Search Documents

By D Clarke, I Minniakhmetov

This paper describes the application of the SBRE framework to model the Olympic Dam deposit, one of the largest copper and uranium deposits in the world. Geostatistical simulations are the best practice for quantifying uncertainty in the mineral value chain and estimating resources. However, these simulations are currently undertaken on an ad hoc basis in the mining industry due to the high requirements in computing resources and capabilities in advanced geostatistics. The SBRE project provides a standard framework to test, build, and run conditional simulation workflows, which has been applied to the Olympic Dam deposit. Conventional geostatistical methods face challenges when modelling the Olympic Dam deposit, such as non-stationarity, non-linear correlations, and a large number of grid blocks to simulate. To address these challenges, a combination of methods was used, including projection pursuit multivariate transform, trend-residual decorrelation, pluri-Gaussian simulations, and turning-bands simulations. Various tools and applications were used to build the model, including in-house developed applications, Autovariogram software (Varify), and the RMSP python library. All computations were accomplished on the AWS cloud using the EC2-Batch service. The final set of simulations was validated using various methods, such as grade-tonnage curves, histograms, swath plots, and variogram reproductions, as well as validation using historical samples back-testing. The study highlights the importance of an automated, modular, and scalable framework in the development of conditional simulation workflows and describes the learning gained from trials of different combinations of methods and software

May 24, 2023

By K Mayank, A N. Mainza, I Govender, M Narasimha, A Mittal

In mineral processing industries grinding is the most energy-consuming process. A tumbling mill is an essential grinding equipment widely used for particle size reduction. Power consumption, impact forces and trajectory paths are critical parameters for characterising a tumbling mill to determine grinding efficiency. The effect of lifters and mill speed plays a vital role in such parameters. However, most of the studies ignore the impact of the lifter and do not investigate the effect of slurry dynamics on charge motion. The focus of the present work is to prepare a computational model that can accurately predict the complex multi-phase dynamics of charge particles, air and slurry inside the mill using a model that couples computational fluid dynamics (CFD) and the discrete element method (DEM). The details of impact forces with lifter profiles and mill speed variations will be refined even further using the CFD-DEM coupling approach. The slurry-air free surface is modelled using the volume of fluid (VOF) method, and the charge motion is modelled using the DEM. The phases are coupled using the interface momentum exchange between the charge and the fluid slurry. The coupled model is validated against experimental results from the positron-emitting particle tracking (PEPT) data. The validated model compares the effect of slurry content on charge dynamics with the dry DEM model. The presence of slurry is observed to dampen the tangential and shear contact forces.

Aug 24, 2022

By J Purandare, D Murdoch

The goal of the life-of-mine plan is to ensure that while the site is left safe, stable and non-polluting, the landscape is such that optimal use can be made of the site post-mining and closure. However, in the face of evolving shareholder expectations and the current international economic climate, numerous mines are ceasing operations and moving into a care and maintenance phase. These changes bring with them a high degree of community concern, not only about the potential legacy of closed operations, but also those mines that continue to operate.While mines across Australia are committed from the earliest planning stage to develop clearly defined post-mining land use and landform objectives, broader expectations related to these objectives may change and evolve during the life of the operation. This is especially the case where a mining operation has a project approval where the land use objectives are aligned to land capability and land use commensurate to that which occurred premining. CITATION:Murdoch, D and Purandare, J, 2016. Optimising land for beneficial use during and after mining, in Proceedings Life-of-Mine 2016 Conference, pp 166–167 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

By Grinbaum B, Stevens G. W, Dalton R. F

Many hydrometallurgical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process which produces a bleed from the electrolysis tank house in the form of a concentrated sulphuric acid stream. Currently, the bleed stream is necessary to remove impurities such as iron that decreases the efficiency of the electrowinning process. However, this comes at a high financial cost owing to large quantities of make-up sulphuric acid required. A process has thus been developed with Zeneca Specialties (UK), ICI Australia and Gunpowder Copper Co at the University of Melbourne for the recovery of sulphuric acid from copper tank house bleed liquor. The recovery process uses the method of solvent extraction. Solvent extraction has the advantage of being a well-established technology in the mining industry and will reduce the environmental impact of the S/X-E/W process, as all additional chemicals can be completely recycled. A simplified diagram of the process is shown in Figure 1. Tank House

