Search Documents

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1938

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division, and revised in 1939. Generally in Table 1 the unit for prescntation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each spacc in the tabulation, it is citller (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are detcrminable but not detcrminable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries arc not subject to precise determination. In such rases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1939

THERE has been a lot of talk about the shortage of engineers and we have done our share of it; but recently we heard a spot radio commercial-between broadcasts-urging high school seniors to study engineering. We think this is going too far. Engineering is an exacting profession requiring the highest personal qualifications. Publicity for the purpose of interesting capable young people in choosing courses in engineering should emphasize qualification. The opportunities for a career in a great constructive profession which is the basis of our high standard of living should be properly evaluated. Although there is a need for more engineers today, nobody knows what the employment potential is going to be four years hence. The profession may do itself a grave disservice by attempting mass recruitment in the face of an unpredictable national economy. The mining and metals industries are in a special position as fewer engineers are needed in these fields. Only 10 pct of all engineers are mining and metallurgical engineers. Today's shortage is not so much in recent graduates, but in trained practicing engineers. The shortage has served the profession to good effect because it directed the talents of engineers into more productive channels. In some areas high school graduates have been put into routine jobs such as, surveying. If there is one thing the mining profession does not want, it is an oversupply of graduates which would relegate college men to years of work and discouragement in routine jobs. The public has a clear cut picture of the legal and medical professions and thus the respect knowledge imparts. But the engineer is variously thought of as a man who pulls the throttle lever on a locomotive, tends a furnace, or builds a bridge. The term engineer is too loosely used. For instance we have heard of "crowd engineers" and "exterminating engineers." In some unions an engineer designation has been established to describe a person doing routine checking or other control job. We do not disparage these positions but they are different from the work done by the man qualified by years of experience and study. Many of these so-called engineers are not engineers at all. The engineering profession has cooperated closely on a program of recruiting high school graduates for engineering study. It should start a cooperative public relations program to enlighten the public on the accomplishments and work of engineers. This type of publicity need not be of the bombastic type. It can be educational and dignified. Radio, television, and the periodicals can be used to convey information. It is time that laymen and interested young people learn to make a distinction between the true engineer and the technician. Such a program would instruct parents and high school students and thereby interest the right type of people in the engineering profession. The Centennial of Engineering sponsored by the American Society of Civil Engineers is a step in the direction of instructive public relations. This fine start should not be allowed to remain as a one pass venture. The engineering profession as a whole should follow this exposition with a sustained, well directed effort to inform the public of the engineer's work and the possibilities it holds for a constructive career.

Jan 1, 1952

By Charles Luner

ALTHOUGH the kinetics of the atmospheric oxidation of tin have been studied,1-3 the kinetics in pure oxygen have not been reported. This note presents some results of the kinetics of the oxidation of tin foil in pure oxygen. The tin foil used in this investigation was 99.78 pct pure, the two major impurities being Pb (0.17 pct) and Sb (0.024 pct). The foil was degreased and air-dried prior to oxidation. The air-formed film was estimated by coulometric reduction4 of the surface oxides to be about 25A. The samples, which were in strip form and had a total geometric surface area of about 300 sq cm, were first evacuated at room temperature in an oxidation bulb to 1 X 10 -5 mm Hg and subsequently degassed for 1 hr at the temperature of the experiment. Spectroscopically pure oxygen was then introduced into the bulb. The rates of oxidation were measured by following the rate of pressure change due to oxygen consumption in a closed system, the volume of which was sufficiently large so that the pressure change during an experiment was 10 to 15 per cent of the total pressure. An oil-mercury manometer,5 with a sensitivity of 3 X x mm Hg (which corresponds approximately to 5 X 10 -7 gm of oxygen) was used to measure the pressure change. The oxidation bulb was heated by an oil-bath and controlled to within -10.3 C. The reproducibility of the rates was good, as determined by the coincidence of rates at 190oC for duplicate experiments. Fig. 1 shows the oxidation curves in the temperature range 168 to 211.5oC at 8 mm Hg pressure. The effect of pressure on the rate of oxidation at 190°C is also shown. The rate of oxidation was not markedly affected by changes in pressure in the range 4 to 9 mm Hg, except perhaps at the lowest pressure, 4 mm Hg, where after about 70 min there appeared to be a decline in the rate, as compared with the rate at the higher pressures. At the lower tem- perature, 168oC, and for short reaction times, it is difficult to distinguish between a linear relationship and a slight curvature in the oxidation rate. However, for longer times, there was a somewhat larger indication of curvature. The samples after oxidation were gold-colored in appearance. The oxide that was formed at 170°C was identified as a-SnO by reflection electron diffraction. This is in agreement with results obtained by other workers.6, 7 The rate data best fitted the logarithmic-oxidation rate law, w = K1n ln(1 + -t/to) [1] where w is the weight of oxygen consumed, t is the time, and K In, and to are constants. First estimates to were obtained according to the method of Taylor Thon8 and were then employed to obtain the best simuItaneous estimates of to and K In, that would fit the logarithmic expression. These estimates were found numerically, so that the residual variance could be minimized. The calculations were performed on an

