Search Documents

By Fabjanczyk M. W

A limitation to present theoretical roof reinforcement design methods is the inability to derive accurate and quantitative information about the roof rock condition and the action of reinforcement at various excavation stages. To obtain the information required to assess roof rock stability, detailed monitoring of the in-situ behaviour of reinforcement and roof strata is required. Reliable instru- mentation and techniques have been developed for use in underground coal mines to identify the geometry and magnitude of displacements occurring in roof rock and the forces generated in reinforcement. The use of such instrumentation allows an accurate assessment of the in-situ capability of reinforcement and the mode of reinforcing action developed. In-situ monitoring can supply data required for the practical design of reinforce- ment and assess the potential stability of current designs. The use of such data together with mine wide appraisal of rock and stressfield considerations, can allow roof reinforcement to be designed on the basis of a predicted roof Response.

Jan 1, 1986

Authority to Prospect 57P lies within the Surat Basin',' an eastern lobe of the Great Artesian.Basin, a major Mesozoic . downwarp that,had its inception'in Triassic time. The northern edge of the Mesozoic Surat Basin overlaps the southern extension of the Bowen Basin, a 'major structure that warped do*nWard in varying degrees from Permian time into Early'Triassic time: The axis of the Bowen Basin may be superimposed on the axis'of a still older structure, the Tasman Geosyncline, that probably originated in Ordovician time culminating in Late Carboniferous time.Within. or bordering the area the geologic record 'clearly marks.major differences in the stratigraphy and structure related, to"the successive evolution of these three distinct structural units. Three major phases of sedimentation have been recognised; one related to the development of the Tasman Geosyncline froi'n. Devonian to.Early Permian time (Horton group), one related to-the development of the Bowen Basin from Early Permian to_Early Tri= assic time (Bowen group), and one related to the development of the Great Artesian Basin from Triassic to Cretaceous time (Great Artesian . Group).

Jan 1, 1962

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

By M Field

Kimberlite pipes, as opposed to dykes, sill and secondary deposits, are the primary target for diamond exploration companies because they have simple geometries and can contain large volumes of potentially diamond-bearing ore. Once discovered, important decisions have to be made regarding the sampling of these geological entities to establish the total volume of ore present, and to define the internal geology, which can be complex in nature and controls the distribution of diamond grade. It is essential that as part of this process the uncertainty in constructed geological models are assessed. In this paper the Orapa AK1 kimberlite pipe in Botswana is used as a case study to explore a potential methodology for defining this uncertainty. The uncertainty of the rock volumes of different types can be characterised by a geostatistical approach. Geostatistical simulations, based upon a plausible representation of the geological bodies, provide different possible images of the orebody that can be considered as different realities. By testing different borehole layouts and drilling the orebody virtually on the computer, many different, but equi-probable realisations of the pipes can be produced. It is then possible to estimate the rocksÆ volumes and compare them with the actual ones. A statistical analysis of the relationship between estimation error and the number of boreholes can then be used to optimise the next sampling campaign. The rock volumes are obtained from a two-step simulation process. Firstly, the pipe geometry is simulated by means of introducing variations around the geological block model, by an original method called centre point simulation (CPS), which has been developed for this purpose. Secondly, the internal geology is then simulated within the pipe. The methodology for simulating the internal geological zones has to be adapted to the level of information and to the geological structure itself. The upper portion at Orapa AK1 is filled with sedimentary crater facies. Here plurigaussian simulation techniques can be applied that are adapted to the simulation of sedimentary facies. The central zones of the pipe are typically subvertically-oriented massive volcaniclastic deposits and breccias and the lower regions comprise a complex root zone. CPS is appropriate for these zones.

Jan 1, 2006

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991

By J Coombes

The JORC Code lists the three core principles of Transparency, Materiality and Competency as fundamental to how mineral estimates are publicly reported. But where the principles of Transparency and Materiality can be considered conscious choices underlying decisions at the point of disclosure, Competency is a self-declared position statement based on one’s confidence to defend a technical position (as well as the functional pre-requisites of institute membership and a minimum of five years relevant experience).Developing competency in the mining industry is an ad hoc process, generally left to the individual to chart through a process of osmosis from personal work experiences that lead to a sufficient level of confidence. Companies that actually present professional development programs leading to reporting competency are rare. And even once a person has followed a program, there is no specific outline of what constitutes technical competence.No doubt, there are persons signing off on mineral statements who would benefit from developing and/or updating their technical skills (they may not even be aware of unmastered skills). Equally, there are technical practitioners who are sufficiently competent, but lack the confidence to step up and publicly report their estimates. Confidence in one’s own abilities plays a significant role in deciding when one is ready for the responsibility of submitting mineral estimates for public consumption. In addition, a person’s organisational support, such as the availability of suitable peers and professional development programs, and opportunities to learn from a variety of technical projects contribute to developing relevant experience. Increased exposure in both technical breadth and depth enhance confidence in one’s ability and competence.The mining industry provides numerous opportunities through direct and indirect means to develop the competency underpinning a stable reporting code. This paper examines a theoretical framework and associated processes that could be used to examine how the mining industry, companies and individuals collaborate to develop this vague principle of competency. This paper seeks to initiate research with the express purpose of enabling more effective and efficient development of reporting competency in our industry.

