Search Documents

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By Richard T. Ely

Conservation, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods whereby the natural inheritance of the human race may be improved; and still more broadly considered—and as used in popular discussion—it includes a treatment of the effects of productive conservation measures upon distribution. We shall give our attention briefly to the main points in this informal definition before we pass on to the thesis that conservation is largely a matter of property relations—-that a wise conservation policy means wise property relations.

Jan 1, 1916

By George Enos

As the coating formed affects the corrosion rate, duplicate samples of eight non-ferrous alloys were placed in flowing mine water. The alloys tested were as-cast or as-rolled and machined or polished. The paper describes the tests and gives the corrosion losses and the appearance of the samples at the end of the test. AN IMPORTANT factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the, terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2 mm. (equivalent focal length) apochromatic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002-0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002-0.0004 mm. thick. This thickness is equivalent to 200,000-

Jan 7, 1924

By W. W. Coffeen, K. E. Doud

A singular mineral extraction and processing operation is conducted by Metal & Thermit Corp. in Hanover County, Va. The mine presently produces aplite rock, rutile and ilmenite. The deposit lies in the piedmont plain about 25 miles northwest of Richmond. It first drew attention as a result of discovery of float rutile on the surface about 1910. About seven years prior to this, Metal & Thermit through a subsidiary. American Rutile Co., had begun producing rutile'and ilmenite from a deposit in Nebon County, near Piney River, where aplite rock and ilmenite are mined today. Because of the interest in titanium minerals and the similarity of the new deposit to the Nelson County deposit, Metal & Thermit became interested and eventually acquired the Hanover County deposit.

Jan 10, 1962

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983

By C. G. Dunn

MANY investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal orientation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the, complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.1-3 Furthermore, it is believe that high-stress regions exist in the vicinity of these bands4a and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallization.5,6 Similar evidence has been published for nonferrous metals.5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins existed prior to recrystallization.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary orientation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha irons Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing. three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involve more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By J. F. Wolff

EXPLORATION of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the im-portance that may be attached to certain characteris-tic strata in different formations. The following instructions for the care of core samples are issued by the Oglebay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan: The driller shall be careful upon removing the core from the core-barrel to keep the core in exact order. Not only should the pieces of core be kept in exact relation to each other, but care should be used not to turn them end for end. Core should be placed in the core-box from left to right in each row. Each drill should be furnished with small, hinged cover core-boxes, and each drill should be well supplied with empty boxes. Core remaining at the drill when the drillers are not working should be locked up. The practice of picking sample pieces of core and carrying them away from the drill to be examined in better light, or shown to someone else, is unnecessary and prohibited. The reason for this is that these pieces are seldom returned to the core-boxes and valuable information or "markers" may be lost. If the inspector suspects that a critical point is reached in the drilling and he cannot determine at the drill, he should remove the entire core-box and see that the drill is immediately furnished with an empty core-box. It is customary to split the core longitudinally so that one-half may be ground to a pulp for analysis and the other half may be kept for future inspection. The core should be filed in permanent core-boxes, properly labelled, if the core is to be kept in exact order as taken from the core-barrel. Otherwise, it is often filed in tin boxes inn the way that sludge samples are filed. To obtain the average analysis, the core and cutting samples obtained in the same run are analyzed separately and the analyses are combined in the proper ratio.

Jan 9, 1922

The earliest reference to coal in Tennessee is that by Dr. Walker in 1750 (see p. 18) where he saw it near the present site of Middlesboro. The next reference found is in 1798 when Morse stated, "some of these mountains, particularly in the, Cumberland, or Great-Laurel Ridge, are the most stupendous piles in the United States. They abound in ginseng and coal."' There must have been many places where it was seen in that interval, but nearly as long a time elapsed before Morris, in 1834, said that "fine beds of stone-coal exist in both East and Middle Tennessee."2 In a description of the Dover Iron Works, on the left side of the Cumberland River, a few miles above Dover, in Stewart County, it was said that "80 hands were employed in digging and transporting stone coal" and that the "plant had been running at least since Oct. 2, 1834."3 While doubtless coal had been used locally, this is probably the first use of it commercially in the state. The consumption of stone coal was 4,000 tons per year. In this same geological report openings of coal are mentioned near Battle Creek, Marion County, and in Bledsoe and Rhea Counties, where it was being used locally by blacksmiths; some other places were being worked near the turnpike road from Kingston to the Crab-Orchard, the product being hauled three miles to the Tennessee River and loaded in barges; farther west in. White County several outcrops were found. In Fentress County, several pits had been opened, the coal being sent down the Obey and Cumberland Rivers, and openings were also seen in Morgan, Anderson, Roane, Warren, Hamilton and Franklin Counties. The writer had hoped to publish an account of the iron works in the state but was unable to obtain the necessary information. He was told by an old iron-master, Mr. E. Embree, that

Jan 1, 1942

By Charles Fettke

IN THE present day manufacture of glass nearly pure quartz sands are used almost exclusively as the source of the silica, which is the major constituent of all common varieties of glass. Ordinary soda-lime, such as bottle, common tableware, plate, and window glasses, contain from 65 to 75 per cent. of silica. OCCURRENCE Glass sands occur in nature either in the form of loose, unconsolidated sediments or in deposits in which the individual grains have been more or less thoroughly bound together by some cementing agent so as to form sandstones. While deposits of sand and sandstones occur both widely and abundantly distributed, deposits that are sufficiently free from other constituents than quartz grains, so that they can be employed in the manufacture of the better grades of glass, are, comparatively speaking, of rare occurrence. The major portion of the glass sand produced in the United States comes from sandstones. In order to be suitable for glass sand, they should be rather friable. The rock should break down readily along the cementing material between the grains and should not break across the grains rather than along the bond. Some of the sandstones used are so friable that only light shots of slow-burning dynamite are necessary to disintegrate them sufficiently for hydraulic mining, while others have to be passed through crushers in order to disintegrate the rock into its individual grains.

