1659-1660 it was stated that Radisson anti Groseilliers had just returned from a visit to Lake Superior and beyond. "In the country of the Poualak, which means 'warriors' they say `as wood is scanty in supply and small in size in their country, nature has taught them to make fire with coal from the earth (charbon de terre) and to cover their cabins with skins.'"2 This statement was only hearsay with the good fathers, and the reputation for veracity of the two explorers is not of the best, and it is extremely probable that instead of coal they used turf, dry grass or buffalo chips. In fact in Radisson's Voyages' he does not mention coal at all in his account of the third voyage, when he was supposed to have seen it used. His accounts of his travels are badly mixed, and he and his companions were much better travellers than narrators. None of the early travellers up the Missouri River saw any evidence even then that the Indians were familiar with the use of coal. In the writer's opinion it is unlikely that coal was used as stated by the Jesuits.

Jan 1, 1942

By E. O. Jones, E. Whitehead

During the heating of cold-worked nickel silver, the tendcncy of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. Changes in Alloys During Heating and Cooling During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting1 suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320" C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 1, 1926

By R. J. Wagner, G. H. Gronhovd, A. J. Wittmier

The paper describes the results of a series of full-scale boiler tests run to determine the ash fouling characteristics of a North Dakota lignite as a function of sodium content of the coal. Four levels of sodium were investigated and rate of fouling was determined both by boiler performance and by specially constructed probe equipment. Discussed is information on chemical and physical properties of the ash deposits. The vast lignite deposits in North Dakota are becoming increasingly important as a source of low-cost fuel for power generation. A new 200-megawatt lignite-burning plant located near Stanton, N.D., was placed in operation early in 1966. Another 172-mega-watt unit in the same area is scheduled for operation late in 1966, and plans have recently been announced for a 212-megawatt unit to be in operation by 1970. If these plants show good performance, western North Dakota could become a major power production center for a large geographic area in the upper midwest. One of the problems associated with the use of lignite in power boilers is its tendency to form troublesome ash deposits on boiler tube surfaces. This problem varies considerably from one lignite-fired boiler to another and is dependent upon such factors as source of lignite, boiler design, load factor, tube metal temperatures, and soot-blowing practices. This report presents data on sodium content* variation in a North Dakota mine, describes the results of a series of tests performed to determine the relationship between ash fouling tendencies and the sodium content, and tells how the mining company and electric utility have coordinated their operations to reduce the ash fouling problem. GENERAL BACKGROUND Until recent years it was generally assumed that North Dakota lignite from a given mine had qualities peculiar to that mine, but that within the mine, the lignite was quite uniform. In 1959, the Otter Tail Power Co. installed a 53.5-megawatt lignite-burning unit at its Hoot Lake plant, Fergus Falls, Minn. Shortly after the unit was put into operation, it was noted that at certain times under high load conditions, ash fouling problems were quite severe, but not consistent or predictable. Each time fouling occurred in the unit the position of the loading shovel at the mine was noted. Within two years it became apparent that there were certain areas in the Knife River Coal Mining Co. mine at Beulah, N.D., where the lignite apparently had a high fouling tendency for the Hoot Lake unit. Results from analyses of the coal did not show large differences in moisture percentage, ash percentage, heating value, or ash fusion temperature between the highly troublesome and less troublesome coals. After three years of operation, the troublesome areas had been quite well defined and the mining company started a procedure of bypassing these areas when load conditions at the plant were high and then returning to the troublesome areas to load the lignite during the summer months when peak loads were lower. It was noted that the lignite from the areas which caused severe fouling under high load conditions produced much less fouling at the lower summer loads. However, bypassing certain areas in the strip pit caused the mining company to disrupt their continuous loading schedule, which in turn upset their continuous stripping schedule and made for less efficient mining operation. Meanwhile, at the Hoot Lake plant, the number of soot blowers on No. 2 boiler had been increased from 30 to 55, and a very rigorous blowing schedule had been adopted resulting in soot blowers operating at least some part of 21 hrs per day. Fouling problems continued, with a resulting reduction in plant economy and reliability. During this period the Federal Bureau of Mines Coal Research Laboratory at Grand Forks, N.D., had initiated various research programs relating to the study of lignite ash and ash fouling problems. One project was a survey in which full seam samples were obtained from various locations in all the major

