Search Documents

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By C Laming, P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Reconciliation is a powerful tool used by mining operations to compare the mass and grade of ore produced with what was estimated before mining. The primary objective of reconciliation is to verify that the estimated planned metal production is achieved during processing, allowing issues to be identified for which adjustments can be made throughout the mining value chain to improve recovery and maximise efficiency. Traditionally, the mine plan is based on estimated mine grades using sampled exploration drill hole or blasthole grades. Reconciliation discrepancies between the mine plan and mill are common due to such factors as insufficient or non-representative sampling, poorly conceived models, or unrecognised blast movement. MineSense Technologies Limited® (MTL) has developed an X-ray fluorescence (XRF) sensor-based ore classification system that is installed on mining equipment to provide real-time grade estimates of run-of-mine material at bucket, truck, or belt-scale. Bucket level grade estimates provide insights into grade variations at the mine face that were never before available. This data set eliminates some of the leading causes of reconciliation discrepancies and enables tracking of tonnages and grades from the mine face to the processing plant at bucket resolution with confidence. Bucket-by-bucket grades at the mine face enable dynamic optimisation of the mine plan to stabilise the mill feed grade through blending of mine and stockpile loads. Beyond stabilising feed grade, Mine to Mill reconciliation combined with the full XRF spectrum response can generate proxy relationships to ore characteristics like hardness and recovery. These properties can then be predicted at the mine face, enabling further optimisation of the downstream mill feed, not only for grade, but also for power and water consumption, reagent addition, and recovery. This paper presents the benefits of MTL technology for grade reconciliation and mill performance optimisation at a Cu Mine in BC (Canada).

Mar 22, 2022

By C Hawtin, B Miller, D Ashton

Ernest Henry mine (EHM) is an Iron oxide copper-gold sublevel cave mine located 30 minutes north of Cloncurry in North-West Queensland. The underground mine lies beneath open pit excavations, which were in operation from 1999 to 2011. Fault structures carry large quantities of water from the cover sequence aquifer into the underground mine area. The open cut excavations exacerbates vulnerability of the underground mine to the high intensity wet season storms of northern Queensland. These factors combine to make hydrogeological issues high priority for mine operation. Water-related risks include the cost of removing water from the mine, flooding risk and mud rush potential.Turnover of key technical staff in late 2015 at EHM resulted in the mine being left in an untenable position of losing the primary source of technical knowledge. Due to encouragement of cross-disciplinary activity coupled with workload and resource sharing, the management team were confident in utilising on-site personnel to offset loss of experienced personnel.Remaining geology personnel took additional responsibility for hydrogeological monitoring equipment and planning of upcoming work. Consultant input was limited to review only and an emphasis was placed on knowledge transfer to the geology team. Using this strategy, a 13 hole dewatering program was successfully implemented, achieving a significant water level drop in areas of elevated hydrological risk, whilst also upgrading the hydrological monitoring sensor array.Through a development program centred on cross-disciplinary exposure, the technical team was able to retain key technical knowledge despite staff turnover and produce strong results outside traditional training and roles. This paper serves as a case study on the methods, strengths and drawbacks of putting a focus on cross-disciplinary exposure as a method to combat staff turnover.CITATION:Ashton, D, Miller, B and Hawtin, C, 2017. Go with the flow – managing hydrogeological staff turnover at Ernest Henry mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

This talk was delivered in Kalgoorlie in April this year, to the Kalgoorlie Branch of The Institution of Engineers, Australia. We believe it is of such interest to members of our Institute and readers of this publication we believe it important to extend the audience who have the opportunity to read it. An edited version follows:"Why should we be so concerned about Mining Related Education; after all is said and done, the mining industry is not a great employer of persons?"The mining industry is capital rather than labour intensive. It employs only 2.7 per cent of the national workforce. However; the minerals industry is Australia's major exporter accounting for over 40 per cent of the nation's total export of goods.In Western Australia the value of minerals production in 1985 was about $5,000 million and consequently mineral exports accounted for about 53 per cent of the total value of overseas exports from the State. The diversity of the mining industry is also worthy of mention and produces iron ore, alumina, gold, nickel and mineral sands. That apart, our potential to become a major producer of diamonds, rare earths and petroleum products is considerable, not to mention base metals (copper, lead and zinc) and uranium.Our mining industry is of national importance and contributes in excess of 30 per cent of the total value of Australian overseas trade. Although the mining ind ustry does not employ many people, the people it employs contribute very much more, per capita, to the wealth of the nation than do employees in any other sector of our economy.No-one would deny that during the 20th century Australians have depended on the export earnings from the sale of relatively unprocessed agricultural products and more recently the sale of relatively unprocessed minerals for their standard of living.Not surprisingly, therefore, our economy is highly vulnerable to unstable world commodity market prices.The slump in trade we are currently experiencing (in first quarter 1987-Edition) was brought about by the over supply of the raw materials we produce. However, the recent downturn in world market prices is more serious than previous slumps because in part it is due to technological advances 'in other countries which could have a permanent effect on the world trade of primary products.

