Search Documents

By N. Arbiter, C. C. Harris

In 1961, a research program started at Columbia into the mechanical aspects of flotation,* and certain ends are now in view. The purpose of this note is to explain these tentative conclusions in the hope of stimulating discussion and eliciting new data, especially industrial data, with which to test the views expressed. The variables presently under consideration are impeller rotational speed, N, volumetric air rate, Q, and impeller diameter, D, the latter being the parameter chosen to designate cell size. The most favorable *The latest work 1 references all previous publications. chemical environment is not under discussion since the procedures for establishing it are better understood than those for optimizing N and Q by virtue of a longer history of more intensive investigation. THE GRADE AND RECOVERY SURFACES With a given ore, chemical treatment, and flotation machine, both grade, G, and recovery, R, are functions of N and Q. The GNQ and RNQ relationships are best viewed in terms of three-dimensional surfaces (Fig. 1) which are experimentally determinate.2 TO maintain grade at an acceptably high level, it is necessary for N and Q to lie within certain limits, and similarly with recovery. However, the ranges of N and Q for grade on the one hand and recovery on the other are rarely the same. Selecting the single N

Jan 1, 1970

By M. L. Jeremic

The massive Pb-Zn-Ag sulfide ore body is originated at the contact between the porphyry (footwall) and volcanic (hanging wall). The ore zone is folded and refolded, which results in two different structural geometries of the individual ore bodies. This requires both shrinkage and cut-and-fill mining methods. Strong bedrock resists caving after shrinkage stope completion, so high stress zones are developed below and above the mined area. The cut-and fill system has a limited destressing mechanism, where the stope walls with a backfill exhibiting stress close to a primitive one. This results in closure deformation of the open stope walls, yielding deformations of crown pillars and roof falls of the wide stope backs.

Jan 1, 1985

By M. L. Hammond, G. M. Bowers

Silicon dioxide films have been prepared on silicon wafers by the oxidation of SiH, near 400°C. Results previously reported by Goldsmith and Kern7 have been qualitatively corrobovated using a system of different geometry, and significantly greater deposition rates have been achieved. The deposition rate is independent of thickness and nearly independent of the O2/SiH, ratio over a wide range; however, the rate is strongly temperature-dependent. The structure of the deposit depends upon the cleanliness of the substrate, and the electrical field strength of the deposited oxide depends upon the nature of the electrodes. MULTILEVEL interconnects in integrated circuits using aluminum metallization require an insulator that can be deposited at low temperature. Because the A1-Si eutectic is only 577°C, the maximum deposition temperature must be below about 500°C to prevent reaction of the aluminum with the silicon and with other materials in the integrated circuit. Many methods of depositing insulating films of SiO, and other dielectrics have been reported'-6 but the technique described by Goldsmith and Kern7 offers the simplest method of preparing SiO, films. The technique involves the reaction of SiH, and 0, to form SiO, films in the 300" to 500°C temperature range. Previous work using this gas system has been reported8 and the initial development work at Philco Microelectronics was done at the East Coast R&D Laboratories. 9 This paper corroborates some of the results of Goldsmith and Kern,7 shows that much higher deposition rates can be obtained than previously reported, and presents some observations on the structure of deposited SiO, films. EXPERIMENTAL CONDITIONS Fig. 1 is a schematic drawing of the apparatus used in this study. It differs from that of Goldsmith and Kern in that 1) the gases are mixed before they enter the reaction chamber, 2) there is no fritted glass diffuser, and 3) the wafers are stationary during deposition. The control thermocouple was in a well located 0.06-in. from the substrate, and three gas supplies were used: 1 pct SiH4 in N 2, O 2, and N 2. Water vapor must be excluded from the plumbing to prevent the formation of colloidal SiO, and the SiH4 must be diluted with an inert gas because SiH4-0, mixtures are extremely flammable above about 4 pct SiH The wafer temperature was determined by attaching a thermocouple to a test wafer and the temperature was maintained to +5 C. The conditions used in this investigation are listed in Table I. The temperature range was chosen for compatibility with the A1-Si system. The volume ratio of 0, to SiH4 is the actual volume of 0, delivered to that of SiH4, taking into account the initial dilution of the SiH4. This ratio, which was used by Goldsmith and Kern,7 is a useful indicator of the experimental conditions. The active/inactive ratio is the ratio of the volume of active gases, SiH4 and O2, delivered to the volume of dilution gas. The active/inactive ratio is an important parameter to specify for deposition rate determinations since it determines the amounts of reactants that arrive at the sample per unit time. Fairly high dilution ratios were necessary to achieve uniform deposits of SiO,. Most of the process characterizations were performed on the polished (111) face of 3 to 5 ohm-cm, n-type silicon wafers which were 0.009 in. thick; but the data approximately apply to deposition of SiO, on thin films of aluminum. It is difficult to obtain accurate deposition rate data over aluminum films because of coarsening the aluminum surface during exposure to 300" to 400°C. The deposited SiO, film fol-

