Search Documents

By A N. Parry

In May 2018 Kasbah Resources Limited (“Kasbah”) completed an ore sorting test work program which was a precursor to releasing in July 2018 an updated Definitive Feasibility Study (“DFS”) for the Achmmach Tin Project in Morocco, which it is proposing to develop along with its joint venture partners. The testwork program evaluated ore sorting as a pre-concentration option to achieve early elimination of gangue and the low-grade component of ROM feed, thereby potentially:  Significantly upgrading the head grade of tin to the downstream processing plant.  Significantly reducing the required throughput capacity (and projected capital expenditure) of the downstream processing plant.  Reducing total consumables, power and water requirements in downstream processing.  Increasing the recovery of tin in the gravity and flotation circuit due to the higher feed grade achievable with ore sorting.  Reducing tailings tonnage, tailings cost and environmental footprint.  Using sorter rejects for mine backfill or road base applications. Key aspects of the design of the metallurgical testwork program centred around the need to ensure that samples representative of ROM ore feed (including projected mining dilution) were selected for the ore sorting testwork. The design and implementation of the ore sorting bulk testwork program is described, as well as a summary of the test work results and a discussion of the enhancement of the project economics reported by Kasbah, which led the company to adopt ore sorting as part of the proposed processing circuit in the updated 2018 DFS.

Nov 10, 2020

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

It would be a good thing when reviewing the challenges to be faced by the Australian gold industry to set the backdrop and scene for them, by briefly examining the history of this vital and dynamic industry in the Australian context. Gold mining in Australia had its official beginnings in 1851 when John Lister and William Tom discovered gold at YorkyÆs Corner, later renamed Ophir by Edward Hargraves. From that first tentative beginning, the ensuing rush of prospectors into New South Wales and Victoria meant that the annual gold production in those early years surpassed that of the next 40 years. This early rate of production was only eclipsed when AustraliaÆs production was once again lifted by the discovery of gold on the other side of the continent, in Western Australia. (Figure 1). The years leading up to the First World War saw Australian production peaking once again at over 115 tonnes of gold, a production rate that would not be surpassed until 1988. This renaissance in production at the beginning of the 1980s was achieved by the application of technology. The advent of bigger trucks and shovels meant that earth-moving costs dropped dramatically. This, coupled with the highly effective and efficient carbon-in-pulp processing route, stimulated the Australian gold mining industry into a state of frenetic activity. These two innovations were the principal factors that enabled the economic exploitation of the lower grade haloes left by the æold-timersÆ around the deposits exploited at the beginning of the last century-no high finding costs here. AustraliaÆs production through the 1980s and the early part of the 1990s was largely supported by the exploitation of these haloes. As these were depleted, the aggressive exploration effort stimulated by the strong cashflows of these early oxide deposits resulted in new æblindÆ discoveries which are now emerging as the backbone of the Australian industry (Figure 2). Gold production is a major contributor to the Australian economy. In 1998/99 the Australian gold industry accounted for approximately 16 per cent of the value of all mineral exports, which in turn accounted for over 35 per cent of AustraliaÆs total exports. As such, the Australian gold industry, by itself, accounts for just under six per cent of AustraliaÆs total exports (Figure 3). Consequently, the industry is responsible for over one per cent of AustraliaÆs gross domestic product. These statistics are all the more compelling when we consider that, at the beginning of the 1980s, goldÆs contribution to exports and GDP was insignificant (Figure 4). Within the Australian resources industry, gold mines and associated infrastructure account for ten per cent of all capital expenditure (Figure 5). From an employment point of view, in 1997/1998 the industry directly employed (excluding contractors) about 7700 people, approximately 15 per cent of all those employed in the minerals industry. Just under nine per cent of the workforce in the minerals industry are female, whereas in the gold industry over 16 per cent are female.

Jan 1, 2000

The problem of comparison of island arc's andesites in terms of petrochemical data is exa- mined. It is definitely established that only two main factors exist controlling the petroche- mical variety of the Kurile arc's andesites.Ori final multivariate statistical technique and computer software are used to extract these fac- tors. It is shown as well that the chemical com- position of igneous rocks depends on the type and structure of the Earth's crust. The follo- ~cing interpretation is proposed for the two factors describing petrochemistry of andesites: the first one is the depth to the Benioff seis- mofocal zone and the second one is supposed to indicate the position of the peripheral magma chambers. The basic trends of variations in the chemical composition components depending on the changes in the controlling factors are de- Tcnnined.