Jan 1, 1987

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

By J A. de la Torre, I R. Cerna, G K. Karadjian

The La Colorada underground mine in Zacatecas, Mexico is a mechanised cut-and-fill silver mine with a capacity of 1250 t/d. The project focused on training the mine’s experienced operators for a fleet of underground trucks, through the use of a training simulator. The project was run by the simulator vendor, in collaboration with the mine’s maintenance, safety and production management.A training program was created targeting maintenance reduction, productivity improvement and increased utilisation and availability. Operators were first acclimatised to the simulated environment, had their current performance baselined, then received targeted coaching, with the process repeated to reinforce learnings. Concurrently, production, maintenance, and safety data was being measured in the real world to measure skills transfer. Due to limited telemetry available from the equipment, many of the data points for the project were sourced from maintenance logs, and accounting data.Equipment failure data measured from unscheduled maintenance records showed an overall 6.5 per cent decrease in unscheduled maintenance following the implementation of the training program. This rate of reduction correlated with the significant decrease in equipment abuse behaviours measured within the simulator during this period. Additionally, overall maintenance activities showed a significant decrease, confirming that reductions in unscheduled maintenance were not achieved through increases in scheduled maintenance. The reduction in equipment damage also increased availability and utilisation of the truck fleet. This highlights that the maintenance improvements not only reduced maintenance costs, but made the fleet available for more production. Moreover, the variability of the operator performance was decreased by 86 per cent, and the difference between their best operator and the worst is less than the baseline; this showed a gap where machine abuse, productivity and cost are impacted directly.This project illustrated that even small-scale mining operations with an experienced operator workforce can achieve positive return on investment (ROI) from simulation-based training. It also highlights that in the absence of equipment telemetry, alternative data sources such as accounting data and maintenance logs can be used to quantify ROI from training.CITATION:Karadjian, G K, de la Torre, J A and Cerna, I R, 2017. Innovations in underground hard rock operator efficiency – through simulation-based training technologies and processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 53–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By D Syme

In the middle of 2000, BHP Billiton implemented a Six Sigma Plus business improvement program known as Operating Excellence. It was developed based on a business bottom line initiative to deliver 35 - 40c/share and was one of the BHP Billiton strategies to deliver $2 earnings per share and a longer term $40 share price (BHP share price). Cannington is a silver, lead and zinc mine owned and operated by BHP Billiton. Through implementing Six Sigma Plus Cannington wanted to:have in-house capabilities to change and improve; tailor for the needs of each business unit and department; have æSharing of its KnowledgeÆ as a tool for improvement and have a competitive edge across Cannington û to be better than our competitors; learn from and leverage off the successes of improved safety and prior business improvement efforts; and ensure networking and sharing of information have common measurement systems across all assets. As with most business improvement programs û Six Sigma Plus was met with some degree of skepticism, especially given the amount of resources involved. After 18 months, much of this skepticism has been replaced with enthusiasm as peopleÆs understanding and acceptance of its fundamental concepts are being realised. The idea behind Six Sigma Plus is that it combines sound technical solutions with high acceptance by those who need to work with or implement the change. The future vision for Six Sigma Plus is that it become part of what we do at Cannington û just like safety and environment û so that Six Sigma tools and methodologies are used in our every day work.