Jan 1, 1969

By H. Margolin, E. Ence

A. J. Goldak and J. Gordon Parr University of Alberta) —Margolin and Ence's paper reached us only a few days after we had submitted a paper on the structure of Ti2Cu to the AIME. Here, however, we only wish to point out an error in the paper (page 321): "Karlsson has reported the crystal structure of the first intermediate phase occurring in the Ti-rich portion of the Ti-Cu system to be face-centered tetragonal." Karlsson actually reported the structure of Ti3Cu (i.e., "the first intermediate phase") to be primitive tetragonal with four atoms per lattice point: Cu at 0, 0, 0; and Ti at 1/2, 1/2, 0; 0, 1/2, 1/2; and 1/2, 0, 1/2. Thus, Karlsson suggests a primitive lattice with an ordered arrangement of atoms located at corners and face-centers: Ence and Margolin suggest a random body-centered tetragonal structure—-with which our results agree. E. Ence and H. Margolin (azlt1zo.l-s' reply)— We do not agree that Karlsson has not reported the structure of Ti3Cu as face-centered tetragonal. The fact that Cu atoms are located at the corners and titanium at the face-centers does not indicate that the lattice is not face-centered. We are pleased that the discussers' results agree with our own.

Jan 1, 1962

By H. Guyod

The response of the Guard Electrode sonde (LL3) and the Laterolog (LL7) can be mathematically computed only for cases that do not represent realistic conditions. A resistance network analogue that simulates a number of typical—although idealized—formations was used instead to obtain, for both devices, a large number of resistivity logs and current distribution maps. From these data, charts were prepared for estimating true resistivities under a number of conditions. Some of these charts and current distribution maps are presented. INTRODUCTION Two main benefits are expected from a resistivity log: (1) obtaining geological information for mapping and other purposes, and (2) obtaining petrophysical data, based on true rock resistivity. The geological information can be derived from any resistivity curve having sufficient vertical detail, but true rock resistivities frequently are difficult to determine with desired accuracy because we do not have sufficient interpretation data. This is particularly true for the records given by the Laterolog tools. The object of this paper is to throw some light on the factors affecting the responses of these tools so that better resistivity data can be obtained from Laterologs. LATEROLOGS Laterolog measuring systems are of two types: the LL3 sonde, frequently called "Guard", and the LL7 sonde. Both measure the resistance between a single exploring electrode placed in the borehole and a faraway return electrode whose influence will be assumed here to be negligible. Although the principles of these tools have already been outlined,1-3 it is desirable to review them briefly in this article. LL3 Fig. 1, left side, represents a long cylindrical, vertical current electrode placed in a medium of uniform resistivity. The current leaving the center section of the electrode flows essentially along horizontal lines, delineating a surface having the shape of a biconcave lens. It is the elec- trical resistance offered to this particular group of current lines that is measured by the Guard tool. This is done in practice by having a long cylindrical electrode consisting of three sections physically and electrically separated by thin insulating washers, as shown in the center of the figure, and keeping the three sections at the same potential. It is obvious, for all practical purposes, that the current and potential distributions about this electrode are the same, as if we had a continuous electrode of same dimensions. Because the three sections are electrically separated, the resistance seen by the center section E can be independently measured. This section will be called the exploring electrbde, or E electrode. Its height generally is from a few inches to 1 ft. The outer sections are the guards G, which are several feet long. The combined length of the three sections is from 10 to 12 ft for the tools currently used in the petroleum industry. Let V denote the potential difference between E and the faraway return electrode, and I be the current flowing between these two electrodes. The resistance (Re) seen by the exploring electrode is VII, and the corresponding apparent resistivity is Ra = k(Re),............(1) where k is the tool calibration factor. The previous description establishes that the Guard tool uses that central portion of the sonde from which, in a uniform medium, the current follows essentially horizontal paths. When the formation being logged is fairly uniform, and when its resistivity is of the same order as

Jan 1, 1965

By B. R. Palmer, G. Gutierrez B., M. C. Fuerstenau

Flotation responses of chrysocolla and rhodonite are correlated with electrophoretic mobility and infrared spectroscopy measurements. Flotation is effected in the pH ranges in which hydrolysis of the metal ions comprising the mineral occurs. The roles of mineral solubility and precipitate formation are suggested.

