Search Documents

By A Quigley

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over 3 km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods.The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters.The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models.

Jan 1, 1999

I am very grateful to have the honor of delivering this Key- note Speech to all of you here today, to the Chairman Mr Cope- man, and to all the organisers. As you heard, I was mainly involved for a very long time in the purchase of iron and steel raw materials for Nippon Steel Corporation. Today, however, I would like to talk to you about a much wider issue, namely, how the Japanese steel industry is going to change towards the 21st Century, and what will be the main technical innovations and trends behind those changes. I will also mention the effect that the changes are likely to have on the procurement of raw Materials.

Jan 1, 1988

By Kidman B. E

The Fitzpatrick area is the deepest section of the North Mine, with the orebody located between 1450 and 1800 m below the surface and some 600 m NE of the main No. 3 Shaft orebody and separated from it by the intensely sheared Globe Vauxhall Shear Zone. Development towards the Fitzpatrick area commenced in 1977 after earlier initial exploration drive development. However, it was not until 1982 that mining in the Fitzpatrick area actually began with the silling out of No. 36 level at a depth of some 1600 in. Since that time mechanised cut and fill mining from an incline ramp system with connecting stope accesses has progressed some 25 m above No. 36 level. Initial sill development on No. 37 level at 1660 m depth also commenced in July 1987 to further develop the Fitzpatrick area.

Jan 1, 1988

By Conochie DS

SIROSMELT is a successful new pyrometallurgi- cal furnace system using a top-entry lance which can be submerged in both slag and matte. The lance is of simple construction, and is cooled by process air. Pilot plant work commenced in the CSIRO Division of Chemical Engineering in 1972 using a 50 kg batch reactor. This paper traces the development of the technology through various slag cleaning and smelting processes up to a scale of 5 tonnes per hour continuous feed. Strong co- operation between CSIRO and the Australian smelting industry has contributed greatly to the success of SIROSMELT.

Jan 1, 1984

By M Bannear, J-F Wilhelmy, R Jones

Mineralogical study of the interactions between fluxes and iron-oxides helps to understand how magnetite oxidises to haematite during pellet firing. Samples of OneSteel magnetite pellets tested at COREM pilot plant were collected after three firing steps and were studied mineralogically. Preheated pellets revealed no particular microstructures related to the composition of fluxes but were more affected by their bed position. After kiln firing, the impacts of lime and magnesia became more apparent. Magnetite oxidation is complete in the cooling stage. The position and the microstructure of the residual magnetite can bring useful information that could æcompleteÆ the view of the firing cycle.

Jan 1, 2007

Incompetent ore and country rock have caused stability problems in longhole open stopes. Fully grouted pre-placed cablebolts have reduced these by preventing ground relax- ation and joint dilation to maintain a self supporting rock structure. Larger atope spans can now be opened with the same or smaller pillar. Mining methods are expected to become less dependent on original ground conditions. Effect of spacing, orientation and stress distribution along the cablebolt is not fully understood at this stage and requires more Observation.

Jan 1, 1977

Geologists often classify ore textures on the basis of the origin of the rock in which they form and the grade of one or more minerals within the ore (Sinclair and Blackwell, 2002, pp 32-36).  Metallurgists, on the other hand, need to know how best to process the ore in order to extract the valuable minerals from it (Petruk, 2000). Geological classification has the following disadvantages:it requires the services of skilled economic geologists, of whom the supply has been dwindling for many years;it is subjective, depending on the perceptions of the individual geologists who make the classification; andit may relate only weakly to processing requirements of the ore. We describe methodology for automatic classification of ore textures from images of drill core. The images analysed are æclassifiedÆ images, in which a particular mineral (or mineral group) is assigned to each pixel. The new methodology is intended to:provide a quantitative and reproducible alternative to traditional geological texture classification,relate to process mineralogy of the ore, andimprove the ore-texture-related input to orebody domaining and geostatistical block models.

