Search Documents

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By Howard N. Eavenson

TWO months ago, just after the coal code hearing in Washington, one of our leading liberal weeklies printed a study of the coal industry made by an economist in the Administration, and on the outside cover bad it featured as "Coal-A Dying Industry." There are, of course, different opinions as to the accuracy of this characterization and I want to present some of the facts about the outlook for the bituminous industry for a short time ahead. In view of what has happened in the industry within the recent past it would be futile to attempt to make any prophecy about what is likely to occur in the future. We all know that a prophet is not without honor save in his own country, but it is likely that anyone undertaking this role about this industry would soon find himself in no man's land. One can, with some slight degree of safety perhaps, outline present conditions and tendencies and draw some inferences as to what the future may hold.

Jan 1, 1933

Jan 1, 1969

By John M. Loveioy

EVERY producer of crude oil knows what is meant by the Rule or Law of Capture. It means that the ultimate ownership of a migratory substance such as oil is not determined until that substance is reduced to physical possession. Unless, therefore, the producer moves quickly to capture his share from the common pool, he may lose to any neighbor who is drilling and producing more rapidly than he a portion of the oil originally underlying his property. And there is no recourse open to him if his property is so drained. Under this rule it is obvious that the owner of an oil property, if he is to protect his' ownership, must be governed in his development and production policies by the activities of his neighbor rather than by his own business requirements. He must drill as densely and as fast as the other operators in the field or lose part of the oil to which he should be entitled.

Jan 1, 1936

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By R. A. Wattenbarger, H. J. Ramey

The trend in gas well testing has been to rely more on the early-time flow data of drawdown and buildup tests than on stabilized flow tests. The stabilized testing methods often are not adequate for complicated modern gas reservoirs because many of these reservoirs have extremely low permeabilities and the transient flow period of a well test can last for days or weeks. It has become common to augment the flow capacity of gas wells by hydraulically fracturing their producing formations. In deep reservoirs the induced fractures are generally vertical and tend to follow a single plane of weakness. The presence of a vertical fracture at the wellbore complicates the transient flow behavior of a low permeability gas well. The flow is further complicated when turbulence occurs near the wellbore. Russell and Truittl published transient drawdown solutions for vertically-fractured liquid wells. They developed methods of drawdown and buildup testing utilizing these solutions, which were based on numerical simulation. Clark2 applied the basic Russell-Truitt solutions to analyze fractured water injection wells by falloff tests. Field examples were given to substantiate the method of analysis. The Russell-Truitt solutions and well testing methods can be extended to gas well flow. Millheim and Cichowicz3 presented the drawdown equations for *Now with Scientific Software Corp., Denver. ideal gas flow, including the effects of formation damage and turbulence. Two actual field cases were presented, both of which exhibited extensive fractures and turbulent flow. For the pressure range of these well tests, the use of ideal gas equations was acceptable. These field cases were significant in being the first published data showing the occurrence of turbulence in fractured gas wells. We, also, observed such cases in practice. Our purpose here is to extend the theory of fractured gas well testing to the flow of real gases. To determine the effects of wellbore storage and turbulence on well test interpretation, we developed a finite-difference model to simulate well test conditions. Since gas wells usually are widely spaced and have high compressibility, the emphasis has been put on the early transient behavior before the effects of the outer boundary are noticeable at the wellbore. The Mathematical Model The geometry of our mathematical model is similar to that used by Prats.4 The well is centered in a circular uniform reservoir. A vertical fracture of infinite flow capacity penetrates the formation and passes through the wellbore. The wellbore itself is not important. Fig. 1 shows a sketch of the problem. Fig. 2 shows the idealized model. The equation for the flow of real gas in a porous medium with uniform porosity, permeability and thickness is5-7