Jan 1, 1976

By H. Conrad, K. Janowski, G. Stone

The available data on the dynamics of plastic flow of sapphire indicate that the deformation rate in the temperature range .from 900° to 1700°C can be expressed either as A number of investigators1-10 have established that sapphire deforms plastically above 900°C, the most common mode of deformation being slip on the basal plane in the [1120] direction. Under certain conditions and at temperatures above 1500°C, slip

Jan 1, 1965

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is undcrlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production

Jan 1, 1938

By B. E. Thompson, H. B. Fuqua

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By B. Wilshire, W. J. Evans

The high-temperature creep properties of nickel, zinc, and iron have been determined over a range of stresses. The creep strain, E, was found to vary with time, t, as: where e0 is the instantaneous strain on loading, ET the total transient creep strain, $ the steady creep rate, and m is a constant relating to the rate of exhaustion of transient creep. Deviations from this relationship occurred during the initial 10 to 15 pct of the transient stage. These deviations result in the initial creep rate, go, calculated as (m . ET + es), being considerably lower than those obtained by measurements on the creep curve. For all materials, the initial creep rate, the constant m, and the duration of transient creep are all related to the steady creep rate. These relationships suggest that transient and steady-state creep should not be regarded as distinct stages.

Jan 1, 1969

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner's Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe's gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958

By Lawrence H. Van Vlack

DISCUSSION, H. L. Burghoff presiding C. S. Smith (University of Chicago, Chicago)—The author is to be congratulated on his valuable contribution to the extremely meager absolute data on interface energies in metallic systems. It is interesting to note that the ratio between a and r iron boundary energies is approximately the same in the quaternary alloy with silicon, carbon, and sulphur as in the binary Cu-Fe alloy. A value for the copper grain boundary energy can be obtained from the author's data, Tables IV and VI, by utilizing the energy ratios of the following pairs of interfaces: copper-sulphide/copper, copper y iron, y iron/y iron, y iron/ copper, and copper/copper. This gives a value of 595 erg per sq cm for the free energy of the copper grain boundary. Despite this circuitous route and the assumption that the y iron boundary is identical in alloys with and without sulphur and does not change between 1105" and 100O°C, this figure is in remarkably close agreement with other values of the copper boundary energy, obtained by equilibration against lead and against the free copper surface. It therefore appears either that impurities do not greatly affect the grain boundary energies or that boundaries in even nominally pure metals are already sufficiently contaminated so that further change has little effect.

Jan 1, 1952

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By A. Hultgren, B. Herrlander

The original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between A1 and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880' was free from veining. Bannister and Jones' considered veining in ferrite to be a manifestation of microscopical and sub-microscopica~ inclusions. NorthCOtt,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berg1und. TrittOn (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling. Slight distortion would not allow projecting parts of a growing crystal to join up with atomic symmetry. Hanemann and co-workers showed that veining in ferrite consisted of ridges

Jan 1, 1948

By B. Herrlander, A. Hultgren

The original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between A1 and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880' was free from veining. Bannister and Jones' considered veining in ferrite to be a manifestation of microscopical and sub-microscopica~ inclusions. NorthCOtt,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berg1und. TrittOn (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling. Slight distortion would not allow projecting parts of a growing crystal to join up with atomic symmetry. Hanemann and co-workers showed that veining in ferrite consisted of ridges

