Search Documents

By N. A. Gokcen, J. Chipman

Aluminum and oxygen dissolved in liquid iron were brought into equilibrium with pure alumina crucibles and atmospheres of known H2O and H2 contents to study the reactions: 1—Al2O3(s) = 2 Al + 3 0; 2—Al2o3(s) + 3H2(g) = 2Al+ 3H2o(g); and 3—H2(9) +O = H2O(g). Aluminum strongly reduces the activity coefficient of oxygen and similarly oxygen reduces that of aluminum. Values of the product [% All" • [% O]3 are much smaller than those found in previous experimental studies and are of the order of magnitude of the calculated values. ALUMINUM is the strongest deoxidizer commonly A used in steelmaking, but the extent to which it removes dissolved oxygen has been debatable. The relationship between aluminum and oxygen has not been determined reliably not only on account of the usual experimental difficulties at high temperatures but also because of uncertainties in the analyses of very small concentrations of oxygen and aluminum. The earliest experimental attempt of Herty and coworkers' was followed by a more systematic study of Wentrup and Hieber.' These authors added aluminum to liquid iron of high oxygen content in an induction furnace and considered that 10 min was sufficient to remove the deoxidation products from the melt. Parts of the melts thus obtained were poured into a copper mold and analyzed for total aluminum and oxygen (soluble plus insoluble forms), assuming that the insoluble parts were in solution at the temperatures from which samples were taken. It is conceivable that the furnace atmosphere in their experiments, consisting of mainly air at 20 mm Hg pressure, was a serious source of continuous oxidation and therefore that their oxygen concentrations were correspondingly high. Scattering of their data was explained to be well within the maximum inaccuracy of 10°C in the temperature measurements and errors of ±0.002 pct each in the oxygen and total aluminum analyses. Maximum and minimum deoxidation values, i.e., values of the product [% All' . [% O] differed by factors of 10 to 15; mean values of 9x10-11 and 7.5x10-9 ere reported at 1600" and 1700°C, respectively. Hilty and Craftsv determined the solubility of oxygen in liquid iron containing aluminum, using a rotating induction furnace. Pure alumina crucibles used in their experiments contained the liquid iron which in turn acted as a container for slags of varying compositions consisting mainly of Al2O3, Fe2O3, and FeO. The furnace was continuously flushed with argon, and additions of aluminum and Fe2O3 were made in the course of each experimental heat. The inner surfaces of their alumina crucibles were covered with a substance other than pure Al2O3, containing both iron oxide and alumina. Although frequent slag additions can change the composition of slag in the liquid iron cup formed by rotation, the inner surface of the crucible must depend upon the transfer of oxygen or aluminum through the liquid iron for any adjustment in composition. It is not clear that their metal was in equilibrium with the crucible wall, but it is clear that it was not in equilibrium with Al2O3. Their deoxidation product, [% A].]" • [% O]3, varied by a factor of more than 50; the average values of 2.8x10- and 1.0x10-7 were selected for temperatures of 1600" and 1700°C, respectively. Aside from the experimental determinations, attempts have been made to calculate the deoxidation constant for aluminum indirectly from thermody-namic data. Schenck4 combined the thermodynamic data for Al2O3 and dissolved oxygen in liquid iron by assuming an ideal solution. His calculated values are 2.0x10-15 and 3.2x10-13 at 1600" and 1700°C, respectively. Later, Chipman5 attempted to correct for the deviation from ideality and derived an expression which led to deoxidation values of 2.0x10-14 and 1.1x10-12 at 1600" and 1700°C, respectively. The errors in these treatments originate mainly from inaccuracies of thermal data and uncertainties regarding the activity coefficients of dissolved oxygen and aluminum. The purpose of this investigation was to study the equilibria represented in the following reactions in the presence of pure alumina: Al2O3(s) = 2Al + 3O K = aAl2.ao3 [1] Al2O3(s) + 3H2(g) = 2Al + 3H2O(g) H2O K2 = aAl2(H2O/H2 ) [2] H2(g) +O = H2O(g) K3 = 1/ao (H2) [3] The experimental method consisted of melting pure electrolytic iron, usually with an initial charge of aluminum, in pure dense alumina crucibles under a controlled atmosphere of H,O and H2 and holding

Jan 1, 1954

By Jim V. Rouse

There have been many changes in environmental control techniques since the early days of uranium mining and milling, when liquid mill effluents and often mill tailings were discharged directly into nearby streams. With today's stringent environmental controls, the uranium miner must be as aware of regulatory requirements as he is of techniques in mining, milling, and in-situ recovery. The time delays involved in bringing a uranium project on line dictate that the proposed facility be designed with a view not only of present regulations, but also of those which may be in effect when the facility is completed. While such predictions are difficult, it's almost certain that regulatory agencies will exercise even more environmental control over future uranium mining and milling operations, using the past errors of the 1950's as justification for increasingly stringent controls.

