Search Documents

By Calvin Pierson, R. S. Dean, E. P. Barrett

MANY studies have been made of the properties of steel produced by adding varying amounts of sponge iron to the charges used in steelmaking furnaces.1-3 The results of these previous studies, however, have failed to disclose a reason for the belief of steelmakers that steel made in this way is definitely different from steel made entirely from scrap or iron melting stock. This paper deals chiefly with the structure of the sponge iron, of the wrought iron made by welding the sponge iron into blooms, and of the steel made by melting the forged and rolled blooms. It is believed that the structure of the final steel is inherited from the ore and that this inherited structure produces marked differences in the properties of the steel and explains the feeling of steelmakers which is based on their experience. Three kinds of sponge iron were used in this investigation: One made from a limonite ore reduced with natural gas, one made from a hematite ore reduced with natural gas, and one made from a magnetite ore reduced with charcoal. The sponge iron made by reduction with natural gas

Jan 1, 1935

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By H. S. Kalish, F. J. Dunkerley

INTRODUCTION AND PREVIOUS WORK THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low temperature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pct lead were measured at eleven temperatures from -196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the 'extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature mbrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. Cohen and van Lieshout1 have established the beta to alpha tin transformation at 13.2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin-rich phase will occur in a short-time tensile test. Polanyi and Schmid2 studied the tensile . properties of tin single crystals at -185°C and report that tin is brittle at-this temperature. In 1946, Kostenets3 reported that pure tin was brittle at -196 and -253°C, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pct lead at -253, -196 and +17°C. The ultimate tensile strength increased more than two times in going from room temperature to -196°C and about three times that value on further cooling to -253°C. All the alloys were brittle at -6°C except those containing more than 75 pct lead. Even at -253°C, the 75 pct lead alloy retained 36 pct elonga¬tion in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1948

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By T. Egleston

FOR a great part of the progress of the world we are indebted to the works of engineers. It is to them that we owe our means of rapid transportation, our canals, our railroads, our bridges, many of our automatic machines, and most of those appliances which, by facili tating or decreasing the amount of human labor to be expended and by utilizing the great forces of nature, have made the present progress of the world possible. Their education is a matter of momentous interest to the whole civilized world. I have, therefore, thought that some discussion of the theory upon which their education should be based would be of interest to this body, and have ventured a few reflections and suggestions upon the subject. The word education, in its original signification, meant the draw ing out of a man what there was in him. In our common schools the practical work of education consists in putting into the brain a larger number of facts than can be retained, which are consequently more or less understood and digested. It ordinarily consists simply of teaching a round of abstractions or facts which when not assim ilated are not only useless to the individual, but generate careless habits of thought and make more or less untruthful, unfaithful or unsuccessful men. In most of our schools a procrustean system is adopted; all are made to advance upon one general plan, the quick being kept back and the slow dragged on at a rate too great for their power of comprehension. Until within a very few years it has been a theory in common school education that the brain alone should be developed, and that little or no attention need be paid to the train-

Jan 1, 1888

By Ellis Clark

THE mining town of Pribram is situated in Central Bohemia, on the western slope of the Heiliger Berg, 30 miles southwest from Prague. Birkenberg, the village in which most of the shafts and ore-dressing establishments are situated, is built on a mountain of the same name. It is about a mile from Pribram, is 1700 feet above the sea, and is surrounded by graywacke rocks of Silurian origin, which are intersected by greenstone dikes, and in the southerly, southeasterly, and southwesterly direction are bounded by granite. The graywacke formations consist on one side of graywacke sandstone and quartzite, and on the other of graywacke slates. These last are separated from the first in the immediate vicinity of the mines by a graywacke seam converted into clay. For many years this so-cal led clay seam (lettenkkluft) was considered as a boundary of the ore deposits in both zones of graywacke. The graywacke formation is divided according to its hardness, structure, texture, and color, into fine, coarse, compact, slaty, whitish-gray, reddish-gray, and black graywacke. The, miner divides the formation into four divisions. The first or lowest division, which is in contact with the granite, consists of a fine-grained dirty gray slate; the -second is a very fine to a very coarse schist, white to reddish-gray in color, and rich in quartz, but containing little mica; the third consists of a slate with a contused cleavage, which has a dirty gray, dark gray, and very often black color and is often graphitic in its composition ; the fourth consists of a fine to coarse-grained graywacke schist, of a grayish-white or reddish-gray color, and rich in quartz. The cleavage in all four divisions strikes from northeast to southwest, and the dip is sometimes northwesterly, sometimes southerly, and often vertical. All four zones are cut through by a great number of diorite and greenstone dikes and chimneys. The thickness of these dikes, which are of

