Search Documents

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell' have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By Bruce A. Kennedy

This is an opportune time to examine the disposition of practical rock mechanics in the mining industry. The rock mechanics world has put on steam with publication of a number of books and the organization of a large number of symposia and teaching seminars. SME has just published Stability ill Open Pit Mining. proceedings of a conference held In November 1970 in Vancouver, R.C. R book entitled Planning Open Pit Mines covering the entire range of open pit mining with emphasis on slope stability has just been published by the South African Institute of Mining and Metallurgy. The Thirteenth Symposium on Rock Mechanics was held at the University of Illinois. Urbana-Champaign, during the last week of August. The University of British Columbia's Division of Continuing Education is holding a symposium and specialty seminars on stability in open pit mining during the first week in November. A tremendous planning effort has started to organize the Tl3ii.d Congress of the International Society of Rock Mechanics in Denver in 1974. This meeting is held every four years in the country of origin of the president of the Society. This third congress comes to the U.S.A. with Leonard Obert of the 17. S Bureau of Mines as president of the Society. The previous two were held in Lisbon. Portugal and Belgrade. Yugoslavia.

Jan 1, 1971

By Richard J. Mainiero

INTRODUCTION Because of the hazards associated with flammable methane gas and coal dust, the shooting of mudcaps (adobes) or other unconfined explosive charges in underground bituminous coal mines is prohibited; all explosives must be fired in stemmed boreholes. However, there are situations where it would be advantageous from a safety standpoint to fire open shots. This would be in the areas of dislodging loose roof slabs, overhangs, rock-fall leveling, slab or boulder breaking, crib removal, and crevice shooting. The Bureau of Mines, U.S. Department of the Interior, has been developing an explosive charge that is non-incendive; that is, detonation of the charge will not ignite a flammable atmosphere. This explosive charge could be applied to the blasting conditions mentioned above. As of this writing, the explosive charge has not yet been certified as "permissible" for use in flammable atmospheres, but the necessary protocol is being finalized with the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The explosive charge described in this paper is merely a prototype sheathed rock-breaker charge (sheathed permissible explosive rock- breaker charge) demonstrating the feasibility of such a device. Industry may modify the design and composition of the charge in producing a commercial product so long as it is still safe, as defined by a testing schedule being developed by the Bureau of Mines and MSHA.

Jan 1, 1984

By George H. Ashley

At the beginning of the war, about 13 years ago, a conference was called in Washington to lay plans for pooling the coals of the United States. A careful review of the various systems of classification then extant showed none well adapted to the needs of coal pooling. The system of Tidewater pools then adopted, using numbers to distinguish one pool from another, was based on typical coals of different localities. At that time, the writer undertook the preparation of such a practical classification. Aside from drawing on his experience of over 20 years in the coal fields of the United States, reaching from the Pacific Coast and the Rio Grande to Rhode Island, he first examined and carded all of the large collection of coals in glass jars made by and for M. R. Campbell. Next, he carded all of the descriptions of coals he could find in the U. S. Geological Survey bulletins and elsewhere, as well as practical tests of coals by the Navy and other organizations and then took account of every published coal analysis of the U. S. Geological Survey and U. S. Bureau of Mines. A study of this information, involving thousands of recomputations, led to the presentation of a paper on "A Use Classification of Coal" before this Institute at the Chicago meeting, September, 1919. That classification was unique (1) in a classification based on "standard coal" which included moisture, but used standardized ash, sulfur and nitrogen, (2) in using physical properties to distinguish the major classes or orders, (3) in recognizing British thermal unit values in the minor subdivision, (4) in the large number of classes recognized (thirty-six), (5) in proposing mineral names for all classes, (6) in proposing a letter code for the several classes for practical use, (7) in proposing a code for expressing what has commonly been called "grade" of the coal, the grade code to be combined with the rank code to designate and describe a coal. The writer still thinks that the principles then offered, though not necessarily the exact proposals, are valid and desirable in any practical classification. The actual classification of coal by rank was based on the ratio of fixed carbon to volatile matter for the high-rank coals—the well-known

