Search Documents

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Christopher G. Atwater

The object of this paper is to describe and discuss the progress that has been made, up to the present date, in the development of the modern by-product coke-oven. There are few members of the Institute who have not heard more or less of the by-product oven-installation, and there are many whose acquaintance with it is intimate and practical. Since the general opinion on the subject has hardly become crystallized as yet, it is hoped that this paper will at least furnish matter for discussion. In order to obtain an idea of the present status of the industry in the principal iron-producing countries, the following table has been prepared : Table Showing Proportion of Coke Made in By-Product Ovens in Various Countries. United Kingdom (1898, Mr. George Beilby). Short Tons. Per Cent. Coal coked in by-product ovens,. .. 1,400,000 7.9 Coal coked in blast-furnaces with by-product recovery,.......2,240,000 12.7 Coal coked in non-by-product ovens,. . 14,000,000 79.4

Jan 1, 1903

By C. R. Swarts

The use of compressed air or gas in oil wells for raising crude oil to the surface has, within the last year, become a dominant factor In production engineering. Previous application of this principle was largely confined to oil wells that had been pumping for a considerable length of time. In the Seminole area, the gas-air lift has been applied to wells imniediately after natural flow has ceased and in some cases while the wells were still flowing. This early application of the gas-air lift has been watchcd with intense interest by the petroleum industry, both with respect to methods of application and mechanical installations and to the effects on immediate and ultimate production. Methods of Application The Seminole pool at its inception contained sufficient gas associated with the oil to cause natural flow. As no frce gas was found in the main productive horizon, the Wilcox sand, all the gas present was dissolved in the oil, hence the natural flowing life was short, rarely lasting over 45 days. When natural flow ceased, high fluid levels were common, and as depth and crookedness of holes were obstacles to efficient pumping, the gas-air lift was used almost exclusively in raising the oil to the surface. Because of the high gravity of the oil, 41" A. P. I., and its high gasoline content, and also because of the desire to obtain production before offset wells became productive, quantity of production was the aim of the operators and a method of flow was used whereby this aim could be fulfilled. One of the outstanding features of this method consisted in flowing the wells through the annular space between the tubing and rasing. By this means a greater quantity of fluid could be handled than by flowing through the tubing of the size in ordinary use. Wells that would produce only a few hundred barrels on the pump were by this rnethod made to produce as high as 7000 bbl. on the lift. A few days or wreks of production at that rate meant a large recovery of oil. Casing of 636 in. diameter was commonly used as a production string with a 5 3/16-in. liner set on top of the oil sand. Upset tubing for irtro-

Jan 1, 1928

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

THE International First-Aid and Mine-Rescue con-test, under the auspices of the U. S. Bureau of Mines, was held at Butte, Mont., on Aug. 20, 21 and 22. As usual, the first-aid elimination contests were held the first day, the finals the second, and the mine-rescue contest the third. While the number of teams entered was not as great as at some previous contests held nearer the coal-mining districts of the East, the atten-dance was much larger than usual, due to the great interest in first aid, rescue work, and accident preven-tion that has been created by the effective support and constructive policy of the Anaconda Copper Mining Co. toward them. The winner of the first-aid contest was the Great Falls Zinc Mill team of the Anaconda company, of which Fred Erickson is captain. Second place went to the Baton Rouge team of the Standard Oil Co. of Louisi-ana, and third to the Great Falls Furnace Refinery team of the Anaconda company.

Jan 9, 1928

By J. C. Irvine

Meramec Mining Co., a joint venture of Bethlehem Steel Corp. and St. Joe Minerals Corp., mines and pelletizes iron ore at the Pea Ridge mine. The Pea Ridge property is located near Sullivan, Miss., about 113 km (70 miles) southwest of St. Louis. The ore body was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the ore body was mineable. Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production began in April 1964. The ore body is overlain by about 400 m (1300 ft) of flat-bedded sediments. It is tabular, about 800 m (2600 ft) long and up to 180 m (1600 ft) thick. It dips about 80° and is of unknown depth. The ore is mainly high-grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry.

Jan 9, 1976

By Jack A. Simon, M. E. Hopkins

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By W. Kennedy

THROUGHOUT northeastern Texas we have an extensive series of iron-ore deposits, occupying portions of nineteen counties and having approximately an actual ore-covered area of 1000 square miles. The existence of these ores has long been known. Kennedy* says: "Iron-ore is distributed in profusion throughout Texas, being found almost everywhere except in the level region of the coast." Before this, C. Newell† had mentioned the existence of these ores thus: " Iron is found in abundance in the eastern, northern and middle portions of Texas;" and in 1849 Edward Smith‡ said: " We met with immense hills of iron which were said to be, and appeared to be, of excellent quality, in Cass and Titus counties.. . .. It is well known that Texas abounds with iron of first-rate quality." In 1859, Dr. Shumard? reports that detailed surveys had been made in several counties, and says: " Our labors have demonstrated the important fact that we have a vast iron-region in the eastern part of the state, embracing considerable areas in Cass, Harrison, Rusk, Panola, Smith, San Augustine and Shelby counties. The ore-deposits belong to the Tertiary era and consist chiefly of hematites and limonites, of which there are several varieties. We have also found in this district extensive beds of carbonate of iron." Dr. Shumard gives no very exaggerated description of Cass county§ as it then existed when he says : " Cass county alone is capable of supplying a number of furnaces with an abundance of excellent iron-ore for many years." Of Rusk county he says: "Our de-

Jan 1, 1895

APPROXIMATELY 90 per cent of the steel that is melted and refined in the United States and poured into ingots is made in basic open-hearth furnaces, as shown in Table 1-1. The annual ingot capacity of the steel industry reported January 1, 1950, by the American Iron and Steel Institute3* was 99,040,160 tons, of which the basic open-hearth process accounted for 85,896,580 tons, 86.7 per cent of the .total. The capacity of the individual furnaces varies over a wide range, a large majority falling within limits of 50 to 200 tons (Fig 1-1). Most of the units constructed [ ] since 1942 are in the larger size groups, between 175 and 225 tons capacity.