Jan 1, 1881

By J. Ralph Finlay

In latitude 4" S., about fifty miles from the Pacific, and in the amphitheater on the west flank of the Andes, which is drained by the river Tumbez, is the ancient town and mining district of Zaruma. The town is picturesque in the extreme, perched on a ridge 1800 feet high, between two lovely mountain rivers, looking out upon neighboring hills and valleys clothed in rich green, relieved by many hamlets roofed in red tiles, and, at greater distances on all sides, upon mountain slopes of gloomy forest crowned by the bare summits of the Andes. General Description. The gold-mines, discovered in 1549, mere worked extensively by the Spaniards in the 16th and 17th centuries, until their success was curtailed by the exhaustion of the oxidized surfaceores, and the uncovering of the refractory and hard ores underneath. The industry slowly declined until it was nearly or quite at a standstill in 1878, when an unfortunate English company, organized by Chilian promoters, acquired some of the best properties and began to work them. This company, after an extravagant début, relapsed into a struggle against poverty and mismanagement, and finally collapsed in 1894. In 1896 the English mines and many others, covering most of the district, were acquired by the South American co., formerly the South American Development Co., of New York. (See Figs. 1 and 2.) The vein-formation of Zaruma is extensive and complex, and the ores are somewhat refractory. In the immediate neighborhood of the gold-bearing veins the formation seems to be altogether volcanic, consisting of rather fine-grained holocrystalline diorite; but a few miles away, on either side, some gueisses and crystalline schists are to be found. About four miles south of the mines, and beyond some intervening granites, appear

Jan 1, 1901

By Richard Miller

WORK was undertaken two years ago at the Hammond Laboratory for the purpose of determining the magnitude of the elastic range in single crystals of pure metals by means of creep tests, the assumption being made that if a true elastic range exists, the elastic limit represents the maximum stress for no creep. A sensitive extensometer was constructed, and creep tests were made on zinc single crystals at a variety of loads and temperatures1. It was soon discovered that there is tip measurable elastic limit in ductile zinc single crystals at, or above, room temperature. The inference that pure metallic single crystals may not possess a definite elastic range was not justified, however, since zinc had been tested in creep only above its recrystallization temperature, and several investiga-tors2,3,4 had already shown that above the recrystallization temperature polycrystalline metals will flow under very small stresses, while below that temperature stresses of a much larger magnitude are required. For that reason, it was decided to extend the study of the elastic limit to other metals having a higher recrystallization temperature than zinc. Aluminum and silver were selected, because of the ease of obtaining pure materials and of preparing large single crystals, and because the crystallo-graphic glide system of these metals is well known. Owing to the limited time available, the elastic range was investigated by slow tensile tests rather than by creep tests.

Jan 1, 1937

By George Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable appara-tus, which can rapidly give a sufficiently reliable indication of the rela-tive dust hazard.

Jan 1, 1937

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By R. M. Brick, Arthur Phillips

The Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segregation. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute concentration, with a resultant normal segregation or coring effect during freezing. Theoretically, musion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions aluminum-copper alloys segregate inversely and aluminum-magnesium alloys segregate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By E. R. Gilbert

