Search Documents

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,' but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick's law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

By J. Chipman, N. J. Grant, E. C. Roberts

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-Si02-FeO-Cr& type in the temperature range 1526' to 1734OC. The effects of slag oxidation, temperature, and basicity were observed. IN spite of the fact that chromium is one of the most important alloying elements in steel, and exists in almost all steels as a significant residual element, little research has been done to determine its behavior in basic steelmaking processes. Considerably more work has been done under silica-saturated acid slag conditions. Korber and Oelsen,' Herasymenko,' and others have generally agreed that in acid steelmaking practice the chromium in the slag behaved as if it were present as the chrom-ous ion (CrO). Work by Hilty- ir, high chromium slags also indicated that chromium may exist as CrO. In basic slag systems no equilibrium data exist. Based on individual studies of basic open hearth and electric furnace practice, Bardenheuer," Rock-rohr,% nd HauckQ oncluded that: 1—chromium recovery increased with decreasing basicity, and 2— chromium recovery increased with increasing temperature, although the effect was small. In similar studies Yavioskii and Dzemyen' concluded that: 1— slag FeO is the most important variable, 2—the basicity of the slag has no effect on chromium recovery, and 3—slag viscosity is not high even when 20 pct Cr,O, is present. Lapitskii\ oncluded that chromium recovery improved as the basicity of the slag decreased and increased with increasing manganese in the metal. Regarding the effectiveness of CrZ08 as a base or acid in basic slags, both Kristofferseno and Trojer" reported that Cr,08 was an acidic component requiring neutralization as 2CaO-Cr,O,. Experimental Procedure The experimental apparatus and procedure used for the present research were similar in most details to those used by Winkler and Chipman" and were described in detail by them. A magnesia crucible was used, holding 60 to 80 lb of Armco iron which was decarburized with hydrogen to about 0.010 pct C. Since all the metal samples solidified without gas evolution, this carbon level was assumed not to be significant. Synthetic slags made by mixing pure oxides were used throughout the study. Temperatures were measured by means of calibrated W-Mo thermocouples and were checked by Pt-Pt-Rh thermocouples. The range of temperatures covered in this study was from 1526" to 1734°C. The chromium content of the iron was in the range 0.032 to 0.82 pct, although the bulk of the tests showed 0.04 to 0.2 pct. The slags were of the CaO(MgO)-SiO,-FeO-Cr,O, type in which the Cr,O, content was from about 2 to 20 pct, although most of the slags showed from about 2 to 10 pct. The FeO range was from about 10 to 65 pct. CaO and SiO, were in the range of about 5 to 45 pct each, yielding a rather wide range of basicity values. The first 12 heats were made without a sulphur addition, and with only 30 min allowed for slag-metal equilibrium to be reached. In previous research it had been shown that less than 30 min was adequate to achieve equilibrium in slags free of Cr2O8.11,14.15 A study of the present data indicated that some of the tests may not have reached equilibrium in this time; accordingly four additional heats were made in which at least 1 hr was permitted for equilibrium to be reached. For reaching

Jan 1, 1955

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.'.' While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham's law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By W. M. McKewan

A large amount of work has been reported in the literature on reduction of cubes, spheres, or regularly shaped particles of iron ore. Previously, it has been difficult to evaluate these data because no equation has been developed that would yield one or more constants for comparison of overall reduction rates. Iron ore in the process of gaseous reduction is a complex system. The reduction takes place through the series Fe2O3-Fe304-Fe0-Fe. Edstrom and Bit-sianesl have reported that the gas-solid type of reaction was found only at the FeO-Fe interface and that the internal reduction proceeded by elementary diffusion of iron. Therefore, during reduction oxygen is essentially removed from the system only at the FeO-Fe interface. Kinetically, it is reasonable to consider iron ore in the process of reduction as a