Jan 1, 1987

The annual growth in lead consumption in the Western world has declined sharply in the past ten years, as lead has suffered a wave of substitution by other materials, and has also been the object of concern about its toxicity in daily applications. Like most metal industries, the lead industry has tended to be more production-oriented than market-oriented than is the case with some of its competitors. However, in recent times this pessimism and preoccupation with weathering the threats from environmental legislation, substitution and low prices appears to have been replaced with a new optimism in some sectors of the industry. This is indicated by renewed promotional activities and efforts to find more applications and market opportunities.

Jan 1, 1985

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

Byproduct coking is practised in three of the major Australian ironmaking centres, the Newcastle and Whyalla works of the Broken Hill Proprietary Co. Ltd. and the Port Kembla works of Australian Iron & Steel Pty. Ltd. Coking first commenced at Newcastle in 1915 and at Port Kembla in 1938. The installations established at these centres include coal cleaning facilities and com- plete byproduct streams. The Whyalla plant, because of its location is somewhat less extensive, having no coal cleaning plant and a comparatively restricted byproduct section. As new batteries have been built every opportunity has been taken to incorporate modern design features and improved operat- ing techniques. This has included the provision of equipment to reduce atmospheric and water pollution. A marked reduction of markets for byproducts has had serious repercussions on the profitability of this section of the Industry.

Jan 1, 1972

By J Bang, I-H Jung

Ti is an important constituent for steels and superalloys. During the continuous casting process and ElectroSlag Remelting process (ESR), Ti in molten steel and superalloy can have chemical reactions with casting flux and ESR slag containing CaO and CaF2. In order to investigate such exchange reactions, the understanding of the (Ca,Ti//O,F) reciprocal slag system is prerequisite. In the present study, a coupled phase diagram experiment and thermodynamic modelling of the (Ca,Ti//O,F) reciprocal system was performed. In particular, the phase diagram of the CaF2-TiO2 system was experimentally investigated by Differential Thermal Analysis (DTA) experiment and quenching experiments followed by Electron Probe MicroAnalysis (EPMA) phase analysis. The Gibbs energy functions of all solid and liquid phases in the (Ca,Ti//O,F) reciprocal system were optimised to reproduce the present data and all available reliable experimental data in literature.

Jun 19, 2024

By Allchurch P. D

At Perseverance a reserve of 45 million tonnes at 2% Ni was indicated by drilling. Holes were drilled in trellis pattern on section lines 61m apart to assess shallow mineralization. To explore at depth holes were spaced 122m apart, collared vertically, then allowed to deflect under controlled drilling conditions. The mineralization may be divided into the three homogeneous classes of soarsely disseminated, heavily dissem- inated and massive sulphides. In the standardised sampling and assaying procedures used to assess the deposit, attention was always paid to these fundamental ore types. All sampling and assaying processes were continuously monitored by checks. Sampling and sample preparation errors were small, to judge from the differences between results of original and check samples. Assaying errors, determined from analyses made by independent laboratories using different methods, slightly exceeded sampling errors. Comparison of underground core, c'iannel, and grab sampling, suggests that core sampling tends to undervalue.

Jan 1, 1976

By Canning RL, Pritchard J

The surface treatment works in the Mount Isa Mines Limited copper stream consist of a concentrator and smelter with annual capacities of 5.6 million tonnes of ore and production of 155 000 tonnes of anode copper respectively. Both plants have been sites for process optimisation in recent years, the emphasis being to achieve productivity gains in each particular plant. The continued low real world prices for copper resulted in an in-depth review of the entire copper process stream. This indicated the need for developments within both the concentrator and smelter, and changes to operating strategy to ensure that the entire treatment stream could be optimised. The paper reviews these changes.

Jan 1, 1986

By Riley S. J

The basic aim of mine planning is to design mine layouts and schedules that achieve optimisation of operations, minimum cost and maximum resource recovery. Successful accomplishment of this aim is facilitated by timely and comprehensive rehabilitation planning commencing at the pre-feasibility stage and continuing until the end of mining. Incorporation of a final landfomt design for waste rock dumps in a mine plan requires a prediction of surface stability, which may be achieved through erosion modelling. Erosion prediction models can be placed in two broad categories: soil loss prediction models eg USLE and CREAMS, and geomorphic models such as SIBERIA. A waste rock dump landform design based on selected slope form and grade and drainage systems should be developed as part of planning. A digital terrain model (DTM) of the landfonn should then be produced which can be modelled for long-term erosional stability using pre-determined parameter values. If acceptable standards of stability are not achieved, the landform should be redesigned and remodelled until the desired result is obtained. The planning process incorporating models requires knowledge of spoil or waste rock properties and model parameter values. This information is site specific and can be obtained from drill cores or costeans at the pre-mining stage and from spoil or waste rock during the mining stage. Realistic model parameter values are critical in post-mining landfonn design and can be obtained by several methods, including rainfall simulation, monitoring, geochemical analyses and grain size analysis.

