Search Documents

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

By Tilyard P. A

Recent exploration has established depos its of nickel sulphide in several areas of Western Australia. To assist in their develop- ment Amdel has investigated the beneficiation of many samples from these deposits and has estab- lished flowsheets for the recovery of nickel values by flotation. Metallurgical data are presented for the samples according to four factors which were encountered in their respective treatments.

Jan 1, 1973

By Lovett EP, Johnson CR, Dunlop GA

Seven streams of a low tonnage pilot plant operation on Cu/Pb/Zn ore from the Golden Grove Project were continuously assayed using an AMDEL In-Stream Analysis (ISA) system. The ISA instrumentation is briefly described as is the calibration procedure employed. The successful application of this instrumentation in the dynamic environment of a pilot plant operation is discussed. The operational sequence of the Golden Grove pilot plant is outlined along with the original project objectives and how they were achieved by the implementation of ISA. Results for the different complex flowsheets used are discussed, followed by the perceived benefits of installing such equipment in this operation.

Jan 1, 1986

By Jepsen L, Gifford M, Thomas G. S

Mine planning requires careful prediction of both the head grade and tonnage of mineralisation. As part of the planning process, operators of the Murrin Murrin nickel/cobalt orebodies (located in the Eastern Goldfields province of the Yilgarn

Jan 1, 1998

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993

With the introduction of the Health and Safety in Employment (HSE) Act 1992 and the subsequent repeal of regulations pertaining to mining, there has been an upheaval of the management of health and safety in mines.  More than ever, employers know that they must ensure that their workers are competent to carry out their assigned tasks.

Jan 1, 1997

The role and policies of the Aboriginal Sacred Sites Protection Authority are described in conjunction with the provisions of the N.T Aboriginal Sacred Sites Act 1978. Comment is made on the application of the legislation and these policies to development proposals in the Northern Territory. A brief review of criticisms by both developers and Land Councils is provided together with responses to these Criticisms.

Jan 1, 1984

Supergene enrichment of ilmenite occurs through a complex series of reactions with initial oxidation and hydration followed by leaching and dehydration. Lateritization appears to be associated with the early phase of the supergene process and if ilmenite grains are encased in iron oxides no further alteration proceeds.

Jan 1, 1986

By Morrison R

Optimisation has two distinct applications in the concentrator ò the first is in the area of the flowsheet and the operating parameters of the various unit operations ò the second is associated with the higher levels of process control. The Plant Metallurgist is faced with a library of complex theories relating to optimisation. The practical reality of optimisation lies in a combination of steady state simulation to ensure that the process route will permit maximum productivity and an appropriate process control system which will permit achievement of the production and quality objectives.

Jan 1, 1991

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

By Goode A, Belby P, Wardell-Johnson M

Within a short time frame of just over two years Wirralie Gold Mine has been developed from a virgin geological discovery to an operating gold mine with a mine life of six years and a production rate of 50,000 oz per annum. Construction work on the 600,000 tpa single stage crushing, two stage milling CIP plant commenced in November 1987 and was completed some seven months later at an overall cost of $A25 million. Since commissioning in May 1988 the treatment plant has exceeded design tonnage, availability and recovery. A second expansion programme in January 1989 will increase plant capacity to one million tonnes per annum with associated bullion production of 80,000 ozs per annum.

Jan 1, 1989

By Teniswood CF, Sheppard I, Mason LG

An industry initiated project, sponsored by the National Energy Research Development and Demonstration Council, has worked for two years in developing design guidelines for underground coal mining machinery.Continuous miners and shuttle cars were selected for the initial development of design guidelines as these machines were linked with 7500 lost workdays and 490 reported injuries during the preceding two years.