Jan 2, 1926

By Charles H. Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding- lane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By Benjamin Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of :different types of hammer drills to various mining, quarrying, and, excavating operations, that an indication of the economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not I been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the"' rock drills;" that the placing of small holes inclined upward, at angles steeper than 40° above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In' spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped, three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized.

Jan 2, 1915

By Harold M. Mooney

The most significant trends appear to be an increased use of electromagnetic and geochemical methods. The most promising instrumental developments are airborne electromagnetic equipment, a magnetometer based on nuclear resonance, and reflection seismic equipment operable to depths less than 100 ft. Work in progress may lead to a one-man magnetometer capable of high precision and continuous recording.

Jan 3, 1955

By R. W. Schenker

INTRODUCTION Environmental and occupational safety and health requirements often have a major impact on the design of comminution circuits, leading to increased capital and operating costs and reduced income. A project's capital cost can be increased by environmental permitting delays and the addition of dust collection equipment. Income can be reduced by lost production during unscheduled plant shutdowns for dust collection equipment maintenance. Dust collection equipment must be carefully selected and sized to minimize impact on the project. The equipment performance must comply with environmental regulations and allow working areas to comply with occupational safety and health regulations. Unnecessary overdesign could jeopardize the project's desirability from an economic standpoint. The equipment must be sufficiently reliable to avoid interference with production schedules. This chapter provides practical information on the selection and sizing of comminution circuit dust collection equipment that is consistent with the requirements stated above. It presents information on the reasons and general principles of dust collection; various types of dust collection equipment; and design criteria for ventilation hoods, duct systems, fabric filter dust collectors, and fans. An example discussing the selection and sizing of dust collection equipment for a simple comminution circuit is also presented. REASONS FOR DUST COLLECTION Dust collection equipment should be installed in comminution circuits for a variety of reasons, some of which are discussed below. These include compliance with government regulations, minimization of housekeeping requirements, product recovery, and improvement in public and employee relations. Compliance with Government Regulations Dust emissions from comminution circuits must comply with both air pollution control and occupational safety and health regulations. The regulations that may influence the selection of comminution circuits are discussed in more detail in Chapter 2. Air pollution control regulations limit the emission of dust, as well as visible emissions to the atmosphere and the concentration of dust in the ambient air. These regulations minimize the degradation of air quality and impact to other environmental considerations such as the health of the general public,

Jan 1, 1982

By T. C. Aude, J. D. Pitts

The operating experience to date with long distance iron concentrate slurry pipelines at Savage River, in Tasmania, Australia, and Peña Colorada, in Colima, Mex., is discussed. The three pipeline systems currently under construction in Central and South America are described with particular emphasis on the SAMARCO system in Brazil, which will be the world's largest upon completion. General considerations for the technical, environmental, and economic feasibility of the slurry pipeline approach to solids transport are discussed with reference to alternative modes of bulk transport. A case study for the Lake Superior Dist. is presented.

Jan 1, 1978

By R. K. Young

This paper describes a computer-based Data Acquisition System which provides efficient data logging and retrieval, control of on-line gas chromatographs, and instantaneous calculation of material and energy balances.

Jan 1, 1977

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By F. E. Bash

PREVIOUS to the war, this country depended on Europe for its supply of a number of alloys of great importance in the manufacture of electrical apparatus and equipment. When this source was cut off shortly after the beginning of hostilities and the small stocks in the United States were exhausted, either inferior substitutes had to be used or the manufacture of the apparatus suspended. Since electrical equipment was of primary importance in the prosecution of the war, the substitutes had to be used until the composition and processes of manufacture of the alloys could be determined. Included among these alloys was one generally known as manganin, which is composed chiefly of copper and manganese and which, beside having a low-temperature coefficient of resistance, has a low thermal electromotive force against copper. These qualities make it valuable for the manufacture of electrical instruments and machines in which it is used in the shape of wire, rod, and strip. As a result of these circumstances, an investigation was started to deter mine how manganin could be made on a commercial basis so that a product of uniform quality and the necessary electrical characteristics could be produced. The object was to procure an alloy with temperature coefficient of resistance not greater than T 1 X 10-5 per ° C. and a thermal e.m.f. against copper no greater than that of the imported material. It is characteristic of manganin that the temperature-resistance curve is not a straight line but has a peak, which varies in position with different samples; it is most desirable, however, to have it at a temperature of 25° C. if possible. The coefficients of manganin from all records available ranged from a large negative to a large positive value. The composition as reported by different authorities is given in Table 1. Prof. Matthew A. Hunter, of Rensselaer Polytechnic Institute, made up a number of small melts of manganin in a graphite crucible and the one that he reported as having the best coefficient gave the following analysis: Copper, 83.6 per cent.; nickel 2.5 per cent.; manganese,-13.6 per cent.; iron, 0.3 per cent. An analysis of a sample of German manganin gave the following: Copper, 82.6 per cent.; nickel, 3.8 per cent.; manganese, 12.8 per cent.; iron 0.7 per cent.

Jan 9, 1919

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and outlining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods. In 1950 W. H. Westphal and the present writer developed a variation of this method and the apparatus for carrying it out. Their ideas were also based on experience with the Boliden Mining Co. method, which uses a small source coil and a vac- uum tube oscillator. The new procedure uses a small vertical source coil, powered by a vacuum tube oscillator, apd a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station only the inclination of the magnetic field created by the source is measured. Source Unit: The source coil and a small vacuum tube oscillator together weigh about 45 lb. The source coil consists of about 60 turns of 10-gage

Jan 1, 1958

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926