Jan 1, 1961

By J. A. B. Forster

W. G. WOOLF*—The paper has a wealth of data that take careful, detailed study. As has been indicated the highlights can be only touched in the paper. The design and the arrangement of the rabble teeth as well as some of the other details of operation show a very careful study and a scientific approach to the problem which in most plants using hearth roasters are matters of trial and error with empirical conclusions and, perhaps too often, just arbitrary supervisory preferences which may be erroneous. Here the problem has been approached from a scientific angle which think well merits careful study. The ability to treat the tonnages they get through these furnaces think is made easier by reason of the high sulphide sulphur in the resulting calcines which the balance of the plant—the leaching and so on—can cope with. As indicated by Mr. Weldon in his dis- cussion earlier this morning, in most zinc plants an attempt is made to have as low a sulphide sulphur content in the roaster calcine as possible. But in the operation of the Risdon plants, they are able to cope with sulphide sulphur content up to 5 pct which is far beyond the amount of sulphide sulphur that can be handled elsewhere. I think the autogenous roasting is made easier because driving out the last percentages of sulphide sulphur brings on the necessity for extraneous heat, and that is further exemplified because even at Risdon the author shows the desirability of using some oil to better the operation, particularly for uniformity of roasting results and to obtain more regularity of furnace operation. A. A. CENTER*—Regarding the hard crusts in the beds of the furnace and autogenous roasting, the paper speaks of the former being due, at least to a considerable extent, to lead sulphide in the crusts. I wonder if the author has considered the hard crusts as being due in large part to zinc sulphate. While I was developing large zinc operations we ran into hard crusts which had to be dug up. I took several lumps which were so hard they showed the marks of the rabble teeth very plainly and kept them in my office for some weeks. A visitor came along one day, and as he was having similar troubles, I told him what we were doing about ours. I started to pick up one of these lumps and to my amazement the thing crumbled in my hands whereas originally it had been so hard it wore the rabbles down very rapidly in the furnace. I sent the sample to the laboratory and found that it analyzed very high in water-soluble zinc and sulphate-sulphur. The crumbling of the lumps was evidently due to the anhydrous zinc sulphate gradually taking on moisture from the air and forming crystalline zinc sulphate seven parts water. The increase in volume would, of course, result in disintegration of the lumps. As to getting a high tonnage in the autogenous roast, that is partly because of finishing at about 5 pct sulphide sulphur. It is a real job to get down to, say, ½ pct sulphide sulphur, which is what is usually desired, and still put through a good tonnage.