Jan 1, 1930

By R. C. Buehl, J. P. Morris

ACTIVITY values for sulphur dissolved in liquid iron and slags as functions of composition and temperature are needed in applying thermodynamics to sulphur-control problems in iron- and ' steel-making. The purpose of this investigation was to determine the effect of carbon on the activity of sulphur in the metal phase. The method employed was the same as that used in an earlier investigation' concerning the effect of silicon on sulphur activity in liquid iron. A study was made of the conditions of equilibrium in the reaction between hydrogen gas and sulphur dissolved in iron-carbon alloys. The chemical equation for this reaction can be written as follows: S (in liquid Fe-C alloy) + H2 (gas) = H2S (gas). It was found that the activity coefficient of sulphur in liquid iron increases as the carbon content increases. At 2.3 pct carbon and 1600 °C, the activity coefficient of sulphur is twice its value in carbon-free iron, and at carbon saturation it is more than six times as great. The effect of temperature on sulphur activity was found to be small. Previous work on the reaction between hydrogen gas and sulphur dissolved in liquid iron has been reported by several investigators2,³,4 but only recently have studies been made of the effect of alloying elements. Silicon1 is known to have a pronounced influence on the activity of sulphur in iron, its effect being similar to that shown by carbon as described in the present report. Kitchener, Bockris, and Liber-man5 recently have published a preliminary report of their work on the effect of carbon on sulphur activity in iron. Their experiments were made at 1570°C and carbon saturation in the melt. Under these conditions they found that the activity coefficient of sulphur was approximately doubled by the presence of carbon. This is a much smaller effect than that found in the present work. Experimental Method: The apparatus and procedure were essentially the same as those used in the earlier investigation of the effect of silicon on sulphur activity.' Briefly, the method was as follows: A molten iron-carbon alloy was brought to equilibrium at constant temperature with a mixture of H2 and H2S of constant composition by bubbling the gas through the metal. Samples of the melt were

Jan 1, 1951

Coal Transport Via Pipe Line Claimed Feasible Moving coal via pipe line is a project proposed by the U. S. Bureau of Mines. A pipe line 100 miles long capable of transporting 5000 tons of coal a day with water could be built for about $10 million. The cost of moving the coal 100 miles would be between $1.28 and $2.01 a ton.

