Search Documents

By C. E. Shoenfelt

Jan 1, 1942

By J. E. Strassner

Oilfield emulsions are stabilized primarily by film-forming asphaltenes and resins containing organic acids and bases. Adding inorganic acids and bases radically changes the physical properties of these films and their emulsion-stabilizing properties. Interfacial films show one of three different physical characteristics when retracted in pendent drop tests. These compressed films have rigid, soap-type or minimum film properties depending on the quantity of asphaltenes and resins in the crude oil and on the pH and composition of the brine. There exists for each crude oil-brine system an optimum pH range over which the adsorbed film exhibits minimum contracted filtn properties. In this range, intmfacial tension is high — frequently near its maximum value — indicating the absence of highly surface-active specier; crude oil-brine emulsions generally show minimum stability; and surfactant requirements for breaking these emulsions are significantly reduced — sometimes no surfactant is needed. About two-thirds of the world's crude oil is produced as emulsions that must be treated (demulsified) to be marketed.' Approximately three-fourths of all domestic crude oil produced must be treated. The percentage of crude requiring treatment increases as fields become older and more water is produced. Demulsification most frequently is attained through use of surfactants, heat and electric treaters. It is estimated that over 75 percent of all oilfield emulsions are broken by chemicals generally containing alkylene oxide condensates. Although acids and bases are known to affect emulsion stability:-' they rarely are used in the oil field except in batch treatment of the most severe emulsions. Nevertheless, pH adjustment by using acids or bases in demulsification has some advantages over other methods. Mainly, it is cheaper. Acids and bases frequently are cheaper to use than surfactants, or can appreciably reduce the amount of surfactant required for demulsification. Secondary advantages are that less oil is lost by emulsi-fication into the aqueous phase, and that less corrosion is encountered when the optimum pH is basic. Limitations to the use of pH include (1) use in brines containing high concentrations of reactive ions, (2) closer supervision for pH control than is required for surfactants and (3) need for corrosion protection when the optimum pH is sufficiently acidic. These factors indicate that the economics of pH con trol in demulsification will be maximized when relatively large treating facilities are needed, when relatively large surfactant concentrations are required to break an emulsion, when a relatively low concentration of the aqueous phase is emulsified in the oil and when the emulsified aqueous phase contains relatively low concentrations of reactive ions. Because there are no broad guide lines for using pH control in breaking oillield emulsions (and because the limited guides available are highly specific and frequently contradictory), this paper will attempt to clarify the principles involved in using acids and bases to break emulsions. These principles also should be useful in refinery separations and in other oilfield applications where stable or unstable petroleum emulsions are involved. Principles of Emulsion Stability Oilfield emulsions generally occur as water droplets dispersed in oil (w/o) and occasionally as oil droplets in water (o/w). These emulsion droplets are usually in the 0.1- to 10-micron range. However, more coarsely dispersed water droplets frequently are present in the emulsion. Pure hydrocarbons and water will not form stable emulsii except in extreme dilutions where the large distance brtween droplets inhibits coalescence. An emulsion breaks because interfacial tension acts to minimize the surface area of the dispersed drops by coalescence. However, emulsions can be stablized for long periods of time by the presence of a third phase that adsorbs at the oil-water interface and inhibits coalescence of the dispersed phase."' Emulsions generally are stabilized by (1) repulsive charges on the surfaces of the dispersed phase and (2) adsorbed films that, being preferentially wetted by the continuous phase, act as a physical barrier to inhibit contact between the dispersed droplets. Both these factors generally are important in stabilizing and in breaking o/w emulsions. However, repulsive charges are less effective in stabilizing w/o emulsions which generally are stabilized by adsorbed films.V or this reason the nature and importance of these films at oil-water interfaces were examined closely; as will be shown, pH changes were found to affect the films significantly, and this work led to laboratory tests of pH- adjustment in emulsion breaking. This paper will present evidence to show that emulsions are stabilized primarily by films that form around droplets