Jan 10, 1978

By H. Sigurdson, C. H. Moore

Extensive studies have been carried out on electric furnace and blast furnace slags obtained in the winning of iron from its ores. These slags normally consist of elements of the gangue minerals present in the ores, as well as the added flux materials. In consequence, melts of CaO, MgO, Al2O3 and SiO2 can be considered as representing typical slag compositions. When a slag of this composition cools, it usually crystallizes according to predictions possible from an equilibrium diagram of these constituents, providing the melt is not undercooled to form glass. The melt is either viscous or fluid, depending upon the ratio of binary cations to silica, and crystallizes easily or forms a glass for the same reasons. If the melt is not overheated so that carbides of the metal components of the slag are formed and if the composition of the slag is so adjusted that it has a high fluidity, liquid equilibrium is attained and the slag can be held in a liquid state for extended periods of time. Upon tapping, the slag crystallizes into minerals, the type and proportion of which are determined by the melt composition. Since equilibrium is attained, the holding period is not critical. In melts containing a large increment of titanium, however, the normal slag procedures are not applicable. Titanium, as one of the atomic transition elements, is, at elevated temperatures, capable of being reduced to form metalloid compounds much more readily than the refractory oxides present in normal slags. In consequence, an oxide melt containing titanium never reaches equilibrium in a reducing environment, but continues to shift its composition until cooled. If melts of this nature are cooled and samples submitted to metal-lographic and X ray analysis the course of reaction and crystallization in this type of slag can be determined. Preparation of Slag The slags investigated fell into the system CaO-MgO-TiO2-Al2O3-SiO2 and were produced from ilmenite ores reduced by carbon in an electric furnace. Since the equilibrium series1 and the laboratory smelting of ilmenite2 are described in two of the accompanying papers, detailed description of the smelting procedure is not required here. However, certain essentials must be mentioned. Two types of melts were used to produce slags studied in this investigation. The first series of smelts made to determine proper flux addition were produced in a 4 lb Ajax induction furnace. The charge, consisting of ore with the proper flux addition, was heated in a graphite crucible until fluid, held fluid for a sufficient time period to obtain 1-5 pct FeO content, and poured. Because of the small size of the charge only the final sample of these melts could be examined. In the melts made in the 50 lb arc furnace, however, grab samples taken at 10 min. intervals between time of initial melting and final pouring were available for examination. These samples allowed a much clearer picture of the course of reaction and crystallization. amounts of ferrous oxide and reduced titanium compounds is opaque to transmitted light. Therefore, all petro-graphic studies had to be made on polished slag sections. A representative sample of slag was cut or broken, mounted in a thermosetting plastic, ground flat using 400 grit silicon carbide, the coarse scratches removed with 600 grit silicon carbide and polished on billiard cloth using levigated alumina. Rouge was avoided because of the entrainment of the red particles in pores in the slag, causing a possible confusion with some of the mineral phases. In order to prevent sample projection above the plastic surface red bakelite was used to hold the sample, and backed up with clear lucite. In this manner sample labels could be permanently retained in the mounting. The polished samples were examined on a Bausch and Lomb metallograph at magnifications of 250 X, 500 X, 1000 X and 1800 X. The instrument was equipped for examination of specimens under bright field illumination and with crossed nicols. A magenta tint plate to aid in color tone differentiation was also used. Petrology of Slags In order to determine the composition and mineral relatinos of a previously unreported system petrologically, it is essential that the starting composition, reaction temperature and final composition be known. The chemical composition of the ilmenite ore used in these smelts is given in Table 1, and the complete analysis of a typical high titanium, low iron slag is given in Table 2. In the winning of TiO2 from ilmenite by a smelting process it is necessary to produce a slag which will melt at an economically feasible temperature, remain molten as the iron is removed by reduction, be fluid enough to be readily removed from the furnace, contain a high percentage of TiO2 and a low percentage of reduced titanium com-