Jan 9, 1951

By F. Garofalo

It has been shown by various investigators that during constant stress creep the dependence of minimum creep rate, 6,, on stress, o, is given by em = A onat low stress levels, md by 6, = A' exp [ß s] at high stress levels. In these relations A, n, A', and ß are constant at constant temperature. A single relation has been found which satisfies conditions for both high and low stresses and agrees well with experimental results. This relation is 2, = AN (sinh a s)n, where A" is a constant at constunt temperature and a = p/n. This relation also satisfies the linear relation, 6, = k s, found at temperatures near the melting point at low stresses. EXPERIMENTAL creep results have led to a number of empirical relationships between minimum creep rate, 6,, and the applied stress, s. Under conditions of constant stress it is generally found that at low-stress levels,'-' the dependence of minimum creep rate is given by 6, = Asn. At high-stress levels'74 the experimental results fit the relation, 6, = A' exp [po l. In these relations A, n, A' and ß are constant at constant temperature. A model based on climb-of-edge dislocations from a pile-up array leads to a relation similar to that found experimentally at low stresses.' On the other hand. theories based on chemical-reaction rate,5 nonconservatively moving dislocation jogs, and jog migration and climb-of-edge dislocations4 lead to a relation similar to that found experimentally at high stresses. No difference in mechanism between low and high stress levels has been clearly defined; it is questionable whether such a difference really exists. In any event, the major argument usually given in substantiation of a change in mechanism from low to high stresses is that no single relation exists for defining the stress dependence of the creep rate over wide ranges in stress. However, such a relation has been found and is of the form, dm = A" (sinh a s)n, where A" is a constant at con- stant temperature and a = ß/n. This relation agrees well with experimental results over wide ranges in stress and temperature for copper, aluminum, an A1-3.1 pct Mg alloy, and an austenitic stainless steel. STRESS DEPENDENCE OF MINIMUM CREEP RATE At low stress levels the minimum creep rate, gm, depends on the stress, 0, under conditions of constant stress creep through the relation em=Aon [1] The quantities A and n have been defined previously. In the range in which this relation applies, a linear dependence is found in a log em,-log o plot. Above the stress range of application of relation [I], the minimum creep rate increases much mar; rapidly than predicted by relation [I]. This behavior is shown in Fig. 1 for a series of creep tests on copper4 at various temperatures ranging from 673 o to 973°K. Relation [I] is satisfied at the lower stresses, although the results at 973°K are quite limited. In all cases the transition beyond the applicable range of relation [I] is a gradual one indicating no abrupt change in mechanism. For all test temperatures, values of n have been determined from the results in Fig. 1. These are reported in Table I under Alog tm/hlog o. At high stress levels the stress dependence of minimum creep rate under conditions of constant stress is given by im = A' exp [ß a] 2] All factors have been defined previously. In a log em-0 plot, relation [2] predicts a linear function. Experimentally, a pronounced deviation from the prediction of relation [2] is found at lower stresses. As the stress is lowered, the minimum creep rate decreases more rapidly than predicted by relation [2]. This shown for copper in Fig. 2. Again it is found that the transition from high to low stresses is gradual and no really sharp change is found. Values of p determined from the high stress results are given in Table I. The dependence of minimum creep rate on stress at constant temperature for all ranges in stress

Jan 1, 1963

H. W. NICHOLS, Secretary-Treasurer, Field Museum of Natural History, Chicago, Ill. , R. S. BONSIB, H. B. PULSIFER, . HORACE H. CLARK, H. T. WALSH. Seventy-four members of' the two organizations attended a three-day joint field meeting of the Chicago Section and the Illinois Mining Institute at La Salle, Ill., on May 17, 18 and 19. The meeting began with a technical session in the rooms of the Illinois

Jan 7, 1917

By John F. Elliott, John P. Hager

The standard free energies of formation of the lowest stable sulfides of chromium, molybdenum, and tungsten in equilibrium with the corresponding metal hazle been determined by reacting the sulfide and metal with H2(g)/H2S(g) mixtures. The reaction is A method for estimating the standard ~nolav entropies and standard entropies of formation at 298°K of the sul-fides of refractory metals is presented. The standard free energies of formation of the lowest sulfides of the metals in group VIa of the periodic table are probably best determined with the reaction* is known with greater accuracy than is that property for any other sulfur-bearing compound or solution which might serve as a reference phase to establish the chemical potential of sulfur for the essential re- However, there still remain significant problems to the use of Reaction [I] in studying these sulfides. First, the equilibrium gas ratios (Ph2S/PH2) are very small, and with the most stable sulfides in the series the ratios tend to be at the limit of the range for precise chemical analysis (10-4); and second, the reaction rate for the formation or reduction of these sulfides appears to be relatively slow. A primary reason for the latter problem is that the gas phase near the equilibrium concentration has very little capacity for transport of sulfur. It is to be noted that the thermo-dynamic properties obtained from the experimental results by Eq. [I] apply for 1 g-atom of sulfur in the metal-saturated compound even though the exact composition of the compound has not been determined. The work reported here is a study of the standard free energies of formation of the lowest sulfides of chromium, molybdenum, and tungsten, and of copper, by Reaction [I]. In planning the experimental program, it was decided that the technique that has been used previously3"' could be used with modification and that an improved analytical method was needed for determining H2S in the gas phase. THE EXPERIMENT The once-through flow of gas was selected in preference to recirculating the gas, a) because of the low sulfur capacity of the gas, b) because of the relatively slow rate of reaction and the danger of the