Jan 1, 1970

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By AIME AIME

THE MODEL LAW previously referred to', in these columns several times, prepared by Engineering Council, to be o ered in any state where legislation is introduced for licensing engineers, is given in abstract below. , Mining engineers throughout the country should watch legislation of this sort and see that the draft prepared by Engineering Council is in the hands of any state legislative committee which proposes to frame a licensing law. So far as this office is informed, the mining engineers are a unit against licensing, but if we must be licensed the most innocuous law that has been submitted is the draft prepared by Engineering Council. ABSTRACT OF MODEL LAW -FOR REGISTRATION OF PROFESSIONAL ENGINEERS, ARCHITECTS, AND LAND SURVEYORS

Jan 1, 1920

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By G. H. Cutter

SAFETY in mining depends on wire rope to as great, if not greater, extent than in any other industry. Sudden failure of a shaft-hoist rope might easily result in death or serious injury to the operators and workmen, extensive damage to expensive equipment, and a loss in production while repairs are being made. A wire rope is only as good as its component parts. It must be made from wire properly drawn and treated. It must be fabricated on machines large enough and capable of imparting the necessary qualities to meet the stringent service conditions. However, unless the fundamental requirement of good ropemaking is recognized, all other operations, no matter how carefully performed, will not impart reliability and quality to the product. This fundamental requirement is steel that is homogeneous, of high resistance to fatigue, and of a type suitable for rope wire. Most wire-rope manufacturers agree that rope wire should be made from acid-open-hearth steel. It is comparatively easy to meet the same physical properties with basic steel, but such properties are only part of the requirements for good wire. It is absolutely necessary, particularly for rope service such as mining, where reliability is essential, that the wire be uniform throughout its entire length. Most manufacturers feel that this highly important requirement is better met by acid-open-hearth steel.

Jan 1, 1936

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By Arthur A. Center

WAR demand- motivated developments in the zinc industry during 1942. Stocks of Prime Western were built up and High-Grade remained tight. The Prince The Prime Western stocks are expected to be cut down and the demand for High-Grade more easily filled as the Depue reflux plant of the New Jersery Zinc Co. increases - production. Subistition of steel for brass in artillery shell cases will have a considerable effect on the zinc situation of the country one estimate of the saving in zinc in 1943 by this substitution being a little under 100,000 ton, of metal. The metal saved will, of course be High-Grade. If the substitution occurs, the present tight situation in High-Grade may be entirely relieved as new production comes on the market and zinc may find itself approaching a situation as comfortable as that of lead provided the supply of zinc-hearing raw materials is sufficient to keep all reduction plants tip to capacity production. The premium price of the per pound of zinc over set quotas which went into effect early in 1942, helped to bring about the new lead-slag-fuming plant and other new sources of raw materials.

Jan 1, 1943

By Harry C. Wiess

RECENT announcement of further restrictions on gasoline consumption in the Mid-West and Southwest has focused public attention on current discussions of an oil scarcity. Conflicting arguments are advanced on the one hand that we have plenty of oil and will not need to restrict consumption as soon as transportation facilities are adequate, and on the other hand that a great impending shortage will require most drastic reductions in civilian consumption in order to provide adequate supplies for military purposes. Data can be presented to support both views, the result being that the public is confused and uncertain of where the truth lies. For a nation with about half of the known crude-oil reserves of the world and two thirds of the total production it seems almost incredible to the layman that any shortage can exist. Those familiar with estimates of future demand. however. show increasing concern regarding our ability to meet military demands without further restrictions in civilian use or wasteful production from our remaining reserves. Only by considering such facts as are available and can be made public can a true appraisal be made of whether or not we are faced with a shortage that will amount to a crisis in crude oil.

Jan 1, 1943

By AIME AIME

C. H. BENEDICT, chief metallurgist of the Calumet and Hecla Consolidated Copper Co., has pioneered for nearly half a century. Noted for his ammonia leaching process, lie has Iong been responsible for all Calumet and Hecla mill, concentrator, and reclaination plant flowsheets. His influence has spread far beyond his own organization. lie is dean of Lake Superior metallurgists and has contributed greatly toward raising his specialty-the country over-to an honored profession; not merely an honored profession but a profitable one for industry and the public. The leaching process which he developed in 1912 has, since 1915, produced for Calumet and Hecla 250,000 tons of copper from waste tailings at a cost per pound, in 1929, below five cents. It has yielded profits of $35,000,000. In the war just ended, this process proved the only one adaptable to the recovery of copper from gilding-metal¬clad steel strip, and Calumet and Hecla treated more than 50,000 tons of such scrap for the Government.

