Search Documents

By Lin Bin, Qain Minggao, Qu Qundi, Yao Zhichang

This paper describes the application of a 89C52 chip microcomputer in hydraulic pressure information monitoring system of powered supports in a coal face, and the details of circuit and software of a monitoring system substation. Each substati

Jan 1, 1998

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity.Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer.

Jan 1, 1990

The screening of iron ores, sinter and coke, and investigations undertaken to improve screening efficiency and cloth life are discussed. The major modifications to coke screening proposed with the construction of No. 7 coke ovens battery are briefly described. The major problem areas were identified as screen cloth blinding and pegging, feed presentation and screen overloading. Blinding and pegging have had a significant effect upon screening efficiency with the screening of sinter, coke breeze and wet iron ores in particular. Pegging can be reduced or eliminated by the correct selection of aperture size and shape, screen excitation and slope, and screening medium. Blinding encountered with wet coke breeze was a particular problem in which no significant progress was made.

Jan 1, 1984

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

The Hall-Hoult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-H6roult cell - the electrolyte, the anode and the cathode - are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride - carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.The construction and testing of a full-size "Low Energy Cell" is scheduled for early 1986 and is expected to reduce energy consumption in aluminium production by about 15%.

Jan 1, 1985

Open pit mines in the Yilgam Craton have unique hydrogeological characteristics resulting from a combination of geology, mineralisation and the complex and extended development of the regolith. The principal features of this geological relationship are:ò deep and complex multi-stage development of the weathering profile; ò steeply dipping rock layering;ò supergene enrichment; andò mining across the regolith/rock interface.These features result in large changes in permeability horizontally across rock layers; vertically through the weathering profile and along-strike in association with mineralisation and the mineralised Structure.

Jan 1, 1993

Gold at Renco occurs in association with pyrite, pyrrhotite, chalcopyrite and quartz and is confined to a series of brittle fractures and fault breccias (reefs) preferentially developed within an anastomosing ductile shear zone. During late Archaean crustal movements both the orebody and the enclosing host rocks were deformed within a series of east-north-east striking, southerly dipping, shear zones. The reefs within these shear zones are now texturally different to those away from the shear zones, and this difference is reflected by differences in the way the gold is distributed in the two reef types. These differences are not taken irto account by the software package currently being used to generate kriged plans of gold grade and reef thickness and this may explain some of the inaccuracies found in these plans.

Jan 1, 1990

Discontinuities often have a very detrimental effect on the stability of mine highwall faces. The west wall of the Muja open cut is remarkable for the number and variety of discontinuity sets which occur over a relatively small area. To-date 14 separate structural domains have been identified over an area measuring approximately 560 m by 120 m.The structural domains have been grouped into four structural assemblages on the basis of their angular relationships to each other and to regional folding and faulting. The distribution of these structural assemblages appears to be erratic and no controlling factors have been identified to explain or predict them other than in the most generalised terms.

Jan 1, 1993

By Rabie A. S, Fouad K. M, Ammar A. A

The existence of Gabal El Kahfa ring complex, located in the Eastern Desert of Egypt, has been ascertained from aeromagnetic and aeroradiometric survey data as well as by aerial photography. Two maps for -the net aerial radiometric measurements reduced to ground level and aerial magnetic data corrected for the regional normal gradient of the earth's magnetic field have been constructed. The aeroradioactivity data have been interpreted geologically and analyzed statistically to outline various radiometric units and compute their charac- teristic statistics. The ring complex showed a circular radiometric feature and yielded a radiometric mean background and a standard deviation of 6.48 and 0.89 pR/h respectively. Besides, the observations showed a normal distribution. The aeromagnetic data have been reduced to the north magnetic pole, then filtered to produce the regional-and residual-component maps. Statistical trend analysis was conducted for the tectonic linea- ments resulting from the three magnetic maps, to define the structural framework of the area under study. This statistical study proved the exis- tence of trends in the east-west, northwest-south- east, northeast-southwest and north-south directions. The ring complex is characterized by a circular magnetic feature, whose average relief is 2150 nT. It is included within a high east-west trending magnetic zone. The latter represents a deep-seated uplift or anticline which is bordered from all sides by some faults of different trends.

Jan 1, 1988

An underground storage and filling distribution system is presently being established at North Broken Hill Limited in the No.3 Shaft area. This has been necessitat- ed by the dependence of the present filling system on the No.2 Shaft and its imminent closure due to cessation of production. The storage will consist of three tanks excavated in low grade ore, between the No.20 and No.21 levels, at approximately 2700 feet below the surface. The tanks will each have a capacity of 1500 cu yds. Consideration was given for surface storage, although under- ground storage was thought to have greater merits. Two tanks have been excavated, and are in operation. Three or more outlets are installed beneath each tank, with horizontal connections into the No.21 level 'mixing box'. Water decants from the top of the fill in the tanks, and passes into a decant water sump, at the bottom of which is a borehole to the No.21 level. This is then connected to the mixing box and water used as make-up water with the semiwet solids for transport into the existing pipe distribution system. Preliminary results of the system have been satisfactory and it is envisaged that this system will readily cope with the filling demands of the future.