Jan 1, 1950

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly dzerent stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report l,8x,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1937

By E. J. Pasierb, H. W. Paxton

Mavkers ill a diffusion couple in the iron-chromium system move towards the high chromium side indicating Dcr > DFe at the marker composition. By a combituztion of measurements of D& and D a: a function of composition, this is also shown independently. DFe is calculated as a function of composition. and shown to be in reasonable agreement with measured values by other workers. MEASUREMENTS of marker movements in diffusion couples have been used from time to time to demonstrate that a vacancy or interstitial mechanism may be operative. Since there is a possibility that ring diffusion1 may be operative in chromium, the present experiments are of interest in showing some non-ring mechanism in iron-chromium alloys around the equiatomic composition. EXPERIMENTAL PROCEDURE The movement of markers originally at the interface between 1-in. sq sections of pure Cr (6 mm thick) and outer slabs of 30 Cr-70 Fe alloy was followed as a function of time at temperatures from 1150" to 1425"C, in a Kanthal-wound furnace. Temperature control was +5°C over extended periods. The analyses of these alloys are given in Table I. Selection of suitable markers presented a considerable experimental problem; the eventual solution was to draw quartz rod down to 0.01 cm and seat this in V-grooves 0.01 cm deep on each side of the chromium prior to welding. A preliminary experiment in which the groove was machined in the alloy gave identical results. Welding was accomplished by passing a heavy current through specimens under moderate pressure in a helium atmosphere. This method produced good welds with a planar interface as shown by subsequent metallo-graphic investigation. Any markers which did not adequately fill their groove and showed subsequent contamination from the atmosphere during heat treatment were not considered reliable. The composite sample was ground and metal-lographically polished on the four sides perpendicular to the interface. Fiducial marks (deep milled slots) were made outside the diffusion zone to check on total volume change. All necessary measurements were made on a metallograph reading to +0.0005 cm. The samples were wrapped in tantalum foil and given diffusion anneals for times to 200 hr in carefully purified dry hydrogen in a sealed McDanel porcelain tube. Chromium-zirconium chips were introduced near the specimen as an additional getter. The specimens were cooled relatively slowly after the diffusion anneal to preserve the McDanel tube but no significant error in effective time at temperature was thereby introduced. At least 1 mm was ground off the surface before measurements were taken. It was observed that the grain size following short diffusion anneals was several mm and was appreciably larger in the 30 Cr alloy than in the pure Cr. No significant grain boundary penetration was present as indicated by the etch limit. The results are presented in the next section. Measurements of D were made by standard sectioning techniques with chemical analysis. Machining difficulties limited the

Jan 1, 1961

By R. N. Orava, L. A. Rice

One of the difficulties encountered in the preparation of titanium specimens for transmission electron microscopy is the formation of a surface hydride phase during the thinning operation at ambient temperatures. This necessarily destroys contrast, obscures features of interest, and often leads to misleading results. By cooling the polishing solution to temperatures below 0°C this problem has been overcome in the past.' However, since the cooling procedure is somewhat inconvenient, a technique was developed at this laboratory for thinning titanium at room temperature. The material examined was A-70 grade commercial-purity titanium purchased from the Crucible Steel Co. of America. The mechanical and thermal treatments, described elsewhere,* yielded a recrystallized grain size of 4 to 5 p. A slice, 0.5 mm thick and 1.5 mm wide, was cut from a bulk specimen2 using a diamond cut-off wheel. The sample was then coated with paraffin wax. Two concentric holes, about 0.03 in. in diam, one at each broad face, were scribed through the wax to the surface of the metal. Subsequent polishing for several minutes resulted in a preferentially thinned or "dimpled" region. Thereafter, the wax was removed and the entire specimen polished to the point of breakthrough at the base of the dimple. Polishing was effected chemically in a solution comprised of 30 pct HF and 70 pct HN03 by volume, kept at room temperature (20" to 25OC). The specimens were mounted in a stereo holder and examined at 100 kv in a Philips l00 B Electron Microscope. A micrograph from a foil prepared in this way is shown in Fig. 1. Several points are noteworthy. This electron micrograph shows neither evidence for the formation of a hydride phase due to specimen preparation nor, moreover, any obvious surface contamination in electron-transparent areas of a freshly prepared foil. Localized variations in foil thickness observed in some specimens seem to be a characteristic of this chemical polish but do not seriously detract from foil quality. With care, the lifetime of a good specimen exceeded 2 hr in the beam. On the other hand, the exposure of a sample to air at atmospheric pressure, when still warm from the beam, clearly resulted in the deterioration of a formerly clean area just previously in the field of view. An example in Fig. 2 of a contaminated region reveals features, and "spots", not unlike those observed in much purer material by Yamane and Ueda. Consequently, one can conclude that: 1) titanium can be thinned satisfactorily in a solution at room temperature for transmission electron microscopy; 2) large-scale precipitates, >50A in diam, are absent in commercial-purity, recrystallized, furnace-cooled, A-70 titanium containing about 3800 wt ppm interstitials and the same amount of iron; 3) care must be taken not to attribute surface contaminants to precipitates. The authors are grateful to the Franklin Institute for financial support and permission to publish.