Jan 1, 1959

By Arthur C. Simmons

The area that produces Pennsylvania grade, which includes New York, Pennsylvania, West Virginia and a part of Ohio, increased its production in 1942 about 1,580,000 bbl. over that attained in 1941. Such an increase is substantial for this area, and measured in terms of increased output of lubricants, for which the crude is particularly suitable, it represents a needed arid worth-while addition to the lubricant resources of the United States. The year 1942 was a difficult operating period for most of the petroleum-producing areas in the United States, but the Appalachian region, owing principally to its location, type of operations, and crude value, suffered less from war influences than other areas. The state of Pennsylvania produced 17,823,870 bbl. of crude oil, which is approximately 63 per cent of the total production of Pennsylvania grade in the entire area. Production Bradford Field The Bradford field, which produces almost wholly by water-flooding methods, increased its production nearly 4000 bbl. per day over 1941 despite a very slight reduction in total number of wells completed. Well completions in the Bradford field (in both New York and Pennsylvania) includc both producing oil wells and water-intake wells. About half of the well completions are producing oil wells and the remaining half are water-intake or injection wells. About 10 per cent of the total well completions of the Bradford field were in Cattaraugus County, New York. No segregation of well completions is available, so that precise statistics cannot be given for New York and Pennsylvania.

Jan 1, 1943

By Arthur C. Simmons

The area that produces Pennsylvania grade, which includes New York, Pennsylvania, West Virginia and a part of Ohio, increased its production in 1942 about 1,580,000 bbl. over that attained in 1941. Such an increase is substantial for this area, and measured in terms of increased output of lubricants, for which the crude is particularly suitable, it represents a needed arid worth-while addition to the lubricant resources of the United States. The year 1942 was a difficult operating period for most of the petroleum-producing areas in the United States, but the Appalachian region, owing principally to its location, type of operations, and crude value, suffered less from war influences than other areas. The state of Pennsylvania produced 17,823,870 bbl. of crude oil, which is approximately 63 per cent of the total production of Pennsylvania grade in the entire area. Production Bradford Field The Bradford field, which produces almost wholly by water-flooding methods, increased its production nearly 4000 bbl. per day over 1941 despite a very slight reduction in total number of wells completed. Well completions in the Bradford field (in both New York and Pennsylvania) includc both producing oil wells and water-intake wells. About half of the well completions are producing oil wells and the remaining half are water-intake or injection wells. About 10 per cent of the total well completions of the Bradford field were in Cattaraugus County, New York. No segregation of well completions is available, so that precise statistics cannot be given for New York and Pennsylvania.

Jan 1, 1943

By C. O. Bundranl, Peter Dehlinger, W. H. Browne

Brief laboratory investigations are described which attempt to determine optimum .sand concentrations in gel-sand and oil-sand1 well-treatments. The investigations apply to the case where sand acts as a propping agent in formation fractures. Both analytically and experimentally it is demonstrated that optimum sand concentrations can be defined. It is difficult to translate laboratory results to field treatments, however, since the relative distribution of sand and fluid in fractures may not be the same as injected. This is because fluid may penetrate the furtherest narrow portions of fractures, which would not pass sand. Optimum concentration of a monolayer of Ottawa sand in fractures of 0.025-in. width at the usual range of pressures encountered in treatments appears to be about 95 to 2 lb/gal. of gel. An investigation of abrasion of rock-walls by sand in treatments, described in the Appendix, shows that such abrasion is not probable in significant amounts. INTRODUCTION Experience in the Spraberry formation of West Texas, as well as in other formations, has shown that. sand is a necessary and vital part of gel-sand and oil-sand treatments. Many observers of treatments have also concluded that there seems to be an optimum range of sand concentration for these injections. Brief laboratory investigations were made at Battelle Memorial Institute to study flow in fractures with different sand concen- trations. To investigate the existence and range of optimum concentrations in the laboratory, however, necessitates knowledge of the mechanism by which the sand aids in increasing subsequent production. The action of sand in fractures is usually thought to be either that of a propping agent, thus providing a greater effective formation permeability; that of an abrasive in eroding fill material in fractures; or that of an abrasive eroding rock-wall irregularities along fracture surfaces. Investigations described in the Appendix show that sand does not appear to erode rock-wall materials appreciably. In a subsequent paper it is reasoned, at least for the Spraberry formation of West Texas, that the primary action of sand is not in removing fill materials in fractures. In this formation, and probably others, too, the main effect of sand appears to be that of a propping agent. Both analytical and experimental investigations were made for the case of a monolayer of sand acting as a propper, in which sand concentrations were determined that would, after treatment, permit flow of the maximum quantities of oil from the formation into a well. If too few sand grains are injected into fractures in which the bottom hole pressure has decreased appreciably below the original formation pressure, the confining pressure in the formation may become relatively large, thus compress the rock-walls around the sand grains, essentially close fractures, and so decrease the subsequent flow of oil. Similarly, if too much sand is used, the flow of oil will he impeded by the volume of sand present. THEORY Although an analytical approach to determining optimum sand concentrations involves gross assumptions.