Jan 1, 1973

By Hsiung SM, Jiang YM

The orientation and location of the hydraulic legs are two very important parameters for the design of shield supports in longwall mining. Studies have shown that leg orientations and locations of a support determine the magnitude, orientation and location of the resultant support resistance which in turn affects the efficiency of the support and the ability to prevent premature roof falls in the face area. Therefore, there is a need to determine the best combination of orientation and location of the hydraulic legs for each type of shield support under various geological conditions. This paper attempts to evaluate, first, the individual role of each parameter (orientation or location) and then to determine their integrating functions in terms of ground control employing finite element analysis. Three types of shield support (2-leg and 4-leg shields and 4-leg chock shield) with various combination of the parameters are simulated and their effects are discussed. The optimum design for each parameter for each support type under various geological conditions is also discussed and recommended.

Jan 1, 1988

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

The main aim of the conference is to work towards improved useage of steelplant slags which have largely been considered waste mater- ials, This paper summarised investigations carried out on the suitability of air cooled blast furnace slag, blast furnace granulated slag and basic oxygen steelmaking slag as road base materials. All slag samples were obtained from the PortòKembla Works of Australian-Iron and Steel Pty Ltd. Since road making materials are increas- ingly being characterised by use of resilient moduli, the compressive strengths and resilient moduli were determined for road base of the following slags. 1 Air cooled crushed blast furnace slag 2 mixes of air cooled blast furnace slag, granulated slag, and lime 3 mixes of air cooled blast furnace slag,-granulated slag and basic oxygen steelmaking slag. Evaluation of a local dacite (dense medium grained igneous rock, classification rhyolite), generally considered an excellent road base course material, was carried out for use as a reference material.

Jan 1, 1979

CONTENTSIntroduction.Ore Bodies.Variations in Ore Dressing Practices.Stage I .Gravity Concentration for the production of a Lead Concentrate. 1909-1918.Stage Il Gravity plus Flotation Treatment for the production of a Lead Concentrate and a Zinc Concentrate. 1918-1929.Stage III All Flotation Treatment for the production of a Lead C~mcentrate and a Zinc Concentrate. 1930-1939General Summary - Stages I, II, III.Stage IV Gravity plus Flotation Treatment for the Production of a Lead Concentrate and a Zinc Concentrate. 1939-1947.1. General.2. Notes on Ore Dressing Practice.A. Gravity Section - Re~oval of Free Galena.B. Secondary Ball Mill Grinding Section. .a. Mineral Association.b. Composite particle problem.c. Degree of grinding required.d. Free Gangue Minerals in Table Tailing.

Jan 1, 1948

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By Swain H. D, Kay R. L

Assessment of mineral reserves in any ore- body hinges on both mineralisation characteris- tics and the economics of extraction. The mineral reserves statement depends on interpre- tation of diamond drill information by geolo- gists, determination of the production plan and operating costs by mining and metallurgical engineers and prediction of future income by economists. The techniques used to generate the mineral reserves statement for Bougainville Copper Limited in 1969 are described and the accuracy of predictions discussed. Preliminary results from a geostatistical reassessment are comp- ared with the ore zone model, blast hole data and concentrator reconciled production results.

Jan 1, 1979

By Hermulheim W

In the Federal Republic of Germany hard coal is mined underground only. The coal mines reach down to 1 500 m deep, recently having an average depth of 900 m. The commonly used winning system is long- wall mining with face lengths up to 250 in. The gate roads, which separate the seam into single panels, have an average length of one kilometre with a cross- section up to 20 m2. These single entries are usually supported by yielding steel arches. The installation of steel arches can hardly be mechanized. The choice of heavier support, caused by increasing depth and roadway cross-section, results in high cost for labour and material in gate roads. Furthermore, the heavy steel arch is acci- dent-prone, not only during installation but also during transportation and ship- ment. Rock bolts combined with a suitable lagging offer a way of mechanizing support work in headings. The aim is to decrease cost and to increase mine safety and pro- ductivity. Over the last ten years, 50 km of gate roads have been reinforced by a combination of rock bolts and weld mesh. Nevertheless, there are still differing opinions on the feasibility of rock bolting in gate roads. In Germany a long tradition and experience with steel arch support exists, whereas the function of an anchorage is a closed book to miners, preventing this new technique from spreading more quickly. Advantages and shortcomings of both steel arch support and rock bolting are compared. The experience with rock bolting up to now is reported. Possible improve- monts arm discussed.

Jan 1, 1986

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

By Plumridge C. L, Lynch J. E, Forresty R. J

The Amanda Bel Goldfield (new name) is an area of approximately 1000 sq. km centred 65km WSW of Ingham and 150km due east of Kidston (Camel Creek homestead to Ryeburn homestead area). Gold mineralisation has been located in tightly folded sediments of the Silurian Greenvale Formation as well as in the Early Devonian Kangaroo Hills Formation and the Early Carboniferous Clarke River Formation. The area is traversed by a major NW-SE structural corridor, with many of the numerous basaltic, andesitic and rhyolitic dykes of the region sharing a similar trend. So far fourteen gold-bearing zones have been located, all of which are new discoveries delineated by bulk cyanide leach sampling and subsequent geological reconnaissance. The region has undergone three periods of deformation with gold mineralisation introduced syn-D1, post D1 - pre D , syn-D and post-D2/D , thereby revealing an involved metall~genic history. Mineralisation types include Sb, Sb-Au, Sb-Au-As, Sb-Au-As (-Pb-Zn) and Au-As. Minor occurrences of W, Pb-Zn-Ag and Pb-Zn-Ag-As-Sn are also present as are alluvial (deep lead) tin Drosoects.

Jan 1, 1989