Jan 1, 1969

By Lee Morris, Charles E. Lawall

This paper represents the results of a study to determine the source, mode of occurrence and conditions influencing the flow and liberation of large volumes of inflammable gas in the Pocahontas No. 4 coal bed in southern West Virginia. A study of this kind is of interest in connection with mine ventilation, because in the removal of gases from coal mines it is very important to know the origin, the occurrence and laws of gas flow. The study was started in April, 1931, and the data and observations were obtained throughout a period of 15 months of field work. Geology The country where this study was made is mountainous and rugged; great cliffs, precipitous slopes and deep narrow gorges are found throughout the area. The outcropping rocks consist of stratified layers of sandstone, shale, limestone and deposits of coal of Carboniferous age. The Pottsville series of the Pennsylvanian, lying at the base of this period, cover the greater portion of the area. A stratigraphic section of the Pocahontas group of the Pottsville series is shown in Fig. 3. The older rocks outcrop in the extreme southeastern part of the area, but are under drainage in the central and northern parts due to the gradual northwest dip of the strata. The structure has a general northeast-southwest trend (Fig. 1). North of Dry Fork anticline the strata have been only slightly disturbed by movements of the earth's crust; it is now a long monocline. Southeast1 of Dry Fork anticline the strata are warped into great arches and deep troughs and are broken by overthrust faults. All of this folding is probably the result of the intense folding associated with the formation of the Appalachian Mountains. Pocahontas No. 4 Coal Bed The Pocahontas No. 4 bed, lying approximately 550 ft. above the base of the Pottsville series, is one of the thickest and most gassy coal beds in

Jan 1, 1934

By G. H. Clevenger

Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914. See Trans., xlviii, 3 to 32 (1914). This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developzn~ents which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be: First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all limes a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the bulk of my discussion will be confined to the presentation Of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation by others of data of practice in other districts which will assist in reconciling this divergence of opinion.