Jan 1, 1991

Reserves of high-grade quartz gravel, lignite, and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while opencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferrosilicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By Hodkinson I, Slight M

Over the last five years Mt Leyshon has matured into a sizeable gold mine by Australian Standards. In the later part of 1990, after commissioning of the 3.5 mtpa CIP Plant upgrade, experience indicated there was potentially additional Mill capacity beyond that being utilised at the 3.5 mtpa rate. Overall throughput was limited by crushing plant performance and high operating costs resulting from the age and condition of the main crushing plant.In addition, mining was being carried out using a mining contractor who utilised relatively small, high cost mining equipment, and on-going exploration success was also indicating that the then current mine plan would result in only a portion of the available resource being exploited.

Jan 1, 1992

By J-P Franzidis

Industrial flotation plant design is a complex process involving many aspects, one of which is the use of pilot-scale plants to test industrial plant flow sheets. Once test work on a pilot-scale has been performed, scale-up of these results to the full-scale plant must be performed. This paper describes scale-up test work performed on the Floatability Characterisation Test Rig (FCTR). The FCTR is a self-contained, highly instrumented mobile pilot plant designed to determine flotation model parameters and to develop and validate flotation plant modelling, scale-up and simulation methodologies.

Jan 1, 2004

By Golosinski T. S, Jorgenson J. D

Several methods are available for inspections of mine shafts. These involve use of inclinometers, moving beams, inertial platforms and decelerometers. Inspections which use decelerometers are of most interest since they allow assessment of conditions of shaft steelwork, conveyances and the shaft itself. This assessment is based on recording and analysing dynamic behaviour of shaft conveyances. Sample inspections of several WA shafts confirm feasibility of using this method for periodic shaft Inspections.

Jan 1, 1995

By E Villaescusa

This paper describes a methodology for the design of mine pillars at the McArthur River Mine. The pillar strength is calculated using a method that accounts for confinement, pillar geometry and intact rock properties. The average pillar stress was calculated using in situ measurements of vertical stresses at shallow depth and the tributary area method in conjunction with numerical modelling. Observations of pillar behaviour indicate that an existing pillar stability graph may be slightly conservative and further adjustments for the local rockmass conditions are needed. The results to-date indicate that all mine pillars are stable for a range of mining geometries at McArthur River Mine.

Jan 1, 1998

A new plant for grinding limestone was built at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited to meet increasing process demands expected to reach 150 tonne/day of ground limestone. Plant specifications included open- circuit wet grinding, a single ball mill, a feed sizing of minus 6 Tyler mesh, a product sizing of 100 per cent minus 200 and 95 per cent minus 325 Tyler mesh and for the plant to be unmanned during normal running. Main features of plant and equipment are described; grinding performances given, as well as operating experience since commission- ing of the plant in March, 1976.

Jan 1, 1977

By Li T

Mining of the southern 1900 copper Orebody presented a challenge due to the complex geology, geometry and simultaneous extraction of the nearby lead/zinc/silver orebody. An integrated and co-operative approach was adopted, involving geology, geomechanics, mine planning and production personnel. Successful extraction of the first 1900 Orebody stope, T496, together with the extraction of the first two lead/zinc/silver panel stopes in the immediate hangingwall of the 1900 Orebody stope was achieved as a result of this approach.

Jan 1, 1995

Studies of the morphology of seamounts within the Hawaiian, Line Islands, Gilbert and Phoenix Seamount groups indicate that the morphology and size distribution of seamounts vary significantly from one seamount group to another. The Line Islands group appears to be the most complicated of all the groups studied thus far. This group is complicated by reactivation of volcanism, which has superimposed volcanics on sedimentary rocks. These seamounts display abundant volcanic features on their summits. Seamounts within the Hawaiian seamount chain display a marked absence of volcanic features due to the . presence of thick carbonate caps. Reef platforms and sealevel benches are very common on these seamounts but are absent from seamounts in most other seamount chains in the central Pacific. Slope angles vary regionally between seamount groups. The minimum slopes are found on Necker Ridge in the central Pacific basin. The maximum slopes are found on ridge-crest seamounts. Roughness increases proportionally with mean slope angle.

Jan 1, 1987