Jan 1, 1968

General discussion on the above subject, presented at the Pittsburgh meeting, October, 1914. GEORGE S. Rice, Pittsburgh,. Pa.-Undoubtedly there is a serious problem through the juxtaposition of gas and oil wells and coal mines, not only at the present time, but possibly of far more serious import for the future. If one examines a map of the coal fields on which is superposed the oil and gas fields of the country, one finds that they overlap to a very great extent. I may say at the beginning that we have not, so far as I know, had any very large number, of accidents growing out of this situation causing loss of life. Such accidents, or rather incidents, that have occurred have all been rather potential possibilities for disasters due to the leakage of gas from wells into the adjacent coal mines. The condition has been most acute in the Fairmont district of West Virginia, and in the general coal fields southwest of Pittsburgh in Pennsylvania. The accidents which have actually occurred were summarized in Bulletin No. 65 (Oil and Gas Wells through Workable Coal Beds) issued by the U. S. Bureau of Mines, reporting the transactions of several meetings in Pittsburgh, February, 1913, of oil and gas well representives, State geologists, State mine inspectors, coal-mine operators, and representatives of the U. S. Bureau of Mines. This conference was partly brought about through a case in which the Pennsylvania State inspection department had brought suit to restrain a gas company from completing a well through a certain mine. The office of the Attorney General of Pennsylvania asked the opinion of the Bureau of Mines upon the matter; about the same time the Association of State Geologists, at its New Haven meeting, asked the Bureau to take up the problem. Accordingly, it was thought advisable to bring together the several, interests. For the most part the danger is, I think, greater in the future, than at the present time Many parts of the coal fields of Pennsylvania, in Greene County particularly, have been penetrated by numerous wells very close together, and with the present practice of having a large coal pillar around each well, has made or will make the mining of many areas difficult or pro-

Jan 4, 1915

By J. H. Klepinger, C. W. Goodale

I. Introduction....................567 II. Character oF the OrE................568 III. Old FluE System..................572 IV. Tests on Old FLUE System..............575 1. Aspiration Tests................. 575 2. Tests with Steel Settling Chamber........... 575 3. Test with Experimental Brick Flue........... 583 4. Testa on Blast Furnace Geses............. 591 V. Design of New FluE System.............. 597 VI. Main Dust Chamber................. 605 VII. Some DetailS of Construction ............. 609 VIII. THE Chimney.................... 616 IX. Operation of New FluE System............. 624 X. Temperatures and DraFTS............... 630 XI. Velocities and Volumes................ 632 XII. TeStS on the New FluE System............. 637 XIII. Conclusion..................... 643 I. Introduction. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and as this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 1, 1914

By B. F. Buie

Included in the general category of clays is a large and varied assemblage of nonmetallic silicate minerals which characteristically occur as fine-grained particles having flaky, sheetlike, or rod-shaped form. Most, though not all, are hydrous aluminum silicates. Amount and kind of impurities vary greatly, and these strongly influence the uses of the various clay types. Clays occur in a wide range of geological situations: as bedded sedimentary deposits composed of the weathering products of feldspar and other minerals; as alteration products of igneous, sedimentary, and metamorphic rocks weathered or hydrothermally altered in place; and, to a more limited extent, as hydrothermally introduced materials. TYPES AND MARKETS On the basis of chemical composition and crystal structure, two major groups of clay minerals recognized are the "kandites" or kaolin group, and the "smectites" or montmorillonite group. Another major type is illite, particularly important as a constituent of shales. Two additional mineral species having economic importance are attapulgite (palygorskite) and sepiolite. For present purposes, however, a classification based on utilization is more appropriate. The U.S. Bureau of Mines recognizes six types of clay: kaolin, ball clay, fire clay, bentonite, fuller's earth, and miscellaneous clay. Kaolin The kaolin group of minerals consists of the mineral species kaolinite, halloysite (metahalloysite), dickite, and nacrite, although the latter two are not being produced commercially. Kaolin, also called china clay, is a high-purity white material. Perhaps it is best known as a principal ingredient in the manufacture of chinaware, porcelain, and other high-quality ceramic products. However, by the mid-1970s very close to 50% of the kaolin produced in the United States was going to the paper industry for use as a filler and coating material. Manufacture of refractories uses about 12% of U.S. production. Kaolin is also used in plastics, in the rubber industry as a filler in footwear, electrical cable, and similar products, and as a conditioner of rubber for automobile tires to add strength and abrasion resistance. Smaller amounts are used in printing ink, paint, and adhesives; as insecticide carriers; in the production of catalysts for the petroleum refining industry; and in many other industrial and commercial applications. Production and use of kaolin in the United States doubled in the ten years from 1946 to 1956, and doubled again by 1966. Growth continues at a rate of about 7 % per annum.