Klopp et al. have reported data on tensile and creep properties of are-melted and electron-beam-melted tungsten. We would like to point out some similarities between their creep results and ours on are-melted and powder-metallurgy tungstenand offer some alternate interpretations of the data which lead to different rate-controlling mechanisms. Klopp et al. observed extensive transient creep in the 2250" to 3500°F temperature range where the acthetivation energy is 106,400 ± 3300 cal mole-1. They suggest cross slip as the possible rate-controlling mechanism since "cross slip may occur only by the movement of screw dislocations, and not edge dislocations, thus allowing only partial recovery of the strain hardening and resulting in a continuously decreasing creep rate, characteristic of transient creep.'' Our tests on are-melted tungsten and powder-metallurgy tungsten displayed an extensive transient creep stage in the same temperature range but they also displayed a steady-state creep stage. The stress levels and strain rates of the two investigations, 1.4 to 7 kg mm-2 and 10-7 to 10-4 sec-1 for that of Klopp et al. and 4.5 to 10 kg mm-2 and 10-8 to 10-4 sec-1 for those of Gilbert et al., are overlapping. The activation energy for creep of our powder-metallurgy tungsten is 105,000 cal mole-1. This close agreement with the value found by Klopp et al. suggests that the same mechanism may be common to both types of materials. It may be possible to gain some additional insight into the rate-controlling mechanism by applying the analysis made by conrad22 in terms of the activation volume. The value for the activation volume depends upon the dislocation mechanism and may be used to help differentiate between various dislocation mechanisms. The activation volume for cross slip is 10 to 100 b3. Values determined from our data were 130 to 220 b3 which are in better agreement with the range of 102 to 104 b3 for nonconservative motion of jogs. Values determined from data of Klopp et al. are 240 to 1040 b3. We suggest that the rate-controlling mechanism for creep in this temperature range may be nonconservative motion of jogs assisted by enhanced diffusion along grain boundaries or dislocations. This model requires an activation energy lower than that for self-diffusion as is observed. If this is the controlling mechanism, a higher activation energy which is closer to that for self-diffusion might be expected for tests conducted on specimens with reduced grain boundary area, i.e., larger grain size. In support of this premise we have conducted tests on speci- mens having one to three grains per cross section for which a higher activation energy of 130,000 cal mole-1 was observed. Also, in agreement with results of Klopp et al., a faster creep rate resulted from the increased grain size and probable decreased dislocation density. Further argument against the cross slip mechanism is based on the constant activation energy we obsserved over the range of 5.0 to 10 kg mm-2,21 whereas the activation energy for cross slip displays a significant stress dependence.23 In addition to this, the powe on the stress term for the strain-rate dependence appears too high for cross slip. The values for tungsten fall in the range of 4.5 to 7 (Klopp et al. and Ref. 21) whereas values of approximately 2 are observed in creep by cross slip for hep metals.24 At temperatures from 3300° to 4000°F, Klopp et al. observed an activation energy of 141,000 ± 4000 cal mole-' which is less than that for self-diffusion, 153,000 cal mole-1, 25 and less than that reported for high-temperature creep of powder-metallurgy tungsten by Green:' 160,000 cal mole-1. Klopp et al. suggested that recovery of strain hardening by dislocation climb is the rate-controlling mechanism in this temperature region. Actually an activation energy larger than that for self-diffusion is predicted by this model if the temperature dependence of the elastic modulus27 is taken into consideration. Klopp et al. attributed this lack of correlation to the compositional differences between powder-metallurgy tungsten used by Green and their own arc- and EB-melted tungsten. It is our position that the value of 141,000 ± 4000 cal mole-' represents a transitional value between the higher and lower activation energies and does not represent a discrete mechanism of deformation. If the tests had been extended to higher temperatures the higher value of activation energy would have been observed as has been demonstrated by both our analy sis'' of isothermal test data by GE-NMPO28 and differential temperature tests28 on are-melted tungsten. The activation energies determined (170,000 and 160,000 cal mole-1) were greater than that for self-diffusion and are in better agreement with the value found by Green. The model of dislocation climb is associated with ; activation volume of 1 b3 according to Conrad.22 The activation volume calculated for the creep data of fou independent investigators in the temperature range where the activation energy for creep is near that for self-diffusion (Klopp et al. and Refs. 26, 28, and 30) is 110 to 2800 b3 and is in the range suggested for nonconservative motion of jogs. In the case of tungsten this mechanism may be preferred over that of dislocation climb. Sincere appreciation is expressed to Messrs. J. E. Flinn and F. L. Yaggee for the helpful discussions and suggestions in the preparation of this communication.

Jan 1, 1967

By Frank C. Aplleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO4•2H2O) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [Sulfur Combined Lime Trioxide Water (CaO) (SO,) (H2O) Gypsum 32.6% 46.5% 20.9% Anhydrite 41.2% 58.8% -] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product. End Uses The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris (the hemihydrate of calcium sulfate, CaSO4 ½ H2O) which when mixed with water will set or harden as the calcium sulfate returns to the dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uncalcined uses of gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in less developed countries where construction and other industrial uses may be quite limited, the use of uncalcined gypsum for portland cement retarder may well be the dominant-if not the only-market for the mineral. It has often been noted that calcium sulfate constitutes the world's largest reserve of sulfur, and minor use of both anhydrite and gypsum has been made to produce sulfuric acid or other sulfur compounds such as ammonium sulfate. However, because sulfur is readily available at lower cost from other sources, use of calcium sulfate has been limited to only a few locations where it could compete economically. No such use is reported in the United States at this time. Mineralogy Anhydrite, CaSO4 because of its geologically rapid conversion to gypsum, and relatively high solubility (about 0.2 g per 100 g H2O) is not often found outcropping in climates wet enough to support abundant vegetation except on steeply dipping slopes or other places where hydrated material is continuously removed. Anhydrite rock is most often light to bluish gray in color, and under the microscope, varies

