Search Documents

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By H. W. Graham

AS these annual occasions in honor of Henry Marion Howe continue through the years: there is progressively less likelihood that the lecturer will have had personal knowledge of Dr. Howe. The present speaker is one of those who unfortunately had no opportunity to come under the inspiring presence of this great metallurgist. A review of Howe's work shows it to cover a comprehensive range of interests and to evidence an impressive richness of detail. Not only was Howe at home in the laboratory, but he was familiar with the processes of iron and steel making and had a real understanding of them. His writings include much that is descriptive of processes with a wealth of material that is becoming of increasing historical value. He recorded his studies of the theoretical aspects of processes and published at least two process classifications, one in 1890 that was lengthy and somewhat theoretical, and a second in 1906 that was more of a practical listing. Wide as Howe's field of interest was, it is significant of the circumstances of his time that he gave- little consideration to raw materials or to their effect on iron and steel making processes. In 1933, Waterhouse, Howe lecturer for that year, presented a descriptive summary of the major steel making processes, and in 1946 Joseph discussed the blast furnace process. Otherwise Howe lectures have not dealt with processes as major subjects. In today's lecture, with no effort to describe the mechanical arrangements of iron and steel making facilities, it is proposed to examine the essential technological elements of the processes, to explore the inter-relation of these elements, and particularly to seek recognition and understanding of those factors which determine why certain processes are or are not used. The discussion of this lecture will deal with the major well-known large tonnage processes, with only such attention to processes of minor tonnage and special character as may be warranted for explanation by contrast. Subject to the errors of generalization and the shortcomings of condensation involved in presentation limited to a single hour, it is proposed to examine broadly but intensively those operations which convert raw materials into steel. It is an innovation for a Howe lecturer to discuss the raw materials of the iron and steel industry, but the changing circumstances of passing years intensify the influence of raw materials on processes and require the metallurgist to be alert for the process adjustments that may become advisable or mandatory. For a half century the metallurgical processing of iron and steel has followed a surprisingly straight path, but this does not necessarily mean that there are no curves in the road ahead. Ages ago primitive man came to know iron in its metallic form, not only by the

Jan 1, 1948

By H. W. Graham

AS these annual occasions in honor of Henry Marion Howe continue through the years: there is progressively less likelihood that the lecturer will have had personal knowledge of Dr. Howe. The present speaker is one of those who unfortunately had no opportunity to come under the inspiring presence of this great metallurgist. A review of Howe's work shows it to cover a comprehensive range of interests and to evidence an impressive richness of detail. Not only was Howe at home in the laboratory, but he was familiar with the processes of iron and steel making and had a real understanding of them. His writings include much that is descriptive of processes with a wealth of material that is becoming of increasing historical value. He recorded his studies of the theoretical aspects of processes and published at least two process classifications, one in 1890 that was lengthy and somewhat theoretical, and a second in 1906 that was more of a practical listing. Wide as Howe's field of interest was, it is significant of the circumstances of his time that he gave- little consideration to raw materials or to their effect on iron and steel making processes. In 1933, Waterhouse, Howe lecturer for that year, presented a descriptive summary of the major steel making processes, and in 1946 Joseph discussed the blast furnace process. Otherwise Howe lectures have not dealt with processes as major subjects. In today's lecture, with no effort to describe the mechanical arrangements of iron and steel making facilities, it is proposed to examine the essential technological elements of the processes, to explore the inter-relation of these elements, and particularly to seek recognition and understanding of those factors which determine why certain processes are or are not used. The discussion of this lecture will deal with the major well-known large tonnage processes, with only such attention to processes of minor tonnage and special character as may be warranted for explanation by contrast. Subject to the errors of generalization and the shortcomings of condensation involved in presentation limited to a single hour, it is proposed to examine broadly but intensively those operations which convert raw materials into steel. It is an innovation for a Howe lecturer to discuss the raw materials of the iron and steel industry, but the changing circumstances of passing years intensify the influence of raw materials on processes and require the metallurgist to be alert for the process adjustments that may become advisable or mandatory. For a half century the metallurgical processing of iron and steel has followed a surprisingly straight path, but this does not necessarily mean that there are no curves in the road ahead. Ages ago primitive man came to know iron in its metallic form, not only by the

Jan 1, 1948

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,' Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer's suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, .as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By Reno H. Sales