Jan 1, 1967

By J. L. Meijering

Oxidation hardening of cylindrical and spherical specimens first decreases with depth below the surface, but then increases again as the center is approached. This is in agreement with the view that this change in hardness is mainly determined by the change in velocity of the oxidation boundary, which affects the dispersion of the oxide. WHEN a thick slab of silver containing 0.3 pct Mg by weight is internally oxidized, the hardness measured on a cross section is found to decrease considerably with distance from the surface.&apos; This phenomenon has been attributed to the diminution of the velocity of the oxidation boundary. The smaller this velocity is, the more slowly the free-oxygen concentration rises towards the concentration in equilibrium with the oxygen gas. And a small 0 concentration favors dissociation and thus conglomeration of the oxide. For instance, the hardness decreases more rapidly during long annealings in nitrogen than in air.&apos; Measurements by Gregory and Smith3 on sections through internally oxidized Al-silver wire showed a smaller variation in hardness, probably because the wire diameter was only 0.9 mm. Wood4 found a drop in hardness with depth in internally oxidized Al-copper strip, and also—by electron microscopy—the concomitant increase in Al2O3 particle size. Under certain circumstances internal oxidation leads to formation of rather irregular inner oxide films in the midst of dispersed oxide. This special sort of conglomeration—discussed in Ref. 5—is also favored by greater depth below the surface.3,5 In this paper hardness measurements in large diameter cylindrical and spherical specimens are described. Here the oxidation velocity* goes through ness initially decreases with depth but increases again towards the center. Normally, the diffusion coefficient D1 of oxygen is very large compared to D2, that of the dissolved metal. If, furthermore, the atomic fraction c2 of the latter is much larger than the O-solubility cl- but c2D2 << c1D1- the velocities in question are easily calculated2 to be: for the cylinder and for the sphere. Here p is the radial coordinate of the oxidation boundary and R the specimen radius, which in dilute silver alloys is constant, as no external oxidation occurs. These equations have been derived for a divalent solute; for nondivalent solutes c2 has to be multiplied by half the valency. The equations are not valid near the center. For which can be considered as a standard case,2 the Eqs [I] and [2] begin to yield U-values which are appreciably too high for p/R = 0.05 and 0.15, respectively. But at the v-minima they are still very good approximations. These minima lie at p = emlR= 0.37R in the cylinder and p = 1/2 R in the sphere. Other factors besides the velocity v will also influence the hardness. The oxide concentration cox is constant in a flat strip, apart from a narrow region in the middle,2 but in cylindrical and spherical specimens cox decreases steadily with depth. When C1 << c2 and c1D1 >> c2D2 one can calculate

Jan 1, 1961

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants&apos; producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors&apos; reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably her product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too he, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater dificulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1947

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably her product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too he, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater dificulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1947

By H. I. Smith

The technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe there is accord, I will distinguish between booster and auxiliary fans. Definition of Booster and Auxiliary Fans In discussing underground fans G. S. Rice1 distinguishes between those used to increase the amount of air passing a given point and those used to augment the ventilation locally. He describes a booster fan as one which is installed to handle the entire air current passing a given

Jan 1, 1927

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien&apos;s Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By G. R. Mansfield, W. B. Lang