Jan 1, 1950

By Peter Nalle

12.3-1. Reporting. NEED. It seems almost unnecessary to comment on the need for reporting research and development results and activities, and yet much of the difficulty and misunderstanding surrounding a Research and Development (R&D) group results from poor or nonexistent reporting. Certainly no evaluation can be made without reports of results or plans. It is as important to report accurately and fully for the department's own use as it is for external use. Research unreported might as well be considered research undone. This section will discuss, in part, the need for reporting, the general types of reports which may be generated to satisfy the need, and finally, the evaluation of a project as judged by various commonly used standards. PURPOSE. Some specific observations might be appropriate concerning the reporting of R&D results. The requirements and background of the group receiving the report must be considered. A particular report is usually directed towards the background of a particular group, such as ((technical," "operational," "financial," or "marketing." It is essential that the emphasis and coverage be geared to the training of people receiving the report. It should be obvious that the financial department will be less interested in the technical details of the process and more interested in the capital funds and tax implications involved in the project. Operating personnel will be greatly interested in the effects of a new method on mining plans, and so on. This does not mean that the reporting in any way should slight pertinent details, nor should a patronizing attitude be assumed by the writer. However, it is essential that the needs of the reader be recognized. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. A

Jan 1, 1968

By T. H. Weldon, L. V. Whiton, R. R. McNaughton, J. H. Hargrave

Oxygen enriched air is being used quite extensively in the metallurgical plants of The Consolidated Mining and Smelting Co. of Canada, Limited, at Trail, B.C. The oxygen used for this purpose is a by-product from the Company's chemical plants located in the area. Most of the ore treated in the Trail metallurgical plants comes from Com-inco's Sullivan Mine at Kimberley, B.C. At Kimberley the ore is milled to produce lead and zinc concentrates which are shipped to Trail for further treatment to metal. One section of this paper deals with the use of oxygen enriched air in the suspension roasting of the zinc concentrates. In this process the concentrate is calcined for leaching preparatory to electrolytic recovery of the zinc. A second section of the paper describes the use of oxygen enriched air in operations at the lead smelter. There oxygen enriched air is used in the blast to the lead blast furnaces and in the slag fuming furnace which recovers the lead and zinc contained in lead blast furnace slag. The final section of the paper outlines the precautions necessary for the safe use of oxygen enriched air in any plant operation. The Use of Oxygen Enriched Air in the Suspension Zinc Roasters The suspension roasting of zinc concentrate developed at Trail, B.C., has been described in AIME Vol. 121, "The Electrolytic Zinc Plant of The Consolidated Mining and Smelting Company of Canada, Limited" by B. A. Stimmel, W. 11. Hannay and K. D. McBean. Since the publication of that paper, the use of oxygen enriched air in suspension roasting has been introduced as regular practice with marked advantage. The relative importance of a specific advantage may vary with changing conditions, but, in general, it may be stated that improved operation has been achieved at increased capacities. Suspension roasting is carried out at Trail in converted standard 25 ft diam Wedge roasters. The 2nd, 3rd, 4th and 5th roasting hearths have been removed and the drying hearth covered over. Drying of the concentrate is done on the drying hearth and the 1st roasting hearth. The dried concentrate, after any lump's have been broken up in a ball mill, is fed to a single burner located in the upper part of the combustion chamber. Oxygen is introduced at the burner fan along with the gases from drying, returned combustion gases from the waste heat boiler outlet and the required amount of new air. Up to 60 pct of the concentrate settles out on the 6th roasting hearth, the rest passilig out of the roaster. The product collected in the waste heat boiler is finished calcine, but the dust collected in the cyclones after the boilers is returned to the base of the combustion chamber where the sulphate is decomposed. Gases from the c'yclones go to a Cottrell precipitator. The discharges from the 7th roasting hearth and the waste heat boiler are combined with the Cottrell dust to give the finished calcine. Following small scale tests started in 1933, oxygen enriched air has been used continuously in the suspension roasting of zinc concentrate in Trail, beginning in 1937. A significant factor in promoting its use in this operation was the availability of by-product oxygen from the Company's near-by Chemical and Fertilizer Division. To-day it is standard practice at Trail to use oxygen enriched air for zinc concentrate roasting. The most important requirement in roasting a zinc concentrate for an electrolytic plant is that the zinc in the calcine should have maximum solubility. It is also desirable at Trail that the gas produced for the manufacture of suhhuric acid should have a ~naximum concentration of SO2 and that a substantial recovery of waste heat from the gas be achieved. High solubility of zinc requires that the sulphide sulphur and zinc ferrite in the calcine be kept low. These are both functions of temperature and time, with formation of zinc ferrite also dependent on contact between the iron and zinc particles. One of the inherent advantages of suspension roasting is that minimum time and contact are achieved. The limit on temperature is imposed by the fusion point of the concentrate and not by the need to control zinc ferrite formation. Operating temperatures are normally maintained within the limits of 1725" and 1850°F. A relatively low zinc sulphate in the calcine is required at Trail, and this results from discharging the calcine from the high sulphur dioxide atmosphere at a temperature above 1600°F.