Jan 1, 1983

By G. R. M. Del Giudice

A survey of the flotation literature of the past 10 years indicates an increasing use of the microscope as a tool for investigation. Thus, the metallurgical microscope has been used by Tucker and Head;' Taggart, Taylor and Ince;2 Ince,3 and del Giudice4 to examine mineral surfaces that had been subjected to the action of various flotation reagents and to the action of slime pulps. It has also been used by Gaudin, Groh and Henderson;5 Martin;6 Morrow and Griswold;7 and others to examine bakelite briquets of mill products. The microscope with transmitted light, both with bright-field and dark-field illuminations, has been used by Taggart, Taylor and Knoll8 and by Ince9 to observe Brownian motrement and flocculation in flotation pulps. The use of the microscope at low-power magnifications with incident illumination for the examination of mill products has been known for years.10 Finally, del Giudice11 has used a relatively new type of illumination, the Ultropak, for the examinntion of slime-coatings.

Jan 1, 1935

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By C. S. Samis, J. C. Mitchell

Sodion activity data have been obtained for the Na-A1 system for sodium concentrations in aluminum between NN, = 25 . 10-and 300 x 10'. This concentration intert-a2 encompasses those sodium concentrations nor1)zally encountered in aluminum reduction cell operation. The sodium activity data were measured by a two-phase equilibration of sodium between a lead and an aluminam rich phase. The Na-Pb system was emplojed as a reference for the determination of the actiz7itj 0.f sodium. The activity of sodiin in aluminuwz exhibits large positi2.e deviations frorn ideality and a strong dependence, on concentration below NN, = 100 x 1K6. The inteated data indicate that the activity of aluminium is equal to its mole fraction over the range of miscibility of the Na-A1 sgstem. The data on the Na-A1 binary have been combined with experimental data on the cryolite-A1 system at 1025°C to obtain the activities of Na F and AlF, in liquid cryolite oz2er the cornposition 1-ange encountered in aluminum cell operation. The results are in agreement with activities calculated from the NaF-AlF, phase diagram. ALUMINUM is produced commercially by the electrolytic reduction of aluminum oxide dissolved in molten cryolite. There is considerable controversy over the actual mechanism of the discharge processes, but sodium potentials in the systems appear to play an important role in the reduction mechanism. The metal-salt reaction involving NaF and aluminum to produce A1F3 and sodium is responsible for the presence of sodium in the aluminum metal phase. Additional sodium may be produced from the simultaneous deposition of sodium and aluminum at the cathode as a result of a cathodic overvoltage. runert' has suggested that sodium gas at atmospheric pressure would be the result of reaction between cryolite and aluminum at 1000°C. Subsequent investigations have shown that production of sodium at atmospheric pressure does not occur. These later investigations can be conveniently separated into two categories. The first involves sodium, aluminum, and cryolite, in which the sodium activity was measured. The second includes a lead phase for sodium activity measurement. Jander and errmann,' studied the reaction: at 1090°C in alumina crucibles under an atmosphere of dry, oxygen-free nitrogen. The equilibrium constant for the reaction was expressed in terms of concentration. Their results in Fig. 1 show an increase in sodium content of the aluminum with increasing NaF/A1F3 weight ratio. Pearson and waddington3 performed similar experiments at 1000°C. Their results are included in Fig. 1. Dewing and ollinshead have measured the sodium content of aluminum as a function of the NF/AF, ratio at 1025"C, Fig. 1, and ewin' measured the sodium content of the aluminum in a system involving the solid reactants NaF, cryolite, and liquid aluminum. This reaction is different from those discussed above. Two solid phases, NaF and Na3A1F6, and a liquid aluminum phase were present. The sodium concentration in the aluminum was determined by the temperature. Dewing's measurements covered the temperature range 679" to 896°C. Omo, Matsushima, and 1t02" investigated the equilibrium 6NaF ential thermal analysis. Stokes and Frank6 determined sodium activities by

Jan 1, 1970

By Ian Wark

IN the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practiced at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts off many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies-the Broken Hill South, the North Broken Hill, and the Zinc Corporation-together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism.

Jan 1, 1932