Aug 22, 2011

Investigation of standard tests used to establish the decrepitation rating of Western Australian iron ore showed scatter in results which could be reduced by textural type sampling. Testing of individual textural types resulted in separation.of a range of decrepitation behaviour patterns. No unique correlation was established between water content in goethite, or between any single mechanism and breakage in shock heating. The latter depends rather on several mechan- isms whose operation is controlled by the texture of the ore. Texture studies were used successfully to predict decrepitation behaviour which could be related to orebody structure for mine planning, and blending for sales or processing requirements.

Jan 1, 1973

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

By Ostrea AM

Aqueous oxidation in an autoclave at ele- vated temperatures and oxygen partial pres- sures is applied to Philippine gold-bearing sulfide ores and concentrates which respond poorly to conventional cyanidation. The gold concentrates are recovered from ores and tail- ings material using the patented OMLI Process (the OMLI Process is able to upgrade tailings material analyzing 0.50 g/t Au to a concen- trate with a grade of 5 g/t Au or better). The results show that with aqueous pre- oxidation of the concentrates ahead of cyani- dation a four-fold increase in gold recovery is obtained compared with straight cyanida- tion. The observed differences in response to the pre-treatment step between various mate- rials are correlated with their mineralogical composition. The chemistry of aqueous oxida- tion is also presented.

Jan 1, 1986

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

By Hebblewhite B, Humphreys D

An experimental mining project has been carried out in the Collie Basin to demonstrate the safe operation of total extraction mining techniques in the underground mines of the basin. To achieve this, it was necessary to design and install a means of controlling or removing groundwater so that goafing of the overlying strata could be safely achieved as part of the mining operation. The site chosen for the experiment was a triangular panel adjacent to Western No 6 (WD6) underground mine, which includes the 3 to 4 m thick Wyvern Seam beneath 130 to 180 m of overburden. The test area abuts a major fault on the downdip side. The overburden and underburden sequences include several horizons of permeable sandstones which form major aquifers. Water problems have long been recognized in all underground mines in the Collie Basin, and have previously prevented the successful application of total extraction mining. Following extensive hydrological investigations, dewatering and depressurization systems were designed to dewater the immediate roof aquifers and to depressurize aquifers higher in the sequence and in the floor. This would enable stable roof conditions to develop and controlled goafing to be achieved. The roof dewatering/depressurization procedure involved a combination of in-mine vertical roof drainage holes and conventional dewatering bores constructed from the ground surface above the mining trial area. The dewatering system was installed and operated for 29 months before the commencement of mining. Mining was eventually successfully completed in two trial panels using a retreat Wongawilli extraction system using bridge conveyors and continuous miners. Water inflow into the mine workings was channelled to a constructed sump area at the lowermost corner of the panel and pumped to the surface via vertical sump bores. The dewatering and depressurization measures adopted were successful in permitting the first controlled and systematic total extraction recovery of coal from the Collie Basin. This trial mining exercise demonstrated the potential for increasing substantially the recovery of coal from the Collie Basin, where previously recovery rates of around 30 percent from underground mining were commonplace, using only bord and pillar methods.

Jan 1, 1988

By Baafi EY, Chatterjee PK

The quality of mine planning decisions ultimately depends on reliable estimates of the characteristics of the orebody. The quant- ifiable factors such as grades or thickness can be estimated from field data gathered from outcrops or exploratory drillholes. Since outcrop data is necessarily limited to the periphery of a deposit, extensive drilling generally is required. This paper outlines a method for selecting the number and location of additional exploratory boreholes using an iterative procedure based on a mathematical optimization concept called fixed point theory. The method is illustrated through its application to an exploratory drilling program for a coal mine where optimized locations gave a lower estimate of regional and block variances than a manual Choice.

Jan 1, 1986

By Koppe J. C

This paper describes the methodology developed to establish a sequentia mining plan applied to a coal mine, using computers. Firstly, isocontou. maps were generated from the drill holes and outcrop description information, representing the thickness and depth of the rock formation: present in the mine site. The procedure relies on the repeated application of the cross validation techniques, until the standard deviation of thi estimation is reduced to a minimum.From this map the coal reserves of the two coal seams, the overburdet (separated in hard and soft material) and the interburden were calculated After that, the maps were transferred in digital files to AutoCAI software, where different mining plan simulations were performed. 7b ore evaluation in each case was done automatically, including tonnages volumes and stripping relations. The final mine configuration consider the economic aspects of the operation.

Jan 1, 1993

By Membrey W. B, Partridge A. C

Lower transportation costs, improved handling and better utilization efficiency are some of the reasons that make low moisture coal product desirable. There has been considerable interest in the development of effective coal dewatering techniques to achieve this result. One avenue of considerable merit for enhancing dewatering processes is by modification of the surface chemistry of the coalwater slurry system by chemical means, resulting in better performance of existing equipment. This paper reports the results of an investigation of the utility of surface active agents in the enhancement of fine coal dewatering. A large variety of proprietary dewatering agents have been studied in relation to their efficiency in enhancing the dewatering of a number of Australian coals. Properties of particular coals that make them amenable to improved dewatering by particular chemical agents have been identified. Surface studies, including surface tension and zeta potential measurements as a function of surfactant concentration, as well as dewatering assessments, were used. Particular attention was paid to filtration, but the results could be applied to other dewatering systems.