Jan 1, 1994

By A Dal-Corobbo

Traditional acid and metalliferous drainage (AMD) wastewater treatment focuses on the iron co-precipitation/adsorption process as this is a very effective method of reducing heavy metals, including copper, lead, zinc, arsenic, etc, to parts per billion (ppb) levels in AMD wastewater streams. One of the drawbacks to this method however is the large volume of sludge produced and subsequent disposal costs for the mine site concerned.A proprietary metals treatment system called high density sludge (denoted HDS) which significantly reduces the quantity of waste generated is described in this paper. This process generates a dewatered sludge that contains in the order of 50 to 55 per cent solids. This sludge is denser than conventionally dewatered sludge, which typically contains only 20 to 30 per cent solids. This advanced process has a wide range of applications and can be easily retrofitted into existing AMD treatment systems. It has been successfully installed at several mine sites to treat AMD wastewaters. This paper discusses the high density sludge process, its benefits and provides data and operating results from pilot test installations.CITATION:Dal-Corobbo, A, 2013. High-density sludge process for treating metal bearing acid and metalliferous drainage wastewaters, in Proceedings Water in Mining 2013 , pp 217-220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The proponents of new mining projects always run the risk that their project is deemed to be not in the public interest. Nothing to be done here except to try and pick it earlyùit is, after all, the approvals process that is supposed to screen such projects out. But there is a second risk, about which much can be done: that inadequate or untimely information confuses the formal assessment of a project and the political context within which the decision is ultimately made. This is environmental impact assessment (EIA) process risk and it has become steadily greater in a changing world, where: miners have lost clout; public trust in institutions has declined; governments follow, as authority pyramids give way to spheres of influence; NGOs are asking the questions people want answered; and stakeholders have become the reference point. This new world deals harshly with yesterdayÆs methods. But it needs to be understood if principles and methods for managing EIA Process Risk are to be advanced.

Jan 1, 2003

By M N. Ingham

X-ray fluorescence (XRF) spectrometry has always been considered to be a comparative method of analysis. Reference materials are required to calibrate the analytical system. This paper describes the use of a set of æsyntheticÆ oxide standards, made from commercially available high purity compounds, to calibrate a spectrometer for 21 major and minor oxides. The spectrometer software uses simple methods of background correction, and a fundamental parameter method of matrix correction. Sample preparation is by fusion in 66 per cent lithium tetraborate, 34 per cent lithium metaborate. The use of synthetic standards, made from traceable compounds, brings XRF significantly closer to being a primary rather than a comparative method. Reference materials were used to validate the method described and examples of accuracy for major constituents are given using ores and other minerals. This method has successfully been used to analyse a wide variety of minerals and ores, as validation data shows. A titanium process example clearly shows the benefits of highest accuracy analysis.

Jan 1, 2008

By Thomas W

Due to record low tin prices and an uncompetitive position in world markets, the Renison tin mine has undergone three major phases of restructuring in the last three years. This has involved substantial job losses, almost all of which have been through voluntary retrenchments. Retrenchments took place in 1988, 1990 and 1991.The last phase of restructuring was the most dramatic, as many aspects of the operation of the mine were changed. New pay structures were introduced, and the miners' contract system was scrapped. Drastic pay cuts occurred in many areas, although the opportunity was also taken to increase pay at some of the lower levels where inequities existed. Work practices were changed, as was the management structure.

Jan 1, 1992

By S Pigram, G J. Jameson

This paper is concerned with the tracking of particles in the froth phase of an aerated water/glycerol mixture. Experiments have been carried out in a specially designed laboratory flotation cell that allows formation of a deep froth. Phosphorescent tracer particles of various sizes were injected into the centre of a froth column where they were excited by ultraviolet lights, positioned at the back and front of the column. The motion of particles was captured on a digital camera with a green filter. The images from the digital camera were then transferred to a computer and an image analysis program was used to convert the colour intensity to the concentration of particles at each location within the froth. The tracer technique was used to determine the dispersion of hydrophilic particles and the variation of the concentration of solids with axial and radial positions.