Jan 1, 1945

By Blandford C. Burgess

Mica is an orchid among minerals. It is formed in pegmatites, one of the most bizarre of igneous formations, and is exceeded by few other minerals in the perfection it may attain as to size, color, and cleavage. First used for window glazing, as an ornament and article of trade, it has become one of the most essential insulators of electricity, heat, and shock. Most internal combustion engines use mica condensers or capacitors and such machines of war as planes, tanks, and submarines are immobile without it. The original manuscript of this guide was written in April 1943 at the peak of war emergency. It was not used be- cause shortly thereafter a decision was made to buy on a one price basis eliminating differentials for both quality and size. This is now presented with the thought that from the standpoint of preparedness we can only consider an- other war imminent and every effort should he made to set up in usable form the experience gained during the Second World War. Colonial Mica Corp. was set up by Metals Reserve Co. as a wholly owned government agency to encourage production of domestic mica and to purchase it. It soon became the exclusive buying agency for such mica. The writer as Southern Manager called on all the private agencies buying mica to assist in formulating buying policies, methods, and prices.

Jan 1, 1949

By F. L. Sizer

The mining regulations of British Columbia and Mexico present some features which might well be copied in the United States, if we are to have a complete revision of the laws governing mining titles. 1. First and foremost is the "squarc" location, which would mean the abolition of extralateral rights. This is a condition in both of the countries above named which has seemed to work no hardship upon any one, and certainly the limitation of underground rights by vertical planes through all lines makes a locator&apos;s rights clear. In view of the long and costly litigation which has involved so seriously many of our most important mining districts, it would seem to be the part of wisdom to avoid a repetition of similar trouble on titles of lode mining claims, by the enactment&apos; of a law similar to that in force in British Columbia. Objections have been raised by .representatives of English companies to the investment of large amounts of money in mining operations in the United States, because of the insecurity of title under the &apos;present apex law; and the statement has been made to me personally by one of the largest English operators, that he would .never again consent to the purchase of mines in the United States, preferring Mexico with all its revolutionary troubles to the danger of encroachment upon his underground rights by an unscrupulous neighbor. Without going into further argument as to the desirability of the I(square location," it should be sufficient to say to those who are inclined to "let well enough alone" and still stick to the "law of the apex" that there have never been any serious objections raised to this feature of the square location in either British Columbia or Mexico. There are well founded and logical reasons for abandoning the doctrine of extra-lateral rights since it is so difficult of interpretation; the most natural substitute being a law similar to that of British Columbia, giving to each locator an area 1,500 ft. square. I would advocate the right to locate adjoining claims of equal extent on either side of the discovery claim, on the strike of the lode, subject to a seasonable requirement in the matter of work upon them; and in the case of a vein dipping flatter than 45&apos; from the horizon, or in case of a

Jan 1, 1915

By D. F. Hewett

CONTENTS PAGE Introduction 1 Geologic features of eastern Oregon 2 Geology of the Sumpter quadrangle 2 Rocks older than the ore deposits 3 Rocks younger than the ore deposits 8 Lodes of the Sumpter quadrangle 8 Areal distribution 8 Geologic distribution 9 Major features of the veins 9 Mineralogy and texture of the veins 13 Ore deposits zonally disposed around the Bald Mountain batholith . . . . 13 Summary of mineralogy and texture 32 Zonal relations 33 Ore deposits zonally disposed around Greenhorn Mountain batholith . . . 36 Zonal relations 37 Relation of textural features to zonal arrangement of veins 37 Summary of zonal relations 38 Comparison with similar districts 39 Outlook for the district 40 INTRODUCTION IN an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931