Jan 1, 1948

By A. J. Griest, P. D. Frost, H. A. Robinson

The flow characteristics and uniform elongation of alpha-beta titanium alloys in the solution-treated condition were shown to be markedly affected by the solution temperature. Two classes of alpha-beta alloys were distinguished, based on the effect of solution temperature on the uniform elongation. Martensitic alpha-beta alloys, which are relatively weakly beta-stabilized, showed decreasing values of uniform elongation as the solution temperature was initially increased. However, after solution-treatment at still higher temperatures in the alpha-beta field, the uniform elongation of these alloys was again high, and often attained its maximum value. Nonmartensitic alpha-beta alloys, which are more heavily beta-stabilized, showed a continuous decrease of uniform elongation with increasing solution temperature. The behavior was rationalized in terms of the alpha-beta ratio and the alloy content of the beta existing at the solution temperature. The data indicate that in commercial practice close temperature control may be required to get maximum uniform elongotion, and hence, maximum potential formability, in solution-treated sheet. Bend-test data also were obtained for the solution-treated conditions. A MOST important objective of current titanium research is the development of age-hardenable alloys with superior formability in the solution -treated condition. Alpha-beta titanium alloys have been shown to be amenable to high-strength aging treatments after solution-treatment in the alpha-beta field.' However, heat-treatment data on the properties of solution-treated sheet, such as uniform elongation, minimum bend radius, and flow properties, which have a bearing on the potential formability, have not been widely available. This paper presents only the most significant results of a research program conducted at Battelle for the Air Force in an effort to develop sheet alloys that can be formed readily as solution-treated and subsequently aged to very high strengths. Data for 10 compositions representative of the more than 25 alloys studied in this program are presented. A primary objective of the paper is to demonstrate the pronounced dependence of the flow characteristics and uniform elongation on solution-treatment temperature. This effect is believed to be vitally important in the commercial heat-treatment of age-hardenable titanium sheet alloys. Experimental Procedures Melting and Fabrication—The nominal and actual compositions, beta transi temperatures, and rolling temperatures of 10 of the 30 alloys studied are presented in Table I. Stock :€or two of the alloys, E (Ti- 8Mn) and J (Ti-6A1-4V) was obtained from commercial heats. The remaining heats, except D and I, were double melted as 10-lb heats in a consumable-electrode furnace. Melting stock was 120 Brine11 hardness sponge. The oxygen and hydrogen analyses spotted throughout the heats indicate the range of interstitial levels resulting from the melting practice used. Heats D and I were melted as 20-lb ingots with the same grade of sponge. These ingots were cut in half and one portion used in the present evaluation. The ingots, which were about 4 in. diam and 4 in. in height, were upset forged and drawn at 1750°F to sheet bar 5/8 in. thick by 2 1/2 in. wide in such a manner that the top of the ingot corresponded to the top of the sheet bar. Slabs of the sheet bar, 5 1/2 in. in length were scalped to 1/2 in. thickness and rolled at the temperatures indicated in Table I to approximately 0.055 in. sheet. Elongation during rolling took place at 90" to the original forged length. The fabrication procedure used is described in some detail since the experimental heats showed considerable directionality in mechanical properties. The rolling procedures for the commercial heats were unknown, but were such as to produce essentially isotropic properties. All heats, as rolled, showed microstructures typical of alpha-beta alloys worked in the alpha-beta field; that is, the structures consisted of equiaxed alpha particles in a beta matrix. Heat Treatment— The effects of solution and aging heat-treatments on the properties of the alloys were evaluated uSing longitudinal and transverse tensile and bend coupons sheared from the sheet. Two or three solution-treated conditions were evaluated for each alloy. In addition, the alloys were also tested after annealing at 1200°F for 4 hr and furnace cooling. The solution-treated and annealed conditions were those in which the alloys might be expected to

Jan 1, 1959

By B. D. Cullity

This investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy—the thermoelectric efficiency—has been discussed by Telkesl in a recent review of the subject. She gives the thermoelectric efficiency as: W o Efficiency = -Wo ______________i____________ TR-TC+ O2TR-Tc) where W, = power output in external load (watts) Wi = rate of heat input to hot junction (watts) TE,T, = temperature of hot and cold junctions (oA) K1,Kz = thermal conductivity of the two thermocouple materials (watts/cm°C) p,,pz = electrical resistivity of the two thermocouple materials (ohm cm) 9 = thermoelectric power (volts0/C) For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of pfoperties. Bismuth-selenium Alloys work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson who gives the diagram reproduced in There are two intermediate phases in this system, BiSe and Bi²Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedra1 crystal

Jan 1, 1949

By L. C. McCabe

This paper is a progress report on a study of the distribution of the banded ingredients (Figs. 1 and 2) in Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screenings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57 whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample. The relative proportions of the banded ingredients in the Herrin (No. 6) coal in Illinois is reasonably well known but detailed information

Jan 1, 1936

By L. C. McCabe

This paper is a progress report on a study of the distribution of the banded ingredients (Figs. 1 and 2) in Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screenings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57 whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample. The relative proportions of the banded ingredients in the Herrin (No. 6) coal in Illinois is reasonably well known but detailed information

Jan 1, 1936