Jan 1, 1915

By W. S. Owen, T. Bell

The variation ox the M, temperature with nitrogen concentration has been determined experinzentally. The free-energy difference between martensite and the parent y Phase at the M, temperature,is computed for Fe-C and Fe-N alloys using recent solubility data fm the Fe-N system and new data for the variatim of the activity of the interstitial solute in the y phase with concentration. The "geometric model" is considered also, and the importance of Zener ordering is noted. It is shown that, although at any chosen concentration the M, temperature and the activity are significantly different in the two alloy systems, the free-energy duference is the same within the limits of experimental error, thus Providing further evidence of the very close similarity between the martensite transformations in Fe-C and Fe-N alloys. TO estimate the free-energy change accompanying the martensite transformation in binary interstitial alloys it is necessary to know the variation of the Ms temperature with interstitial solute concentration and some thermodynamic data. To date, only the Fe-C system has been discussed because this was the only system for which relevant experimental measurements had been made, but even in this case the data available are insufficient to permit the free-energy change to be calculated without the assumption of a thermodynamic model for the y and a solid solutions. The last comprehensive discussion of the topic was by Kaufman, Radcliffe, and Cohen in 1.960.' Since that time Ellis, Davidson, and Bodsworth2 have redeter mined the activity of carbon in y iron as a function of carbon content and Atkinson3 has measured the activity of nitrogen in Fe-N austenite. The M, temperature of Fe-N is reported in the present paper. Thus, it is now possible to assess the free-energy change accompanying the martensite transformation in Fe-N alloys on the same basis as that used to assess the change in Fe-C alloys. This comparison is of interest because it has been shown recently4 that the structure of the martensite formed in Fe-N alloys changes with nitrogen content in a manner exactly parallel to the changes in structure in the Fe-C series and that the strain associated with the distortion of the iron lattice in either the y or the a phase by a nitrogen atom is the same as that produced by a carbon atom. The work to be described tests whether or not this close similarity between the two systems extends to the thermodynamics of the martensitic transformations. THE Ms TEMPERATURES FOR Fe-N MARTENSITE Bose and Hawkes5 found the M, temperature of a eutectoid Fe-N alloy (2.35 wt pct N) to be 35°C. This single determination appears to be the only reported measurement of the M, temperature of an Fe-N alloy. In the present work a series of more than fifteen different specimens containing between 0 and 2.7 wt pct N were prepared by controlled nitriding of pure iron wire 0.010 in. diam. The iron was supplied by B.I.S.R.A. and was designated ACN2. The nitriding procedure, all aspects of which are critical, has been described in detail elsewhere.' Each specimen was quenched from the austenitizing temperature into brine at 20°C without removing the specimen from the ammonia-hydrogen atmosphere in which it was ni-trided. Alloys containing up to 0.7 wt pct N were fully martensitic. More concentrated alloys contained progressively more retained austenite. At 2.34 wt pct N the specimen was completely austenitic after quenching to 20°C. The M, temperature of specimens with M, temperature above 20°C (those containing less than 2.35 wt pct N) was determined by a thermal arrest technique. For the more concentrated alloys (2.35 to 2.70 wt pct N) the variation of electrical resistance with temperature down to -196°C was used. Unlike Fe-C alloys, Fe-N alloys cannot be reaus-tenitized in vacuum or in an inert atmosphere because excessive loss of nitrogen occurs, even in short times, at high temperatures. Consequently, the alloys were reaustenitized in the ammonia-hydrogen mixture corresponding to nitrogen equilibrium at the temperatures used. The specimens were quenched in a blast of cold hydrogen gas and the temperature, measured by a thermocouple welded to the 2.5-in.-long specimen, was recorded on a high-speed recorder. In the first experiments 0.002-in.-diam chromel-alumel wire thermocouples were used but it was found that these gave erroneous readings due to contamination by nitrogen pickup. Pt-Pt 13 pct Rh wires of 0.002 in. diam were found to be satisfactory. Further details of the experiments are available in the original thesis.7 The cooling rate was controlled between 400° and 4000°C per sec by adjusting the hydrogen pressure. At least three cooling curves were obtained for each composition. Each specimen was analyzed for nitrogen after quenching. To aid in the accurate location of the martensite arrest points a series of cooling curves of 0.010-in.-diam platinum wire were recorded and these, which did not contain an arrest, were used as comparison standards. Four specimens, each in the form of a 3-in. loop, were prepared from each of the four alloys containing more than 2.35 wt pct N. One specimen was used for nitrogen analysis, one for X-ray diffraction, and two for resistance measurements below 20°C. The latter specimens were quenched from 20°C into constant-temperature baths at selected lower temperatures.

Jan 1, 1968

By E. Orowan

LONG before the role of dislocations in the plastic deformation of crystals was recognized, the stress-strain field around dislocations received considerable attention in the theory of elasticity. It seems that Weingarten1 was the first to consider dislocations as simple and typical sources of internal stress in elastic solids, and Volterra2 and Timpe3 investigated their elastic field. Fig 3-1 shows the two basic types of dislocations considered by Volterra. The first arises by making a straight-edged .plane cut in a solid, displacing the two surfaces of the cut in their own plane relatively to one another by a constant amount in a direction perpendicular to the edge, and welding them together; this is shown in Fig 3-la, where the outer cylindrical surface represents the boundary of the solid, and the thin spiral cylinder around the edge of the cut has been removed in order to avoid infinities of stress and strain. The second type of dislocation is shown in Fig 3-lb; here the surfaces of the cut have been displaced relatively to one another by a constant amount parallel to the edge, and then welded together. After J. M. Burgers,4 these two types are called edge and screw dislocations, respectively. They represent simple limiting cases; in the general case, the surfaces of the cut are displaced by a constant vector that lies in the plane of the surface but has components both parallel and perpendicular to the edge of the cut. This vector is the Burgers or slip vector. The name “dislocation” was given by A. E. H. Love;5 it was bor-