Jan 1, 1976

The John Fritz Medal is awarded from time to time for notable scientific or industrial achievement by a board composed of representatives from the four engineering Societies. The members of the Board of Award for 1917 are: A. S. C. E. A. S. M. E. George F. Swain Ambrose Swasey, Charles Warren hunt, John, A. Brashear, Charles D. Marx, Frederick R. Hutton, Clemens Herschel. John R. Freeman. A. I. M. E. A. I. E. E. Gybbon Spilsbury, C. 0. Mailloux, Charles F. Rand , Paul M. Lincoln, Christopher R. Corning, John J. Carty, Benjamin B. Thayer. Harold W. Buck. The John Fritz Medal was awarded in January, 1917, to Dr. Henry Marion Howe, for his "investigations in metallurgy, especially in the metallography of Iron and Steel." The presentation ceremonies were held in the Auditorium of the United Engineering Societies' Building, New York, on Thursday evening, May 10. Mr. Ambrose Swasey, Chairman of the John Fritz Medal Board of Award, presided, and addresses were delivered by Dr. Rossiter W. Raymond, Secretary Emeritus of the American Institute of Mining Engineers, and Dr. Ira N. Hollis, President of the American Society of Mechanical Engineers. Professor Albert Sauveur, Chairman of the Board at the time the award was made, presented the medal, and the ceremonies concluded with the response of Dr. Howe.

Jan 7, 1917

The first session of the Institute was held at the Smithsonian Institution, on Tuesday evening, February 22d. The members were welcomed to Washington and to the Smithsonian by Prof. Joseph Henry. President Holley responded to the cordial welcome of Professor Henry, and then read an introductory address on the subject of Technical Education. Following the discussion on President Holley's address the following persons, duly proposed and indorsed by the Council, were elected members and associates of the Institute : MEMBERS. Emile R. Abadie,. .. .. St. Louis, Mo. R. J. Anderson,.....Pittsburgh, Pa. Commander L. A. Beardslee,. .. Washington, D. O, Charles Bender,. .. .. New York City. Charming M. Bolton,. .. . Richmond, Va. Thomas E. Bowman,. .. . Silverton, Colorado. Calvin E. Brodhead,. .. . Bethlehem, Pa. M. L. Brosius,. .. .. . Lewistown, Pa. Harvey H. Brown,. .. .. Cleveland, Ohio. James A. Burden,.. .. . Troy, N. Y. J. P. Clemes,. .. .. . Sonora, Mexico. N. H. Cone,. .. .. . Nederland, Colorado. W. F. Durfee,.. .. . New York City. Robert Frazer, Jr.,. .. . Ashland, Pa, Joseph E. Galigher,.. .. . Bingham, Utah. William Golding,.. .. . Steel Works P. O, Pa. Samuel E. Griscom,.. .. . Pottsville, Pa. Gen. E. Burd Grubb,.. .. Beverly, N. J, Arthur R. Guerard,. .. .. Charleston, S. C. Edward Hart,.. .. .. Easton, Pa. Prof. Lewis M. Haupt,. .. . Philadelphia. E. S. Hawley,.....Buffalo, N. Y. John W. Hoffman,.. .. .. Philadelphia. Nelson P. Hulst,.. .. . Milwaukee, Wis. H. C. Humphrey,.. .. . Philadelphia. Ed. P. Jennings,.. .. .Ithaca, N. Y. B. F. Jones,......Pittsburgh, Pa.