Jan 1, 1997

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011

By G Byrne, A Bowden

There is often a difference in opinion about the allocation of risk in the establishment of mine closure bonds or financial assurances. From the State’s perspective, protection is needed to ensure that the broader community is not left with the liability of properly closing a mine in the event of a default by the mine operator. Such a default might occur where an operator decides to abandon a site, perform incomplete rehabilitation, becomes insolvent or claims limited liability. On the other hand, mine operators who can demonstrate a strong financial position plus a record of social and environmental commitment and performance, argue that there should be some recognition of this in setting a bond that is less than the full cost of early closure. They argue that a mine rehabilitation bond based on the full cost of early closure is overly conservative and ignores the actual risk of the operator being in default. This paper examines an approach that incorporates the risk of default into the establishment of mine closure and rehabilitation bonds. CITATION:Bowden, A and Byrne, G, 2018. Mine closure bonds (financial assurances) – the ‘how much?’ conundrum, in Proceedings Life-of-Mine 2018, pp 32–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Ghahreman‐Nejad, M Munro

Design of embankment dams often requires seismic analyses, or an assessment of earthquakeinduced ground and dam movements. There are a large number of cases where earthquakes have triggered sliding and lateral spreading of embankments, resulting in excessive crest settlements. In some instances, liquefaction and embankment failure has occurred resulting in loss of containment. Hence, evaluation of the effects of earthquakes on embankment dams is a critical design aspect. This paper discusses the methods and the results of a seismic liquefaction assessment and deformation analyses of a tailings dam. The tailings dam consists of a perimeter earth core rockfill starter dam which has been raised using upstream construction methods. The embankment raises (formed by an upstream clay blanket and an all-in rockfill body) are constructed over the impounded tailings, which are potentially liquefiable. Extensive field and laboratory tests were undertaken to assess the liquefaction potential of the tailings, and also determine the material properties required for seismic stability and deformation analyses. Numerical modelling of seismic liquefaction and deformation was carried out using FLAC (Itasca 2016) to predict the magnitude and spatial variation of deformations that may lead to an uncontrolled release of tailings. Primarily based on a parametric assessment of UBCSand and Finn-Byrne constitutive models, the results of the analyses are presented and compared for evaluation.

Jul 1, 2021

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A Densten, C Gimber

Surface water management and drainage is a key aspect of mine rehabilitation and closure planning. In the authors’ experience, drainage related problems are amongst the most common forms of failure in mined landscapes. The appropriate design of surface water infrastructure is therefore a key focus of practitioners. While there is currently a trend towards distributed drainage networks and avoiding hard engineered structures, in many situations (especially for existing landforms) engineered drainage structures cannot be avoided. CITATION:Gimber, C and Densten, A, 2018. A risk-based approach to drainage design standard selection for mine rehabilitation and relinquishment, in Proceedings Life-of-Mine 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Ashford, Minniakhmetov

Geostatistical simulations are the best practice for uncertainty quantification in non-linear systems. Simulations are currently undertaken on an ad hoc basis in the mining industry due to high requirements in computing environments and advanced geostatistics. In contrast to the estimation process, multivariate simulations can be performed using different methods, tools, and computational environments, similar to data science. For large companies with multiple commodities it is important to have a standard framework to test, build, and run workflows using different methods, applications and computational environments. This work presents an auditable, modular and scalable framework to create geostatistical simulation workflows where the workflow is abstracted from the implementation. Key aspects: automation – workflows should be able to run automatically given updated data (if hands on modelling is not required); auditability – workflows should document key considerations and parameters; modularisation – workflows should permit swapping out components, for example substituting domaining in Leapfrog software with automated domaining using machine learning scripts; scalability – easy, repeatable, portable deployments on diverse infrastructure (for example, experimenting on a laptop, then moving to an on premise cluster or to the Cloud); reproducibility – parameters should be archived to permit re-running and reproduction of workflows in future years; and sensitivity analysis – any component of a workflow should be able to run with multiple scenarios of parameters and data to enable global uncertainty quantification and sensitivity analysis. The presented framework can be used to create different workflows for geostatistical simulations in multiple assets to quantify uncertainty in the value chain for resource categorisation, reserves uncertainty, value of information and robust mine planning amongst others.