Jan 1, 1954

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

CONTENTS PAGE BARTON, D. C.-The Eötvös Torsion Balance Method of mapping Geologic Structure (T. P. No. 50) 1 GEORGE, P. W.-Experiments with Eötvös Torsion Balance in the Tri-State Zinc and Lead District (T. P. No. 65). 15 LANCASTER-JONES, E.-The Computation of Eötvös Gravity Effects (T. P. No.75) HEILAND, C. A.-A Cartographic Correction for the Eötvös Torsion Balance-(T. P. No. 52) 17 SLICHTER; L. B.-Certain Aspects of Magnetic Surveying (T. P. No. 120). . . . 18 WEAVER, W.-Certain Applications of the Surface Potential Method (T. P. No.121) LUNDBERG, H.-Recent Results in Electrical Prospecting for Ore (T. P. No. 98). . 20 HOTCHKISS, W. 0., ROONEY, W. J. and FISHER, J.-Earth-resistivity Measure-ments in the Lake Superior Copper Country (T. P. No. 82) 21 LEONARDON, E. G. and KELLY, S. F.-Some Applications of Potential Methods to Structural Studies (T. P. No. 115) 23 MASON, M.-Geophysical Exploration for Ores (T. P. No. 45) 25 The Eötvös. Torsion Balance Method of Mapping Geologic Structure Discussion of the paper of D. C.. Barton, issued as Technical Publication No. 50 with Mining and, Metallurgy, February, 1928. D. C. BARTON.-The field surveys which I have been privileged to use as illustrations for this paper were done for Mr. DeGolyer's companies and were released through his favor. W. J. MILLARD, Tulsa, Okla.-Has any oil been found by the torsion balance in West Texas? D. C. BARTON.-NO new oilfield has been discovered on the basis of torsion balance work. It has had some part in controlling the policy of certain companies in playing the extension of known oil fields. A number of "T. B." structures have been drilled and dry holes obtained. Of those known to the writer, one apparently was a structural high, one is a broad general high but locally low and probably is a deep-seated structural high, one seems normal although the control is poor, and one was considered structurally low but is now suspected by some geologists of being structurally high. E. L. DEGOLYER, New York, N. Y.-A large gravity structure, generally referred to, I believe, as the Crosby County Structure, has been found in West Texas. This structure is perfectly symmetrical with the arrows all pointing toward a common center, very much like the Nash salt-dome pattern in Dr. Barton's paper (Fig. 9). One of the peculiar things about it, from the standpoint of the gravity high, is that it is so

Jan 1, 1928

By John Gann

THE following investigation constitutes a brief resume of the more important binary magnesium alloys from the standpoint of metallographic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn.

Jan 1, 1928

By R. W. Raymond

The absence of a convenient glossary- of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copy, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By David P. Hale

THE Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,1but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1938

By William Colby

INCREASING governmental control of human activities seems inevitable. Within the present generation railroad rates and the public sale of water, gas and electricity have been subjected to rigid regulation. The field of control is slowly but surely being enlarged, and it is the object of this paper to outline in brief space this tendency toward increased governmental regulation, as far as mineral resources are concerned. Our, dual form of government complicates the problem. We must deal not only with the powers of the Federal Government, but also with those of the individual States. In order to approach this question intelligently we must have some conception of the powers and jurisdiction of the States and the United States, respectively, over mineral lands and mineral production. Starting with the Federal Government we find it never owned any public domain within the States that formed a part of the thirteen original colonies and, for historical reasons, the same is true of Tennessee and Texas. The Mid-Western States were erected out of the public domain which was acquired by the United States through cession from the original States or by purchase from foreign nations. Congress early in the last century adopted a policy of leasing public lands containing lead deposits in a portion of this Mid-Western territory, but later abandoned that policy and disposed of such public, lands, mineral and non-mineral, outright so that they long since have practically all passed into private ownership and become subject to the general jurisdiction of the respective State governments. In the great public domain lying west of the Mississippi River, and in portions of some of the Southern States, the Federal Government adopted a new mineral land policy following the discovery of gold in California. (Acts of Congress of 1866, 1870, and 1872.) The mineral lands within these States, instead of being disposed of on the game basis as agricultural lands, as occurred in the Mid-Western States, were segregated from agricultural lands and sold under special laws intended to encourage mining, giving the miner the free right to locate and work these mineral lands without paying any royalty to the Federal Government. A miner could also obtain at slight expense a complete