THE first session of the Institute was held at the Smithsonian Institution, on Tuesday evening, February 22d. The members were welcomed to Washington and to the Smithsonian by Prof. Joseph Henry. President Holley responded to the cordial welcome of Professor Henry, and then read an introductory address on the subject of Technical Education. Following the discussion on President Holley's address the following persons, duly proposed and indorsed by the Council, were elected members and associates of the Institute : MEMBERS. Emile R. Abadie, - St. Louis, Ma. R. J. Anderson, - Pittsburgh, Pa. Commander L. A. Beardslee, - Washington, D. C. Charles Bender, - New York City. Channing M. Bolton, - Richmond, Va. Thomas E. Bowman, - Silverton, Colorado. Calvin E. Brodhead, - Bethlehem, Pa. M. L. Brosius, - Lewistown, Pa. Harvey H. Brown, - Cleveland, Ohio. James A. Burden, - Troy, N. Y. J. P. Clemes, - Sonora, Mexico. N. H. Cone, - Nederland, Colorado. W. F. Durfee, - New York City. Robert Frazer, Jr., - Ashland, Pa. Joseph E. Galigher, - Bingham, Utah. William Golding, - Steel Works P. O., Pa. Samuel E. Griscom, - Pottsville, Pa. Gen. E. Burd Grubb, - Beverly, N. J. Arthur R. Guerard, - Charleston, S. C. Edward Hart, - Easton, Pa. Prof. Lewis M. Haupt, - Philadelphia. . R. S. Hawley, - Buffalo, N.Y. John W. Hoffman, - Philadelphia. Nelson P. Hulst, - Milwaukee, Wis. H. C. Humphrey, - Philadelphia. Ed. P. Jennings, - Ithaca, N. Y. B. F. Jones, - Pittsburgh, Pa.

Jan 1, 1876

The United States has never been a large coal exporting nation, and normally such shipments, aside from those to Canada, have been relatively small. Since the first railroad was built across the Allegheny Mountains, the imports have been quite small also, although fairly large tonnages of Canadian coal have moved into the extreme northeastern and northwestern states at times. In Table 21 are shown all data available about these shipments from 1790 to 1939, inclusive.