Jan 1, 1955

By A. W. Fahrenwald

THE function of the classifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred tows "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particular method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted.

Jan 1, 1930

By R. H. Martinson, E. Teghtsoonian

The effects of magnesium-rich surface layers of varying thickness on the mechanical properties of LiF have been studied. The yield stress, critical tensile stress, and work-hardening slope increase linearly with layer thickness, while the strain to fracture decreases yapidly with increasing layev thickness. The results of tension tests, supplemente!d by metallogvaphic evidence, indicate that the yield stress and the critical tensile stress of LiF are not determined by surface-source operation. DESPITE many studies, which have recently been reviewed,' certain fundamental aspects of the plasticity of LiF remain obscure. For instance, one question still awaiting a satisfactory resolution is: does the nucleation and/or multiplication of dislocations in LiF occur preferentially near the crystal surface? It is now well-known that mobile dislocation half-loops are readily introduced into LiF by surface damage and that the mechanical properties of LiF are affected by such surface damage. However, it is not known whether, in the absence of large numbers of artificially introduced surface sources, dislocations arise more easily near the crystal surface than in the crystal interior. It is also not known to what extent existing mobile dislocations multiply preferentially near the crystal surface. The present work is an experimental study of these matters. A short investigation of the effect of magnesium -alloyed surface layers on the deformation of LiF single crystals has been published by Westwood.~ Some relevant conclusions drawn from this research are restated here for purposes of comparison with the present work. 1) Tests on as-cleaved, chemically polished, coated and uncoated specimens show that a coating can restrict the operation of artificially introduced surface sources, thereby raising the yield stress. A coating also decreases the initial rate of work hardening of as-cleaved LiF crystals by reducing the number of active dislocation sources, so that mutual dislocation interference effects are lessened. 2) A catastrophic breakthrough of groups of edge dislocations piled up against the coating can cause stress drops in the stress-strain curve. 3) A surface coating can act as a stable barrier to the egress of dislocations, causing pile-up,

Jan 1, 1965

By P. Somasundaran, R. D. Kulkarni

Reagentizing at elevated temperature, reported in the past as beneficial for the flotation of hematite using oleate, is studied here as a function of collector concentration, solution pH and ionic strength at various levels of conditioning temperature. The study revealed strong interactions between variables; particularly, the effect of conditioning temperature was found to strongly depend on the ionic strength of the solution. Thus, while an increase of conditioning temperature at lower ionic strengths or that of ionic strength at lower temperatures resulted in an increase of both flotation and grade, an increase of the former at higher ionic strength or that of the latter at higher temperatures caused a significant decrease in both responses. These observations have been explained in terms of the increased chemisorption of oleate at elevated temperatures and the temperature effect of ionic-strength on the salting out of the oleate from the bulk solution. The above effects which were first observed during Hallimond cell flotation tests were subsequently tested with Denver cell using low-grade iron ore. The results obtained using the two test procedures were in agreement with each other. The implications of these effects and interactions for process control of optimum flotation performance must be noted since variation in the levels of the above parameters are likely under plant conditions.

Jan 1, 1978

By W. W. Svendsen, J. F. Hoffmeister, W. C. Larson, R. E. Cozad

The paper presents the background, history, and current development of the retractable core bit for the wireline drilling system. Design criteria, concept development, and system design of the retractable bit system are discussed, including laboratory test results.