Jan 1, 1930

By William P. Blake

The Rainbow Lode is situated at Walkerville, in the Summit Valley mining district, Silver Bow County, Montana Territory, about one mile from Butte City. It was so named ill 1876 by Mr. J. E. Clayton, in recognition of the broadly-sweeping curve of the outcrop across the rounded surface of the eastern slope of a granitic mountain, at an elevation of about 6000 feet above the sea-level. It is on the western side of the range which divides the waters of the Missouri from those of the Columbia. History.—The history of the district is an instructive one. The water-courses and flanks of the hills were worked for years for placer gold. Millions of dollars' worth of low-grade gold have been washed out of the surface gravels below the veins of the district. Missoula Gulch and Silver Bow creek, just below Butte, are noted for their rich placers, and they continue to yield largely, producing within narrow limits from $50,000 to $100,000 dollars' worth of golddust yearly. It is ragged vein-gold, and evidently is near its parent source. It is no doubt derived from the disintegration of the veins of the district, and this conclusion was soon forced upon the miners. The veins which were seen outcropping boldly upon the slopes above them were located, and prospecting commenced. These outcrops were found heavily stained and blackened with oxide of manganese, and were porous and honey-combed in places, showing that the quartz was formerly filled with pyritous ores, and that these ores had decomposed and dissolved away, leaving, however, portions of the precious metal behind, especially at and near the surface of the ground. Assays of the croppings gave variable and often contradictory results; but the fact. that these were the outcrops of lodes bearing gold and silver in depth was patent to any experienced observer of mineral veins. The lodes of the district were first brought prominently to notice by Mr. Clayton in 1876, and in October of that year the Alice mine, upon the central portion of the lode, was opened by Mr. Marcus Daly, now so well known as the superintendent of the Anaconda Copper mine, upon another extremely interesting lode, in the same region.

Jan 1, 1888

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others developed on land by means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.' Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions, have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with the large features, and only by utilizing all the related sciences shall we

Jan 1, 1927

By R. D. Pehlke, J. V. Gluck

A study was made of the effect of small additions of metallic solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450o to 650°C. The experimental measurements were made in a multielectrode galvanic cell using. a fused LiCl-KCl electrolyte. The activity of zinc in binary solution exhibited a strong positive deviation from Raoult's law and obeyed Henry 's law to at least 0.050 mole fraction. The ternary addition of lead, gallium, or indium increased the activity of zinc. Cadmium or tin additions slightly decreased the zinc activity. Copper, mercury, silver, or antimony caused moderate decreases, while gold strongly decreased the zinc activity. The results are expressed in terms of Wagner's interaction parameter ejZn and a second-order cross-interaction parameter. The interactions for copper, gold, silver, and antimony showed a linear dependence with reciprocal absolute temperature, while the other interactions were essentially independent of temperature over the experimental range. Since tin and antimony decreased the zinc activity, the hypothesis of a purely periodic variation with atomic number was rejected. A semiquantitative explanation was possible with a free-electron model when relative electronegativities were used to express changes in the electron/atom ratio caused by the solute addition. Random solution and quasi-chemical models correctly predicted the majority of the interactions for which binary data were available to apply them. A knowledge of the thermodynamic interactions in liquid (and solid) metallic solutions is of considerable theoretical and experimental interest in the formulation of quantitative thermodynamic relations for metallurgical processes. The approaches to defining the interactions may be either phenomenological (i.e., "What mathematical function adequately describes observed behavior and permits extrapolation to new situations?") or theoretical, such as a specific model