Jan 1, 1942

By M. D. Hassialis

[Surface Areas of Concentrates and Collector Coatings (T.P. 2002, by A. M. GAUDIN and G. S. PRELLER, Min. Tech., May. Discussion by M. D. HASSIALIS and the authors) . I Activation of Minerals and Adsorption of Collectors (T.P. 2082 by J. ROGERS and K. 1'. SUTHERLAND, Min. Tech., Nov. Discussion by A. F. TAGGART and the authors). . . . 3 Correlation between Mineral Behavior in Cataphoresis and in Flotation (T.P. 2005 by A. If. GAUDIN and S. C. SUN, Min. Tech., May. Discussion by M. D. HASSIALIS). . . . . . 8] Surface Areas of Concentrates and Collector Coatings M. D. HASSIALIS.*-In the current flotation theories there exists a common gap spanned by a common assumption pertaining to the arrangement and orientation of the collector ions at the solid surface. Also common is the belief that contact angle and flotation performance are dependent upon the arrangement and orientation of collector ions. This stimulating and informative paper sheds some light upon this general problem. One of the indices of arrangement is the area available per collector ion; in this connection, Gaudin and Preller have applied the B.E.T. method for surface determinations. In a surprising number of cases, their results show a greater specific surface for tailing than for concentrate. This cannot be accounted for by the differences in specific gravity and is attributed to the presence of clay minerals of "primary" sluices in the tailing. This is not a satisfactory explanation, for experience shows that when free slimed clay minerals are present in a flotation cell they will be carried mechanically into the concentrate. A part of the answer to the decreased specific surface of the concentrate would appear to be its usual flocculated condition, yet this should not entirely account for the large spreads reported. The possibility occurs that the nitrogen adsorption isotherms for clean mineral and collector-coated mineral are different. If that were true, and if the coated mineral surface exhibited decreased adsorptive powers, the discrepancy might vanish. In discussing the disposition of collector ions at mineral surfaces, the authors adopt the more consistent viewpoint that there exists some agreement between the ions of the substrate and those of the superstrate. In the case of xanthate ions on galena, a possible arrangement is shown in Fig. 2. This arrangement shows every xanthate ion being shared by two lead ions, whereas the chemical composition calls for two xanthate ions for each lead ion (p. g). This whole discussion is misleading. In the first place, it is known that xanthate ions are not abstracted by unoxidized galena, hence Fig. 2 should show as the substrate not Pbs but PbS„ Om. It would be equally erroneous to use the lattice arrangement of PGSO4, since the surface properties of xanthate-conditioned anglesite differ from those of xanthated galena. It is highly probable that the state of the galena surface exploited in its flotation is ephemeral, since weathered galena is only poorly, if at all, collected by xanthate. Just how a substrate of oxidized galena is to be pictured depends upon one's conception of the transformation from galena to anglesite. This writer is inclined to the following sequence of events. Surface sulphide ions undergo progressive oxidation. As more oxygen is taken up by the sulphide ions they become displaced from their equilibrium positions in the galena lattice, thus accommodating for the larger volume of the S„ Om ions. Concomittant with this change the forces acting on the lead ions

Jan 1, 1946

Robe River is ready to go. After seven years of extensive drilling, sampling, pilot plant studies, negotiations with Japan and Australia and agonizing ups-and-downs in financing, this $300 million iron ore project in Western Australia is all set to rush project development to the production stage. Preliminary engineering completed, the combined efforts of Japanese, U.S. and Australian mining concerns will proceed with construction of the project's mining, processing, pelletizing and shipping facilities.

Jan 1, 1970

The following is a, partial list of members and guests who called at Institute headquarters during the period Aug. 10, 1917, to Sept. 10, 1917. L. P. Barrett, Ann Arbor, Mich. Milo W. Krejci, Great Falls, Mont. H. J. Brown, Ridley Park, Pa. Chas. N. La Porte, Peoria, Ill. George M. Cheney, Guayaquil, Ecuador. Askin Nicholas, Bismuth, Australia. W. Lorrain Cook, Chicago, Ill. C. Edwin Nighman, Butte, Mont. John J. Croston, Atlanta, Ga. W. L. Remick, Norfolk, Va. A. F. Duggleby, Santiago de Cuba. T. C. Roberts, Jerome, Ariz. Geo. A. Easley, La Paz, Bolivia. Burr A. Robinson, New Haven, Conn. Burr J. French, Magdalena, Jal., Mex. J. L. Schueler, Peoria, Ill. A. D. R. Galloway, Komfrodua, W. Af. Walter L. Steele, Van Horn, Tex. P. R. Hines, Milwaukee, Wis. F. J. S. Sur, Denver, Colo. T. H. Jenks, Wickenburg, Ariz. C. A. Thomas, Dawson, Y. T., Canada. Paul S. King, Wilmington, Del. E. E. White, Ann Arbor, Mich. Harry Wolf, Golden, Colo. L. W. Bahney has left the Sheffield Scientific School, Yale, to become metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn. H. B. Barling, formerly chief engineer of Breitung & Co., of New York, has been appointed manager of the mining department.

Jan 10, 1917