Jan 1, 2005

By Lawson E, Purkiss S. A R, Van Ashwegen p C

It is only in the past decade or so that industrial exploitation of biological resources and techniques has become regarded as a distinct discipline. Commonly referred to as Biotechnology, it embraces biochemistry, microbiology and the engineering sciences and is mainly aimed at the biological conversion of suitable raw materials into desired end products. The catalytic agents are more often than not bacteria although other micro-organisms such as fungi are used. The range of micro-organisms used is wide and the choice depends upon the desired end product, which in turn depends upon the metabolic attributes, genetically engineered or otherwise, of the cells. The metabolic diversity of micro-organisms has been applied to processes such as antibiotic production, food processing, brewing and chemical production, and of course extraction of metals from ores. Metabolic diversity is, to a certain extent, based on nutrition, which, in its simplest form, can be divided into energy source, carbon requirements and nature of the electron donor producing reducing power to the cells. The source of energy may be light, in which case the organisms are phototrophic (eg green plants, algae). The carbon requirements and reducing power may come from organic sources. These organisms are then called heterotrophic (eg man and most bacteria, including the well known Escherichia colt). However, there is a group of bacteria whose energy metabolism depends upon chemical redox reactions, use inorganic carbon (CO2) and obtain their reducing power from reduced chemicals such as metal sulphides. These are known as chemolithotrophs. They play an important role in mineral recycling in nature and are also ideal for extraction of metals from ores. This is because they are extremeophiles being acidophilic (grow at very low pH) and sometimes also thermophilic (grow at very high temperatures). These bacteria operate in such hostile environments that competition, or contamination, by other organisms does not occur. Extraction of metals from ores by chemolithotrophic bacteria is commonly referred to as biohydrometallurgy. Other related areas are bioadsorption of metals from dilute solution,- microbial treatment of metal contaminated wastes and removal of toxic chemicals produced or used during mineral processing. This paper basically reviews the work that Gencor has undertaken in the field of biohydrometallurgy and the advancements it has made in commercialising the technology, but also touches on certain long-term areas of research that are currently under investigation.

Jan 1, 1995

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By T Laing, M A. Abdalla, P Hagan

Open pit operators are facing a number of challenges in the area of blasting and blasting processes, such as wall control, quality of fragmentation, explosives consumption and vibration. Remaining financially viable is one of the most significant objectives for mining professionals as they work through the blasting challenges within the mining chain of processes. This objective is such a significant challenge, primarily due to the high consumption of materials and the direct consequences on the downstream processes in the mining work flow, including loading, hauling, crushing, milling and mineral concentration. This paper reviews and discusses a technique to achieve this objective, namely air-decking. The performance in a number of mines around the world is reviewed focusing on the economic contributions of air-deck blasting. Various scenarios are investigated and simulated, covering both conventional and air-deck blasting, using JKSimblast software. The scenarios explore a range of issues and found that optimum results could be achieved with a minimum amount of explosives. The results obtained from the simulations were verified with blasts at Rixs Creek Coal Mine, Australia. Based on the verification results the simulations were then modified to more accurately model the actual conditions and parameters on site and to ensure that the models derived meet the production and control requirements at the mine site. Ultimately, overall analysis and comparisons were applied to the outcomes of the conventional and air-decking blasts revealing a reduction in material consumption of around 25 per cent with consequential savings and up to a 30 per cent reduction in ground vibration.CITATION:Abdalla, M A, Laing, T and Hagan, P, 2012. The contribution of air-deck blasting to open pit mining economics, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 7-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Pak DL

Over the last decade computers have become an essential element in assessing the economic feasibility of mining new mineral deposits and in assisting a variety of related support functions. A broad overview is given of the many technical application areas where computers are contributing to the mining industry with reference to work being done on the evaluation of drill hole information, mineral inventory modelling, ore reserve estimation, financial analysis, process simulation, process control, workshop job scheduling, PERT applications, and com- puter aided drafting. In all these areas the computer has greatly reduced the manual effort involved in looking at alternatives. It has had a significant effect in eliminating delays in revising calculations, or rescheduling activities to incorporate new data or cater for changing conditions, while at the same time providing more accurate and prompt information for the management decision making Process.

Jan 1, 1980