Jan 1, 1968

Raymond Weir Smyth, born Nov. 3, 1888, was the son of Herbert Weir Smyth, professor of Greek Literature at Harvard University. He graduated (A. B.) from Harvard in 1909 and later pursued advanced studies there in chemistry and in metallurgy. He held the position of metallurgist for the American Steel and Wire Co. at Worcester, Mass., and also for the Steel and Tube Co. at Youngstomn, Ohio. For a time he was inspector of munitions for the British Government and stationed at the Railway Steel and Spring Co. at Latrobe, Pa. For a short time, in 1917, he was Inspector of Ordnance for the U. S. Government, and the following year, having entered the U. S. Naval Reserve Force, he was ordered in a similar capacity to the Midvale Steel Co. In September, he removed to the Navy Yard, League Island, Philadelphia, to train for the obligatory minimum of six months' sea duty. There he contracted influenza, which was followed by pneumonia, from which he died, September 27, at the Navy Yard Hospital. Captain Braxton Bigelow* Captain Braxton Bigelow was the son of Major John B. Bigelow, U. S. A., retired, and grandson of the late John Bigelow, author, and Minister to France under President Grant. Captain Bigelow graduated

Jan 1, 1920

Raymond Weir Smyth, born Nov. 3, 1888, was the son of Herbert Weir Smyth, professor of Greek Literature at Harvard University. He graduated (A. B.) from Harvard in 1909 and later pursued advanced studies there in chemistry and in metallurgy. He held the position of metallurgist for the American Steel and Wire Co. at Worcester, Mass., and also for the Steel and Tube Co. at Youngstomn, Ohio. For a time he was inspector of munitions for the British Government and stationed at the Railway Steel and Spring Co. at Latrobe, Pa. For a short time, in 1917, he was Inspector of Ordnance for the U. S. Government, and the following year, having entered the U. S. Naval Reserve Force, he was ordered in a similar capacity to the Midvale Steel Co. In September, he removed to the Navy Yard, League Island, Philadelphia, to train for the obligatory minimum of six months' sea duty. There he contracted influenza, which was followed by pneumonia, from which he died, September 27, at the Navy Yard Hospital. Captain Braxton Bigelow* Captain Braxton Bigelow was the son of Major John B. Bigelow, U. S. A., retired, and grandson of the late John Bigelow, author, and Minister to France under President Grant. Captain Bigelow graduated

Jan 1, 1920

By W. M. Weidel

While electric lamps both of the cap and hand type are being introduced into many mines requiring the use of safety lamps, the oil-burning safety lamp is still used in the great majority of cases, and even where the former are used the latter must continue to be employed when testing for gas. It is not the intention to discuss here the relative merits of the two types, but simply to give a comparison of the illuminating effect or candlepower of several kinds of ordinary safety lamps used for general work and for testing. Few data have been published in recent years on this subject and because of this it is hoped that the following information may be of some interest and value. The lamps tested were in all cases of standard size and in good condition, all practically new, and were selected from a collection of about 100 with a view to obtaining results on as many different common types as possible. With the exception of the gasoline-burning lamps, five different oils were used in each lamp to determine whether particular oils were suited to particular lamps and whether there was any great difference in the illuminating power of the different oils, or whether some oils would maintain their illuminating power better than others throughout a working period of 8 hr. No attempt was made to determine the amount or cost of oil burned by each lamp, but the condition of the lamp, wick, glass, and gauzes was noted after each test. Description of Apparatus Used The candlepowcr was determined with a Weber photometer, Fig. 1, which consists of a tube A containing a movable milk-glass screen adjustable by the milled screw B. The distance of this screen from the standard light at C is read on the scale attached to A. The standard light consists of a benzine lamp so arranged that the height of the flame may be adjusted exactly by observing it against a scale in the lamp box through an opening in the front. The lamp to be tested is placed at D so as to illuminate a milk-glass screen in the holdcr at E. At the intersection of the axes of tube A and sight-tube F are placed two 45' prisms with their surfaces in contact so that the light from D may pass through with-