THE third year of Government exploration for potash by the U. S. Geological Survey and the U. S. Bureau of Mines under the authorization of the act approved June 25, 1926 (Public 424-69th Cong.) is drawing to a close. The results thus far obtained are thought to be sufficiently interesting and satisfactory to justify the presentation of a brief preliminary account of the work. Review of Earlier Exploration The general geologic similarity of the Permian basin of Texas and New Mexico to the potash field of Germany had long ago suggested the possibility of the presence of potash salts somewhere in that basin, but petroleum exploration was then making little headway there and the necessary data could not be obtained. The discovery by Udden in 1912 of potash in brine from the Spur well in Dickens County, Texas, was the first direct evidence of its presence. In 1915-17 the U. S. Geological Survey drilled a test well with standard tools at Cliffside near Amarillo, but failed to find potash. Nevertheless, an observer has been kept in the field, at first in cooperation with the Texas Bureau of Economic Geology but since 1922 by the Survey alone, to secure data and samples from oil and gas tests. Since the discovery of oil in Reagan County in 1923 exploration by drilling has been rapidly extended to many parts of western Texas and southeastern New Mexico. The identification of the potash-bearing mineral polyhalite was first announced by the Geological Survey in June, 1921, the material having come from cuttings from the Bryant well in Midland County and the Burns well in Dawson County, Texas. Successive discoveries and announcements of similar purport aroused widespread interest in potash exploration, which culminated in the action by Congress already noted. Permian Salt Basin The Permian salt basin extends generally northeastward from western Texas and southeastern New Mexico through the Panhandle sections of

Jan 1, 1929

By G. H. Kennedy, H. E. Criner

CYCLONE thickeners are "hydraulic centrifuges" designed either to produce a maximum practical separation between the water and solids of a feed slurry or to classify the slurry solids according to particle settling rate. The possibilities of utilizing the thickener to "close" plant water circuits have been investigated. Since the thickener becomes an integral part of the plant water circuit when installed, the basic means by which the solids content of all circulating water systems must be controlled is reviewed. All coal not separated from the circulating water by means of dewatering screens or settling devices must be bled from the plant at the same rate as they are being fed or created by degradation. If this were not true, the circulated volume would finally be completely filled with solids. If the rate of bleed is low, the solids concentration in the bleed and circulating water generally will be high. To keep a reasonable circulating water concentration, large amounts of fresh water must be supplied and the bleed rate must be high. These conditions are usually undesirable because of the difficulty in securing fresh water, the loss of large quantities of coal, and the pollution of nearby streams. Thickeners are the primary stage in the separation of the water contained in the bleed from the coal. Since a thickener, when operating with reasonable efficiency, usually cannot be expected to deliver an underflow containing less than 50 pct water, secondary dewatering devices such as a slurry screen or vacuum filter must be used to separate additional water from the bleed. The surface area required by the filter or screen will be nearly proportional to the total water which must be handled, and therefore the thickener becomes necessary to hold down the original cost. The water separated from the coal is then returned to the plant circuit to maintain the water balance and thus becomes the source of fresh water. It is not necessary to return clear water to the plant to maintain control of the circulating water concentration. It is only necessary that the bleed dewatering devices remove coal in all sizes at a rate equal to that at which these sizes are entering the circulating water. However, practically speaking, in order to maintain low solids concentration, it is usually necessary that the thickener have good recovery characteristics on bituminous coals in those sizes down to 400-mesh. The thickener can remove the smaller sizes from the closed-circuit system at the "solids in" rate and prevent their "build up" in the circulating water as shown in Fig. 1. With the portion of the feed water going directly to the underflow, comes the very fine solids not concentrated by the cyclone. All the larger solids are removed from the feed and delivered in a concentrated condition at the underflow. To apply thickeners with some reasonable assurance that operating requirements will be met, it is necessary to know the rate at which solids of all sizes must be removed from the circulating water and to know the thickener characteristics. The required removal rate of fine solids not recovered by other dewatering devices may be estimated from the size distribution and tonnage of the plant feed with a reasonable allowance for degradation in the circulating water system. A more reliable estimate may be secured by sampling the plant bleed water during a constant load period.

Jan 1, 1952