Jan 1, 1950

By J. Donovan Jacobs

An underground excavation project usually is a highly organized complex of different but interrelated construction activities. It is the whole effort, including the necessary tools, which will be referred to as the System. Tunnel-driving and shaft-sinking operations are among the most systematic of construction efforts. Systems are not new in the performance of construction. It is the Systems Concept which seems only recently to have been discovered and made the subject of much study and discussion. HISTORICAL From the seventeenth century, when explosives were first utilized for rock excavation, until the successful application of the rotary-head continuous tunneler in this decade, the cyclical drill-blast-muck-support method has been standard tunnel-driving procedure throughout the world. Whatever improvements occurred were the result of development of better tools for performing the various operations of the cycle. The electric locomotive replaced the mule and permitted the use of larger muck cars. The steam drill, which ended the day of the double jack, was itself quickly made obsolete when compressed air replaced steam as the source of drilling energy. Power shovels were introduced to save the time and money involved in the hand-loading of excavated materials. A cubic yard of rock tunnel muck can be excavated today for just half the man-hours of labor required in 1948. Developments over 20 years which cumulatively have resulted in this economy include: drifter drills mounted on hydraulically controlled booms and positioners; tungsten-car- bide-tipped bits; long feed shells on the drifters, making it possible to drill the full depth of a round without changing steel; better designed,

Jan 1, 1970

By John B. Pearse

IN view of the great importance of accurate knowledge respecting the chemistry of iron and steel, as related to their physical properties, I come before you with a paper showing the great mass of work which has been heretofore done on the subject. I have tabulated the more important data I bring at this time, so as to draw out the results clearly. This information is accessible to all who will seek for it. I have made it the basis of my own practice throughout, and such knowledge is undoubtedly the only foundation, for the successful practice of metallurgy. As is well known the ordnance corps of our army, after 1841, made exhaustive experiments on the properties of cast-iron. The investigations were undertaken in order to obtain necessary information on the reorganization of the corps. I wish to call your attention to the results obtained by a comparison of the chemical and physical properties of cast-iron for guns, to describe certain characteristic peculiarities of steel, and to give a brief history of the chemical work relating to carbon in iron. The Reports on Experiments on the Strength and other Properties of Metals for Cannon, published by H. Carey Baird, Philadelphia,

Jan 1, 1876

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By W. H. Eardley

IT IS increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh-that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed .them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. FLOTATION PRODUCTS RECEIVED At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent. lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent. moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent. moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain-nodules and balls of unroasted concentrates, sulfur elimination

Jan 1, 1928

By A. B. Young

The difficulties encountered in the preparation of the lead smelter charge for the blast furnace and in the roasting and sintering of the ores, and the expert means taken for the preparation of these materials since the introduction of flotation concentrates into the lead smelter charge, have been described by W. H. Eardleyl and R. A. Wagstaff.² Function of Roasters and Blast Furnaces The lead smelter has first its roasters and its sintering devices, of which the primary object is the removal of sulfur from the ore or from the charge. The blast furnace follows; its function being the elimination of the gangue material left in the charge—the elimination of the insoluble, the iron, the zinc and the lime from the metallic lead. The secondary object is the separation of copper from the lead. A lead blast furnace is a sensitive apparatus. The materials composing the charge must be marshalled in certain proportions before they will make a fluid slag which will separate from the metallic lead. The silica, iron, lime and zinc must be put together in proportions that usually do not mist naturally in the ores, therefore fluxes are necessary. Function of the Flotation Cell The flotation cell—-speaking from the standpoint of a lead concentrate—has taken over part of the work hitherto performed entirely by either gravity concentration or the lead blast furnace. It has eliminated gangue from the concentrate and separated waste products from the lead. In so far as it has done that, it has usurped some of the function of the lead blast furnace; and it is much cheaper to run a flotation cell than a lead blast furnace. The effect in Utah, and it will be similar to effects in other districts. has been to remove a great deal of the gangue by means of flotation, whereas in the old clays it was eliminated by means of sme1ting. In this district, as in others, the insoluble content of the ores has been greatly out of proportion to the iron and lime content to make a proper slag