Jan 1, 1989

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

The problems encountered with the introduction and use of Isanol underground are described. Significant direct as well as indirect savings have resulted from the use of Isanol. Field studies have shown that the concentration of common gases released during detonation is considerably lower than with conventional nitro-compound type of explosives.

Jan 1, 1977

By M Haest, S Sandler, R Botha, H Lang, K Hume

Benchmark practices in the mining industry include the establishment of Quality Programs — Quality Assurance and Quality Control (QAQC) — to monitor the correct execution of sampling protocols and control each stage of the ‘Sample Cycle’: Sample Collection, Preparation (comminution) and Analysis. QAQC reports commonly include statistical-numerical results that quantify performance of QAQC controls (field duplicates, preparation duplicates, blanks, standards etc). Graphics such as scatter plots, QQ plots, histograms and cumulative frequencies are used to represent the results. Statistical values including relative difference, absolute difference, relative variance, averages, T-test, and Zscores are used to quantitatively express the relationship between duplicate pairs ... but is an effective quality program just a statistical exercise? This paper aims to highlight the concept of ‘Quality Management’ (QM) as the precursor of continuous monitoring (ideally in real time) of QAQC results on Exploration, Production, Processing and Port samples, determined by trend analysis performed on a time and/or grades basis. Currently, there is a paradigm in the process of quality assurance that if individual data points fall within a predetermined acceptance limit then they are ‘acceptable’ and therefore suitable for informing operational and investment decisions. However, what is stated with respect to QM is that sometimes results found within the acceptance limits can indeed be internally biased, or show material deviations over a period of time, thereby impacting reconciliation results and/or potentially creating discrepancies with the final buyers. QM refers to the proactive detection of these ‘anomalous tendencies’, the approach and communication with the source of the information, the understanding of the reasons that cause the deficiencies, and the generation of agreed action plans to remediate the situation and ensure the consistency of results, in other words: continuous improvement on proactive manners.

Mar 22, 2022

By Ranklin W. J

The mechanism and rate-limiting step of carbonaceous reduction of zinc from slags was investigated in the laboratory. Disks of graphite were rotated in ZnO-containing slags at various speeds for fixed periods at 1250 to 1325¦C. The mass loss was used as a measure of the amount of ZnO reduced. Application of the Levich equation indicated that at rotation speeds at which it is valid, the reduction was chemically controlled with an activation energy of 27 kcal/mol. At zero rotation speed the reduction of ZnO by carbon appeared to be slag-phase mass transfer controlled with an activation energy of 38 kcal/mol. An increase in the FeO content of the slag increased the rate of reduction while an increase in sulphur content decreased the rate of reduction. When FeO was present in the slag, reduction appeared to occur by a combination of indirect reduction of ZnO by carbon and by reduction by FeO with reduction of Fe203 back to FeO by carbon. The effect of sulphur was consistent with a surface blockage mechanism due to the surface active nature of sulphur in slags.

Jan 1, 1993

Mid-ocean ridges host approximately 65 per cent of about 100 known sites of high-temperature venting and polymetallic sulfide deposits; most of them are located at the East Pacific Rise (EPR), while more diverse mineralisation styles occur at the Mid-Atlantic Rise (MAR). Seafloor hydrothermal activity at the EPR are related to MORB while different substrates, including MORB and ultramafic intrusive rocks, are associated with æblack smokersÆ at the MAR. Depth of hydrothermal activity ranges from 0.7 to 4.3 km. High-temperature vents precipitating Cu-Fe sulfides (chalcopyrite and isocubanite, rare bornite), pyrrhotite, pyrite (¦ marcasite), and sphalerite, and low-temperature edifices precipitating marcasite (with pyrite), sphalerite, barite, andsubordinate chalcopyrite (pyrrhotite and isocubanite are absent) occur in both environments. There are considerable differences in Fe, Zn, Cu, Ag, Au and trace element contents in ores and in theFeS contents in Zn-sulfides in these deposits. Acomparison with anhydrite and sulfide minerals precipitating from modern black smoker fluids sulfide reveals many similarities but also some important differences. Fluids with salinity values above and below that of seawater at 400¦C down to 130 - 170¦C deposited sulfide minerals. Mantle-derived He prevails in fluids trapped by sulfides in EPR 9¦N and 21¦N hydrothermal systems. Hydrothermal fluids in MAR and back-arc systems are richer in radiogenic 4He. The sulfur isotope composition varies in the different hydrothermal fields and within zones of a chimney. EPR sulfides display narrower range of d34S values, while MAR and back-arc sulfides can bedepleted and enriched in the heavier d34S isotope. The most important finding is that fluid temperature, salinity, R/Ra ratios and d34S values ranged more significantly in the polymetallic sulfide deposits than when measured directly on venting fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008