Jan 1, 1917

By Persifor Frazer

I DESIRE to say that, owing to the number of papers which have been more or less crowded at this session of the Institute, and the fact that, as one of the Local Committee, I have the distinguished honor to feel somewhat like one of the hosts, I should not tax the patience of members at this late hour, but would have my paper read by title were it in any way possible to do this. But the task I have set myself this evening is to present to the eyes of the members of the Institute certain objects which have occupied more or less of my time during the last eighteen months or two years. The objects I allude to are some of the igneous rocks of this country, which, until quite recently, have been less understood than any others. It will be well known to some of the members that some of the cooled lavas of a previous age of our planet, when not directly coarsely crystalline and granular, were considered and spoken of as " natural glasses," or perfectly uncrystalline, vitreous, or hyaline masses of matter. Among the first results of the use of the microscope was the dispersion of this fallacy. Sir David Brewster, Mr. H. C. Sorby, and William Nichol (the discoverer of the celebrated calcite prism, which bears his name), had, with greater or less success, examined sections of various rocks and minerals, both by transmitted and reflected light, and also in the form of powder. But, until the genius of Vogelsang undertook the subject, these investigations had no permanent value, nor did they constitute an independent line of mineralogical and geological research. Since the close of his labors, by Vogelsang's premature and much-lamented death, the subject has been made one of renewed interest by his brother-in-law, Ferdinand Zirkel, as well as by Rosenbusch, Tschermak, and many others abroad, and at home by the commencement of a systematic study of the traps of Connecticut by Messrs. E. D. Dana and G. W. Hawes, of New Haven, and by the splendid set of described sections of the traps of the West which have been furnished by Zirkel to illustrate Clarence King's report. I had the honor of presenting a large number of thin sections of our traps at the Washington meeting, for the inspection of the members, with the aid of a table microscope belonging to the Smithsonian Institution. Here I propose to project these sections upon the

By M. E. Wadsworth, I. B. Cutler

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the ( potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum ( potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the i potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.' Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as pH, reagent concentration, and floc size and density.2 Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By J. J. Forbes

THE Federal Coal Mine Safety Act (Public Law 552, 82nd Congress) was approved on July 16, 1952. It incorporates, as Title I, the Coal Mine Inspection and Investigation Act of May 7, 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title II contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires, inundations, and man-trip or man-hoist accidents. At this point a brief account of events that pre- ceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Government as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coal- mine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small force of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations after mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia, I11., disaster of March 25, 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act.

Jan 1, 1954

By H. S. Price, J. C. Cavendish, R. S. Varga

This paper presents a new technique for solving some of the partial differential equations that are commonly used in simulating reservoir performance. The results of applying this technique to a simple problem show that one obtains accurate pressure values near wells, as well as accurate pressure pdients, which can be explicitly calculated. The method is completely rigorous in that convergence of the discrete numerical solution to the continuous solution for both pressure and pressure gradient is established. High-order, piecewise-polynomial approximations are used near the wells where pressure gradients are steep, while low-order, piecewise-polynomial approximations are used elsewhere to reduce greatly the calculation time. This combination is shown to give a uniformly good approximation to the solution. These approximations, obtained by using a Galerkin process with suitable Hermite subspaces, are shown to be theoretically and numerically superior to the usual approximations obtained from standard finite-difference techniques. Not only are much greater accuracies obtained, but computer times are also greatly reduced. The application of this technique to multiphase flow problems (e.g., single well coning problems) would have considerable practical interest, but such extensions of this technique with full mathematical rigor have not been made as yet. However, the numerical methods presented here are general, and in principle extend to multidimensional, multiphase flow. Moreover, the preliminary results given in this paper are sufficiently encouraging that we feel the effort in attempting these extensions is justified. INTRODUCTION The problem of obtaining accurate pressure distributions and pressure gradients around wells is of considerable importance in the numerical simulation of reservoir performance. The most common approach to solving this problem is to use finite difference techniques (see McCarty and Barfield9 or Peaceman and Rachfordl0). This approach, however, has many disadvantages, the major one being that many grid points are generally necessary for accurately describing the pressure distribution and the pressure gradient around wells. This need for a fine grid results in large computer times and often in prohibitively high costs. Besides investigating the method of finite differences, some authors, such as Welge and weber17 and Roper, Merchant and Duvall,13 have considered a combination of analytical and numerical techniques with some success. These approaches, however, are all nonrigorous and quite often cannot even be applied. In this paper, we present a numerical formulation of high-order accuracy, based on the Galerkin method, for solving this problem. We treat here only the partial differential equation that describes steady-state, single-phase flow. However, the methods presented are general and in principle extend to multidimensional, multiphase flow. Specifically we treat special cases of the problem in two dimensions described by: where G is a rectangle (with sides parallel to the coordinate axis) with boundary ?G, ?/?n denotes the outward normal, and y and B are non-negative constants such that y + B > 0.

Jan 1, 1970