Jan 1, 2008

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

Production of refined zinc (99.95 per cent) at the minesite without increasing greenhouse gas emissions is considered. As an example, exploitation of the full reserve of the McArthur River orebody is proposed, using the existing concentrator, whilst introducing radically innovative smelting technology. Bulk flotation of all the sulphide minerals is followed by smelting in a melt circulation reactor with tonnage oxygen. By smelting the high-energy pyritic concentrate and reacting the evolved sulphur dioxide with near-mine dolomite, a large amount of electricity can be generated. This is enough to supply all the requirements for the smelter itself, an air separation plant and a facility for compressing and liquefying carbon dioxide. Carbon dioxide is disposed of off-shore for enhanced oil recovery or by other means. The reacted dolomite fixes sulphur as an inert and environmentally acceptable solid residue. Treatment by these means leads to virtually zero gas emission smelting. The paper concludes with a vision for the future in which expansion of zinc smelting capacity is seen to be definitely needed.

Jan 1, 1998

By Kuzugundenli OE, Nagaraj DR

Organic complexing agents have received special attention over the past few decades in the search for reagents for improved flotation separation of minerals, especially non-sulphides. The majority of such reagents that have been proposed over the past few decades have remained largely a laboratory curiosity, except perhaps alkyl hydroxamates, because their selection is seldom based on commercial viability. In this regard, the choice of complexing agents such as oximes may be more realistic because of their widespread use in solvent extraction of copper. Our earlier studies have confirmed that they are also effective as collectors for copper oxide minerals, including chrysocolla which is the most difficult copper mineral to beneficiate. The flotation behaviour of chrysocolla for several structurally-related hydroxyoximes were studied as a function of pH and oxime concentration and the role of structural features examined. The structural changes studied included substitutions in both chelating and non-chelating parts of the molecule. The results indicated that, contrary to expectations, many of the structural changes in the basic molecule, salicylaldoxime, do not have a positive effect on collector efficiency. The reduction in collector efficiency is rationalised on the basis of possible steric factors affecting complexation and packing of the collector species on the mineral surface as well as effects due to changes in electron density brought about by substituents. Introduction of alkyl substituents on the oximic carbon of salicylaldoxime yielded the highest collector efficiency.

Jan 1, 1993

By Zamora C

The performance of a system for detecting the onset of overloads on rod mills is described. The system has bee,, tested at CODELCO E1 Salvador Concentrator where, due t,, variations on size distribution of the copper ore feed, th' rod mill is frequently subject to overloads. The main inpur signal to the system is the rod mill sound, after being measured and analog conditioned. This signal and othe signals measuring the fresh ore feed and the mill watt addition are fed to a computer containing a simpl mathematical model. The model parameters are empiricall estimated and an analog output signal is generated, whic gives an early prediction of the overload condition. The experimental results described in this paper show that the overload condition may be predicted with an anticipation of about three minutes.

Jan 1, 1985

By P Andrieux

By 1996 ground control-related problems at Brunswick Mine had raised serious concerns regarding the safe and economical extraction of large portions of the reserves. These difficulties were mainly caused by high stress levels in pillars, instabilities resulting from wide spans supported by ageing support elements, and chronic difficulties supplying rock fill from the surface quarry to the underground workings, which resulted in many large voids remaining open for long periods of time. Significant changes have been implemented at the site since 1996, amongst which were a change of mining method, the introduction of paste backfill, the establishment of stress management measures, and the introduction of shotcrete on a large-scale. This paper focuses on the regional ground conditions associated with both the previously used primary-secondary mining method and the newly implemented pyramidal pillarless technique, as well as on some of the stress management measures implemented at the mine.

Jan 1, 2000

By Mackinnon I. D R, Glikson M

Samples from the Callide Coal Measures, Queensland, Australia, containing the minor maceral, micrinite, have been studied using optical and electron-optical techniques to determine the precise compositional and structural nature of micrinite when in association with vitrinite macerals. Emphasis has been placed on direct spatial correlation of optical and electron-optical data due to the fine grain size (90 per cent of the component) and, as such, should not be considered a maceral.