Jan 1, 1964

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By Henry Lloyd Smyth, J. Ralph Finlay

The most important area of the so-called Keewatin rocks of northern Minnesota is that which runs westerly from Lake Saganaga, near the national boundary, and finally disappears beneath the drift (or has not been farther traced), in the neighborhood of Vermilion Lake. With this belt we have a general acquaintance, extending back some four years. During the past year we have had the opportunity of studying in considerable detail a small part of it, embracing an area of about 12 square miles on the south and east shores of Vermilion Lake. In this paper we desire to record our observations and conclusions, which seem to us important. II.—Literature. Outside the Minnesota Geological Survey, the list of the investigators who have studied the geology of the Vermilion Lake area is not long. Whittlesey, in 1876,* mentioned the occurrence, in the area about Vermilion Lake, of rocks resembling the Canadian Laurentian. Chester,? in 1884, described the iron-ore at Vermilion Lake as occurring in connection with jasper and quartzite, intimately bedded with the country-rock, chiefly sericite schist, and standing in a nearly vertical attitude. The Vermilion iron-bearing rocks, and those of the Mesabi range, he says, are of the same age.

Jan 1, 1896

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem'ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam'ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

By B. F. Fackenthall

The Durham Iron Works of Messrs. Cooper & Hewitt, near Riegelsville, Pa., occupy a site which has been almost continuously the scene of iron-manufacturing industry since 1727. Doubtless if Anthony Morris and his thirteen associates, who in that year erected a blast-furnace on the Durham Creek, a short distance above where the Durham Iron Works now stands, could have had a vision of the improved and enlarged apparatus of their successors, they would have been not less astonished by the huge stack, the hot-blast ovens, and the blowing-engines of the modern blast-furnace, than by the railroad which now follows the bank of the river on which their clumsy " Durham boats " once floated pig-iron to Philadelphia. In one particular, posterity must confess their snperiority. We are told that in November, 1728, they shipped three tons of Durham iron to England. The proprietors of the Durham Iron Works are not now shipping iron to England. The present Durham furnace was built (in place of two smaller ones) in 1874 and 1875, and made its first blast in 1876. A description of it, with other works of the same proprietors, at Trenton, N. J., by A. L. Holley and Lenox Smith, was published in London Engineering for January 31st, and February 21st, 1879. Since that time, a number of improvements, dictated by experience, have been made in the details of the furnace and fittings; and the recent roilclusion of a long and successful blast presents a convenient opportunity for a description of the works and a statement of the results of practice. The accompanying drawings will show the general arrangement of the works. The furnace, Plate I., Figs. 1 and 2, is 75 feet high by 19 feet bosh. The hearth is 11 feet 4 inches in diameter, with seven tuyeres 5 feet 6 inches above hearth-line. The tuyeres project 9 inches into the furnace, making the interior tuyere-circle 9 feet 10 inches in diameter. The front is a modification of Luermaun's

Jan 1, 1886

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By J. W. Freeman, J. P. Rowe, R. F. Decker

HEAT-to-heat variations in properties of an alloy of constant nominal chemical composition have been a perplexing problem to the metallurgist. These heat-to-heat differences have been especially baffling in high-temperature metallurgy. In order to establish fundamental reasons for these heat-to-heat variations, the National Advisory Committee for Aeronautics has sponsored and financially assisted an extended research program on heat-resistant alloys at the University of Michigan. As part of the program to find the contribution of processing variables, Frey, Freeman, and white' studied effects of heat treating on nickel-base alloys and Ewing and reeman' investigated effects of hot-working practice on N155 alloy. To extend the program to the study of effects of melting practice on high-temperature properties, a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 pct A1 composition was selected for experimentation. The objective of this program was to establish the melting-practice variables which influenced the hot-working characteristics and creep-rupture properties and, at the same time, establish the metallurgical mechanisms for the effects. During the course of the investigation of practices using vacuum melting, it became increasingly evident through chemical analyses supplied by industrial concerns that a major variable was melt reaction with the crucible. This paper is devoted to the results of this phase of the melting-practice study. EXPERIMENTAL PROCEDURES Experimental 10-lb heats were induction melted in the University of Michigan vacuum-melting unit with the melting practices outlined in Table I. Aim analysis for the basic alloy, in wt pct, for all heats was as follows: Cr Co Mo Ti Al 20.0 15.0 4.0 3.1 3.1 Mn Si C Ni 0.12 0.12 0.08-0.15 Bal. Small amounts of boron and zirconium were added to certain heats as listed in Table I. These additions

Jan 1, 1959

Report of the Secretary TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTI¬TUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining in¬dustries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has re¬stricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metal¬lurgy have a greatly increased necessity for information and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowl¬edge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrollment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1923

By Robert H. Richards

This is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. Causes oF Loss in ORe-ConcEntration. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of loss that are likely to interfere with the concentration. Having made this definition, we can then study to see in what may the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take these up one by one, as follows: Included Grains.—Fig. 1 shows by a set of diagrams how included grains may occur : first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to the furnace, or poor enough to throw away, or whether they lie between these two points and require recrush-ing as the only means of severing the values from the waste. This last case is the orlly one requiring special treatment at our hands. We will therefore consider that next.

Jan 1, 1911