Mar 22, 2022

By C A. Cooper, G A. Suter

The sizing of a starter dam for a Tailings Storage Facility (TSF) involves balancing many competing demands. It should cost as little as possible, be high enough to store tailings until the first raise can be constructed, it must be able to contain water safely, and it must be designed in such a way that the long-term integrity of the higher raises are not compromised, among other things. In addition to these demands there is the complication of the behaviour of the process plant, and the tailings during commissioning. Variations in slurry density, excess water in the TSF, initial settled density of the tailings, reliability issues, and beach slopes above and below water can all impact the way the tailings beaches are developed and ultimately impact the ability of the starter dyke to contain the required volume of tailings and water.The conventional approach to the design of a TSF starter dyke is to begin looking at the elevation required for a set of deterministic design parameters, find ways to reduce the size or volume of it as much as possible to reduce cost, and then possibly look at the sensitivity of some of the input parameters. This paper discusses a stochastic modelling approach for starter dykes that allows a wide range of design inputs to be simulated quickly, with an envelope of possible results produced. The sensitivity to different parameters can also be examined to understand which design inputs have the biggest impact on the required dyke sizing. By integrating the 3D TSF modelling tool Muk3D with GoldSim, it will be demonstrated how a wide range of scenarios can be evaluated and how that information can be used to make better decisions about the selection of design options.CITATION:Cooper, C A and Suter, G A, 2018. Starter dyke optimisation with Muk3D and GoldSim, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 466–475 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M Norbert, C Bennett

The Legacy Way Tunnel was constructed from Toowong to Kelvin Grove in Brisbane, and is the first large-scale underground excavation in the Bunya Phyllite in Brisbane. The Legacy Way Tunnel is 4.3 km in length, comprising two mainline tunnels excavated by a tunnel boring machine (TBM) with 46 connecting passages excavated between the mainline tunnels for egress provision and services. The Legacy Way Tunnel passes through two geological formations, the Bunya Phyllite and the Neranleigh Fernvale Beds. The Bunya Phyllite is the dominant formation of the Legacy Way Tunnel, extending for three quarters of the tunnel prior to intersecting the Normanby Fault Zone (NFZ) and the Neranleigh Fernvale Beds. The NFZ forms the contact between the two formations as part of the Brisbane Metamorphics, which underlies the majority of Brisbane City. The development of the geological model and the understanding of the ground’s reaction to tunnelling was an iterative process. The tender phase investigation data has been supplemented with additional design phase investigation boreholes, geophysics and walk overs. Aerial photograph interpretation coupled with borehole data allowed the development of the domains along the length of the tunnel. Early excavations for the spoil conveyor tunnel and borehole data from subsurface instrumentation installation provided the first construction phase data followed by the commencement of tunnel boring machine (TBM) excavation. Routine cutterhead inspections coupled with ongoing reviews of the predicted geology resulted in clear response triggers to selection of segment types while detailed inspections in passage locations provide the initial classifications for segment removals.CITATION:Bennett, C and Norbert, M, 2014. Tunnelling within the Bunya Phyllite of Legacy Way, Brisbane, Queensland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Ellis

In January 2008 Chirano Gold Mines Limited committed to expansion of the Chirano Gold Project from its existing design capacity of 2 Mtpa ROM ore to a new design value of 3.5 Mtpa. In addition to increased throughput, the design had to contend with increasing ore hardness and competency, while at the same time make cost effective use of existing equipment with minimum disruption to existing production. The solution adopted involved some novel approaches including tertiary crushing and operation of the SABC circuit in overflow ball mill mode and parallel elution with a common acid wash column. This paper describes the approach taken to the design of these elements to achieve a cost effective and safe capacity expansion.