Jan 1, 1991

The Lake Rotokaua sulphur deposit, near Taupo, New Zealand, is a lacustrine sedimentary ore body, 220 acres in area and from 7 ft to 96 ft thick, containing, within the area drilled to date, some 20 million long tons of ore averaging 25% elemental sulphur in unconsolidated tuffaceous diatomaceous clay, overlain by about 120 ft of pumice sand and by the shallow Lake Rotokaua. An additional amount of perhaps 4 million tons of sulphur is regarded as probable in the area remaining to be drilled. Current economic studies cover the problems of mining an unconsolidated water-saturated formation with some residual thermal activity nearby; conservation and restoration after mining in a scenic recreation area; beneficiation of the ore and extraction of high- purity sulphur, principally for fertilizer manufacture. The deposit has additional importance as a pointer to possible further discoveries in the Thermal Region.\

Jan 1, 1971

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

Facies associations in the Okiduse Volcanics, woodlark island, suggest that two major volcanic centres erupted synchronously during the Middle Miocene. These centres are referred to as the Watou Mountain Eruptive Centre and the Uvarakoi Caldera. The Watou Mountain Eruptive Centre, centred on Boganuse Mountain in the Okiduse Range, was a typical, moderate-sized composite volcano (or stratovolcano). The seq-uence is readily divisible into lava (Boganuse lava unit), breccia (Nikuben breccia unit) and epiclastic (Talpas sandstone unit) dominant facies, typical of composite volcanoes. These facies girdle Boganuse Mountain and they are interpreted to represent vent, cone forming and ring plain associat-ions, respectively. These facies indicate a reconstructed volcano of approximately 1,700m height with a basal diameter of 7km. The presence of limited exposures of intrusive associated with the vent facies (Kuike'beimmicrodiorite) suggests that the volcano is only partially dissected. The Uvarakoi Caldera is a felsic volcanic system contrasting with the mafic Watou Mountain centre.

Jan 1, 1994

In a state-of-the-an review of predictive methods for longwall support load calculation, special respect is paid to those techniques which enable actual roof conditions and local lithology of strata to be involved. Principal systems of roof examination include the borehole perforation test and seismic velocity measurements. Roof strata stability is related to caveability classifications and roof inclination due to subsidence. The critical analysis of both load resistance prediction methods and roof stability classifications shows that each has its own value of reliability level. The present research opportunities analysed underline the significance of developing fully reliable prediction techniques as needed by the coal industry.

Jan 1, 1991

The production of synthetic crude oil requires a suitable coal or a coal extract modified by hydrogenation for pyrolysis. Existing classifications are broadly based on historical and current needs. One, Seyler's, is based on a visual display which can be used to present petrographic bounds. The analysis of the coal extracts from solvent hydrogen-donor testing allows an experimental limit to be described and a plant limit to be indicated. Australian black coals are discussed within these petrographic and plant bounds and their limitations as a feed for the production of synthetic crude presented. Potential uses for the aromatic liquid products are suggested. The application of the diagram as a screening procedure for sub-hydrous coals is described.

Jan 1, 1975

By R Graber, R Johnson

North American steelmaking practices have evolved based on access to iron ore raw materials containing very low phosphorus contents, typically less than 0.025 per cent P. Cleveland-Cliffs managed Tilden iron ore operation produces iron ore pellets exceeding 0.030 per cent P, which by global standards would be considered low phosphorus, but has limited penetration in the North American iron ore market due to phosphorus content. Recently cathodoluminescence microscopy has augmented more standard ore characterisation techniques enhancing our understanding of the genetic history and process mineralogy of TildenÆs complex martite ore. This paper highlights the unique capabilities that cathodoluminescence microscopy provides for phosphorus mineral identification in fine-grained iron ores.

Jan 1, 2005

By King D

Recent field experiments in the United Kingdom (Buchanan, 1979) have shown that the in-seam technique is capable of detecting a 1m fault in a 3m seam, at a range of 280m and with a resolution of ¦40m. Comparable tests in Australian collieries are proceeding. Although the practicality of an implementation of the technique on a routine basis remains to be demonstrated, the potential of the technique for the prediction of outbursts clearly warrants detailed examination. This potential will,depend, inter alia, on the level and scale of variations in elastic (and anelastic) properties of bodies of coal undergoing stresses associated with mining. Available data, mainly from studies of the seismic properties of gas saturated reservoir rocks, confirm the intuitive view that stress increases give rise to increases in seismic wave velocity and decreases in wave attenuation, markedly at low stresses (as pore spaces close with little resistance) but less so as stress increases. Such increases are of the same order as aniso- tropic effects, but should provide impedance contrast sufficient for detection by in-seam seismic methods. At higher stresses, cracks form within the rock mass. Results from research on earthquake prediction provide some clues to the behaviour of sedimentary rocks sub- jected to large stresses. In particular, the

Jan 1, 1980