Jan 1, 1928

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the GEORGIA PRODUCTION UNITED STATES PRODUCTION IMPORTS Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937

Jan 1, 1931

By James M. Barker

Jan 1, 1985

By D. F. Atkins, B. A. Rogers, E. J. Manthos, M. E. Kirkpatrick

A phase diagram of the uranium-columbium alloys is presented. The apparatus and the procedures used in obtaining the data are described. Data from which the diagram was drawn are given in tabular and graphic form. THE use of uranium in the production of energy from nuclear fission has given considerable im- petus to the investigation of the metal and its alloys. Accordingly, information concerning the phase diagrams of binary alloys of uranium with other elements is of interest to metallurgists engaged in nuclear-engineering activities. As a contribution to the knowledge of the binary alloys, the authors have attempted to establish the diagram of the uranium-columbium system. The reports of laboratories engaged in work for the Manhattan Engineering District and the U. S. Atomic Energy Commission contain a number of references to work on uranium-columbium alloys.

Jan 1, 1959

By R. E. Pollard

The National Bureau of Standards received, in August 1940, a number of samples of bridge wire taken from the cables of the General U. S. Grant suspension bridge over the Ohio River at Ports- mouth, Ohio. These cables were 7% in. in diameter under the wrapping and each was made up of 1458 ungalvanized wires of No. 8 gage in 3 parallel-wire strands. The choice of ungalvanized wire was based on the previous satisfactory performance of similar wires in other bridges over periods of 20 to 50 yr. of service(1).2 After about 12 yr. of service a number of breaks were discovered in the Portsmouth bridge cables, most of them at the anchor- age shoes, and they were replaced by cables made up of galvanized wire(2).

Jan 1, 1945

Jan 1, 1935

Jan 1, 1943

A. A. Almstrom is mill superintendent for Barrue Mines, Barraute, Quebec. Frank A. Ayer, vice president of Copper Range Co., who has been in charge of the development and bringing into production of White Pine orebody in northern Michigan, has resigned. E. G. Bailey and H. S. Mudd were made honorary members of the American Society of Civil Engineers. Lee Bilheimer, graduate of Missouri School of Mines, has been employed as assistant mine captain at the Edwards, N. Y., div. of the St. Joseph Lead Co. Douglas C. Blackwell, recently graduated from the South Dakota School of Mines, is now with the Oliver Iron Mining Co. of Duluth, Minn. Joseph F. Brown has joined the Grand Junction Exploration Branch of the United States Atomic Energy Commission as a geologist.

Jan 1, 1952

By Helen L. Cannon

BOTANICAL methods of prospecting for metalliferous ores are based on the premise that deposits at depth may be reflected chemically in surface vegetation. For the past several years, on behalf of the Atomic Energy Commission, the U. S. Geological Survey has investigated on the Colorado Plateau the application of botanical methods to uranium prospecting. Results suggest that orebodies may be found under a considerable cover of barren sandstone through the absorption of uranium and associated trace elements by plants growing at the ground surface. Plant physiologists have demonstrated that uranium is a necessary nutrient for plant growth and therefore is present in all plants.' The amount present is small but measurable. The absorption of uranium by plants growing over ore deposits forms the basis, therefore, for a method of prospecting by plant analysis.

Jan 2, 1954

By Fred P. Dewey

In my paper on the porosity and specific gravity of coke, read at the Roanoke meeting, June, 1883, and published in this volnme, an analysis by Dr. henry Froehling is reported (p. 10 of the preliminary edition of the paper, or p. 120 of this volume), as showing the composition of Fire Creek coke. This analysis WaS of coke made in beehive ovens at Low Moor, Va., from New River coal. Dr. Froehlng's analysis of the Fire Creek coke was as follows: Moisture..........0.260 Volatile matter.........0.260 Fixed carbon .........92.377 Ash 1....6.750 Sulphur..........0.535 Phosphorus.........0.0146 Both analyses are reported side by side in The Erginias for 1883, p. 99. By an error in copying, the Low Moor analysis was trans-

Jan 1, 1884