Jan 1, 1968

By S. R. Titley

The recent emphasis placed upon the use of molybdenum as a geochemical indicator has stimulated considerable inquiry into the behavior of molybdenum in the zone of oxidation. This paper represents a summary of recent and continuing experimental work and calculations in an investigation of a portion of the system Mo-Fe-S-H20 and treats the stability of various iron and molybdenum compounds with respect to oxidation potential and pH. Using experimentally determined free energy values for ferrimolybdite, diagrams of the stability fields of this mineral have been calculated with respect to ilsemannite (?), molybdenite, pyrite and limonite. This theoretical approach is the one utilized by Garrels3'4 in studies of the relationships of various minerals in the zone of oxidation. Use of this approach is particularly suited to the study of geochemistry in the zone of supergene processes because of the low temperatures, low pressures and other relatively easily determined and duplicated factors that exist in the near surface environment. Such a study of molybdenum, however, is complicated by several factors. One of these is the fact that the strong amphoteric behavior of molybdenum makes possible a wide variety of substances and complexes whose exact chemical natures are unknown. The second factor is the dearth of thermodynamic data for many of the simplest of the possible compounds and ions important to the study. For the purpose of this study, the problem of complexes has been approached through considering only the simpler possibilities realizing that the complexes and systems so treated may be gross oversimplifications. All the complexes considered, however, have been suggested in the chemical 2,7,9,12 or geologi-cal literature. EXPERIMENTAL WORK Studies of the behavior of molybdenum ions and ferrimolybdite have been carried out in aqueous sys- tems, and reactions have been followed by simultaneous measurement and recording of pH and oxidation potential. A major problem involved in this study was the long periods of time necessary for equilibrium to be established in some of the systems considered; in a few instances, these periods exceeded four weeks, that is, four weeks during which measured conditions changed continuously. Another problem, in some instances, was the indeterminate nature of the reactions that have taken place. Because of the tendency of molybdenum to complex, reactions which take place under some of the more extreme imposed conditions of oxidation and acidity or alkalinity are unknown. However, useful data for the present work were obtained from studies of the molybdate ion and ferrimolybdite between pH 2 and 8 and under only moderately oxidizing to nonoxidizing conditions. Instruments used in the experiments were a Hewlitt-Packard Model 412A VTVM, a modified Beckman Zeromatic pH Meter and two Varian model 11 recorders. pH was measured between glass and calomel electrodes and Eh was measured between calomel and platinum electrodes. Conditions of pH were varied with 1N H2SO4 and 1N NH4OH and 1N NaOH. Eh was varied with gaseous nitrogen, oxygen or aqueous H202. Ambient temperature was essentially uniform at 24ºC and was increased in the reaction vessel by the positioning of a magnetic stirrer whose temperature was sufficient to bring the temperature to 2S°C in the reaction. The temperatures of reaction did not vary more than 1/2ºfrom 25°C. Two reactions were investigated, the ferrimolybdite-limonite-water reaction and the reduction of molybdate ion. Studies of both reactions yielded useful data that were used in preparation of the Eh-pH diagrams. The traces of the reactions are shown on Fig. 1. Ferrimolybdite-Limonite- Water: Studies of this reaction involved analysis of the solution of ferrimolybdite and simultaneous formation of ferric hydroxide. The data are summarized on Fig. 1. In this reaction, equilibrium was attained at various pH's when coexistence of the two solid phases (ferrimolybdite and ferric hydroxide) was attained. At the proper pH, controlled by the amount of ferrimolybdite and thus the dissolved content of molybdate species, both phases were observed and reaction times to complete the transition were on the order of weeks. The reac-