Jan 1, 1983

By Stephen Krickovic

AS it is commonly understood in the bituminous coal mining industry, pillaring means removal, as completely as is practical, of all pillars formed in the development of headings and rooms on first mining. The degree to which this can be accomplished, termed percent of recovery, is of course dependent generally upon the physical conditions of the bottom and the overburden, the system of min-

Jan 1, 1956

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of

Jan 1, 1938

For the first time in its history the Institute will hold a meeting in the State of Arizona. A few years ago Arizona stood third in the copper-producing districts of the United States. Since that time, with the development of porphyry mines, the output has gone up with great rapidity until it not only is the leading district, but its output at the present time is at the rate of nearly double the Montana output, which now stands second in the list. In connection with this .development, most interesting departures have been made in methods -of mining, concentration and smelting. Principles of mining and metallurgy of the greatest interest will be covered by papers which will' appear in the Bulletin and be presented at Technical Sessions, while ample opportunity will be afforded for those who go to the meeting to see all the points of interest .to them. In addition, members will be well rewarded by the marvelous natural features to be seen on the trip, including 'the petrified forests, the cliff dwellings on the Apache Trail and the Grand Canyon of Arizona. It is planned to start the special train from New York, but members and guests may join the special at other points en route as indicated by the following schedule: ITINERARY . , Thursday, September 14th Lv New York, Grand Central Terminal.. ............... 5.30 p. m. Dinner in dining car a la carte New England Members via B. & A. R. R. . Lv Boston. ............. (Regular train). ............. 2.00 p. m. Lv Worcester. ........... (Regular train). ............. 3.12 p. m. , Lv Springfield. ........... (Regular train). ............. 4.37 p. m. Dinner in Dining Car a la carte Ar Albany.. ......... .New York Central R. R.. ....... 7.45 p. m. Lv Albany .......................................... 9.00p.m. Lv Schenectady.. .................................... 9.32 p. m. Lv Utica ............................................ 11.08~.

Jan 8, 1916

W. H. PORTH, New York, N.Y.-I would like to ask what effect segregation of lead would have upon the corrosion of sheet zinc; also what effect would abnormal percentages of iron have upon the ductility of Sheet zinc? One of our difficulties seemed to be that the cells, when standing on the shelf, corroded. We have attributed this to local action in the zinc sheet. We would like to know whether the segregation of, these impurities in this sheet zinc will have any effect on the local action occur-ring in sheet zinc. Lately we have had difficulty in punching some sheet zinc, in that the sheets split in the die. The section that split seemed to have an abnormallly high percentage of cadmium and iron; would that cause it to become brittle? C. H. MATHEWSON.-Iron is one of the most unwelcome impurities when high ductility is the principal requirement in rolled zinc. High

Jan 12, 1919

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) THE tabular statement accompanying this note shows the money cost in each of the three departments of manufacture, of 17 leading items, and also the proportion (expressed in a decimal fraction) which each of these items bears to the total cost. The statement can hardly be taken for more than an average illustration of the clear showing of ratios and of results which may be made by such an arrangement, for not only will these items vary from month to month in any given works, but the methods themselves of manufacture differ widely in different works. It is obvious that such a statement, however useful it may be, must be submitted with but exceedingly little explanation or discussion, or with none at all, for the reason that to enter at any satisfac-

Jan 1, 1878

By R. V. Wheeler

A MATTER of much concern at present to the coal-mining industry of-Great Britain is the effect of the working of the Coal Mines Act, 1930. This Act, which received the Royal Assent on Aug. 1, 1930, contains five parts: (I) production, supply and sale of coal; (II) the reorganization of the coal-mining industry; (III) hours of work; (IV) the Coal Mines National Industrial Board; (V) general. The first three parts are of major interest and discussion can be confined to them.

Jan 1, 1931

By J. B. Dilworth

The purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resourcee, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigatioil pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnois-sance was attempted: such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their

Jan 1, 1913

By Victor O. Strobel

Fire-brick hot-blast stoves have been the subject of frequent discussions at the meetings of the Institute; and although it is my object to elucidate some of the points in connection with this subject, I will not go into the specific features of all types, but more especially call attention to a new type recently designed by Mr. Fred. W. Gordon. As the economical production of a ton of pig-iron is a more essential feature than a large output, much depends, where fuel cannot be obtained cheaply, upon suitable apparatus whereby high temperatures can be maintained. Where iron-pipe stoves have been employed, the fuel-consumption reached one and a half pounds of fuel, and, when a larger output was desired, often two pounds, to the pound of iron produced. The temperature attained rarely exceeded 900' F., and that at the expense of frequent renewals of the pipes, which was not inconsiderable. The fire-brick hot-blast stoves of the past five or six years have clearly demonstrated their superiority over the old system. Of the accompanying drawings, Fig. 3 illustrates a four-pass regen-

Jan 1, 1886