The present-day application of geological knowledge to mine operations owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contemplated. And finally, out of this situation there developed the independent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1935

By Reno H. Sales

The present-day application of geological knowledge to mine operations owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contemplated. And finally, out of this situation there developed the independent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1935

By A. P. Boller

In the victories of peace as well as of war, the science of engineering has played a prominent, if, indeed, not the leading part. While it might be interesting, and food for profitable thought, to trace the development of engineering from early times in its bearings upon the social betterment of mankind, it will be sufficient on the present occasion to suggest a few thoughts that it is hoped will aid the unprofessional listener to an appreciative consideration of the subject-matter laid down for to-day's discussion, and possibly lead the professional brother to a higher conception of the profession to which he belongs. Since the advent of the railway era, it is difficult to grasp the sequence of historic events that have led to the wondrous derelopment of mechanical science, making possible the civilization that is our daily boast, and opening up a vista of future intellectual and moral advancement among the nations of the earth, 'before which the imagination becomes hopelessly lost. Even now, looking back over a period of only half a century, we often fail to realize the vast change in the relations of individuals and nations to each other., brought about by the results of those mechanical discoveries which, having made the whole world kin, exercise a resistless levelling influence that bears fruit politically in the spread of republican ideas, and morally in the elevation of the individual through the facilities given to the dissemination of Christian ideas and general intelligence. In this view, it seems almost like a work of supererogation for a body of representative men of one department of that science to which the whole world owe. so much, to meet here at the centre of our national life to plead not only for a practical recognition of the national importance of the work to which their lives are devoted, but also for national aid, on a scale beyond that of private effort, to the end that mechanical science may be carried to a higher plane than ever yet attained, each step on the way being of material benefit to every man, woman, and child in the community. Possibly this is strong language, but none too strong when we consider that the work for which we plead is one affecting not only vast scientific and commercial interests, but also human life, to a degree little ap

Jan 1, 1882

By W. N. Best

Crude oil attracted attention because of its excellence as a fuel for openhearth furnaoes; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hotair furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This mcans a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity BaumB. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230". F., Mexican crude oil at from 175" to 210" F., and Beaumont, Texas, oil at 142" F. Fuel oil vaporizes at 130" F. Scientific Installation Essential The burning of oil is an art based on science, and the "rule of thumb" should never be employed, especially in heating heavy crude oil. Thermometers should be used on both suction and supply pipes so that the fireman or smith will at all times know the temperature of the fuel. The indicators on such thermometers should be large enough to be readily seen by the operator, night or day. It is necessary to have an unvarying pressure of steam or air through the burner, to atomize the fuel. Also, the air used to support combustion should be delivered through a nozzle under the burner at a constant pressure. The oil pressure must not fluctuate; under no eircumstances should it vary more than 1 1b. The oil pump, which should be brass-lined, with the aid of the pulsometer and superheater, will insure a constant

Jan 1, 1916

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By William Hume-Rothery

I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By William Hume-Rothery

I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By Charles Macdonald

It may seem to be almost unnecessary to occupy the time of the Institute in further consideration of a question which has been so comprehensively treated in papers already on file in our own Transactions and in those of the American Society of Civil Engineers. Unfortunately, however, the results of these concerted efforts have not been materially to increase our stock of Knowledge in the direction sought for; and as the necessity for this information is becoming.more and more apparent as the demand for structural materials increases, it is believed that by continuing the agitation by means of discussions in this and kindred societies, whose members are vitally interested in obtaining reliable data as to the properties of the materials they are called upon to work with, public opinion may be educated up to the importance of exerting such an influence upon the law-makers of the country as will result in the formation of a competent board, with adequate means at its disposal, to carry out this great work in a manner alike acceptable to the makers and users of the materials in question. It may be proper in the first place to glance briefly at what has been attempted thus hr, then to indicate some of the more important lines of needed investigation, and finally to consider reasons why government aid may with propriety be sought for in carrying on the work. At a convention of the Society of Civil Engineers held at Chicago June 5th, 1872, it was, on motion of General William Sooy Smith, resolved, that, " Whereas, American engineers are now mainly dependent upon formula for the calculation of strength of the different form of iron and steel, not based on experiments upon American materials and manufacture; and " Whereas, There differ greatly in many of their ch~racteristics front thoae of foreign production, both in their nature and forma: therefore,

Jan 1, 1882