Jan 1, 1963

By M. J. Blackburn

The phasal equilibria in TI':Al alloys has been studied Ry transmission electron microscopy, electron diffraction, and X-ray diffraction. It is shown that three-phase fields exist below the transformation, viz.: a disordered hexagonal solid solution a; an ordered hexagonal phase based on Ti3Al, aa; and a two-phase region. (a + (YZ) , occurring between the single-plzuse fields. The size. disiribution, and morphology of- the a, phase in the two-phase region is shown to be dependent upon the alloy composition and heat treatement. The ordering process in the a, phase leads to the formation of anliphase domain boundary networks; the contrast and stability of these networks is shown to be dependent on alloy composition. A new and relatively simple phase diagralil for the systemm is constructed. The phasal equilibrium at the titanium-rich end of the Ti:Al system has long been the subject of considerable controversy. crossleyl has recently reviewed the phase diagrams that have been advanced for the system and in his turn proposed yet another one. There would seem to be general agreement that a phase exists at a composition at or near Ti& with an ordered hexagonal DO,,-type structure. However, several other phases have been proposed; for instance, Ence and ~ar~olin's' diagram includes two phases, Ti2A1 and Ti3A1, in the region up to 25 at. pct Al. The position of the proposed phase boundaries varies over a considerable compositional and temperature range, a point graphically illustrated in Fig. 1 of Crossley's paper.' It is perhaps germane to briefly examine the techniques used by other workers in the establishment of the phase structure. These fall into three categories: 1) X-ray diffraction, the only limitation of which is the rather low intensity of superlattice reflections in this system.3 Thus, superlattice reflections become increasingly difficult to detect in the more dilute aluminum alloys. 2) A considerable amount of optical microscopy has been performed"2'4 and it will be shown in a later section that many of the obscure mi-crostructures that have been observed can be attributed to hydrogen contamination. It is concluded, therefore, that such observations should be interpreted with considerable care. 3) The variation of some physical property with aluminum content has been measured.5"7 These methods are a useful indication of the existence of a transformation, but are usually insufficient in themselves to identify the transformation. The results using these techniques will be considered in more detail in the discussion. In this paper, the phase structure of alloys containing up to 25 at. pct A1 has been studied by transmission electron microscopy and X-ray techniques, and the results are used to generate a new and relatively simple diagram for the titanium-rich end of the Ti:Al system. EXPERIMENTAL A series of alloys containing 5.05, 10.16, 13.39, 13.99, 14.40, 20.83, and 25.05 at. pct A1 were obtained in the form of hot-rolled sheet 0.02 in. thick. These alloys contained 0.10 to 0.15 pct 0. Thirty-gram arc-melted buttons were prepared from iodide titanium and 99.99 A1 which contained 16.1, 16.9, 18.2, 19.0, 21.6, 22.2, 23.0, and 23.9 at. pct A1 and had an average oxygen content of 0.03 pct 0. The differences in oxygen content did not appear to influence the nature of the phase transformations which were found. Oxygen content may affect the temperature of these transformations, but insufficient samples of the high-purity alloys were examined to answer this question. The heat treatment of alloys was performed in dynamic atmosphere and vacuum furnaces or in helium -filled silica capsules. A special vacuum furnace was constructed to provide a high quenching rate in which rates of 4000°C per sec were obtained using water as the quenching medium. As pointed out by Crossley,' it is important to avoid heat treatment in the a - [} phase field as the resultant segregation of the alloy into the two phases containing different amounts of aluminum can persist through subsequent treatments leading to ambiguous results. It will be demonstrated later that step cooling of specimens from the a phase region can also lead to anomalous effects. Thus, all solution treatments were carried out in either the a or 3 phase fields followed by water quenching and subsequent isothermal annealing at various temperatures. X-ray analyses were performed on a diffractometer on fine-grained bulk specimens. The value of long-range order parameter, S, wa_s calculated from the integrated intensity of the (1211) reflection. In general, the intensity of the (1011) superlattice reflection was compared with that of the (2021) fundamental reflection to correct for experimental differences between measurements. Thin foils for electron microscopical examination were produced by electropolishing using the technique described in an earlier paper.8 Dark-field techniques were employed to a large degree in this investigation using the gun-tilt method. Finally it should be noted that the lattice parameters of the D01,-type superlattice are approximately related to the disordered hexagonal phase parameters by Crf - c, and 2ad - a, where the subscripts s and d refer to the ordered and disordered unit cells, respectively.

Jan 1, 1968

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968