Aug 8, 2011

THE object of this note is to set forth some particulars of the effect of light on cinnabar occurring in a deposit of this mineral at Puhipubi, in the North Auckland peninsula of New Zealand. This deposit is contained within a gently-inclined sheet of siliceous sinter forminga hillock called Mount Mitchell, and is particularly notable in that it is an instance of the simultaneous deposition of cinnabar and silica on a large scale. The mercury-bearing material varies in character from semi-porous sinter to dense translucent cbalcedony, of which the former is stained to various shades of pink, the latter to brilliant reds and vermilion. On exposure to daylight-and particularly to sunlight - these colours change to corresponding shades of translucent bluish-grey. As a direct result of this change the Mount Mitchell deposit remained unknown until some ten years ago, for, while prospectors early discovered cinnabar in the adjacent city and in a neighbouring stream bed, none of them recognized this mineral in the bluish chalcedony strewing portions of the surface of the Mount. The writer has carried out a series of experiments designed to indicate the cause and nature of this change, and to form a basis for the elaboration of more delicate experiments which would yield positive information. Circumstances, however, have so far combined to prevent the continuation of the research, and, as there seems little prospect of the writer being able to do more work on the subject, it seems well to publish the data so far obtained. Prior to describing this colour change, the writer would point out the desirability of restricting the meaning of the term cinnabar to the naturally occurring red sulphide of mercury; this would eliminate the ambiguities which arise from its indiscriminate application, in chemical literature, to both natural and artificial sulphides. Further the term cinnabarite having long since fallen into disuse, there appears to be no good reason for retaining the companionterm "metacinnabarite" when reduction to "metacinnabar" would preserve the meaning in a less clumsy word.

Jan 1, 1923

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

By Richards JR, Herbert HK

A basic question in preparing this review was how to define sulphur mineral occurrences as being associated with the Pacific Rim. This question will be reconsidered later. The isotope composition of sulphur- containing minerals may be considered in terms of two primary sources - 1. deep- seated sulphur, devoid of crustal contam- ination with a 634S value near 00/0o and 2. oceanic sulphate which fluctuated in value between +10 and +300/00 over geological time (Claypool et al., 1980). However, minerals have seldom been directly derived from these primary sources as even evaporites have been dissolved and reprecipitated. The marine source is differentiated biochemically and isotopically in recent sediments where sulphide from bacterial sulphate reduction may be significantly depleted in 31S. The question of chemical interaction of ascend- ing magma with upper crustal rocks has become one of degree rather than whether or not it occurs. Mineral deposition is considered increasingly in terms of mixing of fluids and their chemical reactions with rocks rather than direct precipitation from magmas or hydrothermal fluids derived from them.

Jan 1, 1987

Mining of copper ore is still the most important business in Chile. In order to mine ore with a copper content of less than one percent at Minera Los Pelambres in an economical way, opencast mining is mandatory. Due to the prevalence of avalanches at the mine, the concentrator was located in a stable area, some distance from the mine. As a consequence, the material has to be transported between mine and concentrator by conveyor. A downhill conveyor system has been implemented for more than ten years as the most suitable and most economical ore transport alternative. Due to the length (12.6 km) and inclination (1300 m drop) of the conveyor system, the stresses in the steel cord belt are the dominant design criterion, resulting in a belt quality of ST 7800. Additional dynamic belt stresses during transient operating conditions are avoided by the installation of high capacity adjustable frequency drives. The rating of a single drive unit is 2500 kW. During ten years of operation, several capacity increases have been implemented, from an initial 5800 t/h up to the current capacity of 9900 t/h. This presentation describes the engineering challenges of the implementation of the world's strongest belt conveyor system. Capacity increase measures like the development of new control and breaking strategy, proved by dynamic simulation of belt forces and belt speed scenarios are explained. During this long-term partnership of RWE Power International, the former Rheinbraun Engineering, with Minera Los Pelambres, RWE has been engaged continuously for development work, safety checks, expert opinions and maintenance audits, and giving new impulse to conveyor technology.

May 1, 2010

Average annual growth in consumption of primary energy in Australia over the past ten years has been 5.5% compared to a world average of 4.1%. Over the next ten years growth rate is expected to increase to 6% per annum due largely to the rapid development in the mineral processing industry. By the end of the 1970's natural gas is expected to supply more than 9% of Australia's, primary energy market. Coal will supply 40% and petroleum products 47%. Nuclear energy will make its appearance but-will only make a small contribution in the period. Australia has adequate reserves of natural gas and coal to supply its needs in the 1970's and beyond. However the newly developed reserves of crude, while supplying 60-70% of requirements-in the initial years; will need regular and sizable additions if they are to .keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated *that new discoveries-will need to approximate. ten times the volume of recoverable reserves found in Australia to date. .

Jan 1, 1970