Jan 1, 2002

By A Bagis, T Baker

In 1983 the New South Wales (NSW) Government began to construct a 35 km freight rail line to provide additional rail capacity to Port Kembla in the Illawarra region, south of Sydney, through a direct connection between the Unanderra to Moss Vale line at Dombarton to the Main South rail line at Maldon in the Southern Highlands. The project area lies within the carefully managed Sydney Water catchment and is also underlain by previous coal mining activities.Construction of the line halted in 1988 prior to its completion after the NSW Government reassessed the demand case and found that the project was not as viable as originally forecast. However, by this stage the line was partially constructed, including the majority of civil earthworks, approach structures to the main river crossings and establishing the portals for the Avon tunnel as a precursor to major tunnelling works.In 2012, the Commonwealth Government funded Transport for NSW to undertake the necessary engineering and environmental preconstruction works. Most importantly here, the 1980s rail link was predicated upon the use of electrically powered locomotives, whereas the locomotive fleet in operation today in NSW is diesel powered. This fact has a significant impact upon the approach and development of the Avon tunnel section, as the diesel powered locomotives combined with the length and grade of the tunnel alignment produces a unique set of conditions requiring specialist engineering design and systems to ensure safe and functional operation of the railway through the tunnel section.Given the above, the Avon tunnel will need to be supported by a ventilation and smoke control design based on the heat rejection from the locomotive consist, consideration of ambient air quality compliance, comparison against in-tunnel air quality goals, and providing safety systems in line with the fire and life safety strategy it requires.This paper explores the current development of both the tunnel civil works responding to the geography, geology, rail functional requirements, as well as the tunnel ventilation systems being revised to suit the diesel locomotives.Further, this paper describes the importance of combining the design outcomes with the procurement methodology in order to achieve the project objectives, a functional outcome and value for money across the project life.CITATION:Baker, T and Bagis, A, 2014. Maldon to Dombarton Rail Link – design development of the Avon Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Viviers, G Ratner

Ventilation is part of all underground mine operations and is undertaken in order to introduce fresh, cool air to the workings and to remove stale, affected air. It is problematic to obtain efficient and accurate estimates of volume flow and static pressure in the installed operational configuration for the auxiliary axial flow fans.An empirical method was developed to estimate the static pressure and volume flow through a calibrated differential pressure port on axial flow fans. Prior to shipping, each fan is performance tested according to BS 848 (ISO 5801) to establish the fan performance curves. In addition to the standard required parameters captured to fully describe the performance, the differential pressure is measured across the fan rotor to enable correlation with the characteristic fan curve.The method was implemented on a ruggedised tablet PC platform. This compact platform is then used to calculate the volume flow rate from the differential pressure sensor measurement input via a USB port. The result is a real-time measurement of volume flow and operating point of the fan system. This can be used effectively in overall modelling of the mine auxiliary ventilation systems and calculation of system resistance could provide a health indication of the fan and duct system.CITATION:Ratner, G and Viviers, S, 2013. Underground auxiliary ventilation monitoring and diagnostic system, in Proceedings The Australian Mine Ventilation Conference , pp 57-62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P J Savory

Ranger is a uranium mining operation located within one of the most environmentally sensitive regions of Australia. Geology has played an important role in mine planning, operations and rehabilitation since discovery of the deposits 25 years ago. The Ranger orebodies have a reserve total of 166 300 tonnes of U308 including 90 400 tonnes of U308 at North Ranger. At current milling rates these reserves give a mine life greater than 40 years. The uranium is hosted in Lower Proterozoic rocks of the Cahill I ormation and is associated with strong chlorite alteration. In pit grade control involves the use of calibrated probes and a radiometric truck discriminator allowing fast, accurate grade determination of material. Ore is defined at a cut-off grade of 0.2 per cent U308. Mineralised material is defined by the Uranium Mining (Environmental Control) Act 1979 (UMEC Act) at a grade of 0.02 per cent U30s. Natural water levels in the #1 Pit area vary as much as 7.5 metres between wet and dry seasons. Ground water inflow into the pit during the dry season is 600 m3/day. No significant slope failures have occurred in the pit. The environmental impact of mining operations is constantly monitored. Rehabilitation of non-mineralised stockpiles is ongoing. This paper discusses the interaction between geology, hydrogeology, rock mechanics and grade control with the present mining operation.

Jan 1, 1994